Siemens 30 64 581 B5310 Operating and maintenance instructions

© Siemens AG
The reproduction, transmission or use
of this document or its contents is not
permitted without express written
authority. Offenders will be liable for
damages. All rights, including rights
created by patent grant or registration
of a utility model or design, are
reserved.
Print No.:
Arnold
Monitor 44cm, 100/120HZ
Monitor 44cm, 100/120HZ
Maintenance Instructions
SP
1998
SPR2-230.101.01.02.02
Replaces: SPR2-230.101.01.01.02
English
Doc. Gen. Date: 08.05
Monitor 44 cm, 100/120 Hz
The protocol SPR2-230.105.01.02.02 is required for
these instructions
01102628

2 Revision / Disclaimer
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 2 of 26 Medical Solutions
1Revision / Disclaimer
Document revision level
The document corresponds to the version/revision level effective at the time of system
delivery. Revisions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
Table of Contents 3
Page 3 of 26
Medical Solutions
0Table of Contents
1 _______ General information______________________________________________ 4
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Required documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required tools, measurement and auxiliary devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Emphasized text. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety information and protective measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General safety information (in existing documents) . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General electrical safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Radiation safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mechanical safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety information - risk of infection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Information on the protective conductor resistance test . . . . . . . . . . . . . . . . . . . . . . 10
Information on measuring the system leakage current . . . . . . . . . . . . . . . . . . . . . . . 11
Descriptions of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2 _______ Inspection of exterior and surroundings____________________________ 17
Inspection of exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Inspection of surroundings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3 _______ Safety inspection _______________________________________________ 19
Mechanical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4 _______ Maintenance, operating value/functional inspection __________________ 23
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5 _______ Final result/quality inspection and maintenance _____________________ 24
6 _______ Changes to Previous Version_____________________________________ 25

4 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 4 of 26 Medical Solutions
1-
1 General information
1.1 Requirements
These maintenance instructions apply to the 100/120 Hz standard monitor,
part number 30 64 581 B5310.
The monitor is a component of the system or system configuration. Maintenance for
these systems or system configurations should be performed in accordance with the cor-
responding maintenance instructions.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 5
Page 5 of 26
Medical Solutions
1.2 Required documents
•Safety information according to ARTD, part 2
•Maintenance protocol SPR2-230.105.01..
•System binder for the system or system configura-
tion

6 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 6 of 26 Medical Solutions
1.3 Required tools, measurement and auxiliary devices
NOTE The indicated articles are listed in the STC (Service Tools Catalog)
unless otherwise stated (the STC is a component of the Spare
Parts Catalog), except for those items identified with "*".
Tool For example Material no.:
•Standard tool kit*
•Set of Allen keys*
•Protective conductor tester Safety tester UNIMRT 1100 51 38 727
•Luminance meter SPOTMETER for SM fit ACT 77 52 848

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 7
Page 7 of 26
Medical Solutions
1.4 Emphasized text
Fig. 1: Safety Notes
DANGER
!
WARNING
!
CAUTION
!
NOTICE
DANGER indicates when there is an immediate danger that
l e a d s to death or serious physical injury.
WARNING indicates a risk of danger that m a y l e a d to death
or serious physical injury.
CAUTION used with the safety alert symbol indicates a risk of
danger that leads to slight or moderate physical injury and/ or
damage to property.
NOTICE used without the safety alert symbol indicates a risk of
danger that if disregarded leads or may lead to a potential
situation which may result in an undesirable result or state other
than death, physical injury or property damage.

8 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 8 of 26 Medical Solutions
1.5 Safety information and protective measures
1.5.1 General safety information (in existing documents)
WARNING Risk of injury, death or material damage.
Note
¹The product-specific safety notes in these instructions,
¹The general safety information in TD00-000.860.01... and
¹The safety information in accordance with ARTD Part 2.
¹Non-compliance can lead to death, injury or material
damage.
1.5.2 General electrical safety information
WARNING Electrical safety!
Non-compliance can lead to severe injury or even death and mate-
rial damage.
¹After opening the covers, the parts under voltage are
accessible. To avoid danger, disconnect the system from
the power supply prior to opening the covers. Discon-
nect the power plug.
¹If an uninterruptible power supply (UPS) is installed in
the system, the voltage output of the UPS must also be
deenergized or the voltage output plug must be discon-
nected.
¹If work has to be performed under electrical voltage, the
general safety information according to
TD00-000.860.01... must be complied with.
CAUTION Electrical voltage!
Non-compliance can result in material damage.
¹When working on the system, ESD regulations must be
observed.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 9
Page 9 of 26
Medical Solutions
1.5.3 Radiation safety information
WARNING X-ray radiation!
Non-compliance can lead to illness, irreversible damage to body
cells and the genotype, severe injury and even death.
When performing work on the system during which radiation must
be released, the radiation protection directives and the rules for ra-
diation protection according to ARTD 02.731.02 must be complied
with.
¹Please note:
¹Use available radiation protection devices.
¹Wear radiation protection clothing (lead apron).
¹Stay as far away as possible from the radiation source.
¹Release radiation only if necessary.
¹Set the radiation activity as low as possible. (low kV and
mA values, short radiation time)
¹Release radiation for as short a time as possible.
¹Checks in which radiation must be released are identified
by the radiation warning symbol.
1.5.4 Mechanical safety information
CAUTION Risk of burns from hot parts or components! Non-compliance can
result in minor to more severe burns, especially on the hands.
Parts and components (e.g., power components, cooling element,
electromagnetic brakes) that can exceed 50 degrees Celsius dur-
ing operation are accessible after the covers are opened.
¹To avoid burns, switch the system off prior to touching
parts or components and allow at least 5 minutes of cool-
ing.
CAUTION Risk of injury from mechanical parts! Non-compliance can result
in minor to more severe injury, especially to the hands.
Parts such as flat plugs, threaded bolts, cut-off cable ties and com-
ponent edges that, if care is not taken, can cause crushing, abra-
sion and cuts to the skin, particularly to the hands, can be touched
after the covers are opened.
¹Perform the required work with special care and atten-
tion to detail.
¹If needed, wear work gloves.

10 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 10 of 26 Medical Solutions
1.5.5 Safety information - risk of infection
WARNING Risk of infection due to pathogens! Non-compliance can lead to
severe injury and even death.
This product can be contaminated by infected blood or other bodi-
ly fluids.
¹Avoid all contact with blood or other bodily fluids!
¹Strictly observe the safety information in
ARTD-002.731.37... regarding prevention of infectious
diseases during customer service calls.
1.5.6 Information on the protective conductor resistance test
Observe the instructions in the safety rules for installation and repair (ARTD-002.731.17
...).
The protective conductor resistance is to be measured, documented, and evaluated dur-
ing maintenance.
NOTE Evaluate the results by comparing the first measured value to the
corresponding values documented during preceding maintenance
procedures or safety checks.
A sudden or unexpected increase in the measured values may in-
dicate a defect in the protective conductor connections - even if
the limit value of 0.2 ohms is not exceeded.
(Protective conductor or contacts).
The measurement must be performed according to DIN VDE 0751, Part 1 (see ARTD
Part 2). In this case the protective conductor resistance for all touchable conductive parts
must be measured during the normal operating state of the system.
Make sure that control cables or data cables between the components of the system are
not mistaken for a protective conductor connection.
During the measurement, move the power cable and additional connection cables with an
integrated protective conductor section by section to detect cable breaks.
Units with fixed power line connection:
The protective conductor resistance of 0.2 ohms must not be exceeded.
Units with detachable power cable:
The protective conductor resistance of 0.2 ohms for the unit with a power line connection
must not be exceeded.
The protective conductor resistance of 0.1 ohms for the detachable power line connection
must not be exceeded.
The protective conductor resistance of 0.1 ohms between the ground contact of the unit
plug and the touchable conductive unit parts may not be exceeded.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 11
Page 11 of 26
Medical Solutions
Fig. 2: Measuring circuit for measuring the protective conductor resistance in units/systems that
are permanently connected to the power supply net (according to DIN VDE
0751-1:2001-10, Fig. C3).
Pos. 1 System
Pos. 2 Application part (not available)
Pos. 3 Measurement setup (integrated into measuring device)
The determined values, including the measuring points, must be recorded and assessed
in the protective conductor resistance report.
The measuring procedure and the measuring device used (designation and serial num-
ber) are also to be documented.
1.5.7 Information on measuring the system leakage current
NOTE The system leakage current measurement is to be conducted and
recorded as the repeat measurement during maintenance.
However, the first measured value must be newly determined and
a new report must created under the following conditions:
Lack of system leakage current measurement documentation
Local line voltage or line frequency deviating from the line voltage
and line frequency documented in the report (e.g. in the event of a
site/operator change)
Use of a different procedure for measuring the system leakage cur-
rent from the one documented in the report.
For the purpose of traceability, reference to the new report is to be
written on the old report. The reason for newly determining the
first measured value is to be documented and confirmed with a
name and signature.

12 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 12 of 26 Medical Solutions
Observe the instructions in the safety rules for installation and repair (ARTD-002.731.17
...).
WARNING Electrical voltage!
Non-compliance can lead to severe injury and even death.
¹The system leakage current measurement may be per-
formed on systems of protection class I only after the
protective conductor test has been passed.
First measured value
The first measured value was already determined and documented in the system leakage
current report. The measuring procedure was also recorded.
The measurement was performed with the recorded line voltage, line frequency and with
the recorded measuring equipment.
Measurement
Perform the measurement according to DIN VDE 0751, Part 1 (see ARTD-002.731.17....),
and record the determined value.
The measuring procedure indicated in the report must be used.
If the first measured value has to be newly determined (see note), a measuring procedure
can be selected (direct measurement or differential measurement).
Measurement of the system leakage current according to the differential current method
(Fig.3/p.12)must be given preference, since this method is not dangerous to the per-
son performing the measurement and other persons.
However, please note the minimum resolution of the leakage current measuring instru-
ment and any additional manufacturer's data restricting the use of the measuring device.
Fig. 3: Measuring circuit for measuring the system leakage current according to the differential
current method in compliance with DIN VDE 0751-1:2001-10, Fig. C6 for protection class

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 13
Page 13 of 26
Medical Solutions
I.
Pos. 1 System
Pos. 2 Application part (not available)
Pos. 3 Measurement setup (integrated into measuring device)
If the direct measurement of the system leakage current is used (Fig.4/p.13), the sys-
tem must be insulated during the measurement and must not be touched.
Fig. 4: Measuring circuit for direct measurement of the system leakage current in compliance
with DIN VDE 0751-1:2001-10, Fig. C5 for protection class I.
Pos. 1 System
Pos. 2 Application part (not available)
Pos. 3 Measurement setup (integrated into measuring device)
WARNING Electrical voltage!
Non-compliance can lead to severe injury and even death.
No housing parts of the system may be touched during direct mea-
surement of the system leakage current (Fig.4/p.13).
¹Third-person access to the system must be prevented.
The system must be switched on during measurement. Measuring devices with auto-
mated measuring sequences must therefore be set to manual measurement.
The highest value must be entered in the system leakage current report.
This value must not exceed the permissible leakage current values according to DIN VDE
0751-1:2001-10, Table F.1, line "general leakage current information", of 0.5 mA.
Measure and record the current line voltage. If the measured line voltage deviates from
the nominal voltage, correct the measured value to the value corresponding to a mea-
surement at the nominal value of the line voltage. This is also to be documented.
Document the measuring procedure (differential measurement or direct measurement)
and the measuring device used (designation and serial number).
In the case of repeat measurements, the measured value is also to be evaluated.

14 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 14 of 26 Medical Solutions
NOTE Evaluate the results by comparing the first measured value to the
corresponding values documented during preceding maintenance
procedures or safety checks.
A sudden or unexpected increase in the measured values may in-
dicate that a fault has occurred in the primary circuit of the power
supply (damaged insulation, damage caused by water ingress or
humidity, defective interference suppressor, etc.) - even if the limit
value of 2.5 mA is not exceeded.
The evaluation is not necessary in the case of a new determination.
File the report sheet in the system folder or log book.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
General information 15
Page 15 of 26
Medical Solutions
1.6 Descriptions of abbreviations
The steps identified by these abbreviations are part of the maintenance report and should
be checked off upon completion.
NOTE The sequence for complete maintenance and inspection is de-
scribed on the following pages.
Each work step must be performed on an annual basis, if not oth-
erwise specified.
Abbrev. Description
SI Safety Inspection
SIE Electrical Safety
SIM Mechanical Safety
PM Preventive Maintenance
PMP Periodic Preventive Maintenance
PMA Preventive Maintenance Adjustments
PMF Preventive Maintenance, Operating Value Check, Function Check
Q Quality Check
QIQ Image Quality
QSQ System Quality Check
SW Software Maintenance

16 General information
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 16 of 26 Medical Solutions
1.7 Maintenance interval
12 months

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
Inspection of exterior and surroundings 17
Page 17 of 26
Medical Solutions
2-
2 Inspection of exterior and surroundings
2.1 Inspection of exterior
PMP Damage
Inspect the monitor for damage, e.g. to the housing or to the finish.

18 Inspection of exterior and surroundings
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 18 of 26 Medical Solutions
2.2 Inspection of surroundings
2.2.1 Power outlets
SIE Damage
For monitors connected directly to the power supply:
•Inspect the power outlet for damage.
SIE Line voltage
•Measure the line voltage and compare this value to the line voltage for the monitor.

Siemens AG SPR2-230.101.01.02.02 Monitor 44cm, 100/120HZ
08.05 CS PS 24
Safety inspection 19
Page 19 of 26
Medical Solutions
3-
3 Safety inspection
3.1 Mechanical safety
SIM Monitor mounting
•Inspect the monitor mounting on the console (rotating/tilting console or monitor holder)
for any mechanic damage.
SIM Console mounting
•Inspect the console (rotating/tilting console or monitor holder) for mechanical damage
and correct mounting.
SIM Warning labels
•Ensure that all required warning labels are attached and in good condition.
¹Replace any illegible labels.
SIM ID labels
•Ensure that all required ID labels are attached and in good condition.
¹Replace any illegible labels.

20 Safety inspection
Monitor 44cm, 100/120HZ SPR2-230.101.01.02.02 Siemens AG
08.05 CS PS 24
Page 20 of 26 Medical Solutions
3.2 Electrical safety
SIE Cables and plugs
•Check visible cables and plugs of the monitor for damage
SIE Protective conductor test
NOTE The protective conductor test for the monitors is to be performed
when these are externally mounted (e.g. on a wall console). It is not
necessary to perform the protective conductor test for monitors
mounted on the monitor trolley of the system if they are tested dur-
ing the protective conductor test of the system (e.g., SIREMOBIL
system).
NOTE Observe the notes on the protective conductor test in these in-
structions. The power cable of the monitor is to be moved section
by section during the protective conductor test to detect cable
breaks.
•If covers were removed, they are to be reattached.
•Perform the protective conductor test according to ARTD-002.731.17... .
•The protective conductor resistance of 0.2 ohms for the unit with a power line connec-
tion must not be exceeded.
The protective conductor resistance of 0.1 ohms for the detachable power cable must
not be exceeded.
The protective conductor resistance of 0.1 ohms between the ground contact of the unit
plug and the touchable conductive unit parts may not be exceeded.
•The determined values, including the measuring points, must be recorded and as-
sessed.
•The measuring procedure and the measuring device used (designation and serial num-
ber) are also to be documented.
NOTE Evaluate the results by comparing the first measured value to the
corresponding values documented during preceding maintenance
procedures or safety checks.
A sudden or unexpected increase in the measured values may in-
dicate a defect in the protective conductor connection - even if the
limit value of 0.2 ohms is not exceeded.
(Protective conductor or contacts)
SIE Leakage current