Siemens XC1001-A Manual

A6V10257473_e_en_-- Building Technologies
2015-03-04 Control Products and System
XC10
Extinguishing control unit
XC1001-A / XC1005-A /
XC1003-A
Installation
Commissioning
Maintenance

© Siemens Switzerland Ltd, 2015
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these
rights and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third
party without our prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.

3
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
1About this document...........................................................................7
2Safety instructions..............................................................................9
2.1 Danger levels........................................................................................9
2.2 Safety instructions.................................................................................9
2.3 Standards and directives complied with...............................................10
3Standards..........................................................................................11
4Overview............................................................................................12
4.1 XC1001-A...........................................................................................12
4.2 XC1005-A...........................................................................................13
4.3 XC1003-A...........................................................................................14
4.4 FCP1004-E.........................................................................................15
4.5 XCM1002............................................................................................16
4.6 User interface......................................................................................18
5Features.............................................................................................21
6Installation.........................................................................................22
6.1 XC1001-A / XC1005-A ........................................................................22
6.2 XC1003-A...........................................................................................24
6.3 User interface labels............................................................................28
7Connections ......................................................................................29
7.1 Mains..................................................................................................29
7.2 Batteries..............................................................................................29
7.3 Fire detectors/Manual release control buttons......................................31
7.4 Monitored inputs..................................................................................33
7.5 Control inputs......................................................................................35
7.6 Monitored control outputs....................................................................36
7.7 Programmable outputs........................................................................39
7.8 24V power supply output.....................................................................42
7.9 Repeater terminal and repeater display...............................................42
8Multi-sector installation ....................................................................43
8.1 Functional description..........................................................................43
8.2 Detailed description.............................................................................45
8.3 Installation and wiring..........................................................................48
8.4 Modules technical specification ...........................................................49
9Accessories.......................................................................................50
9.1 FCA1007 – Key switch........................................................................50
9.2 FDCI222 / FDCIO222 – Input/output interfaces....................................50
9.3 Remote transmitter..............................................................................50
9.4 Repeaters...........................................................................................51
10 Operating access levels....................................................................56
10.1 Operating access level 1.....................................................................56
10.2 Operating access level 2.....................................................................56
10.3 Operating access level 3A...................................................................56
10.4 Operating access level 3B...................................................................56
11 Extinguishing process diagrams......................................................57

4
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
12 Programming..................................................................................... 58
12.1 Before starting.....................................................................................58
12.2 Presettings..........................................................................................59
12.3 Steps 01 to 04 - Time duration settings................................................62
12.4 Step 05 - Sounders.............................................................................64
12.5 Steps 06 to 09 - Remote transmission.................................................64
12.6 Steps 10 to 14 - Monitored outputs 1 to 5............................................65
12.7 Steps 15 to 19 - Relay contact 1 to 5...................................................66
12.8 Steps 20 to 27 - Driver outputs 1 to 8 ..................................................67
12.9 Steps 28 to 31 - Monitored inputs 1 to 4..............................................68
12.10 Steps 32 to 38 - Reset.........................................................................70
12.11 Steps 39 to 43 - Operation ..................................................................70
12.12 Steps 44 to 47 - Faults........................................................................71
12.13 Steps 48 to 51 - Non monitored control inputs 1 to 4............................71
12.14 Steps 52 to 55 - Detection zones.........................................................72
12.15 Steps 56 to 57 - Operating access level...............................................73
12.16 Step 58 - Multi-sector..........................................................................73
12.17 Step 59 - Detector type........................................................................73
12.18 Steps 60 to 61 - Repeaters..................................................................73
12.19 Step 62 - Loss of agent in multi-sector application...............................74
12.20 Steps 63 to 64 - Fire damper...............................................................74
12.21 Step 65 to 66 - Pre-discharged warning time in manual release........... 75
12.22 Step 67 – Operation if “Discharge” is activated in standby ...................76
13 Commissioning.................................................................................77
13.1 Powering.............................................................................................77
13.2 Monitored control outputs 4 and 5 calibration.......................................77
13.3 System test......................................................................................... 78
13.4 Commissioning validation....................................................................78
14 Maintenance......................................................................................79
14.1 Preventive maintenance...................................................................... 79
14.2 Detailed fault display........................................................................... 82
15 Test functions ................................................................................... 84
15.1 Led test...............................................................................................84
15.2 Sounder test........................................................................................84
15.3 Warning panels test.............................................................................84
15.4 RT-alarm test......................................................................................85
15.5 RT-fault test ........................................................................................85
15.6 System test......................................................................................... 85
15.7 Individual output test ...........................................................................86
15.8 Zone test.............................................................................................87
15.9 Manual release test.............................................................................87
16 Advanced functions.......................................................................... 88
16.1 Checksum...........................................................................................88
16.2 Alarm counter......................................................................................88
17 Special functions ..............................................................................89
17.1 Anticipated Silence Sounders.............................................................. 89
17.2 Anticipated Reset................................................................................ 89
17.3 Extract fan...........................................................................................89

5
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
18 Connection to Sinteso / Cerberus PRO panels................................90
18.1 XC10 zone..........................................................................................90
18.2 Detectors connected to XC10 panel ....................................................91
18.3 Detectors connected to Sinteso / Cerberus PRO panel........................94
19 Maintenance PC ................................................................................97
20 Components and spare parts...........................................................98

6
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04

About this document
7
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
1 About this document
Purpose of the document
This document describes the installation, the commissioning and the maintenance
of the XC100x-A equipment. It provides an overview of the structure and functions
of the system as a whole as well as of the individual devices.
While following the instructions, a reliable operation is assured.
Scope
The information contained in this document is valid for the market package MP2.3.
The document also contains information on country-specific components. Country-
specific components are marked with square brackets, e. g. [FR], and may not be
sold/used in your country.
Target audience
This document and the information contained therein are aimed at the target
groups defined below:
Personnel Activity Qualification
Product manager – Performs local product management
– Responsible for exchanging information
between the headquarters and his/her Regional
Company (RC) for his/her productrange
– Has suitable specialist training for the
function and for the product range
– Has attended the PM training courses
Project manager – Performs project management
– Coordinates the use of all persons and
resources involved in the project according to
schedule
– Continuously supplies information necessary for
project realisation
– Has suitable specialist training for the
– function, scale of the project and product
range
– Has attended the training courses for
Project Managers
Installer – Assembles and installs the components at the
place of installation
– Performs a subsequent check of the installation
– Has received specialized training in the area
of building installation technology or
electrical installations
Commissioning personnel – Configure the product at the place of installation
according to customer specific requirements
– Check the product operability and release the
product for use by the operator
– Search for and correct malfunctions
– Has suitable specialist training for the
function and for the product range
– Have attended the training courses for
commissioning personnel
Maintenance personnel – Carry out all maintenance work and check for
correct functioning – Has suitable specialist training for the function and for the product range
Reference documents
Designation Heading
A6V10257477 XC10 Extinguishing control unit
Operating manual
001204 Fire alarm signal in areas at risk of explosion
Principles, applications, installation, maintenance
Identification of the document
Location Definition
Title page – Short name
– Name in full
– Document purpose
Last page bottom left-hand side – Document no. (number-modification index-language-country)
– Date of issue
Last page bottom right-hand
side – User's guide – Register

About this document
8
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
Revision history
Document no. Edition date Brief description
A6V10257473_e_en_-- 03.2015 - MP2.3 SR2
A6V10257473_d_en_-- 04.2012 - MP2.3 SR1
A6V10257473_c_en_-- 09.2010 - chap. 4.5 updated (fig. 5 and table)
- chap 7.2.1 added: method for calculation of the battery
capacity
- chap. 7.3: fig. 7.15 updated
- chap. 8 updated
- chap. 8.3: fig. 31 updated (loss of agent is normally
closed)
- chap 9.4 added: description of repeater display and
repeater terminal
- chap 12.1: procedure step 5 updated
- chap 12.2: country pre-settings updated
- chap 12.9: step 30 option 04 updated
- chap 12.18 added (step 60)
- chap 13.1 updated (paragraph number)
- chap 13.2 updated: warning for the calibration added
- chap 14.1 updated
- chap 14.2 updated (10s instead of 5s)
- chap. 15, 16, 17 updated: several wording
- chap 18 added
- chap. 19, 20 updated
- CE marking papers added at the end of the document
A6V10257473_b_en_-- 01/2010 Corrections after field tests:
- Chap. 3: Standards / 4.19 monitoring the status of
components (spelling mistake)
- Chap.4: fig 4 updated
- Chap. 6.3 label for XC1003-A is Pos. 8 not Pos.4
- Chap. 7.6.2 …. “to equipment outside” (spelling
mistake)
- Chap 7.8: 24V polarity output was wrong. 24V(+) is on
X5-3 and 24V(-) is on X5-4
- Chap. 8.2: note added for the connection of the 24V
power supply
- Chap 8.3: fig 31 modified: resistor 3.3k on RS485 line
removed
- Chap 11: fig 33 and 34 updated
- Chap 14.2: PMI picture is added on the top of the
description table, for an easier checking
- Chap. 16.2: access code for the alarm counter was
wrong
- Spelling mistakes
A6V10257473_a_en_-- 11/2009 First edition MP2.1

Safety instructions
9
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
2 Safety instructions
2.1 Danger levels
The following pictograms indicate the possible danger levels, their severity and
consequences.
DANGER Imminent danger!
èSerious injuries or death.
WARNING Potentially dangerous situation
èSerious injuries or death.
CAUTION Potentially dangerous situation
èLight injuries or material damage.
NOTE Important information requiring special attention.
2.2 Safety instructions
Products are developed and manufactured in accordance with the applicable
international and European security standards.
The local rules of installation, exploitation and destruction of the product apply and
must be respected just like the safety instructions which appear in the
documentation of the product.
Electric installations
CAUTION Interventions on wiring should be carried out only by qualified personnel.
CAUTION Respect the safety instructions in explosive zone.
lHardware must not be powered during commissioning and maintenance
lAffix an external label “DANGER external voltage” on the terminals connected to
an external voltage source
lSeparately lay the power lines towards the control unit. They must be fitted with
their own, clearly identified fuses
lGround in accordance with the local security standards
Assembly, installation, commissioning and maintenance
lIf any tools or accessories such as ladders are required, safe and suitable
devices must be used
lWhen the extinguishing control panel is started up, it must be ensured that no
instable conditions can occur
lControls may only be set to normal function when the product operability has
been completely tested and the system has been handed over to the customer.
lControl release for testing should not damage the installation
lAvoid the inopportune release of RT-alarm
lInform the reception station before an RT-alarm test
lInstallation and commissioning shall be performed by trained personal

Safety instructions
10
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
Product operation check
lInform the personnel of the formation of a smoke cloud and presence of noise
lInform the personnel before alarm devices check and anticipate possible panic
reactions
lWarn the alarm reception centers and the fault reception stations connected to
the system before carrying out the tests
Design modifications of systems and products
lModifications to the system and to individual products may lead to faults,
malfunctioning and safety risks
lIntended system modifications or extensions require written approval from
Siemens and the relevant safety authorities
Components and spare parts
lComponents and spare parts must comply with the technical specifications
defined by Siemens. Only use products recommended or prescribed by Siemens
lOnly use fuses with the specified fuse characteristics
lWrong battery types and improper battery changing lead to a risk of explosion.
Only use the same battery type or an equivalent type recommended by Siemens
lBatteries must be disposed of in an environmentally friendly manner. Country
specific directives and regulations must be observed. They must be deposited at
the collection places assigned to this purpose.
lNote that the cylinders containing the extinguishing agent are under pressure
and that they must consequently be replaced in accordance with the safety
instructions in force
Disregard of the safety regulations
Before they are delivered, products are tested to ensure they function correctly
when used properly. Siemens disclaims all liability for damage or injuries caused
by the incorrect application of the instructions or the disregard of danger warnings
contained in the documentation. This applies in particular to:
lPersonal injuries or damage to property caused by improper use and incorrect
application
lPersonal injuries or damage to property caused by disregarding safety
instructions in the documentation or on the product
lPersonal injury or damage to property caused by poor maintenance or lack of
maintenance
2.3 Standards and directives complied with
A list of the standards and directives complied with is available at your Siemens
contact partner.

Standards
11
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
3 Standards
In addition to the requirements of EN12094-1 and EN54-2, the XC100x-A control
panel complies with the following optional functions:
EN 12094-1
Clause Description
4.17 Delay of extinguishing signal
4.18 Signal representing the flow of extinguishing agent
4.19 Monitoring the status of components
4.20 Emergency hold device
4.21 Control of flooding time
4.23 Manual only mode
4.24 Triggering signals to equipment within the system
4.26 Triggering of equipment outside the system
4.27 Emergency abort device
4.29 Release of the extinguishing media for selected flooding zones (only for XC1003-A)
4.30 Activation of alarm device with different signals
EN 54-2 / A1
Clause Description
7.8 Output to fire alarm devices (Item C – EN54-1)
7.9.1 Control of fire alarm routing equipment (Item E – EN54-1)
7.12.1 Dependencies on more than one alarm signal (Type A)
7.13 Alarm counter (only with XC1005-A)
8.3 Fault signals from point
8.4 Total loss of the power supply
8.9 Output to fault warning routing equipment (Item J – EN54-1)
10 Test condition
Following additional functions are also available:
- transmission of information's outside the panel:
8 programmable digital outputs
programmable relay contacts
- reception of information's from outside:
control inputs (3 are programmable)
- 24V power supply output

Overview
12
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4 Overview
The equipment is declined in 3 versions:
- Wall mounting cabinet: XC1001-A / XC1005-A
- 19” rack cabinet: XC1003-A
4.1 XC1001-A
System ON
Silence
buzzer
Silence
Re-sound
Sounders
Automatic blocked
Activated
Mode
Operating ac ce ss
Earth fault
Systemfault
Disable
Fault
Manual blocked
Manual release
Released
Detec tor Zone 1
………………………………….
Mechanical blocked
Loss of agent
Incorrec t status Emergency
hold
Sounders
Fire contr ols
Enab le
Disab le
Detectortest
Fire alarm
Remote ransmi ssion
Disa ble
Test
Enable
Detec tor Zone 2
………………………………….
Detec tor Zone 3
………………………………….
432
1
2
Disable
Test
Enable
Disable
Test
Enable
Disa ble
Test
Enable
Power s upply
Reset
RT-fault
RT-alarm
Actuators
Led test
Enab le
Disab le
Exti nguishing contro l:
… …………………………………………………..
s
XC1001-A EN 12094 -1 ClassA
EN54-4/ EN54-2 1116 - CPD – xxx
Fig. 1 XC1001-A
1 FCP1004-E power supply unit with charger
2 XCM1002 mainboard
3 4.5 A/h batteries
4 DIN rail for accessory mounting (Z3B171 relay module)

Overview
13
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4.2 XC1005-A
Fig. 2 XC1005-A
1 FCP1004-E power supply unit with charger
2 XCM1002 mainboard
3 17 A/h batteries
4 DIN rail for accessory mounting (Z3B171 relay module)
5 FDCI / FDCIO222 module for the connection to a fire detection system
(option)

Overview
14
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4.3 XC1003-A
Fig. 3 XC1003-A
1 FCP1004-E power supply unit with charger
2 XCM1002 mainboard
3 Removable mainboard holder
4 4.5 A/h or 7.2 A/h batteries
5 DIN rail for accessory mounting (Z3B171 relay module, XCA1030 multi-sector
modules, etc.)
6 FDCI / FDCIO222 module for the connection to a fire detection system
(option)

Overview
15
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4.4 FCP1004-E
Fig. 4 FCP1004-E power supply unit
Mark Function Remarks
1 Mains voltage setting Shunt ON = 115VCA,shunt OFF = 230VCA
2 Mains terminal block
3 Mains fuse 4A / 250V
4 System start without mains power Shunt the 2 terminals with a jumper and
remove after system start
5 Temperature sensor for battery charging voltage compensation Do not cover
6 Internal green LED «Mains operation» but visible from the front Not lit if no mains voltage
7 Battery connection
8 XCM1002 main board connection
Security level of terminal blocks 1 and 2: Dangerous voltage
Security level of other terminal blocks: SELV (Safety Extra Low Voltage)

Overview
16
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4.5 XCM1002
32
2411
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
10
7
1
2
3
5
6
8
9
4X23
X24
ON
12
X8
X3X4
X28
X1
F3
F6 F5 F4
F2 F1
X14 X15 X16 X17
X13
X18
X26
S1
X21
1
X11
1X12
X10X27 1X9
1
X7X6
11
X5 11
1
S18
X35
X20
41 2 3
5
6
7
8
9
10
11
12
13
14
15
1
Fig. 5 XCM1002 board
Setting elements
X3 Internal buzzer Enable/Disable Jumper up (factory setting) : buzzer enabled
Jumper down : buzzer disabled (only for servicing)
X4 Type of power supply Jumper up (factory setting) : FCP1004-E
Jumper down : do not use (for further use of external power supply)
X8 Operating access Level 2 Jumper on theleft: Level 2 permanent access
1 – 2: external key switch (option)
X13 Relay contact type 1
(NO or NC) Jumper up : NC contact Jumper down (factory setting) : NO contact
X14 Relay contact type 5
(NO or NC) Jumper on the right : NC contact Jumper on the left (factory setting) : NO contact
X15 Relay contact type 4
(NO or NC) Jumper on the right : NC contact Jumper on the left (factory setting) : NO contact
X16 Relay contact type 3
(NO or NC) Jumper on the right : NC contact Jumper on the left (factory setting) : NO contact
X17 Relay contact type 2
(NO or NC) Jumper on the right : NC contact Jumper on the left (factory setting) : NO contact
X18 Repeater (RTNet end of line
element) Jumper up (factory setting) : EOL connected Jumper down : do not use
X26 Serial connection (not used) Jumper down (factory setting) : do not change the position
Other elements
F1 / F2 Pluggable fuse 2 AF Fuse for protection of control outputs 4 (F1) and 5 (F2)
F3 Pluggable fuse 1 AT Fuse for protection of 24V output
F4 / F5 / F6 Pluggable fuse 1 AT Fuse for protection of control outputs 1 (F4), 2 (F5) and 3 (F6)
S1 Reset —
S18-1 / S18-2 Not used Do not change (factory setting : OFF)

Overview
17
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
PCB terminal blocks
X1 Plug-in block 6 points
(1.5 mm2max.) 1-2 (–) / 5-6 (+) 24V power supply
3-4 (+) Power supply monitoring
X5 Plug-in block 4 points
(2.5 mm2max.) 1 (+) / 2 (–) Monitored output 5
3 (+) / 4 (–) 24V use output
X6 Plug-in block 4 points
(2.5 mm2max.) 1 (+) / 2 (–) Monitored output 3 (control polarities, reversed in standby)
3 (+) / 4 (–) Monitored output 4
X7 Plug-in block 4 points
(2.5 mm2max.) 1 (+) / 2 (–) Monitored output 1 (control polarities, reversed in standby)
3 (+) / 4 (–) Monitored output 2 (control polarities, reversed in standby)
X9 Plug-in block 8 points
(1.5 mm2max.) 1 (+) / 2 (–) Monitored input 1
3 (+) / 4 (–) Monitored input 2
5 (+) / 6 (–) Monitored input 3
7 (+) / 8 (–) Monitored input 4
X10 Plug-in block 8 points
(1.5 mm2max.) 1 (+) / 2 (–) Fire detectors zone 1
3 (+) / 4 (–) Fire detectors zone 2
5 (+) / 6 (–) Fire detectors zone 3
7 (+) / 8 (–) Extinguishing manual control
X11 Plug-in block 10 points
(1.5 mm2max.) 1 / 2 Potential-free contact relay 1 (NO or NC)
3 / 4 Potential-free contact relay 2 (NO or NC)
5 / 6 Potential-free contact relay 3 (NO or NC)
7 / 8 Potential-free contact relay 4 (NO or NC)
9 / 10 Potential-free contact relay 5 (NO or NC)
X12 Plug-in block 10 points
(1.5 mm2max.) 1 … 8 (–) Logical outputs 1 to 8
9 (–) / 10 (+) Repeater display / Repeater terminal RTNet connection
X21 Jack 2.5 mm — Maintenance PC
X27 Plug-in block 4 points
(1.5 mm2max.) 1 (+) Reset
2 … 4 (+) Unmonitored inputs 2 to 4
X28 Faston 5.3 mm (+) To positive of battery (to provide “Total loss of power supply”
function (see note 1)
X20 (*) Flat cable 26 points — Connection for multi-sector module XCA1030
X35 Terminal 12 points — Connection for 4 digits display
X23, 24 Not used — —
(*) on welding side
Note 1: The XC10 provides the EN54-2 option with requirement 8.4 called “Total loss of power”. This option when selected activates the
system fault LED and the buzzer continuously, for at least 1 hour after a low discharge battery disconnection. The option can be
selected by wiring the +BAT terminal to the positive voltage of batteries (use of remaining power after battery disconnection).

Overview
18
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
4.6 User interface
All display and control elements, except 4-digit display for XC1001-A version, are
accessible to the user:
- Led 1 to 32 indicators for operating condition,
- Keys 1 to 15 allowing :
èoperating access
èoperation (reset, off, test, etc)
èsystem test
èuser functions programming
- 4-digit display showing:
èprogramming steps and options
èpre-discharged warning time count down
èother information’s (calibration states, alarm counter, etc)
Fig. 6 XC100x-A, user interface
Indicators State Description
N° Color
1Green Fixed The control panel is in operation
2Yellow Fixed The control panel is not able to function any more
Fast Fault on at least one component in the system (see paragraph 14.2 for the detail)
Or,
Non-monitorred Control Input 3 is in active state, assuming it is programmed as “External device fault”
(Step50 – Option7)
3Yellow Slow Mains fault
Fast Batteries fault
4Yellow Fixed Microprocessor fault
Slow Jumper buzzer (X3 - XCM1002 board) not connected (remainder)
5Yellow Fast At least one component connected to the control panel is grounded
6Yellow Fixed –At least one component in the system is disabled
–Calibration in progress or error
–Programming in progress
7Yellow Slow At least one detection zone and/or extinguishing manual control is being tested
8Red Fixed At least one detection zone is in alarm
9Red Fixed Remote transmission activated (according to programming)
10 Yellow Fixed Level 2 operating access granted
Slow System test activated
11 Yellow Fixed Mechanical blocking device is in the blocked position
12 Yellow Fast –Mechanical blocking device is in a wrong position
–Selector valve is in a wrong position (used for multi-sector applications)
13 Yellow Fast Loss of agent

Overview
19
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
Indicators State Description
N° Color
14 Yellow Fixed –Manual release is blocked or being tested
15 Yellow Fixed –Standard = not used
–Alternative = automatic and manual release granted (UK)
16 Yellow Fixed –Automatic release is blocked
–At least one detection zone which starts the extinguishing is off or being tested
17 Red Fixed –All detection zones which start the extinguishing are in alarm condition
–One of the electrical manual triggering device (DM1103-L) is actuated
Fast One of the detection zones which start the extinguishing is in alarm condition
18 Red Fixed Extinguishing agent is released
Slow / Fast Discharged contact is not activated within 30 seconds after actuators control (according to programming)
19 Yellow Fixed Sounders are disabled
Slow Sounders test is in progress (real activation)
Fast At least, an output programmed as Sounders is in fault condition (break or short-circuit)
20 Yellow Fixed Actuators are disabled
Slow Actuators test is in progress (simulated activation)
Fast –At least, one output programmed as actuators is in fault condition (break or short-circuit)
–Calibration in progress or error or no calibration data
21 Yellow Fixed Fire controls are disabled
Slow Warning panels test is in progress (real activation)
Fast At least, one output programmed as fire controls is in fault condition (break or short-circuit)
22 Yellow Fixed RT-fault is disabled
Slow RT-fault test is in progress (real activation)
23 Yellow Fixed RT-alarm is disabled
Slow RT-alarm test is in progress (real activation)
Fast At least, one output programmed as RT-alarm is in fault condition (break or short-circuit)
24 Yellow Fixed Emergency abort is activated
Slow Emergency hold is activated (DM1103-S)
Fast At least, one input programmed as emergency hold/abort is in fault condition (break or short-circuit)
25 Red Fixed Detection zone 1 is in alarm condition
Slow Detection zone 1 is in alarm condition (first alarm)
26 Yellow Fixed / Slow Detection zone 1 is disabled (fixed) / being tested (slow)
Fast Detection zone 1 is in fault condition (break or short-circuit)
27 Red Fixed Detection zone 2 is in alarm condition
Slow Detection zone 2 is in alarm condition (first alarm)
28 Yellow Fixed / Slow Detection zone 2 is disabled (fixed) / being tested (slow)
Fast Detection zone 2 is in fault condition (break or short-circuit)
29 Red Fixed Detection zone 3 is in alarm condition
Slow Detection zone 3 is in alarm condition (first alarm)
30 Yellow Fixed / Slow Detection zone 3 is disabled (fixed) / being tested (slow)
Fast Detection zone 3 is in fault condition (break or short-circuit)
31 Red Fixed Manual release is activated (DM1103-L line)
Slow Manual release is activated (DM1103-L line) – First alarm
32 Yellow Fixed / Slow Manual release is disabled (fixed) / being tested (slow)
Fast Manual release is in fault condition (break or short-circuit)

Features
20
Building Technologies A6V10257473_e_en_--
Fire Safety 2015-03-04
Keys Description
1 … 4 Operating access code input (level 2, programming, system test, etc.)
èWhen operating access level 2 is selected, if the code is entered again, the system returns to the level 1, without waiting
for the end of the 4 minutes timeout
5
Silence / Restar
t sounders by successive pressing:
–1st pressing: silence sounders
–2nd pressing: restart sounders etc…
èOperating access level required for this operation = level 2 (silence sounders is not possible during pre-discharged
warning time)
6
Silence buzzer
èOperating access level required for this operation = level 1 or 2 or 2 only (according to programming)
èIf a Repeater Terminal is connected to the XC10, and if option 61 step 02 is selected, silence buzzer on XC10 silences
also buzzer on repeater
7
1)
Reset
of the system. Reset is not possible
:
–during pre-discharged warning time, emergency stop and flooding time
–if buzzer and/or sounders are not silenced
–if manual release button and/or discharged contact are not reset (according to programming)
èOperating access level required for this operation = level 2
2) Fault reset
èOperating access level required for this operation = level 2
8
Mode of operating, by successive pressing:
–1st pressing: automatic blocked
–2nd pressing: automatic and manual blocked
–3rd pressing: normal mode
èOperating access level required for these operations = level 2
9
Led and buzzer test (duration = 6 seconds)
:
All led indicators are activated and the buzzer sounds continuously (during the first three seconds, all the segments of the
display are activated, then the SW version is displayed)
èOperating access level required for this operation = level 1
10
Disable / Enable by successive pressing:
–1st pressing: actuators are disabled
–2nd pressing: sounders and actuators are disabled
–3rd pressing: fire controls are disabled
–4th pressing: all is disabled
–5th pressing: all is enabled
èOperating access level required for these operations = level 2
11
Disable / Enable by successive pressing:
–1st pressing: RT-fault is disabled
–2nd pressing: RT-fault is enabled / RT-alarm is disabled
–3rd pressing: RT-fault and RT-alarm are disabled
–4th pressing: all are enabled
èOperating access level required for these operations = level 2
12
Disable / Enable by successive pressing (not possible in case of fault or
alarm):
–1st pressing: zone 1 is disabled
–2nd pressing: zone 1 is tested
–3rd pressing: zone 1 is in normal condition
èOperating access level required for these operations = level 2
13
Disable / Enable by successive pressing (not possible in case of fault o
r alarm):
–1st pressing: zone 2 is disabled
–2nd pressing: zone 2 is tested
–3rd pressing: zone 2 is in normal condition
èOperating access level required for these operations = level 2
14
Disable / Enable by successive pressing (not possible in case of fault
or alarm):
–1st pressing: zone 3 is disabled
–2nd pressing: zone 3 is tested
–3rd pressing: zone 3 is in normal condition
èOperating access level required for these operations = level 2
15
Disable / Enable by successive pressing (not possible in case of fault
or alarm):
–1st pressing: manual release is disabled
–2nd pressing: manual release is tested
–3rd pressing: manual release is in normal condition
èOperating access level required for these operations = level 2