Siemens SIMATIC Ident User guide

SIMATIC RF200
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC Ident
RFID systems
SIMATIC RF200
System Manual
07/2015
J31069
-D0227-U001-A9-7618
Introduction
1
Safety notes
2
System overview
3
RF200 system planning
4
Readers
5
Antennas
6
Transponder
7
System integration
8
System diagnostics
9
Appendix
A

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
J31069-D0227-U001-A8-7618
Ⓟ
07/2015 Subject to change
Copyright © Siemens AG 2010 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 5
Table of contents
1 Introduction........................................................................................................................................... 15
1.1 Abbreviations and naming conventions..................................................................................16
2 Safety notes.......................................................................................................................................... 17
3 System overview................................................................................................................................... 19
3.1 RFID components and their function ......................................................................................20
3.2 Overview of transponders .......................................................................................................23
4 RF200 system planning......................................................................................................................... 25
4.1 Fundamentals of application planning ....................................................................................25
4.1.1 Selection criteria for SIMATIC RF200 components................................................................25
4.1.2 Transmission window and read/write distance .......................................................................25
4.1.3 Width of the transmission window ..........................................................................................28
4.1.4 Impact of secondary fields ......................................................................................................29
4.1.5 Permissible directions of motion of the transponder...............................................................32
4.1.6 Operation in static and dynamic mode ...................................................................................33
4.1.7 Dwell time of the transponder .................................................................................................34
4.1.8 Communication between communication module, reader and transponder ..........................35
4.2 Field data of transponders and readers..................................................................................36
4.2.1 Field data ................................................................................................................................37
4.2.2 Minimum clearances ...............................................................................................................44
4.3 Installation guidelines..............................................................................................................47
4.3.1 Overview .................................................................................................................................47
4.3.2 Reduction of interference due to metal...................................................................................47
4.3.3 Effects of metal on different transponders and readers..........................................................49
4.3.4 Impact of metal on the transmission window ..........................................................................50
4.3.4.1 RF210R...................................................................................................................................51
4.3.4.2 RF220R...................................................................................................................................54
4.3.4.3 RF240R...................................................................................................................................56
4.3.4.4 RF250R...................................................................................................................................59
4.3.4.5 RF260R...................................................................................................................................65
4.3.4.6 RF290R...................................................................................................................................67
4.3.5 Installation and connection of 2 to 6 antennas with one RF290R reader...............................71
4.3.5.1 Installation options with the antenna splitter (2-4 antennas) ..................................................
72
4.3.5.2 Antenna installation.................................................................................................................75
4.3.5.3 Installation options with the antenna multiplexer (2-6 antennas) ...........................................79
4.3.6 Chemical resistance of the transponders ...............................................................................80
4.3.6.1 Overview of the transponders and their housing materials ....................................................80
4.3.6.2 Polyphenylene sulfide (PPS) ..................................................................................................81
4.3.6.3 Polycarbonate (PC).................................................................................................................82
4.3.6.4 Polyvinyl chloride (PVC) .........................................................................................................83
4.3.6.5 Epoxy resin .............................................................................................................................83
4.3.6.6 PA6.6 GF30 ............................................................................................................................86

Table of contents
SIMATIC RF200
6System Manual, 07/2015, J31069-D0227-U001-A9-7618
4.4 Further information................................................................................................................. 87
5 Readers................................................................................................................................................ 89
5.1 SIMATIC RF210R .................................................................................................................. 90
5.1.1 Features ................................................................................................................................. 90
5.1.2 RF210R ordering data ........................................................................................................... 90
5.1.3 Pin assignment RF210R with RS422 interface...................................................................... 91
5.1.4 Display elements of the RF210R reader................................................................................ 91
5.1.5 Minimum distance between RF210R readers........................................................................ 92
5.1.6 Technical specifications of the RF210R reader ..................................................................... 93
5.1.7 Approvals ............................................................................................................................... 94
5.1.8 Dimension drawing ................................................................................................................ 95
5.2 SIMATIC RF210M.................................................................................................................. 96
5.2.1 Features ................................................................................................................................. 96
5.2.2 Ordering data RF210M .......................................................................................................... 96
5.2.3 Installing the RF210M reader................................................................................................. 97
5.2.4 Pin assignment RF210M with RS-422 interface .................................................................... 97
5.2.5 Display elements of the RF210M reader ............................................................................... 98
5.2.6 Technical specifications of the RF210M reader..................................................................... 98
5.2.7 Approvals ............................................................................................................................. 100
5.2.8 Dimension drawing .............................................................................................................. 101
5.3 SIMATIC RF220R ................................................................................................................ 102
5.3.1 Features ............................................................................................................................... 102
5.3.2 RF220R ordering data ......................................................................................................... 102
5.3.3 RF220R pin assignment with RS422 interface .................................................................... 103
5.3.4 Display elements of the RF220R reader.............................................................................. 103
5.3.5 Minimum distance between RF220R readers...................................................................... 104
5.3.6 Technical specifications of the RF220R reader ................................................................... 105
5.3.7 Approvals ............................................................................................................................. 106
5.3.8 Dimension drawing .............................................................................................................. 107
5.4 SIMATIC RF240R ................................................................................................................ 108
5.4.1 Features ............................................................................................................................... 108
5.4.2 RF240R ordering data ......................................................................................................... 108
5.4.3 Pin assignment RF240R ...................................................................................................... 109
5.4.4 Display elements of the RF240R reader.............................................................................. 109
5.4.5 Minimum distance between several RF240R readers......................................................... 110
5.4.6 Technical specifications of the RF240R reader ................................................................... 111
5.4.7 Approvals ............................................................................................................................. 113
5.4.8 Dimension drawing .............................................................................................................. 114
5.5 SIMATIC RF250R ................................................................................................................ 115
5.5.1 Features ............................................................................................................................... 115
5.5.2 Ordering data RF250R......................................................................................................... 115
5.5.3 Pin assignment RF250R ...................................................................................................... 116
5.5.4 Display elements of the RF250R reader.............................................................................. 116
5.5.5 Technical specifications of the RF250R reader ................................................................... 117
5.5.6 Approvals ............................................................................................................................. 118
5.5.7 Dimension drawing .............................................................................................................. 120
5.6 SIMATIC RF260R ................................................................................................................ 121
5.6.1 Features ............................................................................................................................... 121
5.6.2 Ordering data for RF260R ................................................................................................... 121

Table of contents
SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 7
5.6.3 Pin assignment RF260R.......................................................................................................122
5.6.4 Display elements of the RF260R reader...............................................................................122
5.6.5 Minimum distance between several RF260R .......................................................................123
5.6.6 Technical data of the RF260R reader...................................................................................124
5.6.7 Approvals ..............................................................................................................................126
5.6.8 Dimension drawing ...............................................................................................................127
5.7 SIMATIC RF290R .................................................................................................................128
5.7.1 Features................................................................................................................................128
5.7.2 Ordering data RF290R..........................................................................................................129
5.7.3 Pin assignment RF290R.......................................................................................................130
5.7.4 Display elements of the RF290R reader...............................................................................132
5.7.5 Installing the RF290R reader................................................................................................133
5.7.5.1 Wall mounting .......................................................................................................................133
5.7.5.2 Installing on the S7-300 standard rail ...................................................................................134
5.7.5.3 Installation on a DIN rail........................................................................................................134
5.7.6 Technical specifications of the RF290R reader....................................................................136
5.7.7 Approvals ..............................................................................................................................137
5.7.8 Note on the use of the RF290R as a replacement for SLG D10 / SLG D10S......................139
5.7.9 Dimension drawing ...............................................................................................................140
6 Antennas ............................................................................................................................................ 141
6.1 ANT 3....................................................................................................................................142
6.1.1 Features................................................................................................................................142
6.1.2 Ordering data ........................................................................................................................142
6.1.3 Mounting on/in metal.............................................................................................................143
6.1.4 Operating / limit distances ....................................................................................................144
6.1.5 Minimum spacing ..................................................................................................................144
6.1.6 Technical data.......................................................................................................................146
6.1.7 Dimension drawing ...............................................................................................................147
6.2 ANT 8....................................................................................................................................148
6.2.1 Features................................................................................................................................148
6.2.2 Ordering data ........................................................................................................................148
6.2.3 Transmission window............................................................................................................149
6.2.4 Flush-mounted in metal ........................................................................................................149
6.2.5 Minimum spacing ..................................................................................................................150
6.2.6 Technical data.......................................................................................................................151
6.2.7 Dimension drawing ...............................................................................................................152
6.3 ANT 12..................................................................................................................................153
6.3.1 Features................................................................................................................................153
6.3.2 Ordering data ........................................................................................................................153
6.3.3 Transmission window............................................................................................................154
6.3.4 Flush-mounted in metal ........................................................................................................154
6.3.5 Minimum spacing ..................................................................................................................155
6.3.6 Technical data.......................................................................................................................156
6.3.7 Dimension drawing ...............................................................................................................
157
6.4 ANT 18..................................................................................................................................158
6.4.1 Features................................................................................................................................158
6.4.2 Ordering data ........................................................................................................................158
6.4.3 Transmission window............................................................................................................159
6.4.4 Flush-mounted in metal ........................................................................................................159

Table of contents
SIMATIC RF200
8System Manual, 07/2015, J31069-D0227-U001-A9-7618
6.4.5 Minimum spacing ................................................................................................................. 160
6.4.6 Technical data...................................................................................................................... 161
6.4.7 Dimension drawing .............................................................................................................. 162
6.5 ANT 30 ................................................................................................................................. 163
6.5.1 Features ............................................................................................................................... 163
6.5.2 Ordering data ....................................................................................................................... 163
6.5.3 Transmission window........................................................................................................... 164
6.5.4 Flush-mounted in metal ....................................................................................................... 165
6.5.5 Minimum spacing ................................................................................................................. 165
6.5.6 Technical data...................................................................................................................... 167
6.5.7 Dimension drawing .............................................................................................................. 168
6.6 ANT D5 ................................................................................................................................ 169
6.6.1 Features ............................................................................................................................... 169
6.6.2 Ordering data ....................................................................................................................... 169
6.6.3 Transmission window........................................................................................................... 170
6.6.4 Flush-mounted in metal ....................................................................................................... 171
6.6.5 Minimum spacing ................................................................................................................. 171
6.6.6 Technical data...................................................................................................................... 173
6.6.7 Dimension drawing .............................................................................................................. 174
6.7 ANT D6 ................................................................................................................................ 175
6.7.1 Features ............................................................................................................................... 175
6.7.2 Ordering data ....................................................................................................................... 175
6.7.3 Transmission window........................................................................................................... 176
6.7.4 Metal-free area..................................................................................................................... 177
6.7.5 Minimum spacing ................................................................................................................. 177
6.7.6 Technical data...................................................................................................................... 178
6.7.7 Dimensional diagram ........................................................................................................... 179
6.8 ANT D10 .............................................................................................................................. 180
6.8.1 Features ............................................................................................................................... 180
6.8.2 Ordering data ....................................................................................................................... 180
6.8.3 Transmission window........................................................................................................... 181
6.8.4 Metal-free area..................................................................................................................... 182
6.8.5 Minimum spacing ................................................................................................................. 183
6.8.6 Technical data...................................................................................................................... 184
6.8.7 Dimensional diagram ........................................................................................................... 185
7 Transponder ........................................................................................................................................187
7.1 Memory configuration of ISO the transponders ................................................................... 187
7.2 MDS D100............................................................................................................................ 188
7.2.1 Characteristics ..................................................................................................................... 188
7.2.2 Ordering data ....................................................................................................................... 189
7.2.3 Metal-free area..................................................................................................................... 189
7.2.4 Technical data...................................................................................................................... 191
7.2.5 Dimension drawing .............................................................................................................. 192
7.3 MDS D117............................................................................................................................ 193
7.3.1 Features ............................................................................................................................... 193
7.3.2 Ordering data ....................................................................................................................... 193
7.3.3 Mounting in metal................................................................................................................. 193
7.3.4 Technical specifications ....................................................................................................... 194

Table of contents
SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 9
7.3.5 Dimension drawing ...............................................................................................................195
7.4 MDS D124 ............................................................................................................................196
7.4.1 Characteristics ......................................................................................................................196
7.4.2 Ordering data ........................................................................................................................196
7.4.3 Mounting on metal ................................................................................................................197
7.4.4 Technical specifications ........................................................................................................198
7.4.5 Use of the MDS D124 in hazardous area .............................................................................199
7.4.6 Dimension drawing ...............................................................................................................201
7.5 MDS D126 ............................................................................................................................201
7.5.1 Characteristics ......................................................................................................................201
7.5.2 Ordering data ........................................................................................................................202
7.5.3 Technical specifications ........................................................................................................202
7.5.4 Dimension drawing ...............................................................................................................203
7.6 MDS D127 ............................................................................................................................204
7.6.1 Features................................................................................................................................204
7.6.2 Ordering data ........................................................................................................................204
7.6.3 Mounting in metal..................................................................................................................205
7.6.4 Technical specifications ........................................................................................................206
7.6.5 Dimension drawing ...............................................................................................................207
7.7 MDS D139 ............................................................................................................................208
7.7.1 Characteristics ......................................................................................................................208
7.7.2 Ordering data ........................................................................................................................208
7.7.3 Metal-free area......................................................................................................................
209
7.7.4 Mounting in metal..................................................................................................................210
7.7.5 Cleaning the transponder .....................................................................................................210
7.7.6 Technical specifications ........................................................................................................211
7.7.7 Use of the MDS D139 in hazardous areas ...........................................................................212
7.7.8 Dimension drawings..............................................................................................................214
7.8 MDS D160 ............................................................................................................................215
7.8.1 Characteristics ......................................................................................................................215
7.8.2 Ordering data ........................................................................................................................215
7.8.3 Mounting on metal ................................................................................................................216
7.8.4 Technical specifications ........................................................................................................217
7.8.5 Dimension drawings..............................................................................................................219
7.9 MDS D165 ............................................................................................................................220
7.9.1 Features................................................................................................................................220
7.9.2 Ordering data ........................................................................................................................220
7.9.3 Technical data.......................................................................................................................221
7.9.4 Dimension drawing ...............................................................................................................222
7.10 MDS D200 ............................................................................................................................223
7.10.1 Features................................................................................................................................223
7.10.2 Ordering data ........................................................................................................................223
7.10.3 Mounting on metal ................................................................................................................224
7.10.4 Technical data.......................................................................................................................225
7.10.5 Dimension drawing ...............................................................................................................227
7.11 MDS D261 ............................................................................................................................227
7.11.1 Features................................................................................................................................
227
7.11.2 Ordering data ........................................................................................................................227

Table of contents
SIMATIC RF200
10 System Manual, 07/2015, J31069-D0227-U001-A9-7618
7.11.3 Technical data...................................................................................................................... 228
7.11.4 Dimension drawing .............................................................................................................. 229
7.12 MDS D324............................................................................................................................ 230
7.12.1 Characteristics ..................................................................................................................... 230
7.12.2 Ordering data ....................................................................................................................... 230
7.12.3 Metal-free area..................................................................................................................... 231
7.12.4 Technical specifications ....................................................................................................... 232
7.12.5 Dimension drawing .............................................................................................................. 233
7.13 MDS D339............................................................................................................................ 234
7.13.1 Characteristics ..................................................................................................................... 234
7.13.2 Ordering data ....................................................................................................................... 234
7.13.3 Mounting on metal ............................................................................................................... 235
7.13.4 Mounting in metal................................................................................................................. 236
7.13.5 Cleaning the transponder..................................................................................................... 236
7.13.6 Technical specifications ....................................................................................................... 237
7.13.7 Use of the MDS D339 in hazardous areas .......................................................................... 238
7.13.8 Dimensional drawing............................................................................................................ 240
7.14 MDS D400............................................................................................................................ 241
7.14.1 Features ............................................................................................................................... 241
7.14.2 Ordering data ....................................................................................................................... 241
7.14.3 Mounting on metal ............................................................................................................... 242
7.14.4 Technical specifications ....................................................................................................... 243
7.14.5 Dimension drawing .............................................................................................................. 245
7.15 MDS D421............................................................................................................................ 246
7.15.1 Characteristics ..................................................................................................................... 246
7.15.2 Ordering data ....................................................................................................................... 246
7.15.3 Mounting on metal ............................................................................................................... 247
7.15.4 Technical specifications ....................................................................................................... 249
7.15.5 Dimension drawing .............................................................................................................. 250
7.16 MDS D422............................................................................................................................ 251
7.16.1 Characteristics ..................................................................................................................... 251
7.16.2 Ordering data ....................................................................................................................... 251
7.16.3 Mounting in metal................................................................................................................. 251
7.16.4 Technical specifications ....................................................................................................... 252
7.16.5 Dimension drawing .............................................................................................................. 253
7.17 MDS D423............................................................................................................................ 254
7.17.1 Characteristics ..................................................................................................................... 254
7.17.2 Ordering data ....................................................................................................................... 254
7.17.3 Mounting on metal ............................................................................................................... 255
7.17.4 Technical specifications ....................................................................................................... 256
7.17.5 Dimensional drawing............................................................................................................ 258
7.18 MDS D424............................................................................................................................ 258
7.18.1 Characteristics ..................................................................................................................... 258
7.18.2 Ordering data ....................................................................................................................... 259
7.18.3 Mounting on metal ............................................................................................................... 259
7.18.4 Technical specifications ....................................................................................................... 260
7.18.5 Dimension drawing .............................................................................................................. 262

Table of contents
SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 11
7.19 MDS D425 ............................................................................................................................262
7.19.1 Characteristics ......................................................................................................................262
7.19.2 Ordering data ........................................................................................................................263
7.19.3 Application example of MDS D425 .......................................................................................263
7.19.4 Technical specifications........................................................................................................264
7.19.5 Dimension drawing ...............................................................................................................265
7.20 MDS D426 ............................................................................................................................266
7.20.1 Characteristics ......................................................................................................................266
7.20.2 Ordering data ........................................................................................................................266
7.20.3 Technical specifications........................................................................................................267
7.20.4 Dimension drawing ...............................................................................................................268
7.21 MDS D428 ............................................................................................................................269
7.21.1 Characteristics ......................................................................................................................269
7.21.2 Ordering data ........................................................................................................................269
7.21.3 Application example..............................................................................................................270
7.21.4 Technical specifications........................................................................................................270
7.21.5 Dimension drawing ...............................................................................................................272
7.22 MDS D460 ............................................................................................................................272
7.22.1 Characteristics ......................................................................................................................272
7.22.2 Ordering data ........................................................................................................................273
7.22.3 Mounting on metal ................................................................................................................273
7.22.4 Technical specifications........................................................................................................274
7.22.5 Dimension drawings..............................................................................................................
275
7.23 MDS D521 ............................................................................................................................276
7.23.1 Characteristics ......................................................................................................................276
7.23.2 Ordering data ........................................................................................................................276
7.23.3 Mounting on metal ................................................................................................................276
7.23.4 Technical specifications........................................................................................................279
7.23.5 Dimension drawing ...............................................................................................................280
7.24 MDS D522 ............................................................................................................................281
7.24.1 Characteristics ......................................................................................................................281
7.24.2 Ordering data ........................................................................................................................281
7.24.3 Mounting in metal..................................................................................................................281
7.24.4 Technical specifications........................................................................................................282
7.24.5 Dimension drawing ...............................................................................................................283
7.25 MDS D522 special variant ....................................................................................................284
7.25.1 Characteristics ......................................................................................................................284
7.25.2 Ordering data ........................................................................................................................284
7.25.3 Mounting in metal..................................................................................................................285
7.25.4 Installation instructions..........................................................................................................286
7.25.5 Technical specifications........................................................................................................287
7.25.6 Dimensional drawing.............................................................................................................288
7.26 MDS D524 ............................................................................................................................289
7.26.1 Characteristics ......................................................................................................................289
7.26.2 Ordering data ........................................................................................................................289
7.26.3 Mounting on metal ................................................................................................................290
7.26.4 Technical specifications........................................................................................................291
7.26.5 Dimension drawing ...............................................................................................................292

Table of contents
SIMATIC RF200
12 System Manual, 07/2015, J31069-D0227-U001-A9-7618
7.27 MDS D526............................................................................................................................ 293
7.27.1 Characteristics ..................................................................................................................... 293
7.27.2 Ordering data ....................................................................................................................... 293
7.27.3 Technical specifications ....................................................................................................... 294
7.27.4 Dimension drawing .............................................................................................................. 295
7.28 MDS D528............................................................................................................................ 296
7.28.1 Characteristics ..................................................................................................................... 296
7.28.2 Ordering data ....................................................................................................................... 296
7.28.3 Application example............................................................................................................. 297
7.28.4 Technical specifications ....................................................................................................... 297
7.28.5 Dimension drawing .............................................................................................................. 299
8 System integration ...............................................................................................................................301
9 System diagnostics ..............................................................................................................................305
9.1 Error codes of the RF200 readers ....................................................................................... 305
9.2 Diagnostic functions ............................................................................................................. 306
9.2.1 Reader diagnostics with SLG STATUS ............................................................................... 306
9.2.2 Transponder diagnostics with MDS STATUS...................................................................... 308
A Appendix .............................................................................................................................................309
A.1 Certificates and approvals ................................................................................................... 309
A.2 Accessories.......................................................................................................................... 311
A.2.1 Antenna splitter .................................................................................................................... 311
A.2.2 Antenna multiplexer SIMATIC RF260X ............................................................................... 313
A.2.2.1 Characteristics ..................................................................................................................... 313
A.2.2.2 Ordering data ....................................................................................................................... 313
A.2.2.3 Description ........................................................................................................................... 314
A.2.2.4 Principle of operation ........................................................................................................... 314
A.2.2.5 Connectors........................................................................................................................... 315
A.2.2.6 Configuration........................................................................................................................ 316
A.2.2.7 Parameterization.................................................................................................................. 317
A.2.2.8 RF260X commands ............................................................................................................. 318
A.2.2.9 Technical specifications ....................................................................................................... 319
A.2.2.10 Dimensional drawing............................................................................................................ 320
A.2.3 Wide-range power supply unit for SIMATIC RF systems .................................................... 321
A.2.3.1 Features ............................................................................................................................... 321
A.2.3.2 Scope of supply.................................................................................................................... 322
A.2.3.3 Ordering data ....................................................................................................................... 322
A.2.3.4 Safety Information................................................................................................................ 322
A.2.3.5 Connecting ........................................................................................................................... 323
A.2.3.6 Technical specifications ....................................................................................................... 324
A.2.3.7 Pin assignment of DC outputs and mains connection ......................................................... 326
A.2.3.8 Dimension drawing .............................................................................................................. 327
A.2.3.9 Certificates and approvals ................................................................................................... 328
A.2.4 Transponder holders............................................................................................................ 329
A.3 Connecting cable ................................................................................................................. 335
A.3.1 Reader RF2xxR (RS-422) with ASM 456 / RF160C / RF170C / RF180C / RF182C .......... 335
A.3.2 Reader RF2xxR (RS-422) with ASM 475 ............................................................................ 337
A.3.3 Reader RF2xxR (RS-422) with RF120C.............................................................................. 338
A.3.4 Reader RF240R/RF260R/RF290R (RS232) with PC .......................................................... 338

Table of contents
SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 13
A.4 Ordering data ........................................................................................................................340
A.5 Service & Support .................................................................................................................350
Glossary ............................................................................................................................................. 353
Index................................................................................................................................................... 359

Table of contents
SIMATIC RF200
14 System Manual, 07/2015, J31069-D0227-U001-A9-7618

SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 15
Introduction
1
Introduction
SIMATIC RF200 is a compact RFID system in the SIMATIC RFID product family. The
product range comprises cost-efficient RF readers that are ideal for use in small assembly
lines or in intralogistics. SIMATIC RF200 RFID readers only support the RFID standard ISO
15693 and are therefore ideal for operation with the extensive range of ISO 15693
transponders.
The readers of the RF200 product family are available with the following interfaces:
●RS-422 for connecting to the communications modules
●RS-232 with a simple ASCII protocol for connection to PCs and third-party controllers
●IO-Link for connection to IO Link masters from Siemens and third-party controllers
Readers with an internal antenna have a particularly compact design
(RF210R/RF220R/RF240R/RF260R). RF250R and RF290R are designed for operation with
external antennas either to achieve longer distances or larger field sizes (RF290R with ANT
D5/D6/D10) or to allow installation where there is very little space (RF250R with ANT
3/8/12/18/30).
Scope of validity of this document
This documentation is valid for all variants of the SIMATIC RF200 system and describes the
devices shipped as of July 2015.
Registered trademarks
SIMATIC ®, SIMATIC RF ®, MOBY ®, RF MANAGER ® and SIMATIC Sensors ® are registered
trademarks of Siemens AG.
Further information
For additional information, refer to the manuals:
●Function manual "Ident profile and Ident blocks"
(https://support.industry.siemens.com/cs/us/en/view/106368029)
●Function manual "FB 45"
(https://support.industry.siemens.com/cs/ww/en/view/21738808)
●Operating instructions "RF200 IO-Link"
(https://support.industry.siemens.com/cs/ww/en/view/60641859)
●System manual "MOBY D"
(https://support.industry.siemens.com/cs/ww/en/view/13628689)

Introduction
1.1 Abbreviations and naming conventions
SIMATIC RF200
16 System Manual, 07/2015, J31069-D0227-U001-A9-7618
●Operating instructions "RF310M"
(https://support.industry.siemens.com/cs/us/en/view/51812642)
●Product information "RF200 command set"
(https://support.industry.siemens.com/cs/us/en/view/44864850)
History
The following issues of the SIMATIC RF200 system manual have been published:
Output
Note
03/2011
First edition
05/2011 Expansion of the documentation with the addition of the device variant RF260R with
RS-232 interface
09/2011
Expansion of the documentation with the device variant RF240R
03/2013 Expansion of the documentation with the device variant RF290R
09/2013 Expansion of the documentation by the following:
•the device variant RF250R
•the device variants RF240R and RF260R with ASCII interface
•Antennas ANT 8, ANT 12, ANT 18 and ANT 30
•Transponders
07/2015 Expansion of the documentation by the following:
•ANT 3 antennas
•MDS D5xx transponder
•Mobile reader RF210R
1.1
Abbreviations and naming conventions
The following terms/abbreviations are used synonymously in this document:
Write/read device (SLG)
Readers
Mobile data storage unit (MDS)
Transponder, tag
Interface module (ASM)
Communications module (CM)

SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 17
Safety notes
2
SIMATIC RFID products comply with the salient safety specifications to IEC, VDE, EN, UL
and CSA. If you have questions about the validity of the installation in the planned
environment, please contact your service representative.
NOTICE
Alterations to the devices are not permitted.
Failure to observe this requirement shall constitute a revocation of the radio equipment
approval, CE approval and manufacturer's warranty.
Repairs
Repairs may only be carried out by authorized qualified personnel.
WARNING
Unauthorized opening of and improper repairs to the device may result in substantial
damage to equipment or risk of personal injury to the user.
System expansion
Only install system expansion devices designed for this device. If you install other upgrades,
you may damage the system or violate the safety requirements and regulations for radio
frequency interference suppression. Contact your technical support team or your sales outlet
to find out which system upgrades are suitable for installation.
NOTICE
If you cause system defects by installing or exchanging system expansion devices, the
warranty becomes void.

Safety notes
SIMATIC RF200
18 System Manual, 07/2015, J31069-D0227-U001-A9-7618

SIMATIC RF200
System Manual, 07/2015, J31069-D0227-U001-A9-7618 19
System overview
3
SIMATIC RF200 is an inductive identification system that is compatible with the ISO 15693
standard and was specially designed for use in industrial production for the control and
optimization of material flows.
In contrast to SIMATIC RF300, SIMATIC RF200 is intended for RFID applications where
performance requirements are not very high, for example with regard to data volume,
transfer rate or diagnostics options. SIMATIC RF200 is characterized by particularly
favorable prices.

System overview
3.1 RFID components and their function
SIMATIC RF200
20 System Manual, 07/2015, J31069-D0227-U001-A9-7618
3.1
RFID components and their function
RF200 system components
Figure 3-1 RF200 system overview