Siemens SIMATIC ET 200SP User manual

Manual
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
09/2018Edition
ET 200SP
siemens.com
SIMATIC

SIMATIC
ET 200SP
Analog input module AI 2xSG 4-/6-
wire HS (7MH4134-6LB00-0DA0)
Manual
7MH4134-6LB00-0DA0
09/2018
A5E41867508A-AB
Preface
Safety instructions 1
Documentation Guide 2
Product overview 3
Mounting 4
Connecting 5
Parameters/address space 6
Interrupts/diagnostics
interrupts 7
Service and maintenance 8
Technical specifications 9
Accessories 10
Parameter data record A
Representation of analog
values B

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E41867508A
Ⓟ 09/2018 Subject to change
Copyright © Siemens AG 2017 - 2018.
All rights reserved

Preface
Purpose of the documentation
This manual supplements the ET 200SP distributed I/O system system manual.
Functions that generally relate to the system are described in this system manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Conventions
CPU: The term "CPU" as used in this manual refers to both the central modules of the S7-1500
automation system and to the CPUs/interface modules of the ET 200SP distributed I/O system.
STEP 7: We use "STEP 7" as synonym for all versions of "STEP 7 (TIA Portal)" to refer to the
configuration and programming software in this documentation.
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
CAUTION
To prevent injury, read the manual before use.
Document history
The overview below summarizes the most important changes in the documentation when
compared to the previous edition.
The most important changes in the documentation when compared with the respective
previous edition are given in the table below.
Manual edition Comments
09/2018 Section "Mounting (Page 15)" revised
09/2017 Initial release
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 3

Product compatibility
The following table describes compatibility between manual edition, device revision,
engineering system and the engineering system.
Manual edition Comments Device revision Engineering system
09/2018 - FW: 1.0.0 or higher STEP 7 TIA Portal V14 SP1 or higher
STEP 7 V5.6 or higher
09/2017 Initial release FW: 1.0.0 or higher STEP 7 TIA Portal V14 SP1 or higher
STEP 7 V5.6 or higher
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines and
networks. Systems, machines and components should only be connected to the enterprise
network or the internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit:
http://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends to apply product updates as soon as available and to always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
http://www.siemens.com/industrialsecurity.
Preface
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
4Manual, 09/2018, A5E41867508A-AB

Table of contents
Preface.........................................................................................................................................................3
1Safety instructions........................................................................................................................................7
2Documentation Guide...................................................................................................................................9
3Product overview........................................................................................................................................13
4 Mounting.....................................................................................................................................................15
4.1 Safety notices for installation.................................................................................................15
4.2 Safety information according to FM and UL...........................................................................16
4.3 Mounting on the SIMATIC ET 200SP....................................................................................17
5 Connecting.................................................................................................................................................19
5.1 Wiring and block diagram.......................................................................................................19
6 Parameters/address space.........................................................................................................................23
6.1 Measurement types and measuring ranges...........................................................................23
6.2 Parameters.............................................................................................................................24
6.3 Description of parameters......................................................................................................26
6.4 Oversampling.........................................................................................................................28
6.5 Address space.......................................................................................................................31
6.6 Input lock................................................................................................................................35
7 Interrupts/diagnostics interrupts.................................................................................................................37
7.1 Status and error displays.......................................................................................................37
7.2 Interrupts................................................................................................................................39
7.3 Diagnostics alarms.................................................................................................................41
8 Service and maintenance...........................................................................................................................43
8.1 Basic safety instructions.........................................................................................................43
9 Technical specifications..............................................................................................................................45
9.1 Mechanical requirements and data........................................................................................48
9.2 Electrical, EMC and climatic requirements.............................................................................49
9.3 Approvals...............................................................................................................................53
10 Accessories................................................................................................................................................55
10.1 BaseUnit type A0 (essential)..................................................................................................55
A Parameter data record................................................................................................................................57
A.1 Dependencies when configuring with GSD file......................................................................57
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 5

A.2 Parameter assignment...........................................................................................................58
A.3 Parameter data record 128....................................................................................................59
A.4 Parameter data records 0 and 1............................................................................................64
A.5 Parameters specifications......................................................................................................68
B Representation of analog values................................................................................................................69
B.1 Representation of analog values for analog inputs................................................................69
B.2 Representation of the input range..........................................................................................70
B.3 Analog value representation..................................................................................................71
Index...........................................................................................................................................................73
Table of contents
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
6Manual, 09/2018, A5E41867508A-AB

Safety instructions 1
Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety
notices in addition to the general safety notices for protection against explosion:
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations
only.
This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous
locations only.
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 7

Safety instructions
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
8Manual, 09/2018, A5E41867508A-AB

Documentation Guide 2
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
%DVLFLQIRUPDWLRQ'HYLFHLQIRUPDWLRQ*HQHUDOLQIRUPDWLRQವ'LDJQRVWLFVವ&RPPXQLFDWLRQವ:HEVHUYHUವ'HVLJQLQJLQWHUIHUHQFHIUHHFRQWUROOHUVವ&\FOHDQGUHVSRQVHWLPHVವ352),1(7ವ352),%86ವ(763V\VWHPPDQXDOವ7,$3RUWDORQOLQHKHOS)XQFWLRQPDQXDOVRQJHQHUDOWRSLFV,QIRUPDWLRQDERXWWKHV\VWHPವ&38Vವ,QWHUIDFHPRGXOHVವ'LJLWDOPRGXOHVವ$QDORJPRGXOHVವ0RWRUVWDUWHUVವ%DVH8QLWVವ6HUYHUPRGXOHವ&RPPXQLFDWLRQPRGXOHವ7HFKQRORJ\PRGXOHV0DQXDOVZLWKGHWDLOHGLQIRUPDWLRQDERXWPRGXOHV
Basic information
The system manual describes in detail the configuration, installation, wiring and commissioning
of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help supports you in
the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion control
and OPC UA.
You can download the documentation free of charge from the Internet (http://w3.siemens.com/
mcms/industrial-automation-systems-simatic/en/manual-overview/tech-doc-et200/Pages/
Default.aspx).
Changes and supplements to the manuals are documented in a Product Information.
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 9

You can download the product information free of charge from the Internet (https://
support.industry.siemens.com/cs/us/en/view/73021864).
Manual Collection ET 200SP
The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet (http://support.automation.siemens.com/
WW/view/en/84133942).
"mySupport"
With "mySupport", your personal workspace, you make the most of your Industry Online
Support.
In "mySupport" you can store filters, favorites and tags, request CAx data and put together
your personal library in the Documentation area. Furthermore, your data is automatically filled
into support requests and you always have an overview of your current requests.
You need to register once to use the full functionality of "mySupport".
You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
In the Documentation area of "mySupport", you have the possibility to combine complete
manuals or parts of them to make your own manual.
You can export the manual in PDF format or in an editable format.
You can find "mySupport" - Documentation in the Internet (http://
support.industry.siemens.com/My/ww/en/documentation).
"mySupport" - CAx Data
In the CAx Data area of "mySupport", you can have access the latest product data for your
CAx or CAe system.
You configure your own download package with a few clicks.
In doing so you can select:
● Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
● Manuals, characteristics, operating manuals, certificates
● Product master data
You can find "mySupport" - CAx Data in the Internet (http://support.industry.siemens.com/my/
ww/en/CAxOnline).
Documentation Guide
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
10 Manual, 09/2018, A5E41867508A-AB

Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find the application examples on the Internet (https://support.industry.siemens.com/
sc/ww/en/sc/2054).
TIA Selection Tool
With the TIA Selection Tool, you can select, configure and order devices for Totally Integrated
Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product selection
or product configuration.
You can find the TIA Selection Tool on the Internet (http://w3.siemens.com/mcms/topics/en/
simatic/tia-selection-tool).
SIMATIC Automation Tool
You can use the SIMATIC Automation Tool to run commissioning and maintenance activities
simultaneously on various SIMATIC S7 stations as a bulk operation independently of the TIA
Portal.
The SIMATIC Automation Tool provides a multitude of functions:
● Scanning of a PROFINET/Ethernet network and identification of all connected CPUs
● Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a CPU
● Transfer of the data and the programming device/PC time converted to UTC time to the
module
● Program download to CPU
● Operating mode switchover RUN/STOP
● Localization of the CPU by means of LED flashing
● Reading out CPU error information
● Reading the CPU diagnostic buffer
● Reset to factory settings
● Updating the firmware of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet (https://
support.industry.siemens.com/cs/ww/en/view/98161300).
Documentation Guide
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 11

PRONETA
With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network
during commissioning. PRONETA features two core functions:
● The topology overview independently scans PROFINET and all connected components.
● The IO check is a fast test of the wiring and the module configuration of a system.
You can find SIEMENS PRONETA on the Internet (https://support.industry.siemens.com/cs/
ww/en/view/67460624).
Documentation Guide
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
12 Manual, 09/2018, A5E41867508A-AB

Product overview 3
View of the module
AI
2xU/I 2-/4-wire
DIAG
AI0
F0
AI1
F1
1
3
5
7
9
11
13
15
L+
2
4
6
8
10
12
14
16
M
U0+
U0-
U1+
U1-
PWR
CC00
V 1.0.0
AI 2-/4-wire
AI URES
24VDC
MAX. 10A
6ES7134-6HB00-0DA1
HS
I0+
I0-
I1+
I1-
UV0
M0
UV1
M1
RES
RES
RES
RES
;

①Function class ⑦LED for supply voltage
②Color labeling module type ⑧LEDs for channel status
③Function and firmware version ⑨Connection diagram
④Color code for selecting the color-
coded labels
⑩2D matrix code
⑤BaseUnit type ⑪LED for diagnostics
⑥Article number ⑫Module type and designation
Figure 3-1 View of the AI 2xSG 4-/6-wire HS module
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 13

Properties
The module has the following technical properties:
● Analog input module with 2 inputs
● Measurement type voltage of 4-wire and 6-wire strain gauges (full bridges)
4.85 VDC supply voltage of full bridge
● Input ranges
– ± 0.5 ... 320 mV/V, resolution 28 bits including sign
– 16-bit oversampling including sign
● Electrically isolated from supply voltage L+
● Configurable diagnostics (per channel)
● Hardware interrupt on limit violation can be set per channel (two high and two low limits per
channel)
The module supports the following functions:
● Firmware update
● I&M identification data
● Reconfiguration in RUN
● PROFIenergy
● Isochronous mode
● Oversampling
Accessories
The following accessories must be ordered separately:
● Labeling strips
● Reference identification label
● Shield connector
See also
You can find more information on accessories in the ET 200SP distributed I/O system system
manual.
Product overview
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
14 Manual, 09/2018, A5E41867508A-AB

Mounting 4
4.1 Safety notices for installation
Safety notices
When installing the device, keep to the safety notices listed below.
WARNING
If a device is operated in an ambient temperature of more than 50 °C, the temperature of the
device housing may be higher than 70 °C. The device must therefore be installed so that it
is only accessible to service personnel or users that are aware of the reason for restricted
access and the required safety measures at an ambient temperature higher than 50 °C.
WARNING
If the device is installed in a cabinet, the inner temperature of the cabinet corresponds to the
ambient temperature of the device.
Safety notices on use in hazardous areas
General safety notices relating to protection against explosion
WARNING
EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.
WARNING
Substitution of components may impair suitability of the equipment.
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 15

4.2 Safety information according to FM and UL
Safety information for use according to FM and UL
If you use the device under FM conditions you must also keep to the following safety notices
in addition to the general safety notices for protection against explosion:
WARNING
Substitution of components may impair suitability for Division 2.
WARNING
Do not remove or replace while circuit is live when a flammable or combustible atmosphere
is present.
WARNING
Explosion hazard
Do not disconnect equipment when a flammable or combustible atmosphere is present.
WARNING
EXPLOSION HAZARD
The device is designed for operation in closed housing or control cabinet. The inner service
temperature of the enclosure/control cabinet corresponds to the ambient temperature of the
module. Use cables with a maximum permitted operating temperature of at least 20 °C higher
than the maximum ambient temperature.
WARNING
Wall mounting outside of the control cabinet or housing does not fulfill the requirements of
the FM approval.
WARNING
Wall mounting is only permitted if the requirements for the housing, the installation
regulations, the clearance and separating regulations for the control cabinets or housings are
adhered to. The control cabinet cover or housing must be secured so that it can only be
opened with a tool. An appropriate strain-relief assembly for the cable must be used.
Note
You must not install the device on a wall in hazardous areas.
Mounting
4.2 Safety information according to FM and UL
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
16 Manual, 09/2018, A5E41867508A-AB

4.3 Mounting on the SIMATIC ET 200SP
The electronic weighing system described here is a module of the SIMATIC ET 200SP series
and can be directly connected to the automation system's bus system. The 15 mm wide module
has very low installation and cabling requirements.
The module is snapped onto the ET 200SP base unit (BU). You must use base units of type
A0 (→ Accessories (Page 55)).
The load cells, power supply and serial interfaces are connected via the terminal box.
Figure 4-1 Installation of the I/O or SIWAREX modules
Mounting
4.3 Mounting on the SIMATIC ET 200SP
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
Manual, 09/2018, A5E41867508A-AB 17

Mounting
4.3 Mounting on the SIMATIC ET 200SP
Analog input module AI 2xSG 4-/6-wire HS (7MH4134-6LB00-0DA0)
18 Manual, 09/2018, A5E41867508A-AB