Siemens Veeder-Root Driver User manual

Installation Instructions
Document No. 565-714
October 31, 2009
Veeder-Root Driver for PXC Modular
These installation instructions cover the connection of
the Veeder-Root Driver or the Veeder-Root Enterprise
Driver to the Veeder-Root system only. For hardware
installation of the PXC Modular, see PXC Modular
Series Installation and Quick Start (553-638).
Product Description
The Veeder-Root Driver enables communication
between the APOGEE®Automation System and the
Veeder-Root system.
Product Numbers
PXC00-PE96.A PXC Modular RS-485 or
Ethernet ALN, 96 FLN nodes
PXC00-E96.A PXC Modular with BACnet/IP
ALN and BACnet MS/TP ALN,
96 FLN nodes
PXC100-PE96.A PXC Modular RS-485 or
Ethernet ALN, TX-I/O Support,
96 FLN nodes
PXC100-E96.A PXC Modular BACnet/IP ALN
and BACnet MS/TP ALN, TX-I/O
Support, 96 FLN nodes
PXX-485.3 Expansion Module, three
RS-485 FLN connections
LSM-INT-VR Veeder-Root PXC Modular
Driver License
LSM-INT-VRE Veeder-Root Enterprise PXC
ModularDriverLicense
Accessories
538-670 Trunk Interface II, 115V
538-675 Trunk Interface II, 230V
Warning/Caution Notations
WARNING:
Personal injury/loss of life may occur if you
do not follow the procedures as specified.
CAUTION:
Equipment damage or loss of data may
occur if you do not follow the procedures
as specified.
Expected Installation Times
The expected installation time is 30 minutes.
Required Tools and Materials
• Flat-blade screwdriver (1/8-inch blade width).
• Wire strippers.
• Cabling and connectors. See the Connecting
the Veeder-Root Driver to the Veeder-Root
Devicessection.
CAUTION:
Always wear an electro-static discharge
wrist strap and discharge accumulated
static before touching field panel
components.
Prerequisites
• Driver hardware is installed according to its
respective installation instructions.
• FLN Termination blocks installed, if any.
Depending on the type of installation, other
prerequisites may have to be completed.
Item Number: 565-714, Rev. AA Page 1 of 4

Document No. 565-714
Installation Instructions
October 31, 2009
Connecting the Veeder-Root Driver
to the Veeder-Root Devices
Follow these steps to connect the Veeder-Root Driver
to the Veeder-Root system:
1. Make cables per diagram in Figure 1.
2. Connect cables per diagram in Figure 1.
Page 2 of 4 Siemens Industry, Inc.

Document No. 565-714
Installation Instructions
October 31, 2009
2
3
7
2
3
7
RS-485 TRUNK CABLE
(MAX 4000 ft / 1200 m;
STANDARD 24 AWG LOW CAPACITANCE)
TRUNK INTERFACE II
VEEDER-ROOT
TLS CONTROLLER
TAPE BACK
SHIELD
RS-232 25-PIN MALE TO
25-PIN MALE CABLE
(MAX 50 ft)
RS-232 PORT
(25-PIN FEMALE)
RS-232 PORT
(25-PIN FEMALE)
S
-
+
FLN
S
-
+
GROUND WIRE TO EARTH
(P/N 538-583)
POWER PACK
POWER
DRIVER
GW0768R3
Figure 1. Connecting the Veeder-Root Driver to the Veeder-Root Devices.
Siemens Industry, Inc. Page 3 of 4

Document No. 565-714
Installation Instructions
October 31, 2009
Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as
design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners.
© 2009 Siemens Industry, Inc.
Siemens Industry, Inc. Your feedback is important to us. If you have Document No. 565-714
1000 Deerfield Parkway comments about this document, send them to Country of Origin: US
Buffalo Grove, IL 60089-4513 SBT_technical.editor[email protected]. Page 4 of 4
U.S.A.