Siemens CFG3.F200 User manual

Edge Controller F200 - CFG3.F200
Product Data Sheet
Edge Controller F200 for the cloud integration of FIN Framework, FIN Stack
and/or third-party systems.
●2-port Ethernet switch for LAN (includes daisy chaining)
●1-port Ethernet for WAN
●USB interface for 4G dongles
●Operating voltage AC 24 V or DC 24 V
●Mounting on standard rails or on the wall
●Plug-in screw terminal blocks
●Multi-site management
●Remote operation and monitoring
●Alarm treatment
●Remote tool access, update, and configuration via Siemens Cloud Services

2
Functions F200 Edge Controller provides two integration levels for connecting devices to the cloud:
System integration (between the F200 and the devices) and cloud integration (between the
F200 and the cloud).
A broad range of devices can be integrated on the system level. F200 Edge Controller
supports various protocols (BACnet, Modbus) and Ethernet.
The device supports Ethernet and 4G on the cloud level via the MQTT protocol.
The specific set of supported functions may vary according to the region (for example UL
markets) and according to the connected system. Detailed information about the latest
supported functions can be found in the release notes of the installed software.
Application F200 Edge Controller is a physical device where FIN Framework or FIN Stack is running to
monitor and control building/s. Additionally to that, FIN Edge2Cloud is provided for secure
remote access with no requirement for a VPN.
It can also securely transmit data to the cloud over cable networks or over mobile networks
(e.g. 4G: With a router). 4G USB Dongle support is available in addition (see “Accessories”).
Type summary
Type
Order number
Description
CFG3.F200
S55842-Z133
Embedded FIN Framework/FIN
Stack device
Equipment combinations
Accessories
The accessories listed below are tested but not sold by J2 Innovations:
Manufacturer
Type
Description
Siemens
6EP3332-6SB00-0AY0
Power supply DC 24 V / 2.5 A
Verizon
USB730L / MC730
4G USB Dongle
Huawei
E3372 / E3372h - 153
4G USB Dongle
Huawei
E3372 / E3372h - 320
4G USB Dongle
Alcatel
IK40V-2AALDE1
4G USB Dongle
Please confirm compatibility of the chosen 4G Dongle according to the infrastructure of your
regional Internet Service Provider before choosing and ordering a specific device (i.e.
compatibility of regional 4G frequency bands). Consult “4G Dongle Commissioning Guide”
for further instructions and information.

3
Technical and mechanical design
The compact build can be mounted on standard rails or walls.
1
Plastic housing
2
LEDs for communication and status
3
Service button
4 a)
2-port Ethernet switch with 2 LEDs per port
4 b)
1-port Ethernet interface with 2 LEDs for WAN
(Internet access)
5
Plug-in terminal blocks with screw terminals
Power supply
6
USB interface for 4G dongles
7
Not supported (For future release)
8
Not supported (For future release)
9
Slider for mounting on standard mounting rails
10
Eyelets for cable ties
11
Holes for wall mounting
12
Date / Series and Serial number
LED indicators
Activity
LED / Interface
Color
Activity
Function
Ethernet 1...3
Green
Continuously ON
Link active
Continuously OFF
No connection
Flashing
Network traffic
Yellow
Continuously ON
Link 100 Mbps
Continuously OFF
Link 10 Mbps
RUN
Green
Continuously ON
Device operational
Continuously OFF
Device not operational
Flashing
Start-up or program halted
Red
Continuously OFF
OK
Continuously ON
HW or SW fault –power off and on the
F200
Rapid flashing
Firmware or application
missing/corrupted
Blue
Continuously ON
Connection to the cloud OK
Flashing
No connection to the cloud
Onboarding to cloud not finished or
device certificates not updated

4
Notes
Safety
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
Mounting position and ambient temperature
The devices can be snapped onto standard rails or screwed onto a flat surface.
Plug-in screw terminals connect power and interfaces (except for Ethernet).
Ambient temperature -5...50 °C (23...122 °F)
Ambient temperature -5...45 °C (23...113 °F)
●Wall, horizontal
–From left to right
–From right to left
●Overhead
●Wall, vertically
–From top to bottom
–From bottom to top
●On a horizontal surface
CAUTION
Risk of overheating for failure to comply with ambient temperature
Burning and damage to the device
●Ensure sufficient ventilation to comply with the permissible ambient temperature within
the panel or installation box. The temperature must be at least 10 K (18° F) lower
outside the installation box.
Installation
WARNING
Electric shock
Incorrect installation of the device may lead to electric shock injuries when touching the
device!
●Install the device in a lockable cabinet or use terminal covers.
●Do not install the device in locations where children are likely to be present.
●Conductors with a cross-section of 0.5 mm2 (AWG24) or greater shall comply with the
requirements of IEC 60332-1-2 and IEC 60332-1-3 or IEC TS 60695-11-21.

5
Commissioning / service
NOTICE
When using a 4G dongle
Reboot the device after a 4G dongle has been connected.
For details see 4G Dongle Setup (A6V12059208).
Technical data
Power supply
Operating voltage 24 V AC (24 V≃, ⏊, )
AC 24 V -15 / +20 % (SELV / PELV) or
AC 24 V Class 2 (US)
48…63 Hz
Operating voltage 24 V DC
DC 24 V -15 / +20 % (SELV / PELV) or
DC 24 V Class 2 (US)
Functional ground (US)
Functional earth
The terminal for the functional ground must be
connected on the installation side with the building
grounding system (PE).
Screw terminals for wire cross sections up to
Max. 2.5 mm2(14 AWG)
Internal fusing
2.5 A irreversible / non-replaceable
External supply line fusing (EU)
Non-renewable fuse max. 10 A slow
or
circuit breaker max. 13 A
Tripping characteristic B, C, D per EN 60898
or
Power supply with current limitation of max. 10 A
Power consumption (for transformer planning)
Power consumption AC
16 VA
Power consumption DC
8 W
Function data
Hardware information
Processor
NXP i.MX8 DualX
Storage
2 GB RAM
8 GB eMMC
Data backup in the event of power failure
Super cap to support real-time clock (7 days).

6
Interfaces
Ethernet interfaces
Plug
3 x RJ45, shielded
Interface type
10Base-T / 100Base-TX, IEEE 802.3 compatible
Bit rate
10/100 Mbps, autosensing
Protocol
BACnet on UDP/IP, Modbus TCP/IP, KNX IP, Haystack
over RESTful API, OPC UA, oBix, Sedona, and SQL.
Cabling, cable type
10 Mbps: Min. CAT3, shielded cable is recommended
100 Mbps: Min. CAT5, shielded cable is recommended
Cable length
Max. 100 m (330 ft)
Screw terminals, plug-in
Cu-wire or Cu-strand with wire end sleeve
1 x 0.6 mm ∅to 2.5 mm2(22 to 14 AWG)
or 2 x 0.6 mm ∅to 1.0 mm2(22 to 18 AWG)
Cu-strand without wire end sleeve
1 x 0.6 mm ∅to 2.5 mm2(22 to 14 AWG)
or 2 x 0.6 mm ∅to 1.5 mm2(22 to 16 AWG)
Stripping length
6...7.5 mm (0.24...0.29 in)
Screwdriver
Slot screws, screwdriver size 1 with shaft ø = 3 mm
Max. tightening torque
0.6 Nm (0.44 lb ft)
USB interface (4G internet connection)
Plug
Type A
Interface type
USB 2.0
Bit rate
480 Mbit
Max. load
500 mA
Max. cable length
5 m
Conformity
Ambient conditions and protection classification
Classification as per EN 60730
Automatic action
Control function
Degree of pollution
Overvoltage category
Type 1
Class A
2
III
Design
Suitable for use in protection class I or II systems

7
Ambient conditions and protection classification
Degree of protection of housing to EN 60529
Front parts in DIN cut-out
Terminal part
IP30
IP20
Climatic ambient conditions
●Storage / Transport (packaged for transport) as per
IEC EN 60721-3-1 / IEC EN 60721-3-2
●Operation as per IEC/EN 60721-3-3
●Class 1K22 / 2K12
Temperature -25...70 °C (-13...158 °F)
Air humidity 5...95 % (non-condensing)
●Class 3K23
Temperature -5...50 °C (23...122 °F)
(for details see chapter Mounting)
Air humidity 5...95 % (non-condensing)
Mechanical ambient conditions
●Transport per IEC/EN 60721-3-2
●Operation as per IEC/EN 60721-3-3
●Class 2M4
●Class 3M11
Standards, directives and approvals
Product standards
EN 60730-1 and EN 62368-1
Product family standard
EN 50491-x
Electromagnetic compatibility (EMC)
For residential, commercial, and
industrial environments
EU conformity (CE)
See CE declaration 1)
UL/cUL approbation (US / Canada)
UL916; http://ul.com/database
CSA certification
C22.2, http://csagroup.org/services-industries/product-
listing
Environmental compatibility 1)
The product environmental declaration1) contains data
on environmentally compatible product design and
assessments (RoHS compliance, materials
composition, packaging, environmental benefit,
disposal).
1) Documents can be downloaded at http://siemens.com/bt/download.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
●Consult the dealer or an experienced radio/TV technician for help.

8
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation
FCC Caution: Changes or modifications not expressly approved by Siemens Switzerland
Ltd. could void user authority to operate the equipment. United States representative
https://new.siemens.com/us/en/products/buildingtechnologies/home.html
Housing
Housing
Color top/bottom
RAL 7035 (light grey) / RAL 7016 (anthracite grey)
Dimensions
per DIN 43 880, see dimensions
Weight with/without packaging
350 g / 300 g
Connection terminals
Terminal
Symbol
Description
1A, 1B
2 x RJ45 interface for Ethernet with switch
LAN (customer network)
2
1 x RJ45 interface for Ethernet
WAN (internet access)
5, 6
≃, ⏊,
Operating voltage AC 24 V, DC 24 V
7
Functional ground (must be connected on the installation side with the building
grounding system (PE).
USB
USB interface for 4G dongles
Dimensions All dimensions in millimeters and inches.
65 66 67 68 69 70
5
AC/DC 24VWANLAN 1B1A 2
6 7

9
Disclaimer Please see this link for more information about OSS for the CFG3.F200.
124 (4.88")
117 (4.61")
110 (4.33")
129 (5.08")
4.1(0.16")
144 (5.67")
26.5 (1.04")
45 (1.77")
69.5 (2.73")
74.5 (2.93")
4 (0.16")
21.5 (0.85")
11 (0.43")
45 (1.77") 21.5 (0.85")
11 (0.43")
35.5 (1.40")
49 (1.91")

.