Siemens SIPLUS CMS4000 IFN VIB-A User manual

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 1
Preface 1
Product Overview 2
SIPLUSCMS4000
Installation 3
Media Converter Node (MCN11)
Wiring 4
6AT8000-1EB00-3XA0 Commissioning and Diagnosis 5
Technical Data 6
Appendix 7
Operating Instructions - English
Release 2017-06

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 2
Safety Guidelines
This document contains notices which you should observe to ensure your own personal safety as well as to avoid property damage.
The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring to property
damage only have no safety alert symbol.
Danger
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Warning
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Caution
Used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
Caution
Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in prop-
erty damage.
Notice
Used without the safety alert symbol indicates a potential situation which, if not avoided, may result in an undesirable
result or state.
When several danger levels apply, the notices of the highest level (lower number) are always displayed. If a notice refers to personal
damages with the safety alert symbol, then another notice may be added warning of property damage.
Qualified Personnel
The device / system may only be set up and operated in conjunction with this documentation. Only qualified personnel should be
allowed to install and work on the equipment. Qualified persons are defined as persons who are authorized to commission, to earth,
and to tag circuits, equipment and systems in accordance with established safety practices.
Intended Use
Please note the following:
Warning
This device and its components may only be used for the applications described in the catalog or technical description,
and only in connection with devices or components from other manufacturers approved or recommended by Siemens.
Trademarks
All designations marked with ® are registered trademarks of Siemens AG. Other designations in this documentation might be trade-
marks which, if used by third parties for their purposes, might infringe upon the rights of the proprietors.
Copyright Siemens AG 2017. All rights reserved.
Reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be
liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.
Disclaimer of Liability
We have checked the contents of this document for agreement with the hardware and software described. Since deviations cannot be
precluded entirely, we cannot guarantee full agreement. However, the data in the manual are reviewed regularly, and any necessary
corrections will be included in subsequent editions. Suggestions for improvement are welcomed.
Siemens AG
Digital Factory, Factory Automation
Systems Engineering
P.O. Box 23 55
90713 Fuerth
Germany Siemens AG 2017 Technical data subject to change

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 3
Table of Contents
1Preface.................................................................................................................................5
1.1 Purpose of the Operating Instructions.....................................................................5
1.2 Required Basic Knowledge ....................................................................................5
1.3 Validity of this Document........................................................................................5
1.4 Modification compared with the Previous Version...................................................5
1.5 CE Marking............................................................................................................5
1.6 Standards..............................................................................................................5
1.7 Directory................................................................................................................6
1.8 Recycling and Disposal..........................................................................................6
2Product Overview................................................................................................................7
2.1 What is SIPLUS CMS?...........................................................................................7
2.2 What is a Media Converter Node (MCN11)?...........................................................8
2.3 Scope of Delivery...................................................................................................9
2.4 Unpacking and Checking .......................................................................................9
3Installation.........................................................................................................................10
3.1 Installation Position, Dimensions..........................................................................10
3.2 DIN Rail...............................................................................................................11
3.2.1 Installation ...........................................................................................................11
3.2.2 Disassembling .....................................................................................................12
3.3 Mounting Angle....................................................................................................13
3.3.1 Installation ...........................................................................................................13
3.3.2 Disassembling .....................................................................................................13
3.4 Label Plate...........................................................................................................14
4 Wiring................................................................................................................................15
4.1 General Rules and Regulations for operation of MCN11.......................................15
4.2 MCN11................................................................................................................16
4.2.1 Connecting optical fiber cable (LWL)....................................................................16
4.2.2 Connecting MCN11 to the ground (SHIELD).........................................................19
4.2.3 IEEE1394 Interface (LNK)....................................................................................20
4.2.4 Cable Information.................................................................................................22
5Commissioning and Diagnosis ........................................................................................23
5.1 Commissioning and Start-up of MCN11................................................................23
5.1.1 Requirements for Commissioning.........................................................................25
5.1.2 Commissioning of MCN11....................................................................................25
5.2 Diagnosis via LED-indicators................................................................................25
6Technical Data...................................................................................................................26
6.1 Standards and Approvals.....................................................................................26
6.2 Technical Data.....................................................................................................28
6.3 Approval ..............................................................................................................29
6.4 Use of the CMS4000 in Zone 2 potentially explosive atmospheres .......................29

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 4
7Appendix...........................................................................................................................30
7.1 Order Numbers....................................................................................................30
7.2 Dimensional Drawing...........................................................................................31
7.3 Service & Support on the Internet.........................................................................32
7.4 List of Abbreviations.............................................................................................32

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 5
1 Preface
1.1 Purpose of the Operating Instructions
This operating instructions supports you to operate the Media Converter Node SIPLUS
CMS4000 MCN11, named MCN11 as peripheral device in the System SIPLUS
CMS4000.
1.2 Required Basic Knowledge
Basic knowledge of automation technology and equipment condition monitoring is nec-
essary.
This operating instructions contains a description of the components, which are valid at
the time of publishing the manual. We reserve the right, to enclose product information
with current information to new components and updated components.
1.3 Validity of this Document
This operating instructions is valid for the MCN11.
1.4 Modification compared with the Previous Version
- None
Notice
You will find the version of the operating instructions in the number of the footer: A5E02298098A-AA.
1.5 CE Marking
The Media Converter Node (MCN11) meets the requirements and objectives of the EG-
Guideline according to 2004/108/EG.
1.6 Standards
You will find detailed information in chapter 6.1 of this operation instructions.
Notice
The specified approvals are issued when the product is marked.

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 6
1.7 Directory
The operating instructions describe the hardware of the Media Converter Node MCN11.
It contains the following topics:
•Installation and wiring (Chapter 3 and 4)
•Commissioning and diagnosis (Chapter 5)
•Order Numbers (Chapter 7)
•List of abbreviations with explanation of the general definitions of the used terms
(Chapter 7)
1.8 Recycling and Disposal
The MCN11 is environmental compatibility and recyclable.
For environmentally compatible recycling and disposal of your old device contact a certi-
fied waste disposal for electronic.

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 7
2 Product Overview
2.1 What is SIPLUS CMS?
SIPLUS CMS is an industrial-suited Condition Monitoring System for technical and tech-
nological services in industrial plants. SIPLUS CMS is a modular, scalable analysis and
diagnosis system. It is optimized for reaction less measurement of analog, binary and
numerical data. SIPLUS CMS can be integrated in existing and new industrial plants.
SIPLUS CMS can be integrated into the TIA-Architecture.
Picture 1 Typical Configuration

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 8
2.2 What is a Media Converter Node (MCN11)?
Definition
The MCN11 transforms the transmitting data at physical layer from one medium (electri-
cal) to another medium (optical) and vice versa. MCN11 is used for the communication,
when the linking length is longer than 4.5 meters.
Application Area
•The MCN11 is suited for the application in the industrial environment, because of the
robust construction and the degree of protection IP67.
•The compact design of the MCN11 enables the application in space-saving ranges.
•Easy handling of MCN11 provides a fast commissioning and maintenance
•The product is designed for the application on a DIN Rail or for mounting angles.
Display
The MCN11 has two displays, one IEEE1394 connection and one optical fiber (LWL)-
cable entry.
Picture 2 Front View MCN11
Status Display:
•PWR (green LED)
•LNK (yellow LED)
IEEE1394 Connection (LNK)
Label Plate
LWL Cable Entry
Name Plate
(right device site, 2-pices)

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 9
2.3 Scope of Delivery
•Device MCN11
- incl. clamp for DIN Rail mounting
- LWL Cable entry for LWL twin connectors (other LWL Types on request)
•Operating Instructions (compact)
2.4 Unpacking and Checking
After unpacking, please check
•the packet for completeness and
•all parts for transport damages.
Warning
Do not use any parts that show signs of damage!

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 10
3 Installation
3.1 Installation Position, Dimensions
Installation Position
The MCN11 is suited for installation on a DIN rail or for attachment with mounting
angles.
Dimension and Expansion Spaces
Chart 1 Dimensions with and without DIN rail/mounting angles
Dimensions in mm MCN11 without
installation MCN11 with DIN Rail MCN11 with mounting angles
Installation face length 160 160 177
Installation height 46 46 46
Installation depth 56 65 66
Picture 3 Correct Installation Position
Caution
The minimum spaces which are specified in chapter 6.2 on top and underneath the device and in front of
the device have to be kept.

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 11
3.2 DIN Rail
Characteristics
The device can be installed on a DIN rail.
3.2.1 Installation
Requirements
The table-track is installed on the device.
Procedure Hang the upper table-track of the device on the DIN rail and push it down towards the
DIN rail so that it snaps in.
Picture 4 Installation of the device on a DIN rail.
Caution
During operation with vibration load use an attachment with mounting angels.
1
2
3

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 12
3.2.2 Disassembling
Procedure
Make sure that all electronic connection cables are dissembled professionally.
Remove the device from the DIN rail: Push the device down against the DIN rail and
hang it out.
Picture 5 Disassembly of the MCN11 from the DIN rail
1
3
2

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 13
3.3 Mounting Angle
Characteristics
The device will be installed with mounting angles on a stable base (e.g. wall,
mounting plate).
3.3.1 Installation
Requirements
The „MCN11 Mounting Set“ is necessary for the installation with mounting angles.
In the „MCN11 Mounting Set“ is a drill template included in the equipment pack.
Order Number see chapter 7.1.
Procedure
Connect the mounting angles with the included screws and ring washers to the two con-
nection positions on the device (backside top and bottom).
Install the device on a stable base.
Picture 6 Connection of the mounting angle on the device (e.g. backside below)
3.3.2 Disassembling
Procedure
Make sure that all electronic connection cables are dissembled professionally.
Demount the device from the site of installation (e.g. wall).

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 14
3.4 Label Plate
Characteristics
You can mark the device with a label plate. The label plate is exchangeable.
Exchanging the label plate
1. Push the screwdriver in the small opening on the bottom edge of the label plate and
hang it out.
Picture 7 Hang the label plate careful out
2. Push the label plate with the finger in the indentation.

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 15
4 Wiring
4.1 General Rules and Regulations for operation of MCN11
Protection against external electrical influences
The following chart shows what you have to observe for the protection of electrical influ-
ences or faults.
Chart 2 Protection against external electrical influences
At… you must ensure that …
all devices or systems, in which
the MCN11 is installed the device or system for conduction of electromagnetic failure on grounding is connected.
Supply, signal and bus lines correct wiring arrangement and installation.
Signal and bus lines a line or strand breakage should not lead to an undefined situation of
the device or system.
Grounding
See chapter 4.2.2 „Connecting MCN11 to grounding“.

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 16
4.2 MCN11
4.2.1 Connecting optical fiber cable (LWL)
1. Open the 4 screws on the device with an Allen key (SW3).
Picture 8 Open all 4 screws
2. Release only the screwcap of the screw connection (PG-screwing) and pull the
„SC/PC-plug“ of the LWL single conductor in the right position through the screwcap.
Picture 9 Release screwcap
3. Remove the sealing insert and insert the LWL-single connectors in the suited lead-
through of the folding sealing insert.
Caution
Avoid a mechanical overload (e.g. bending) of the optical fiber cable!
Cable insert
Screwcap

Operating Instructions SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 17
4. Insert the „SC/PC-plug“ of the LWL-single connectors separately through the cable
entry in the box.
Picture 10 LWL-cable entry configuration
5. Connecting „SC/PC-Plugs“.
Picture 11 Connecting twin cable (View on the device like in picture 12 shown)
Caution
Please consider, when connecting the plug that the transmitter (Device 1) is connected with the receiver
(Device 2).
▼▲ ▼▲
Device 1
Sealing insert
Case screw (4x)
SC/PC-plug
▼Transmitter Connector
▲Receiver Connector
Device 2
Screwcap
Cable entry

Operating Instructions
SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Betriebsanleitung, 06/2017, A5E02298098A-AA 18
6. Slide the sealing insert flush in the cable entry so that the LWL-single connector lays
parallel in the box (in order to avoid a mechanical overload of LWL).
7. Screw and tighten the screwcap on to the cable entry. Recommended tightening
torque: 10Nm
Picture 12 Finished installation
8. Close the casing cover and screw the 4 included screws (from 1) tight. The recom-
mended torque: 3Nm.
Caution
Only when the installation is correct, the screwcap fits tight and the cover screw fits tight the protection
category IP67 is guaranteed.
Never pull and insert optical fiber, when the ambient temperature is 0° Celsius and below (risk of break-
age).

Operating Instructions
SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 19
4.2.2 Connecting MCN11 to the ground (SHIELD)
The earth connection has to be implemented with cable cross section of 2,5mm2
1. Isolate the grounding cable and squeeze a cable lug at the end of the line (M4 ring
eye).
2. Screw the cable lug to the device as shown in the picture. The recommended torque
is 3 Nm.
Picture 13 Connecting MCN11 to the ground (SHIELD)

Operating Instructions
SIPLUS CMS4000 MCN11
SIPLUS CMS4000 MCN11
Operating Instructions, 06/2017, A5E02298098A-AA 20
4.2.3 IEEE1394 Interface (LNK)
Connect the M12 connector on the front side of the box in the 8-pin socket plug (LNK).
For this purpose use the cable with the order number (MLFB) 6AT8000-2AB20-2AA2.
Caution
Using standard SIPLUS CMS cables is necessary. In case of using self-made cable connection there is no
warranty assumed.
The pictures 14, 15 and 16 shall only explain the concept of the plug type. The principle handling stays the
same.
1. Push the M12 connector in vertical position in the socket plug, so that the slot from the
connector and knurled ring nut are superposed.
Picture 14 Connecting M12 connector
Knurled ring nut
Socket plug
M12 connector