Siemens SITRANS P500 Administrator guide

SITRANS
Pressure transmitter
SITRANS P500 with HART
Edition 04/2013
Compact Operating Instructions
Answers for industry.

1
English ··································································································· 3
Dansk··································································································· 33
Ελληνικά ······························································································ 63
Português····························································································· 95
Svenska ····························································································· 126
Magyar······························································································· 155

© Siemens AG 2013. All rights reserved
A5E02307341-03, 04/2013 3
SITRANS
Pressure transmitter
SITRANS P500 with HART
Compact Operating Instructions
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The
notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage
have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of
injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with
the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their
training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products
and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,
installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.
1 Introduction
1.1 Purpose of this documentation
These instructions are a brief summary of important features, functions and safety information, and contain all information
required for safe use of the device. It is your responsibility to read the instructions carefully prior to installation and
commissioning. In order to use the device correctly, first review its principle of operation.
The instructions are aimed at persons who mechanically assemble the device, connect it electrically, and start it up.
To achieve optimum usage of the device, read the detailed version of the manual.
See also
Instructions and manuals (http://www.siemens.com/processinstrumentation/documentation)

SITRANS P500 with HART
4 A5E02307341-03, 04/2013
1.2 History
This history establishes the correlation between the current documentation and the valid firmware of the device.
The documentation for this revision is applicable for the following firmware:
Revision Firmware and hardware
identity nameplate
System integration Installation path for
PDM
Note
02
09/2010
FW: 35.01.00
HW: 11.01.01
PDM 6.01); Dev. Rev.3
DD; 01.00.00 Dev.
Rev.1
SITRANS P500
03
04/2013
FW: 35.02.00
HW: 11.01.01
PDM 6.01); Dev. Rev.3
DD; 01.00.00 Dev.
Rev.1
SITRANS P500
1) to SP05
1.3 Purpose
Overview
Depending on the variant, the pressure transmitter measures corrosive, non-corrosive and hazardous gases, vapors and
liquids.
With appropriate configuration, you can also use the differential pressure transmitter for the following measurement types:
● Level
● Volume
● Mass
● Volume flow
● Mass flow rate
The output signal is always a load-independent direct current between 4 and 20 mA upon which a HART protocol is
superimposed.
You can install the "Intrinsically safe" or "Flameproof enclosure" version of the transmitter in hazardous areas. The devices
have an EC type-examination certificate and meet the regulations applicable to them, for example, the harmonized
CENELEC standards in Europe.
Transmitters with remote seals of different shapes can be delivered for special applications. For example, measuring high-
viscosity substances is a special application.
Operate the device in accordance with the specifications in section Technical data (Page 27).
For additional information, please refer to the operating instructions for the device.
1.4 Checking the consignment
1. Check the packaging and the device for visible damage caused by inappropriate handling during shipping.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for correctness and completeness.

SITRANS P500 with HART
A5E02307341-03, 04/2013 5
WARNING
Using a damaged or incomplete device
Danger of explosion in hazardous areas.
● Do not use damaged or incomplete devices.
1.5 Nameplate layout
Nameplate with general information
The nameplate with the order number and other important data, such as the design details and technical data can be found
on the side of the enclosure.
① Order number
② Serial number
twistlock screw
Schutzart IP 66/68
Rated pressure : PN 160
Measuring span : 31.25 - 6250 mbar
1. 4404 1. 4404 FKM (FPM) Silicone oil
Mat.: Connec. Diaphr. O-ring Filling
V : DC 10.6-44 V (non IS) 4-20 mA HART
H
F.-Nr. B1-F908-9000001
7MF5603-1DA00-0AD1-Z +E00
Transmitter for differential pressure
0045
PED/SEP
HW: 01.01.00 / FW: 35.00.10
made in France
D-76181 Karlsruhe
SIEMENS AG
SITRANS P500



):FKDQJHFRXQWHU
):IXQFWLRQH[SDQVLRQFRXQWHU
'HYLFHPDUNLQJ
+:FKDQJHVDIIHFWLQJPHFKDQLFDOV\VWHP
+:FKDQJHVDIIHFWLQJHOHFWURQLFV
&RPSDWLELOLW\FRXQWHU
'HYLFHPDUNLQJ
+:DDEEFF ):DDEEFF
Example of a nameplate
③ Firmware (FW) and
hardware (HW)
numbers

SITRANS P500 with HART
6 A5E02307341-03, 04/2013
Nameplate with approval information
The nameplate with approval information is on the opposite side. For the Ex-version of the transmitter, the information on the
respective certificate is also listed.
twistlock screw
II 1/2 G Ex d ia IIC T4/T6
Temperature class T4
T : -40...+85°C (-40...+185°F)
a
U=45V
Observe EC-Type Examination Certificate !
BVS09ATEXE027
T : -40...+60°C (-40...+140°F)
a
Temperature class T6
D-76181 Karlsruhe
SIEMENS AG
SITRANS P500
,,*([GLD,,&77
D E F G

Figure 1-1 Example of a nameplate
① Characteristics of the hazardous area
①a Category of the operating range
①b Type of protection
①c Group (gas, dust)
①d Maximum surface temperature (temperature class)
1.6 Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
● Keep the original packaging for subsequent transportation.
● Devices/replacement parts should be returned in their original packaging.
● If the original packaging is no longer available, ensure that all shipments are properly packaged to provide sufficient
protection during transport. Siemens cannot assume liability for any costs associated with transportation damages.
CAUTION
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
● Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in "Technical data" (Page 27).
1.7 Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement, commitment or legal
relationship. The sales contract contains all obligations on the part of Siemens as well as the complete and solely applicable
warranty conditions. Any statements regarding device versions described in the manual do not create new warranties or
modify the existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right to make technical changes in
the course of further development.

SITRANS P500 with HART
A5E02307341-03, 04/2013 7
2 Safety information
2.1 Precondition for use
This device left the factory in good working condition. In order to maintain this status and to ensure safe operation of the
device, observe these instructions and all the specifications relevant to safety.
Observe the information and symbols on the device. Do not remove any information or symbols from the device. Always
keep the information and symbols in a completely legible state.
Symbol Explanation
Consult operating instructions
2.1.1 Laws and directives
Observe the test certification, provisions and laws applicable in your country during connection, assembly and operation.
These include, for example:
● National Electrical Code (NEC - NFPA 70) (USA)
● Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
● IEC 60079-14 (international)
● EN 60079-14 (EC)
2.1.2 Conformity with European directives
The CE mark on the device is a sign of conformity with the following European directives:
Electromagnetic Compatibility EMC
2004/108/EC
Directive of the European Parliament and of the Council on the approximation of the
laws of the Member States relating to electromagnetic compatibility and repealing
Directive 89/336/EEC.
Atmosphère explosible ATEX
94/9/EC
Directive of the European Parliament and the Council on the approximation of the
laws of the Member States concerning equipment and protective systems intended
for use in potentially explosive atmospheres.
Pressure Equipment Directive PED
97/23/EC
Directive of the European Parliament and of the Council on the approximation of the
laws of the Member States concerning pressure equipment.
The standards applied can be found in the EC declaration of conformity for the device.
2.2 Improper device modifications
WARNING
Improper device modifications
Danger to personnel, system and environment can result from modifications to the device, particularly in hazardous areas.
● Only carry out modifications that are described in the instructions for the device. Failure to observe this requirement
cancels the manufacturer's warranty and the product approvals.
2.3 Requirements for special applications
Due to the large number of possible applications, each detail of the described device versions for each possible scenario
during commissioning, operation, maintenance or operation in systems cannot be considered in the instructions. If you need
additional information not covered by these instructions, contact your local Siemens office or company representative.

SITRANS P500 with HART
8 A5E02307341-03, 04/2013
Note
Operation under special ambient conditions
We highly recommend that you contact your Siemens representative or our application department before you operate the
device under special ambient conditions as can be encountered in nuclear power plants or when the device is used for
research and development purposes.
2.4 Use in hazardous areas
Qualified personnel for hazardous area applications
Persons who install, assemble, commission, operate and service the device in a hazardous area must have the following
specific qualifications:
● They are authorized, trained or instructed in operating and maintaining devices and systems according to the safety
regulations for electrical circuits, high pressures, aggressive and hazardous media.
● They are authorized, trained, or instructed in carrying out work on electrical circuits for hazardous systems.
● They are trained or instructed in maintenance and use of appropriate safety equipment according to the pertinent safety
regulations.
WARNING
Unsuitable device for the hazardous area
Danger of explosion.
● Only use equipment that is approved for use in the intended hazardous area and labelled accordingly.
See also
Technical data (Page 27)
WARNING
Loss of safety of device with type of protection "Intrinsic safety Ex i"
If the device has already been operated in non-intrinsically safe circuits or the electrical specifications have not been
observed, the safety of the device is no longer ensured for use in hazardous areas. There is a danger of explosion.
● Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe circuit.
● Observe the specifications for the electrical data on the certificate and in Chapter "Technical data (Page 27)".
WARNING
Use of incorrect device parts in potentially explosive environments
Devices and their associated device parts are either approved for different types of protection or they do not have
explosion protection. There is a danger of explosion if device parts (such as covers) are used for devices with explosion
protection that are not expressly suited for this type of protection. If you do not adhere to these guidelines, the test
certificates and the manufacturer warranty will become null and void.
● Use only device parts that have been approved for the respective type of protection in the potentially explosive
environment. Covers that are not suited for the "explosion-proof" type of protection are identified as such by a notice
label attached to the inside of the cover with "Not Ex d Not SIL".
● Do not swap device parts unless the manufacturer specifically ensures compatibility of these parts.
WARNING
Risk of explosion due to electrostatic charge
To prevent the build-up of an electrostatic charge in a hazardous area, the key cover must be closed during operation and
the screws tightened.
The key cover may be opened temporarily at any time for the purposes of operating the transmitter, even during plant
operation; the screws should then be tightened again.