Siemens SINUMERIK 810D Quick start guide

SINUMERIK 810D/840Di/840D SINUMERIK PCU Basesoftware (IM6)
_
_____________
_
_____________
_
_____________
_
_____________
Commissioning a system 1
Configuring the system 2
Installing software and
network operation 3
Backing up and Restoring
Data 4
SINUMERIK 810D/840Di/840D
SINUMERIK
PCU Basesoftware (IM6)
Commissioning Manual
10/2006
6FC5397-0DP10-0BA0
Valid for: Software PCU Basesoftware Version 7.6

Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
Danger
indicates that death or severe personal injury will result if proper precautions are not taken.
Warning
indicates that death or severe personal injury may result if proper precautions are not taken.
Caution
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
Caution
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
Notice
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
Warning
This device may only be used for the applications described in the catalog or the technical description and only in
connection with devices or components from other manufacturers which have been approved or recommended by
Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly
as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90437 NÜRNBERG
GERMANY
Order No.: 6FC5397-0DP10-0BA0
Edition 10/2006
Copyright © Siemens AG 2004-
2006.
Technical data subject to change

PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 iii
Table of contents
1 Commissioning a system........................................................................................................................ 1-1
1.1 Delivery condition of the system ................................................................................................ 1-1
1.1.1 Hard disk partitions .................................................................................................................... 1-2
1.1.2 System settings.......................................................................................................................... 1-3
1.2 User administration .................................................................................................................... 1-5
1.2.1 Which users are set up? ............................................................................................................ 1-5
1.2.2 Change service user.................................................................................................................. 1-6
1.2.3 Global user settings ................................................................................................................... 1-7
1.2.4 Specific user settings ............................................................................................................... 1-10
1.3 Boot up behavior of the PCU ................................................................................................... 1-12
1.3.1 Boot up of the PCU: no HMI program installed........................................................................ 1-12
1.3.2 Boot up of the PCU: HMI program already installed................................................................ 1-13
1.4 BIOS settings ........................................................................................................................... 1-14
2 Configuring the system........................................................................................................................... 2-1
2.1 Service menu functions (DOS function)..................................................................................... 2-1
2.1.1 Parameterizing the service menu (DOS)................................................................................... 2-3
2.1.2 Operating the main menu .......................................................................................................... 2-4
2.1.3 Setting the SINUMERIK HMI environment ................................................................................ 2-5
2.1.4 Starting DOS shell and checking the software version.............................................................. 2-7
2.1.5 Starting the service desktop....................................................................................................... 2-8
2.1.6 Checking the hard disk .............................................................................................................. 2-9
2.2 Configuring the operator interface ........................................................................................... 2-10
2.2.1 Storage location of HMI boot screen ....................................................................................... 2-10
2.2.2 Displaying your own boot screen............................................................................................. 2-11
2.2.3 Changing the background of the service desktop.................................................................... 2-11
2.3 User-specific settings during boot up....................................................................................... 2-12
2.3.1 Starting an HMI program during boot up ................................................................................. 2-12
2.3.2 Starting service desktop during boot up .................................................................................. 2-14
2.3.3 Starting OEM programs ........................................................................................................... 2-16
2.3.4 Enabling/disabling error log during boot up ............................................................................. 2-16
2.4 PCU with SITOP UPS module................................................................................................. 2-17
2.4.1 Starting and configuring the SITOP monitor............................................................................ 2-18
2.4.2 Configuration of the SITOP UPS module ................................................................................ 2-20
2.4.3 Configuration for exiting the HMI ............................................................................................. 2-23
3 Installing software and network operation............................................................................................... 3-1
3.1 Installing software and software update ....................................................................................3-1
3.1.1 Installing an upgrade or Service Pack ....................................................................................... 3-1
3.1.2 “Silently” installing an upgrade or Service Pack ........................................................................ 3-2
3.1.3 Installation with FAT16 data file structure.................................................................................. 3-5
3.1.4 Installation with FAT32 data file structure.................................................................................. 3-6
3.1.5 Installation via network connection ............................................................................................ 3-8

Table of contents
PCU Basesoftware (IM6)
iv Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
3.2 Settings for network drives....................................................................................................... 3-12
3.3 Network operation with the Service desktop............................................................................ 3-18
3.3.1 Installing and authorizing SIMATIC STEP 7 ............................................................................ 3-19
3.3.2 Authorizing SIMATIC STEP 7 via the Service menu ............................................................... 3-21
4 Backing up and Restoring Data .............................................................................................................. 4-1
4.1 Backing up/restoring data with an Ethernet connection............................................................. 4-1
4.1.1 Backing up the PCU hard disk to the PG/PC hard disk ............................................................. 4-1
4.1.2 Restoring the PCU hard disk from the PG/PC hard disk ........................................................... 4-5
4.1.3 Commissioning a replacement hard disk ................................................................................. 4-11
4.2 Backing up and restoring PCU partitions locally...................................................................... 4-13
4.2.1 Backing up partitions................................................................................................................ 4-15
4.2.2 Restoring partitions .................................................................................................................. 4-17
4.2.3 Restoring Partition E: (Windows) on the PCU ......................................................................... 4-19
4.2.4 Deleting the backup image....................................................................................................... 4-21
4.2.5 Defining an emergency backup image..................................................................................... 4-22
4.2.6 Restoring the emergency backup on partition E:..................................................................... 4-24
4.3 Backing up/restoring data with a TCU configuration................................................................ 4-25
Index................................................................................................................................................ Index-1

PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-1
Commissioning a system 1
1.1 1.1 Delivery condition of the system
Overview
The high-performance SINUMERIK PCU 50 features interfaces for communication via
Ethernet and PROFIBUS DP/MPI, leaving the integrated slots free for other tasks. The USB
port at the back of the device provides "hot plug and play" functionality for a standard PC
keyboard and mouse. The SINUMERIK PCU 50 is shipped with the Windows XP
ProEmbSys operating system and the Ghost backup software, versions 6 and 7.
The HMI-Advanced user interface software can be ordered additionally.
References: "Operator Components" Manual
Supplied software on the PCU
The software installed on delivery of the PCU includes the components below, among
others:
MS Windows XP Professional SP2
Internet Explorer V 6.0
MPI driver V 6.03
Symantec Ghost (incl. Ghost Explorer) V 7.0 (default)
NFS client The NFS client from “Windows Services for UNIX“ is
installed on E:\SFU\NFSCLIENT.
Note
For the system component versions contained in the PCU Basesoftware, see the
C:\BaseVers.txt file.
The software package "PCU Basesoftware Thin Client" is not included and must be ordered
and installed separately.
Documentation for all Ghost tools is supplied on the PCU’s hard disk under E:\TOOLS.

Commissioning a system
1.1 Delivery condition of the system
PCU Basesoftware (IM6)
1-2 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
1.1.1 Hard disk partitions
Division of the hard disk
The hard disk is divided into a primary partition C and an extended partition containing the
three logical drives D, E and F. Partitions C and D work with FAT16 file access and drives E
and F with NTFS file access.
The hard-disk partitioning corresponds to the grouping that is required for installing the HMI
system software onto the PCU under Windows XP. Windows XP can be used with PCU 50
V2 (566 MHz or 1.2 GHz, 10 GB or 40 GB hard disk). For reasons of data security, the HMI
system software and the Windows XP system software are distributed on the different hard
disk partitions.
Depending on the order details, the HMI system software may be pre-loaded on delivery. It is
installed subsequently by the customer the first time the system is booted up.
The following figure shows how the hard disk of the PCU is used:
DSSUR[*%*%*%
*%
86(5)17)6
(0(5*(1&<&)$7
6<67(0(17)6703'
)$7
Figure 1-1 Partitioning of hard disk (example with 10 GB)
Content of the partitions
The individual partitions are intended for the following data or already contain this data:
EMERGENCY (C:) Partition C contains DOS 6.2 together with the tools and scripts
created by the Service menu (e.g., Ghost).
TMP (D:) Used for storing Ghost images (e.g., of the status on delivery) and
local backup images.
Contains the installation directory where the software to be installed
is first copied to from a remote PG/PC, prior to the actual installation
procedure.
SYSTEM (E:) Reserved for the Windows XP software.
The Windows XP software is available on the recovery media CD via
network, in order to later install drivers or updates as needed.
USER (F:) For installing user programs.
Applications such as HMI system software (incl. data storage and
temporary data), STEP7, OEM applications for HMI, or customer-
specific applications should only be installed here.

Commissioning a system
1.1 Delivery condition of the system
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-3
Notice
All of the applications must be exclusively installed on USER (F:); even if these applications
have a different drive set as the default drive in their installation path.
The names EMERGENCY, TMP, SYSTEM, USER must not be changed; otherwise the
"ServiceCenter" (see Section 4) will no longer function.
1.1.2 System settings
PCU default setting
A PCU 50 V2 has one integrated Ethernet interface. This is preset as a default DHCP client
for the address reference from a company network. A second additional Ethernet card must
be installed with an Ethernet interface to connect this PCU to an NCU or a TCU.
Note
If no fixed Internet address is set for the Ethernet "on-board" and no DHCP server is
available on the network, a so-called APIPA address is assigned under Windows XP. Boot
manager is extended by at least one minute (this is system-related and not an error on the
part of the HMI Manager).
The software package "PCU Basesoftware Thin Client" must be installed on the PCU if the
PCU 50 V2 is to be operated in a SINIUMERIK solution line network. When installing the
'PCU Basesoftware Thin Client' on the PCU 50 V2, the Ethernet interface on the additionally
installed Ethernet card must be set according to application.
References: Commissioning Manual Thin Client Configuration
Name of the PCU
Upon delivery of the system, a unique computer name is generated which can be read out
under: "Start" → "Settings" → "Control Panel" → "System", "Computer Name" tab.
Configuration of the operating system
For safety reasons, Windows XP has been preset as follows:
● The Autorun function is deactivated.
● Automatic Windows Update is deactivated.
● Monitoring and alerts for antivirus software and automatic update are deactivated.

Commissioning a system
1.1 Delivery condition of the system
PCU Basesoftware (IM6)
1-4 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
● Links used to call up Internet Explorer from the service desktop and the start menu are
removed.
● Remote Procedure Call (RPC) is possible for calls that are not connected.
● Firewall settings are activated on the on-board Ethernet network card. The firewall
settings are also activated if an additional Ethernet card is installed. The firewall settings
for the second network card are not deactivated until the “PCU Basesoftware Thin Client"
is installed.
Changes to Windows services
Other default settings:
Windows services: Start-up type:
Computer Browser Manual (Not started)
Error Reporting Service Disabled
Portable Media Serial Number Manual (Not started)
SSDP Discovery Service Disabled
Universal Plug and Play Host Disabled
Web Client Manual (Not started)
Wireless Zero Configuration Manual (Not started)
Preset users
Upon delivery of the system, the following users are defined at the factory:
User name Password User type Windows user group
operator operator HMI Users Operator
auduser SUNRISE Service user System administrator
siemens ***** --- System administrator
Starting ServiceCenter
Using this link on the service desktop, you can start the service center users.
In service center users, the boot up behavior of the PCU is globally set for all users or
individual users.

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-5
1.2 1.2 User administration
1.2.1 Which users are set up?
Overview
The users are managed in the "ServiceCenter Users", so that the commissioner/service user
no longer has to make corresponding settings directly in the registry.
The preset users are:
● The "auduser".
The "auduser" is a service user type of user and belongs to the system administrators'
user group. The system administrators have the user rights of a local administrator.
● The "operator"
The "operator" is an HMI user type of user and belongs to the operators' user group. The
operators have limited user rights.
For the HMI user and service user, individual settings can be configured for boot up, the HMI
program and service.
Notice
In the PCU Basesoftware version 7.6, only one service user ("auduser" is the default) and
only one HMI user with the fixed name of "operator" are supported.
User
Each user is from one user type and belongs to one user group.
User type
A user can be assigned to the following user types:
User types Task card
HMI Users •Boot up of the PCU
•Operating the HMI program
Service user •Service tasks
•Boot up of the PCU
•Operating the HMI program
The user types are implemented under Windows in user groups with various user rights.

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
1-6 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
User group
The user types are implemented via the following Windows user groups:
User group Name of the group (Windows) User Rights
Operator operator.group Restricted
System administrators Administrators local administrator
Service Desktop
The service desktop provides the service user with a Windows desktop, which is expanded
by tools and functions for service tasks, such as manage users, install software, save/restore
data, check system integrity, etc.
1.2.2 Change service user
Overview
Any other Windows user can also become the service user (instead of “auduser”) if they are
set up as a local Windows administrator or a domain user and possess local administrator
rights.
Change service user
The service user is identified in the registry by two entries: User name and user type. The
default user name is "auduser", the user type for the service user is "2".
In order to change the service user, the user who wants to be the new service user must log
into Windows with local administrator rights. Only this user has sufficient user rights to make
the entries in his user-specific branch of the registry.
The service user is registered by the following registry entries:
Reference Default
Key HKLM\SOFTWARE\Siemens\SINUMERIK\Basesoftware\<version>\HMIManager
HMIUserName Entry <user name> (STRING) auduser
HMIUserDomainName Entry <domain name> (STRING) (local)
Reference Default
Key HKCU\SOFTWARE\Siemens\SINUMERIK\Basesoftware\HMIManager
UserType Entry 2 (DWORD)
The following name must be entered under "HMIUserDomainName":
● for a local administrator: (local)
● for a domain operator: <domain name>

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-7
1.2.3 Global user settings
Principle of passing on
In the "ServiceCenter Users", set the following responses under "Users" → "Global Settings":
● Boot up behavior of the PCU
● Start the HMI program
● Behavior in service mode
The settings that are made for users under "Global Settings" are passed on to individual
users. The passed on settings can still be specifically adapted for the respective user. To do
this, the user must log in using his password.
Figure 1-2 Global user settings

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
1-8 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
Startup:
Selection Effect
Bitmap folder: - None - Directory with boot screens
Default bitmap folder: F:\hmi_adv\ib\DATA\default Directory containing default boot screens
Installing: "yes" (default) Installation privilege exists during boot up
"no" No installation privilege
Install veto dialog: "no" (default) For pending installation during the boot
up: No prompting, the installation begins
immediately.
"yes" For pending installation during the boot
up: Prompt asking whether to install.
HMI program:
Selection Effect
Start: "yes" (default) The HMI program is started.
"no" The HMI program is not started.
File: F:\hmi_adv\reg_cmd.exe
(default)
Directory of the HMI program
Task bar autohide: "no" (default) HMI program: Hide start task bar
"yes" HMI program: Show start task bar
Task bar on top: "no" (default) HMI program: Start task bar in the
background
"yes" HMI program: Start task bar on top
Service:
Selection Effect
Intro dialog: "yes" (default) Display service intro dialog
"no" Do not display service intro dialog
Logon dialog: "yes" (default) Display service logon dialog
"no" Do not display service logon dialog
Default password map: "yes" (default) The password is not case-sensitive.
"no" The password must be entered exactly as
specified.
Bitmaps folder: - None - Directory with background screens for the
service desktop
Default bitmap folder: - None - Directory with default background screens for
the service desktop
Task bar autohide: "no" (default) Service Desktop: Hide start task bar
"yes" Service Desktop: Show start task bar
Task bar on top: "no" (default) Service Desktop: Start task bar on top
"yes" Service Desktop: Start task bar in the
background

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-9
Note
If you press the "Reboot" button, the system immediately reboots (without prior prompting).
Use "Exit" to end the ServiceCenter Users.
Service dialogs during boot up
The following dialogs are shown during boot up:
● The Service Intro Dialog is shown, if no HMI program is installed or the start of the HMI
program is deactivated.
Figure 1-3 Service Intro Dialog
● If a service user wants to log in, the Service Logon Dialog is displayed:
– After pressing key <3> during boot up.
– After pressing the "Service" button in the service intro dialog.

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
1-10 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
Figure 1-4 Service Logon Dialog
1.2.4 Specific user settings
Passing on settings
The settings that are made for users under "Global Settings" are passed on to the respective
user.
Example: "operator"
After the password is entered, the settings can be user-specifically adapted. The settings
that cannot be changed are displayed with a grey background.

Commissioning a system
1.2 User administration
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-11
Figure 1-5 User settings for the "operator"

Commissioning a system
1.3 Boot up behavior of the PCU
PCU Basesoftware (IM6)
1-12 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
1.3 1.3 Boot up behavior of the PCU
1.3.1 Boot up of the PCU: no HMI program installed
Requirement
No HMI program is installed during the PCU boot up.
Ramp-up phase
,QVWDOO+0,
SURJUDP"
1R
6HUYLFHLQWUR
6HUYLFH
RU
6KXWGRZQ
6WDUW3&8UDPSXS
<HV ,QVWDOODWLRQ
SURFHGXUH 5HVWDUW
Figure 1-6 PCU bootup diagram (without HMI program)

Commissioning a system
1.3 Boot up behavior of the PCU
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-13
Explanations:
● If installation programs (such as HMI Advanced) are present in directory D:\Install, you
will be prompted during the first boot up as to whether the installation procedure should
be started. After installation is completed, you need to restart the system.
The installation can also be skipped and carried out later.
● In the service intro dialog, you can choose between "service" or "shutdown".
● Selecting "service" opens the service logon dialog.
Note
During the initial boot up of the PCU 50.3, the user can only log on as 'auduser'.
1.3.2 Boot up of the PCU: HMI program already installed
Requirement
An HMI program (e.g. HMI Advanced) is already installed.
Ramp-up phase
<HV
1R
6HUYLFHORJRQ
3UHVVEXWWRQ! <HV
6WDUW+0,
SURJUDP
6HUYLFHGHVNWRS
RU
VHUYLFHFHQWHU
6WDUW3&8UDPSXS
Figure 1-7 PCU bootup diagram (HMI program installed)

Commissioning a system
1.4 BIOS settings
PCU Basesoftware (IM6)
1-14 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
Explanations:
● If the HMI program is already installed, the PCU boots up and the HMI program is started
(default).
● During the boot up, there is a time interval for pressing key <3> when the version
information appears on the lower right of the background screen. The service logon
dialog then opens.
● After logging in as a service user, you can either start the "service desktop" in order to
carry out additional service tasks, or you can start the "ServiceCenter Users" in order to
set the boot up behavior for the individual users.
1.4 1.4 BIOS settings
Overview
The BIOS of the PCU is preset in such a way that no changes are required. The date and
time can be set under Windows or the HMI operator interface.
Notice
Your device configuration is preset for working with the software supplied with the unit. You
should only change the preset values if you have modified your device in any way, or if a
fault occurs when the unit is powered up.
Starting BIOS setup
1. Start the BIOS SETUP as follows:
Reset the device (warm or cold restart).
After the first boot up, the following message appears:
Press < F2 > to enter SETUP or <ESC> to show boot menu
2. Press the F2 key as long as the BIOS prompt appears on the screen.
The BIOS main menu opens:

Commissioning a system
1.4 BIOS settings
PCU Basesoftware (IM6)
Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0 1-15
3KRHQL[%,266HWXS8WLOLW\
,WHP6SHFLILF+HOS
6\VWHP7LPH
(6& ([LW
6\VWHP'DWH
6HOHFW,WHP
6HOHFW0HQX

6HOHFW
&KDQJH9DOXHV
6XE0HQX
)
)
6HWXS'HIDXOWV
6DYHDQG([LW
>@
(QWHU
+HOS
)
>@
'LVNHWWH$>0%@
3ULPDU\0DVWHU  >0%@
%RRW2SWLRQV
.H\ERDUG)HDWXUHV
+DUGZDUH2SWLRQV
6\VWHP0HPRU\  .%
([WHQGHG0HPRU\  .%
3ULPDU\6ODYH  >1RQH@
6HFRQGDU\0DVWHU >1RQH@
0HPRU\&DFKH
6HFRQGDU\6ODYH  >1RQH@
7DE!6KLIW7DE!RU
(QWHU!VHOHFWVILHOG
>:ULWH%DFN@
6HFXULW\ %RRW 9HUVLRQ ([LW0DLQ $GYDQFHG 3RZHU
Figure 1-8 BIOS Main Menu (Example)
BIOS setup: Defaults
The following system parameters are pre-stored on a PCU with 10 GB hard disk when it is
shipped:
Menu: Main
System parameters Defaults Custom entries
System Time hh:mm:ss
System Date MM/DD/YYYY
Disk A 1.44 MB 3½"
Primary Master 10056 MB
Primary Slave None
Secondary Master None
Secondary slave None
Memory Cache Write Back
Boot options
QuickBoot Mode Enabled
SETUP prompt Enabled
POST errors Enabled
Floppy check Disabled
Diagnostic screen Enabled

Commissioning a system
1.4 BIOS settings
PCU Basesoftware (IM6)
1-16 Commissioning Manual, 10/2006, 6FC5397-0DP10-0BA0
Keyboard features
Numlock Off
Key click Disabled
Keyboard auto-repeat rate 30 / sec
Keyboard auto-repeat delay ½ sec
Hardware Options
PCI MPI/DP Enabled
On-board Ethernet Enabled
Ethernet address 08 00 06 xx xx xx
LAN Remote Boot Enabled
Cardbus/PCMCIA slot Enabled
Fan control Enabled
SafeCard functions Enabled
Legacy USB support Enabled
CRT/LCD selection SIMULTANEOUS
LCD screensize Expanded
DSTN contrast 154
PS/2 mouse Auto Detect
Menu: Advanced
System parameters Defaults Custom entries
COM/LPT1 Configuration
Internal COM 1 Enabled
Base I/O address 3F8
Interrupt IRQ 4
Internal COM 2 Enabled
Base I/O address 2F8
Interrupt IRQ 3
Internal LPT 1 Enabled
Mode EPP / Bi-directional
PCI Configuration
PCI device slot 1
Option ROM scan Enabled
Enable master Enabled
Latency timer 0040h
PCI device slot 2