Siemens Desigo PXC4.E16 User manual

A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Desigo™
Automation station
PXC4.E16
For the control of primary plants
●Compact automation station for HVAC and building control systems,
freely programmable using graphical programming interface
●Communication BACnet/IP
●2-port Ethernet switch for low-cost cabling
●16 inputs/outputs: 12 universal inputs/outputs, 4 relay outputs
Extendable to 40 inputs/outputs via I/O modules TXM…
●Integration of Modbus data points via RTU and / or TCP
●WLAN interface for engineering and commissioning
●Operating voltage AC 24 V
●Mounted on standard rails or on the wall
●Plug-in screw terminal blocks

2
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Functions
Automation station for HVAC and building control systems.
●System functions (alarming, scheduling, trending, access protection with individually
definable user profiles and categories)
●Freely programmable (close resemblance to CEN standard 11312). All function blocks,
available in libraries, can be graphically connected.
●Engineering and commissioning with the ABT Site Tool using graphical function charts
●BACnet communication, in compliance with the BACnet standard including B-BC profile
(Rev. 1.15)
●Generic object viewer for device local data points via an embedded web-based interface
●Wireless connection for engineering and commissioning
●Cloud connectivity for remote access
●Integration of Modbus data points via RTU and/or TCP
●Direct connection of field devices
Type summary
Type
Order number
Description
PXC4.E16
S55375-C100
Compact automation station for BACnet/IP
Inputs/outputs
Total number of inputs/outputs (Onboard)
16
Number of universal inputs/outputs (UIO)
12
Number of relay outputs (DO)
4
Number of inputs/outputs (Onboard + TXM)
40
Number of Modbus data points TCP and/or RTU
40
UIO
Universal inputs/outputs support the following signal types:
●Passive sensors LG-Ni 1000, 2x LG-Ni1000, Pt 1000 (*75, 385), NTC 10k, NTC 100k
●Resistance sensors 1000 Ohm, 2500 Ohm, 2650 Ohm, 1000...1175 Ohm (for setpoint shift)
●Active sensors DC 0 ... 10 V
●Current measurement analog DC 0...20 mA or 4...20 mA, (inputs U1, U2, U7, U8)
●Binary potential-free contacts for signaling functions
●Counter to 25 Hz (electronic switch to 100 Hz)
●Analog outputs DC 0…10 V
DO
Relay outputs for binary controls, changeover contact
(NO, NC, pulse)
Equipment combinations
I/O modules TXM (Series D and later)
Description
Type
Data sheet
Digital input module 8 or 16 I/O points
TXM1.8D, TXM1.16D
CM2N8172
Universal module without / with local operation and LCD
TXM1.8U, TXM1.8U-ML
CM2N8173
Super universal module without / with local operation and LCD
TXM1.8X, TXM1.8X-ML
CM2N8174
Relay module without / with local operation
TXM1.6R, TXM1.6R-M
CM2N8175
Resistance measuring module (for Pt100 4-wire)
TXM1.8P
CM2N8176
Triac module
TXM1.8T
CM2N8179
Digital input and relay module
TXM1.4D3R
CM2N8188

3
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
PXC4 can power TXM extensions modules (for details see planning overview A6V11973797)
Desigo Control Point
Description
Type
Data sheet
BACnet touch panels with integrated Web server
7.0 "
10.1 "
15.6 "
PXM30.E
PXM40.E
PXM50.E
A6V11664137
Client Touch Panels with data storage in Web server PXG3.Wx00-1:
7.0 "
10.1 "
15.6 "
PXM30-1
PXM40-1
PXM50-1
A6V11664139
BACnet/IP Web server with standard functionality
BACnet/IP Web server with extended functionality
PXG3.W100-1
PXG3.W200-1
A6V10808336
System controller
Description
Type
Data sheet
System controller to integrate Modbus and MS/TP devices
PXC5.E003
A6V11646020
Technical and mechanical design
The compact build allows for mounting the devices on a standard rail or a wall.
45 6
15 1413
10 12
1
3
2
7
9
8
11
16
Date/Series
S/N
WLAN
Default
4
2-port Ethernet switch with 2 LEDs per port for
display purposes
5
Plug-in terminal block with screw terminals
KNX, PL-link, for future use
6
Plug-in terminal block with screw terminals
Power supply
7
Plug-in terminal blocks with screw terminals
Universal inputs/outputs, field device supply
8
Connector for I/O modules TXM
9
Plug-in terminal block with screw terminals
Relay outputs
10
Plug-in terminal block with screw terminals
COM, Modbus RTU
11
DIP switch for bus termination and polarization
COM
12
Slider for mounting on DIN rails
13
Eyelets for cable ties
1
Plastic housing
14
Holes for wall mounting
2
Service button (identification in the network and
WLAN on/off)
15
Date / Series and Serial number
3
LEDs for communication and state
16
QR code for default WLAN access
Description see Technical data
LED displays
Activity
LED
Color
Activity
Function
Ethernet
1/2
Green
Continuously ON
Continuously OFF
Flashing
Link active
No connection
Network traffic
Yellow
Continuously ON
Continuously OFF
Link 100
Link 10 Mbps
RUN
Green
Continuously ON
Device operational

4
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Activity
LED
Color
Activity
Function
Continuously OFF
Flashing
Device not operational
Start-up or program halted
Red
Continuously OFF
Continuously ON
Rapid flashing
OK
HW or SW fault
Firmware or application missing/corrupted
Blue
Continuously ON
Continuously OFF
Connection to the cloud OK
No connection to the cloud
COM TX
Yellow
Flashing
Continuously OFF
Communication
No communication to subsystem
COM RX
Yellow
SVC
Red
Continuously OFF
Flashing
OK
Device is not configured
Flashing per wink
command
Identification of the device after receipt of wink
command
2s 1s
5 Hz 5 Hz
2s 1s
WLAN
Blue
Steady OFF
Steady ON
Flashing
WLAN inactive
WLAN active and at least one WLAN client
connected
WLAN active and no WLAN client connected
Service
button
Short press (< 1 s)
Long press (> 3 s)
Identification in the network
Enable / disable WLAN
WLAN is disabled automatically after 10 min if
no client is connected
As per description
Do the following to reset the device to factory
state:
1. Power off the device.
2. Power on the device.
3. Wait until all LEDs light up and turn off
again, then press the Service button.
4. Keep the Service button pressed until all
LEDs light up, then release the button.
All LEDs go off, the device restarts.
5. Wait until the device has fully started –
unconfigured (green RUN LED and red
SVC LED are flashing)
Product documentation
Related documents such as the environmental declarations, CE declarations, etc., can be
downloaded from the following Internet address:
https://siemens.com/bt/download

5
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Notes
Safety
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and
property damage.
●Observe national provisions and comply with the appropriate safety regulations.
●This equipment is intended only for use in a restricted access area (lockable cabinet)
●This equipment is not suitable for use in locations where children are likely to be
present.
●Conductors with a cross-section of 0.5 mm2 (AWG24) or greater shall comply with the
requirements of IEC 60332-1-2 and IEC 60332-1-3 or IEC TS 60695-11-21.
Mounting position and ambient temperature
The devices can be snapped onto standard rails or screwed onto a flat surface.
Plug-in screw terminals connect power and interfaces.
Ambient temperature -5...50 °C (23...122 °F)
Ambient temperature -5...45 °C (23...113 °F)
●Wall, horizontal
–From left to right
–From right to left
●Overhead
●Wall, vertically
–From top to bottom
–From bottom to top
●On a horizontal surface
CAUTION
Risk of overheating for failure to comply with ambient temperature
Burning and damage to the device
●Ensure sufficient ventilation to comply with the permissible ambient temperature within
the panel or installation box. The temperature must be at least 10 K (18° F) lower
outside the installation box.
Installation
WARNING
No internal line protection for supply lines to external consumers
Risk of fire and injury due to short-circuits!
●Adapt the wire cross sections as per local regulations to the rated value of the installed
fuse.
WARNING
The relay outputs may be connected to mains voltage
Risk of electrical shock!
●Use terminal covers or install the device in a lockable cabinet.

6
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Disposal
The device is considered an electronic device for disposal in accordance
with the European Guidelines and may not be disposed of as domestic
garbage.
●Dispose of the device through channels provided for this purpose.
●Comply with all local and currently applicable laws and regulations.
Technical data
Power supply
Operating voltage (24 V~, ⏊, )
AC 24 V -15 / +20 % (SELV / PELV) or
AC 24 V Class 2 (US)
48…63 Hz
Functional ground (US)
Functional earth
The terminal for the functional ground must be
connected on the installation side with the building
grounding system (PE).
Screw terminals for wire cross sections up to
Max. 2.5 mm2(14 AWG)
Internal fusing
4 A irreversible / non-replaceable
External supply line fusing (EU)
Non-renewable fuse max. 10 A slow-blow
or
circuit breaker max. 13 A
Tripping characteristic B, C, D per EN 60898
or
Power supply with current limitation of max. 10 A
Power consumption (for transformer planning)
Base load (without loading by I/O modules TXM and
field devices)
10 VA / 0.4 A
Field device supply V+ (DC 24 V, 100 mA)
(terminals 8 and 19)
5 VA / 0.2 A
Field device supply V~ (AC 24 V, 2 A)
(terminals 18 and 29)
48 VA / 2 A
I/O modules TXM supply
15 VA / 0.6 A
Function data
Hardware information
Processor
Texas Instruments AM335x, 300 MHz
Storage
128 MByte SDRAM (DDR3)
512 MByte NAND Flash
Data backup in the event of power failure
Energy reserve (supercap) to support real-time clock (7 days).
Data available if stored to flash memory. Occurs every 5 minutes.

7
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Interfaces
Screw terminals, plug-in
Cu-wire or Cu-strand with wire end sleeve
1 x 0.6 mm ∅to 2.5 mm2(22 to 14 AWG)
or 2 x 0.6 mm ∅to 1.0 mm2(22 to 18 AWG)
Cu-strand without wire end sleeve
1 x 0.6 mm ∅to 2.5 mm2(22 to 14 AWG)
or 2 x 0.6 mm ∅to 1.5 mm2(22 to 16 AWG)
Stripping length
6...7.5 mm (0.24...0.29 in)
Screwdriver
Slot screws, screwdriver size 1
Max. tightening torque
0.6 Nm (0.44 lb ft)
Ethernet interface
Plug
2 x RJ45, shielded
Interface type
10Base-T / 100Base-TX, IEEE 802.3 compatible
Bit rate
10/100 Mbps, autosensing
Protocol
BACnet on UDP/IP and HTTPS on TCP/IP
Cabling (in-house cabling only), cable type
10 Mbps: Min. CAT3, shielded cable is recommended
100 Mbps: Min. CAT5, shielded cable is recommended
Cable length
Max. 100 m (330 ft)
Modbus RTU interface
Interface type
EIA-485, electrically isolated
Baud rate
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
(depending on the configuration)
Internal bus termination
120 Ohm, switchable with DIP switch
Internal bus polarization
270 Ohm pull-up/pull-down resistances, switchable with
DIP switch
Cabling (in-house cabling only)
Cable length
3-wire cable
Max. 1000 m (3300 ft)
Protection
Short-circuit proof
Protection against faulty wiring with AC 24 V
WLAN interface
Interface type
Wireless access point
Supported standards
Frequency band
WLAN channels
Maximum radio-frequency power
IEEE 802.11b/g/n
2.4…2.462 GHz
1…11
16.4 dBm
Distance (unobstructed field)
Min. 5 m (16 ft)
Device pairing
Activation / Deactivation with service button
Automatic switch off after 10 minutes if no WLAN-client
is connected.
Optionally, for cyber security reasons, the WLAN can be
permanently disabled via configuration.
Default SSID and WLAN password: Scan the QR code.
It will show something like WIFI:S:PXC4.E16_0000550;T:WPA;P:1400052738;;
Then SSID = PXC4.E16_0000550 and password = 1400052738
Determine manually: Use the information from the Date/Series/SN block It will show something like:
Date/Series: 20190423A0000550
S/N: 1400052738
SSID = <ASN>_<Running number after the series letter> and password = <S/N>
I/O modules TXM interface
Nominal voltage
DC 24 V
Power supply for I/O modules TXM
Max. 300 mA

8
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
I/O modules TXM interface
Parallel switchable with 24VDC Supply TXS1.12F4
For details, see: TX-I/O engineering and installation,
CM110562
Protection
Short-circuit proof
Connector for I/O modules TXM on the side: No
protection against faulty wiring with AC 24 V
No electrical protection.
Use the cover
Inputs
12 universal inputs U1...U12 with the following functions
Temperature measurement, analog
Type
Range (over range)
Resolution
AI NTC10K
-40...115 °C (-52.5...155 °C)
-48...239 °F (-62.5...311 °F)
10 mK (25 °C)
0.018 °F
AI NTC100K
-40...125 °C (-52.5...155 °C)
-48...257 °F (-62.5...311 °F)
AI PT1K 385 (EU) *)
-50...600 °C (-52.5...610 °C)
-58...1112 °F (-62.5...1130 °F)
20 mK
0.036 °F
AI PT1K 375 (NA) *)
-50...180 °C (-52.5...185 °C)
-58...356 °F (-62.5...365 °F)
10 mK
0.018 °F
AI (LG-)Ni1000 *)
AI 2x (LG-)Ni1000 *)
Resistance sensor, analog
Type
Range (over range)
Resolution
AI 1000 Ohm *)
0...1000 Ω (0...1050 Ω)
0.1 Ω
AI 2500 Ohm *)
0...2500 Ω (0...2650 Ω)
0.1 Ω
AI Pt1000 *)
0...2500 Ω (0...2650 Ω)
0.1 Ω
AI 1000-1175 Ohm *) for setpoint shift
1000...1175 Ω (900...1295 Ω)
0.1 Ω
*) A fixed value of 1 Ω is calibrated to correct line resistance.
Voltage measurement, analog
Type
Range (over range)
Resolution
AI 0...10 V
0...10 V (-1.5...11.5 V)
1 mV
AI 0...10 V standard
0...100% (-10...110%)
0.01%
Open connection: Negative voltage -1.5 V (line failure detection)
Current measurement, analog (only inputs U1, U2, U7, U8)
Type
Range (over range)
Resolution
Load
AI 4-20 mA
4...20 mA (1.6...22.4 mA)
1 µA
Min. 490 Ω
AI 0-20 mA
0...20 mA (-3...23 mA)
1 µA
Min. 490 Ω
Digital input
Contact query voltage
21.5...25 V
Contact query current
1 mA; 6 mA initial current
Contact resistance for closed contacts
Max. 200 Ω
Contact resistance for open contacts
Min. 50 kΩ
Counter memory (counter inputs
0 ... 4.3 x 109(32-bit counter)
Min. closing/operating time [ms]
including bounces
Of which
Max. bounce time [ms]
Max. counter frequency
(symmetrical)
BI NO / BI NC
60
20

9
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Digital input
BI Pulse NO
30
10
CI Mech (25Hz)
20
10
25 Hz
CI El (100Hz)
5
0
100 Hz
Outputs
Analog output
Type
Range (over range)
Resolution
Output current
AO 0-10 V
0...10 V (-0.05…10.6 V)
1 mV
Max. 1 mA
AO 0-10 V
standard
0...100%
0% = 0 V, 100% = 10 V
(-0.05...10.6 V)
0.01 %
Max. 1 mA
Relay output (outputs DO1...DO4)
External supply line fusing
Non-renewable fuse
Circuit breakers
Max. 10 A, slow
Max. 13 A, characteristic B, C, D as per EN 60898
Switching voltage AC/DC
Max. AC 250 V / DC 30 V
Min. AC/DC 12 V
Current load AC
NO contact: Max. 4 A resistive, 3 A inductive (cos phi
0.6)
NC contact: max. 2 A resistive, 1.5 A inductive (cos phi
0,6)
Min. 1 mA at AC 250 V
Min. 10 mA at AC 12 V
Current load DC
NO contact: Max. 3 A resistive at DC 30 V
NC contact: Max. 1 A resistive at DC 30 V
Min. 10 mA resistive at DC 12 V
Switch-on current
NO contact: Max. 10 A (1 s)
NC contact: Max. 3 A (1 s)
Response/release time
7 ms / 3 ms typical
Contact life at AC 250 V (reference values)
At 0.3 A resistive
NO contact at 3 A resistive
NC contact at 2 A resistive
Reduction fact at ind. load (cos phi = 0.6)
5 x 105switchings
1 x 105switchings
1 x 105switchings
0.6
Insulating strength between relay contacts and system
electronics (reinforced insulation).
AC 3750 V, as per EN 60730-1
Field device supply (Onboard)
AC 24 V (terminal V~)
Max. 2 A, short-circuit proof *)
DC 24 V (terminal V+)
Max. 100 mA, short-circuit proof, protected against
incorrect wiring with AC 24 V
Field device supply (I/O modules TXM)
AC 24 V (terminal V~ on the I/O modules TXM)
Max. 2 A, short-circuit proof *)
*) Sum total onboard V~ and TXM bus V~ max. 2 A

10
Siemens Schweiz AG
A6V11646018_en--_b
Smart Infrastructure
2020-07-10
Conformity
Ambient conditions and protection classification
Classification as per EN 60730
Automatic action
Control function
Degree of pollution
Overvoltage category
Type 1
Class A
2
III
Design
Suitable for use in protection class I or II systems
Degree of protection of housing to EN 60529
Front parts in DIN cut-out
Terminal part
IP30
IP20
Climatic ambient conditions
●Storage / Transport (packaged for transport) as per
IEC EN 60721-3-2
●Operation as per IEC/EN 60721-3-3
●Class 1K22 / 2K21
Temperature -25...70 °C (-13...158 °F)
Air humidity 5...95 % (non-condensing)
●Class 3K22
Temperature -5...50 °C (23...122 °F)
(for details see chapter Mounting)
Air humidity 5...95 % (non-condensing)
Mechanical ambient conditions
●Transport per IEC/EN 60721-3-2
●Operation as per IEC/EN 60721-3-3
●Class 2M11
●Class 3M11
Standards, directives and approvals
Product standard
EN 60730-1
Product family standard
EN 50491-x
Electromagnetic compatibility (EMC)
For residential, commercial, and
industrial environments
EU conformity (CE)
See CE declaration 1)
EAC compliance
Eurasian compliance
RCM conformity
See RCM declaration 1)
UL/cUL approbation (US / Canada)
UL916; http://ul.com/database
CSA certification
C22.2, http://csagroup.org/services-industries/product-
listing
FCC
CFR 47 Part 15 Class B
BACnet.
B-BC
Environmental compatibility 1)
The product environmental declaration 1) contains data
on environmentally compatible product design and
assessments (RoHS compliance, materials
composition, packaging, environmental benefit,
disposal).
1) Documents can be downloaded at http://siemens.com/bt/download.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.