Siemens 7XV5810 0BA00 User manual

Wide-range power supplies
7XV5810 0BA00 (24 V)
7XV5810 0CA00 (5 V)
Operating Instructions

C53000-B1140-C602-1
Seite 2 von 20 Operating Instructions 7XV5810 0xA00
Table of content
1GENERAL INSTRUCTIONS.........................................................................................................3
1.1Safety Notes ................................................................................................................................4
1.2General hints ...............................................................................................................................5
1.3Customer Support .......................................................................................................................5
1.4Statement of Conformity..............................................................................................................6
1.5Further Standards .......................................................................................................................6
1.6Used Symbols .............................................................................................................................6
1.7Exclusion of liability .....................................................................................................................7
1.8Copyright .....................................................................................................................................7
1.9Operating Instructions .................................................................................................................8
1.10Scope of Application ...............................................................................................................8
1.11Description of the functional unit.............................................................................................8
1.12In case of a short-circuit..........................................................................................................8
1.13Switching off the device ..........................................................................................................8
1.14Installation ...............................................................................................................................8
1.15Connection ..............................................................................................................................9
1.16Commissioning........................................................................................................................9
1.17Maintenance..........................................................................................................................10
2TECHNICAL DATA ....................................................................................................................11
2.1Power supply 7XV5810 0BA00 (24 V) ......................................................................................11
2.2Power supply 7XV5810 0CA00 (5 V) ........................................................................................12
2.3Combined specifications ...........................................................................................................13
2.4Dimension Drawings .................................................................................................................18
2.5Connection terminals 7XV5810-0BA00 (24 V)..........................................................................19
2.6Connection terminals 7XV5810-0CA00 (5 V)............................................................................19
2.7Ordering Data ............................................................................................................................20
Figures
Figure 1: Dimension Drawings (in mm)................................................................................................. 18
Tables
Table 1: Connection terminals for the 24 V wide-range power supply ................................................. 19
Table 2: Connection terminals for the 5 V wide-range power supply ................................................... 19
Table 3: Ordering Data of the wide-range power supplies.................................................................... 20

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 3 von 20
1 General Instructions
This manual includes the information required for the normal use of the products
described therein. It is intended for technically qualified personnel who has been
specially trained or has special knowledge in the fields of protection-,
instrumentation-, control-, and automatic control engineering (called automation in
the following).
The knowledge and the technically correct translation of the safety instructions and
warnings included in this manual are a prerequisite for the safe installation and
commissioning, as well as for safety during operation and maintenance, of the
product described. Only qualified personnel, as defined in the following explanation,
possess the technical knowledge required to interpret correctly and to put into action
for each individual case the safety instructions and warnings given in this document
in a general manner.
This manual is an integral part of the scope of delivery. However, it cannot take into
account every detail on all types of the described product and also every possible
case regarding installation, operation or maintenance. If further information is desired
or in case special problems should arise, which are not treated adequately in this
document, it is possible to obtain additional details from the local Siemens office or
from the addresses stated in the back of this manual.
Additionally, we point out that the content of this product documentation is not part of
or modifies any previous or existing agreement, promise, or legal relationship.
All obligations by Siemens result from the respective purchase order which also
includes the complete and exclusively valid warranty provision. The contractual
warranty regulations are neither extended nor limited by the statements in this
document.

C53000-B1140-C602-1
Seite 4 von 20 Operating Instructions 7XV5810 0xA00
1.1 Safety Notes
These operating instructions contain notes that are to be complied with for your
personal safety as well as to avoid property damages. These notes are marked by a
triangular warning symbol and the different degrees of danger are categorized as
follows:
Danger
Disregard of the corresponding precautionary measures will
cause death, severe bodily injury or considerable property
damage.
Warning
Disregard of the corresponding precautionary measures
may cause death, severe bodily injury or considerable
property damage.
Attention
Disregard of the corresponding precautionary measures
may lead to slight bodily injury or minor property damage
Note
Shall draw your attention to special information on the
product, product handling or the corresponding section of
the documentation.
Qualified personnel
Commissioning and operation of the equipment is to be
performed by qualified personnel only. In the context of
safety notes in this manual, the term qualified personnel
refers to persons authorized to perform commissioning,
grounding and labelling of devices, systems and electrical
circuits.

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 5 von 20
1.2 General hints
Enclosure
The enclosure must comply with the requirements for the
fire protection enclosure according to the standard
EN 60950.
Warning
This device is designed to be used in enclosures or
closed rooms. Operating the devices outside of the
enclosures can lead to electro-magnetic disturbances
and – in case of a defect – to a fire hazard.
Warning
The device must be operated only within the scope of its
intended use according to these operating instructions
and in connection with third-party equipment or
compounds recommended or accepted by Siemens.
Faultless and safe operation of the product require
proper transport, storage, mounting and installation as
well as careful operation and maintenance.
1.3 Customer Support
For any questions concerning your system, please contact your Siemens
representative. The Siemens Customer Support Center provides around-the-clock
support.
Phone: [phone]
Fax: [phone]
Internet: http://www.siprotec.com
E-Mail: [email protected]m

C53000-B1140-C602-1
Seite 6 von 20 Operating Instructions 7XV5810 0xA00
1.4 Statement of Conformity
Low-voltage Directive 2014/35/EU
EMC Council Directive 2014/30/EU
This conformity has been established by means of tests conducted by
Siemens AG according to the Council Directive in agreement with the
generic standard EN 60255-26 for the EMC directives, and with the
standard EN 61010-1 for the low-voltage directive.
1.5 Further Standards
This product is UL-certified, based on the technical data acc. to Standard UL 61010-
1, third edition; UL File No.: E228586
Mea suring
Eq ui pm en t
E228586
1.6 Used Symbols
Nr. Symbol Description
1 Direct current: IEC 60417-5031
2 Alternating current: IEC 60417-5032
3 Direct and alternating current: IEC 60417-5033
4 Earth (ground) terminal: IEC 60417-5017
5 Protective conductor terminal: IEC 60417-5019
6 Caution, risk of electric shock
7 Caution, risk of danger: ISO 7000-0434
8
Protective Insulation IEC 60417-5172
Safety Class II devices
9 Guideline 2002/96/EC for electrical and electronic old devices

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 7 von 20
1.7 Exclusion of liability
The contents of this document have been reviewed on their compliance with the
hardware and software described therein. Yet, deviations cannot be excluded, so that
we cannot guarantee full compliance. The specifications in this document are,
however, reviewed at regular intervals. Necessary corrections will be included in the
next edition. You are invited to send us your suggestions for improvement.
1.8 Copyright
Copyright Siemens AG 2018. All rights reserved.
Transmission or reproduction of this document, as well as the use and forwarding of
its contents is not permitted without express written authority. Offenders will be liable
for damages. All rights, including rights created by patent grant or registration of a
utility model or design, are reserved.
Subject to technical changes without notice.

C53000-B1140-C602-1
Seite 8 von 20 Operating Instructions 7XV5810 0xA00
1.9 Operating Instructions
1.10 Scope of Application
The switched mode Wide-range power supply unit has a universal scope of
application due to its extremely wide input voltage range. The power supply unit is
designed for low power consumers (output power up to 3W) that require a mains
buffering time of more than 50ms. The output is short-circuit proof and stable at no
load. The output voltage is monitored and displayed via a pilot LED. If the output
voltage falls short by 10% a relay opens and the LED goes out.
1.11 Description of the functional unit
The Wide-range power supply unit inside its plastic housing is a hardwired and tested
functional unit. It is provided with a clip-on mounting for a DIN EN 50022 top-hat rail
35 mm. Auxiliary power supply, electrical consumer and pilot relay can be safely
connected via the screw-type terminals. The devices are free of silicone and halogen
as well as flame-retardant (UL94-V0).
1.12 In case of a short-circuit
The output of the Wide-range power supply unit is short-circuit proof for an unlimited
amount of time. In case of a short-circuit longer than 5 seconds the device must be
switched off for more than 30 seconds or be operated in open-line operation to be
ready for operation again.
1.13 Switching off the device
After the switching off of the device and the decrease of the GOK relay, the device
must stay off during 3.5 seconds before it can be switched on. If you start the device
before this time range of 3.5 seconds, the device must thus stay off during 5 minutes
before being able to be switched on again.
1.14 Installation
The admissible ambient temperature (operation or functional temperature) is
to be observed (see technical data, chapter 2).
Disregard of the temperature range required for proper function may cause
malfunction and failure of the device
The wide-range power supply unit must be clipped on a 35 mm top-hat rail
(according to DIN EN 50022). It is not admissible to install the device with
screws
A spacing of 100 mm before and after the device respectively must be
observed to allow the cooling of the device with the help of the venting slots.
The devices are permitted only for operation within enclosed housing or
cabinets or the places of installation are to be accessible only for qualified
personnel.

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 9 von 20
1.15 Connection
The connection of the supply voltage is to be carried out according to
VDE0100 and VDE0160. The auxiliary supply of the device is to be provided
with an external disconnector (switch) for the safety isolation of the power
supply and with a safety device (fuse), 2 AT or 4 AT.
Warning
If you use litz wire, please use wire termination.
The external disconnector is to be labelled accordingly. A safety cutout can
possibly act in both functions.
Recommended stripping length: 5 mm.
The output voltage of the power supply conducted to the consumer must be
done with cables that are isolated twice or are separated from the network
cables.
1.16 Commissioning
Check whether the operation data comply with the values on the rating plate.
Do not make any changes at the device.
Clip the wide-range power supply on the top–hat rail with the help of clip-on
mounting.
Connect the auxiliary power to the terminals Vaux (see chapter 2.5 und 0).
The device is ready for use after switching on the auxiliary power.
The green LED `RUN´ lights up.

C53000-B1140-C602-1
Seite 10 von 20 Operating Instructions 7XV5810 0xA00
1.17 Maintenance
The wide-range power supplies require no maintenance. For cleaning, please use a
dry and free of fuzz rag.
Note
Do not use any liquid agents or substances for
cleaning.

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 11 von 20
2 Technical Data
2.1 Power supply 7XV5810 0BA00 (24 V)
Input
Power supply (Vaux) – Direct-current voltage (DC)
24 V to 250 V (±20 %)
Ripple allowed for the DC input voltage 15 %
Power input 12 W
Maximum inrush current at ≤110 V < 15 A
Maximum inrush current at 220 V to
300 V ≤22 A; after 250 µs: < 5 A
Degree of efficiency > 50 % at nominal load
Power supply (Vaux) – Alternative current (AC)
60 V to 230 V (±20 %),
45 Hz to 65 Hz
Higher harmonics allowed 2 kHz
Maximum inrush current at ≤115 V < 15 A
Maximum inrush current at 230 V ≤22 A; after 250 µs: < 5 A
Power input 25 VA
Output
Connection 2-pole terminal
Rated output current Max. 250 mA
Behavior in case of short-circuit: mains
buffering permanent
Power supply failure At least 50 ms at nominal load
Status display of the output voltage 1 green operating LED
Rated output voltage
DC 24 V; Imax = 125 mA
(at Vaux = DC 24 V to 35 V)
DC 24 V; Imax = 250 mA
(at Vaux = DC 35 V to 250 V or AC 60 V
to 230 V)

C53000-B1140-C602-1
Seite 12 von 20 Operating Instructions 7XV5810 0xA00
2.2 Power supply 7XV5810 0CA00 (5 V)
Input
Power supply (Vaux) – Direct-current voltage (DC)
24 V to 250 V (±20 %)
Ripple allowed for the DC input voltage 15 %
Power input 8 W
Maximum inrush current at ≤110 V < 15 A
Maximum inrush current at 220 V to
300 V ≤22 A; after 250 µs: < 5 A
Degree of efficiency > 50 % at nominal load
Power supply (Vaux) – Alternative current (AC)
60 V to 230 V (±20 %),
45 Hz to 65 Hz
Higher harmonics allowed 2 kHz
Maximum inrush current at ≤115 V < 15 A
Maximum inrush current at 230 V ≤22 A; after 250 µs: < 5 A
Power input 12 VA
Output
Connection 2-pole terminal
Rated output current 600 mA
Behavior in case of short-circuit: mains
buffering permanent
Power supply failure At least 50 ms at nominal load
Status display of the output voltage 1 green operating LED
Rated output voltage DC 5 V; Imax = 600 mA

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 13 von 20
2.3 Combined specifications
Environmental conditions (operate only in rooms)
Ambient Temperatures
Temperature recommended during the
operation -5 °C to +55 °C (23 °F to 131 °F)
Temperature during the transport and the
storage -25 °C to +70 °C (-13 °F to 158 °F)
Humidity
mean value per year ≤75 % relative humidity
Maximum value per year 95 % relative humidity on 30 days per
yea
r
Condensation during operation Not allowed
Condensation during transport and
storage Allowed
Other environmental indications
Maximum height over sea level 2000 m
Degree of pollution 2
Class of protection according to IEC
60529 IP 20
Overvoltage category III
Alarm relay
Relay
MSR-Relay, 1 NC (open) contact
Potential free
2-pole connecto
r
Maximum switching voltage (nominal
value): AC 240 V
Maximum switching current 5 A
Maximum switching capability
DC: 50 W at 300 V
DC 270 W at 35 V
A
C 2000 V
A
A
llowed current for contacts 5 A
Fuses
Soldered T2.0 A
Exchangeable T1.6 A / AC 250 V / DC 300 V

C53000-B1140-C602-1
Seite 14 von 20 Operating Instructions 7XV5810 0xA00
Safety
Acc. to DIN EN 61010 Part 1
Overvoltage category
Degree of pollution
Fire stability Class
Acc. to UL 94
III
2
V0
Insulation tests
EN61010
IEC 255-5: ANSI/IEEE C37.90.0
Voltage test (routine test)
- Auxiliary power to fault relay
- Auxiliary power to RS232 interface
- Fault relay to RS232 interface
Surge voltage test (type test)
61010-1 3rd edition
- Auxiliary power to relay
- Auxiliary power to RS232 interface
- Fault relay to RS232 interface
each
DC 5 kV / 1 s (with bypass capacitors)
AC 3,51 kV/50 Hz/1 s
(without bypass capacitors)
each
6,4 kV (peak);
1,2 µs /50 µs; 0,5 J;
3 pos. und 3 neg. surges in
Intervals of 5 s
All circuits, Class III
(not on open contacts)
EMC Tests on interference emission
Standard: EN 50081-1
Conducted interference only power
supply voltage,
CISPR 22, EN 55022
DIN VDE 979 Teil 22
Radio interference field strength
CISPR 11, EN 55011
DIN VDE 0878 Teil 22
150 kHz to 30 MHz
Limit Class A
Limit Class A
30 MHz to 1000 MHz
Limit Class A
Limit Class A

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 15 von 20
EMC tests on interference immunity
IEC 60255-26 (Product standard)
Damped oscillatory waves
IEC 60255-26, IEC 61000-4-18, Class III
VDE 0435 part 303, Class III
Electrostatic discharge (ESD)
IEC 60255-26 Class III
EN 61000-4-2, Class III
Radiated electromagnetic fields,
amplitude modulated
IEC 61000-4-3
Radiated electromagnetic fields,
pulse modulated
IEC 61000-4-3
Fast transient disturbances/Burst
IEC 61000-4-4, Class
IEC 60255-26, Class IV
EN 61000-4-4, Class IV
Fast transient disturbances /Burst
IEC 61000-4-4, Class III
IEC 60255-26, Class III
EN 61000-4-4, Class III
100 kHz and 30 surges per minute;
Test duration 1 minute
2,5 kV longitudinal voltage;
1 kV transverse voltage
6 kV contact discharge
8 kV air discharge,
both polarity; 150 pF;
Ri = 330 Ohm
10 V/m; 80 MHz to 1000MHz;
80% AM; 1 kHz
35 V/m, 900 MHz
Frequency 200 kHz;
Duty cycle 50 % oder Duty cycle 100 %
On power supply input
4 kV; 5/50 ns; 5 kHz;
Burst duration 15 ms
Repetition 300 ms; both polarity;
Ri = 50 Ohm; test duration: 1 min
On signal lines
4 kV; 5/50 ns; 5 kHz;
Burst duration 15 ms above average
Repetition 300 ms; both polarity;
Ri = 50 Ohm; test duration 1 min

C53000-B1140-C602-1
Seite 16 von 20 Operating Instructions 7XV5810 0xA00
Line conducted HF, amplitude modulated
IEC 61000-4-6, EN 61000-6-5
Immunity to power frequency magnetic
field
EN 61000-4-8, Class IV
10 V; 150 kHz to 80 MHz;
80 % AM; 1 kHz
30 A/m, permanent; 300 A/m during 3 s;
50 Hz
Mechanical stress test
Vibration and shock during operation
Vibration
IEC 60068-2-6
IEC 60255-21-1
Shock
IEC 60068-2-27
IEC 60255-21-2, Class 1
Seismic vibration
IEC 60068-3-3
IEC 60255-21-3, Class 2
sinusoidal
5 Hz to 150 Hz
Amplitude;+/- 7,5 mm (under 8 Hz):
acceleration: 20 m/s2(2 g) (beyond 8 Hz)
Frequency sweep rate 3 (each at 90o)
20 cycles per axe
semi-sinusoidal
acceleration 5 g, duration 11 ms,
every 3 shocks in both directions of the
3 axes
sinusoidal
1 Hz to 8 Hz: +8 mm
Amplitude (horizontal axe)
1 Hz to 8 Hz: +4 mm
Amplitude (vertical axe)
8 Hz to 35 Hz: 2g acceleration (horizontal
axe)
8 Hz to 35 Hz: 1g acceleration
(vertical axe)
Frequency sweep rate 1 octave/min
1 cycle in 3 orthogonal axes

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 17 von 20
Vibration and shock during transport
and storage
Vibration
IEC 60068-2-6
IEC 60255-21-1, Class 2
Shock
IEC 60068-2-27
IEC 60255-21-2, Class 1
Shock
IEC 60068-2-29
IEC 60255-21-2, Class 1
sinusoidal
5 Hz to 8 Hz: ± 7,5 mm amplitude;
8 Hz to 150 Hz: 2 g acceleration
Frequency sweep rate 1 octave/min
20 cycles in 3 axes orthogonal
semi-sinusoidal
Acceleration 15 g, duration 11 ms, every
3 shocks in both directions of the 3 axes
semi sinusoidal
Acceleration 10 g, duration 16 ms,
every 1000 shocks in both directions of
the 3 axes

C53000-B1140-C602-1
Seite 18 von 20 Operating Instructions 7XV5810 0xA00
2.4 Dimension Drawings
Figure 1: Dimension Drawings (in mm)

C53000-B1100-C602-1
7XV5810 0xA00 Operating Instructions Seite 19 von 20
2.5 Connection terminals 7XV5810-0BA00 (24 V)
Terminal Description Connection
0V Output voltage VAConsumer ≤6 W
For Vaux = 24 V to 35 V, max. 3 W
24V Output voltage UAConsumer ≤6 W
For Vaux > 35 V, max. 6 W
1 Voltage control relay K1 1 (break contact)
2 Voltage control relay K1 1 (break contact)
L1/L+ Power supply Vau
x
AC: L1 DC: L+
N/L- Power supply Vaux AC: N DC: L-
Table 1: Connection terminals for the 24 V wide-range power supply
2.6 Connection terminals 7XV5810-0CA00 (5 V)
Terminal Description Connection
0V Output voltage V
A
Consumer ≤3 W
5V Output voltage V
A
Consumer ≤3 W
1 Voltage control relay K1 1 (break contact)
2 Voltage control relay K1 1 (break contact)
L1/L+ Power supply Vaux AC: L1 DC: L+
N/L- Power supply Vaux AC: N DC: L-
Table 2: Connection terminals for the 5 V wide-range power supply

C53000-B1140-C602-1
Seite 20 von 20 Operating Instructions 7XV5810 0xA00
2.7 Ordering Data
Name Ordering-Nr.
Wide-range power supply 7 X V 5 8 1 0 - 0 A 0 0
24V B
5V C
Table 3: Ordering Data of the wide-range power supplies