Siemens SITOP PSU6200 User manual

___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SITOP power supply
SITOP PSU6200 1ph
Manual
SITOP PSU6200 12 V/7 A
6EP3323
-7SB00-0AX0
SITOP PSU6200 12 V/12 A
6EP3324
-7SB00-3AX0
SITOP PSU6200 24 V/3.7 A
6EP3333
-7LB00-0AX0
SITOP PSU6200 24 V/5 A
6EP3333
-7SB00-0AX0
SITOP PSU6200 24 V
/10 A
6EP3334
-7SB00-3AX0
SITOP PSU6200 24 V/20 A
6EP3336
-7SB00-3AX0
03.2019
A5E44623264
-1-76
Overview
Notes on safety
1
Description, device design,
dimension drawing
2
Mounting/removal
3
Mounting position, mounting
clearances
4
Installation
5
Technical data
6
Safety, approvals, EMC
7
Ambient conditions
8
Applications
9
Environment
10
Service & Support
11

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E44623264-1-76
Ⓟ
03/2019 Subject to change
Copyright © Siemens AG 2019.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 3
Overview
Figure 1 View of devices
The 1-phase SITOP PSU6200 from the product line is a powerful, regulated standard power
supply for automated machines and systems. In addition to a high efficiency, these low-
profile power supply units have an outstanding overload behavior.
The key benefits of the product include:
●Wide-range input that allows it to be connected to almost any 1-phase line supply around
the world – or to a DC power source
●The output voltage can be set in the range 12 V - 15.5 V or 24 V - 28 V
●Brief overload capability of 150% for 5 s/min (extra power)
●Continuous overload capability of 120% up to an ambient temperature of 45 °C
●Integrated signaling contact for "12 V O.K." or "24 V O.K."
●Push-in connections facilitate fast wiring
●Diagnostic monitor with utilization and service life display using LEDs
●Diagnostics interface to connect to the automation system via only one digital PLC input
●Ambient temperature -25 °C ... 70 °C
●To increase the system availability, these reliable power supplies can be expanded using
SITOP supplementary modules (redundancy module, selectivity module, buffer module),
as well as SITOP DC-UPS modules.

Overview
SITOP PSU6200 1ph
4Manual, 03.2019, A5E44623264-1-76
Ordering data
The following device options are available:
Regulated SITOP PSU6200S power supply
Type
Order number
Input 1 AC 120/230 V,
110 - 240 V DC
Output 12 V DC/7 A
6EP3323-7SB00-0AX0
Input 1 AC 120/230 V,
110 - 240 V DC
Output 12 V DC/12 A
6EP3324-7SB00-3AX0
Input 1 AC 120/230 V,
120 - 240 V DC
Output 24 V DC/3.7 A
6EP3333-7LB00-0AX0
Input 1 AC 120/230 V,
120 - 240 V DC
Output 24 V DC/5 A
6EP3333-7SB00-0AX0
Input 1 AC 120/230 V,
120 - 240 V DC
24 V/10 A DC output
6EP3334-7SB00-3AX0
Input 1 AC 120/230 V,
120 - 240 V DC
24 V/20 A DC output
6EP3336-7SB00-3AX0
Accessories
Type
Order number
Reference labeling plate (160 plates)
6ES7193-6LF30-0AW0

SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 5
Table of contents
Overview.................................................................................................................................................... 3
1 Notes on safety.......................................................................................................................................... 7
2 Description, device design, dimension drawing ......................................................................................... 9
2.1 Device description.....................................................................................................................9
2.2 Connections and terminal designation....................................................................................10
2.3 Potentiometer..........................................................................................................................11
2.4 Status displays and signaling .................................................................................................12
2.5 Operating mode ......................................................................................................................15
2.6 Block diagram .........................................................................................................................16
2.7 Dimensions and weight...........................................................................................................18
3 Mounting/removal .................................................................................................................................... 21
4 Mounting position, mounting clearances.................................................................................................. 23
4.1 Standard mounting position....................................................................................................23
4.2 Other mounting positions........................................................................................................26
4.2.1 6EP3323-7SB00-0AX0 ...........................................................................................................26
4.2.2 6EP3324-7SB00-3AX0 ...........................................................................................................28
4.2.3 6EP3333-7LB00-0AX0 ...........................................................................................................30
4.2.4 6EP3333-7SB00-0AX0 ...........................................................................................................32
4.2.5 6EP3334-7SB00-3AX0 ...........................................................................................................34
4.2.6 6EP3336-7SB00-3AX0 ...........................................................................................................36
5 Installation ............................................................................................................................................... 39
5.1 Line-side connection...............................................................................................................39
5.2 Output-side connection...........................................................................................................41
6 Technical data ......................................................................................................................................... 43
6.1 Input ........................................................................................................................................43
6.2 Output .....................................................................................................................................46
6.3 Efficiency.................................................................................................................................52
6.4 Closed-loop control.................................................................................................................56
6.5 Protection and monitoring.......................................................................................................57
6.6 MTBF ......................................................................................................................................58
6.7 Mechanical system .................................................................................................................59
6.8 Dimension drawing .................................................................................................................60

Table of contents
SITOP PSU6200 1ph
6Manual, 03.2019, A5E44623264-1-76
7 Safety, approvals, EMC ........................................................................................................................... 61
7.1 Safety ..................................................................................................................................... 61
7.2 Test voltage............................................................................................................................ 62
7.3 Approvals ............................................................................................................................... 63
7.4 EMC ....................................................................................................................................... 64
8 Ambient conditions .................................................................................................................................. 65
9 Applications ............................................................................................................................................. 67
9.1 Parallel connection to increase the power rating................................................................... 67
9.2 Overload protection in the 24 V output circuit........................................................................ 69
9.3 Protection against short-time voltage dips............................................................................. 70
9.4 Protecting against longer power failures................................................................................ 71
10 Environment ............................................................................................................................................ 73
11 Service & Support.................................................................................................................................... 75

SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 7
Notes on safety
1
WARNING
Correct handling of the devices
When operating electrical devices, it is inevitable that certain components will carry
dangerous voltages.
Therefore, failure to handle the units properly can result in death or serious physical injury
as well as extensive property damage.
Only appropriately qualified personnel may work on or in the vicinity of this equipment.
Perfect, safe, and reliable operation of this equipment is dependent on proper
transportation, storage, installation and mounting.
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again.
If this instruction is not observed, touching live parts can result in death or serious injury.

Notes on safety
SITOP PSU6200 1ph
8Manual, 03.2019, A5E44623264-1-76

SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 9
Description, device design, dimension drawing
2
2.1 Device description
SITOP PSU6200 is a primary-clocked power supply for connection to a 1-phase AC line
supply and a DC supply. An electronically regulated DC voltage that can be set via a
potentiometer is available at the output of the device. The output of the device is isolated,
no-load proof and short-circuit proof. The LED display indicates the operating status. The
operating state of the device can be processed via the signaling contact.
①
AC/DC input
②
DC output
③
Signaling contact (13, 14)
④
Potentiometer, 12 V - 15.5 V or 24 V - 28 V
⑤
Indicator light, diagnostics monitor (O.K., LOAD)
⑥
DIN rail slider
⑦
Convection
⑧
Clearance above/below
⑨
Diagnostics interface (COM)
⑩
DC voltage level increase (HV)
⑪
Parallel operation (PO)
Figure 2-1 Design

Description, device design, dimension drawing
2.2 Connections and terminal designation
SITOP PSU6200 1ph
10 Manual, 03.2019, A5E44623264-1-76
2.2 Connections and terminal designation
The line input terminals ①can be used to establish the connection to supply voltage. The
output terminals ②are used to connect to the loads to be supplied (see also Section
Installation (Page 39)).
The operating state of the device can be processed via the signaling contact ③(function
and contact rating, see Chapter Status displays and signaling (Page 12)).
Connections and terminal designations
①
Line input L1, N (L2), PE one spring-loaded terminal each
②
Output + 2 spring-loaded terminals
②
Output – 3 spring-loaded terminals
③
Signaling contact 13, 14 one spring-loaded terminal each
*1)
Do not subject the end stop to higher loads
Figure 2-2 Terminal data for 6EP3323-7SB00-0AX0, 6EP3324-7SB00-3AX0, 6EP3333-7LB00-
0AX0, 6EP3333-7SB00-0AX0 and 6EP3334-7SB00-3AX0
*1)
Do not subject the end stop to higher loads
Figure 2-3 Terminal data for 6EP3336-7SB00-3AX0

Description, device design, dimension drawing
2.3 Potentiometer
SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 11
2.3 Potentiometer
The potentiometer ④on the front of the device is used to adjust the output voltage. The
output voltage is set to the rated value at the factory and can be set within certain limits; for
example, to compensate voltage drops across long supply lines to the connected load.
Figure 2-4 Potentiometer
Type
Factory setting
Adjustment range
6EP3323-7SB00-0AX0
6EP3324-7SB00-3AX0
12 V 12 V - 15.5 V
6EP3333-7LB00-0AX0
6EP3333-7SB00-0AX0
6EP3334-7SB00-3AX0
6EP3336-7SB00-3AX0
24 V 24 V - 28 V
NOTICE
Thermal overload possible
When adjusting the output voltage to greater than the rated voltage, the output current must
be derated by 4 %/V (for devices with a rated output voltage of 24 V) and 8 %/V (for
devices with a rated output voltage of 12 V) – or the permissible ambient temperature must
be taken into account with 3 °C/V.
Note
It is only permissible to use an insulated screwdriver when actuating the potentiometer.
For information on actuating the potentiometer (screwdriver, torque), see Connections and
terminal designation (Page 10).

Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU6200 1ph
12 Manual, 03.2019, A5E44623264-1-76
2.4 Status displays and signaling
6EP3323-7SB00-0AX0 (12 V/7 A), 6EP3324-7SB00-3AX0 (12 V/12 A),
6EP3333-7LB00-0AX0 (24 V/3,7 A), 6EP3333-7SB00-0AX0 (24 V/5 A),
6EP3334-7SB00-3AX0 (24 V/10 A), 6EP3336-7SB00-3AX0 (24 V/20 A)
Status display LED green for 12 V O.K. or 24 V O.K.
Yellow LED
Signaling contact (13, 14)
Relay contact (NO contact, contact rating (isolated) 24 V AC/0.1 A; 30 V DC/0.1 A
Device without diagnostics monitor
Figure 2-5 Signaling, signaling contact
Signaling
Signaling contact
6EP3323-7SB00-0AX0 (12 V/7 A)
6EP3333-7LB00-0AX0 (24 V/3.7 A)
6EP3333-7SB00-0AX0 (24 V/5 A)
LED "O.K.":
green:
green flashing (0.5 Hz):
Output voltage Uout > 10 V or
Uout > 11.8 V
shutdown as a result of thermal overload
Output voltage Uout > 20 V or
Uout > 23 V
shutdown as a result of thermal overload
Signaling contact (13, 14)
closed:
Output voltage Uout > 10 V
contact rating: 24 V AC/0.1 A; 30 V DC/0.1 A
NOTICE:
It is not permissible that the signal-
ing contact is connected on the primary side!
Output voltage Uout > 20 V
contact rating 24 V AC/0.1 A; 30 V DC/0.1 A
NOTICE:
It is not permissible that the signal-
ing contact is connected on the primary side!

Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 13
Device with diagnostics monitor
Figure 2-6 Signaling, signaling contact
Signaling contact
6EP3324-7SB00-3AX0 (12 V/12 A)
6EP3334-7SB00-3AX0 (24 V/10 A)
6EP3336-7SB00-3AX0 (24 V/20 A)
LED "O.K.":
green:
green flashing (0.5 Hz):
Output voltage Uout > 10 V or
Uout > 11.8 V
shutdown as a result of thermal overload
Output voltage Uout > 20 V or
Uout > 23 V
shutdown as a result of thermal overload
LED "LOAD":
green:
yellow:
reached service life < 90 %
reached service life ≥ 90 %; Iout rated ≥90 %
reached service life < 90 %
reached service life ≥ 90 %; Iout rated ≥90 %
LEDs above LED "LOAD":
LED 5.1 green:
LEDs 5.1+5.2 green:
LEDs 5.1+5.2+5.3 yellow:
Iout rated 30 - 60 %
Iout rated 60 - 90 %
Iout rated > 90 %
Iout rated 30 - 60 %
Iout rated 60 - 90 %
Iout rated > 90 %
Contact ''COM'' (13, 14):
closed:
(for DIP switch COM = 0)
Output voltage Uout > 10 V
or Uout > 11.8 V; data transfer contact rating
24 V AC/0.1 A; 30 V DC/0.1 A
NOTICE:
It is not permissible that the con-
tact is connected on the primary side!
Output voltage Uout > 20 V
or Uout > 23 V; data transfer contact rating
24 V AC/0.1 A; 30 V DC/0.1 A
NOTICE:
It is not permissible that the con-
tact is connected on the primary side!
Diagnostic monitor display:

Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU6200 1ph
14 Manual, 03.2019, A5E44623264-1-76
Service life < 10 %

Description, device design, dimension drawing
2.5 Operating mode
SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 15
2.5 Operating mode
The selection is made using individual DIP switches (when supplied, these are in the 0
position).
It is only permissible to connect two identical devices in parallel to increase the power by
changing over the output characteristic by switching selector switch PO ⑪to 1
DIP switch
6EP3324-7SB00-3AX0 (12 V/12 A)
6EP3334-7SB00-3AX0 (24 V/10 A)
6EP3336-7SB00-3AX0 (24 V/20 A)
COM ⑨:
Selector switch to toggle between the Uout status display and the communication
0: Display of the output voltage status
1: Internal device parameters are transferred via signaling contact (13, 14) (diagnostics interface)
CAUTION:
It is not permissible that the signaling contact is connected on the primary side!
Contact rating: 24 V AC/0.1 A; 30 V DC/0.1 A
HV ⑩:
Setting, above which value, the "O.K." LED is lit.
0: > 10 V
1: > 11.8 V
Setting, above which the "O.K." LED is lit
0: > 20 V
1: > 23 V
PO ⑪:
Switching over output characteristic 0: Constant output voltage "single operation" 1: Load-de-
pendent output voltage "parallel operation"
Additional information can be found in the documents:
●Diagnostics interface (https://support.industry.siemens.com/cs/ww/en/view/109763467)
●Faceplates and communication blocks
(https://support.industry.siemens.com/cs/ww/en/view/109760217)

Description, device design, dimension drawing
2.6 Block diagram
SITOP PSU6200 1ph
16 Manual, 03.2019, A5E44623264-1-76
2.6 Block diagram
Figure 2-7 Block diagram 3.7/5/7 A

Description, device design, dimension drawing
2.6 Block diagram
SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 17
Figure 2-8 Block diagram 10/12/20 A

Description, device design, dimension drawing
2.7 Dimensions and weight
SITOP PSU6200 1ph
18 Manual, 03.2019, A5E44623264-1-76
2.7 Dimensions and weight
Figure 2-9 Dimension drawing
6EP3323-7SB00-0AX0
6EP3333-7LB00-0AX0
6EP3333-7SB00-0AX0

Description, device design, dimension drawing
2.7 Dimensions and weight
SITOP PSU6200 1ph
Manual, 03.2019, A5E44623264-1-76 19
Figure 2-10 Dimension drawing
6EP3324-7SB00-3AX0
6EP3334-7SB00-3AX0
Figure 2-11 Dimension drawing 6EP3336-7SB00-3AX0

Description, device design, dimension drawing
2.7 Dimensions and weight
SITOP PSU6200 1ph
20 Manual, 03.2019, A5E44623264-1-76
6EP3323-7SB00-0AX0
(12 V/7 A)
6EP3333-7LB00-0AX0
(24 V/3.7 A)
6EP3333-7SB00-0AX0
(24 V/5 A)
6EP3324-7SB00-3AX0
(12 V/12 A)
6EP3334-7SB00-3AX0
(24 V/10 A)
6EP3336-7SB00-3AX0
(24 V/20 A)
Dimensions
(W × H × D) in mm
35 × 135 × 125 45 × 135 × 125 70 × 135 × 155
Weight
Approx. 0.7 kg
Approx. 0.9 kg
Approx. 1.5 kg