Siemens 7SR220 Argus User manual

The copyright and other intellectual property rights in this document, and in any model or article produced from it
(and including any registered or unregistered design rights) are the property of Siemens Protection Devices
Limited. No part of this document shall be reproduced or modified or stored in another form, in any data retrieval
system, without the permission of Siemens Protection Devices Limited, nor shall any model or article be
reproduced from this document unless Siemens Protection Devices Limited consent.
While the information and guidance given in this document is believed to be correct, no liability shall be accepted
for any loss or damage caused by any error or omission, whether such error or omission is the result of
negligence or any other cause. Any and all such liability is disclaimed.
©2011 Siemens Protection Devices Limited
7SR210 Non-Directional Relay
7SR220 Directional Relay
Configuration Guide
(Software Version 2435H85008R7a-7a) (7SR210)
(Software Version 2435H85009R7a-7a) (7SR220)

7SR210 & 7SR220 Configuration Guide
Document Release History
This document is issue 2011/05.
2011/05 First issue
Page 2 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
Contents
Document Release History ...................................................................................................................................... 2
Software Revision History.........................................................................................Error! Bookmark not defined.
Contents .................................................................................................................................................................. 3
Section 1: Introduction ............................................................................................................................................. 5
1.1 Relay Menus And Display ....................................................................................................................... 5
1.2 Operation Guide...................................................................................................................................... 7
1.2.1 User Interface Operation........................................................................................................... 7
Section 1: Configuring the Relay Using Reydisp Evolution.................................................................................... 10
1.1 Physical Connection.............................................................................................................................. 10
1.1.1 Front USB connection............................................................................................................. 10
1.1.2 Standard rear RS485 connection............................................................................................ 11
1.1.3 Optional rear fibre optic connection ........................................................................................ 11
1.1.4 Optional rear RS485 + IRIG-B connection .............................................................................. 12
1.1.5 Optional rear RS232 + IRIG-B connection .............................................................................. 12
1.1.6 Configuring Relay Data Communication ................................................................................. 13
1.1.7 Connecting to the Relay via Reydisp Evolution....................................................................... 14
©2011 Siemens Protection Devices Limited Page 3 of 14

7SR210 & 7SR220 Configuration Guide
List of Figures
Figure 1.1-1 Menu…………………………………………………………………………………………...........................4
Figure 1.1-2 Fascia Contrast Symbol…………………………………………………………….……… .........................4
Figure 1.1-3 Relay Fascia…………………………………………………………….………...........................................5
Figure 1.2-1 Relay Identifier Screen…………………………………………………..………….……......................... …6
Figure 1.2-3 Menu Structure for 7SR21 relay……………………………………..…………….…… ......................... …7
Figure 1.2-4 Menu Structure for 7SR22 relay……………………………………………………...… ......................... …8
Figure 2.1-1 USB connection to a PC……………………………………………….……………….… ..................... …11
Figure 2.1-2 Standard rear RS485 connection to a PC………………………………………….…………………. .. …12
Figure 2.1-3 Additional (Optional) rear fibre optic connection to a PC………………………………………….… .. …12
Figure 2.1-4 Additional (Optional) rear RS485 + IRIG-B connection to a PC………………….…………………. . …13
Figure 2.1-5 Additional (Optional) rear RS232 + IRIG-B connection to a PC…………………………………….……13
Figure 2.1-6 PC Comm Port Selection…………………………………………………………….…......................... …14
Page 4 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
Section 1: Introduction
1.1 Relay Menus And Display
All relay fascias contain the same access keys although the fascias may differ in appearance from model to
model. The basic menu structure is also the same in all products and consists of four main menus, these being,
Settings Mode - allows the user to view and (if allowed via the settings mode password) change settings in the
relay.
Instruments Mode - allows the user to view the relay meters e.g. current, voltage etc.
Fault Data Mode - allows the user to view the type and data of any fault that the relay has detected.
Control Mode - allows the user to control external plant under the relays control for example the CB (if allowed
via the control mode password)
The menus can be viewed via the LCD by pressing the access keys as below,
Figure 1.1-1 Menu Navigation
Pressing CANCEL returns to the Identifier screen
LCD Contrast
To change the contrast on the LCD insert a flat nosed screwdriver into the screwhead below the contrast symbol,
turning the screwhead left or right decreases and increases the contrast of the LCD.
Figure 1.1-2 Fascia Contrast symbol
©2011 Siemens Protection Devices Limited Page 5 of 14

7SR210 & 7SR220 Configuration Guide
Figure 1.1-3 Relay Fascia (Please note fascia may differ from illustration)
Page 6 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
1.2 Operation Guide
1.2.1 User Interface Operation
The basic menu structure flow diagram is shown in Figure 1.2-2. This diagram shows the main modes of display:
Settings Mode, Instrument Mode, Fault Data Mode and Control Mode.
When the relay leaves the factory all data storage areas are cleared and the settings set to default as specified in
settings document.
When the relay is first energised the user is presented with the following message: -
7SR220
_______________________________
ENTER to CONTROL
Figure 1.2-1 Relay Identifier Screen
On the factory default setup the relay LCD should display the relay identifier, on each subsequent power-on the
screen that was showing before the last power-off will be displayed.
The push-buttons on the fascia are used to display and edit the relay settings via the LCD, to display and activate
the control segment of the relay, to display the relays instrumentation and Fault data and to reset the output
relays and LED’s.
The five push-buttons have the following functions:
READ DOWN READ UP
Used to navigate the menu structure.
ENTER
The ENTER push-button is used to initiate and accept setting changes.
When a setting is displayed pressing the ENTER key will enter the edit mode, the setting will flash and can now
be changed using the▲or ▼buttons. When the required value is displayed the ENTER button is pressed again
to accept the change.
When an instrument is displayed pressing ENTER will toggle the instruments favourite screen status.
CANCEL
This push-button is used to return the relay display to its initial status or one level up in the menu structure.
Pressed repeatedly will return to the Relay Identifier screen. It is also used to reject any alterations to a setting
while in the edit mode.
TEST/RESET
This push-button is used to reset the fault indication on the fascia. When on the Relay Identifier screen it also
acts as a lamp test button, when pressed all LEDs will momentarily light up to indicate their correct operation. It is
also moves the cursor right ►when navigating through menus and settings.
©2011 Siemens Protection Devices Limited Page 7 of 14

7SR210 & 7SR220 Configuration Guide
SETTINGS MODE INSTRUMENTS MODE FAULT DATA MODE
SYSTEM CONFIG
FUNCTION CONFIG
CT/VT CONFIG
SUPERVISION
CB FAIL
BROKEN CONDUCTOR
TRIP CCT SUPERVISION
AUTORECLOSE PROT’N
AUTORECLOSE CONFIG
CURRENT PROT’N
PHASE OVERCURRENT
DERIVED E/F
MEASURED E/F
SENSITIVE E/F
RESTRICTED E/F
COLD LOAD
NPS OVERCURRENT
UNDER CURRENT
THERMAL
CONTROL & LOGIC
CIRCUIT BREAKER
QUICK LOGIC
INPUT CONFIG
OUTPUT CONFIG
CB MAINTENANCE
DATA STORAGE
INPUT MATRIX
FUNCTION KEY MATRIX
BINARY INPUT CONFIG
OUTPUT MATRIX
BINARY OUTPUT CONFIG
LED CONFIG
PICKUP CONFIG
CB COUNTERS
I^2T CB WEAR
CONTROL MODE
CB TRAVELLING CLOSE I OPEN
AR : OUT OF SERVICE
AR : TRIP & RECLOSE
AR : TRIP & LOCKOUT
E/F IN
HOTLINE WORKING : OUT
INST PROT'N : IN
IN I OUT
CONFIRM ACTION
CONFIRM ACTION
IN I OUT
IN I OUT
IN I OUT
FAVOURITE METERS
CURRENT METERS
THERMAL METERS
AUTORECLOSE METERS
MAINTENANCE METERS
GENERAL ALARM METERS
BINARY INPUT METERS
BINARY OUTPUT METERS
VIRTUAL METERS
MISCELLANEOUS
7SR22 ARGUS
____________________________
ENTER to CONTROL
NUMBER OF FAULTS
COMMUNICATIONS
MANUAL CLOSE
46IT
46DT
37-1
37-2
INRUSH DETECTOR
GENERAL ALARMS
50-1
51-1
51-2
50-2
51N-1
51N-2
50N-1
50N-2
50G-1
51G-1
51G-2
50G-2
51SEF-1
51SEF-2
50SEF-1
50SEF-2
COMMUNICATION METERS
DEMAND
SEF IN IN I OUT
Figure 1.2-2 Typical Menu Structure for 7SR21 relay
Page 8 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
SETTINGS MODE INSTRUMENTS MODE FAULT DATA MODE
SYSTEM CONFIG
FUNCTION CONFIG
CT/VT CONFIG
PHASE U/O VOLTAGE
NPS OVER VOLTAGE
U/O FREQUENCY
VOLTAGE PROT’N
SUPERVISION
27/59-1
27/59-2
27/59-3
27/59-4
47-1
47-2
59NIT
59NDT
81-1
81-2
81-3
81-4
81-5
81-6
CB FAIL
VT SUPERVISION
CT SUPERVISION
BROKEN CONDUCTOR
TRIP CCT SUPERVISION
AUTORECLOSE PROT’N
AUTORECLOSE CONFIG
CURRENT PROT’N
PHASE OVERCURRENT
51-3
50-1
51N-4
VOLTAGE CONT O/C
DERIVED E/F
MEASURED E/F
51G-3
50G-1
50G-3
SENSITIVE E/F
RESTRICTED E/F
COLD LOAD
NPS OVERCURRENT
UNDER CURRENT
THERMAL
CONTROL & LOGIC
CIRCUIT BREAKER
QUICK LOGIC
INPUT CONFIG
OUTPUT CONFIG
CB MAINTENANCE
DATA STORAGE
INPUT MATRIX
FUNCTION KEY MATRIX
BINARY INPUT CONFIG
OUTPUT MATRIX
BINARY OUTPUT CONFIG
LED CONFIG
PICKUP CONFIG
CB COUNTERS
I^2T CB WEAR
NEUTRAL OVERVOLTAGE
CONTROL MODE
CB TRAVELLING CLOSE I OPEN
AR : OUT OF SERVICE
AR : TRIP & RECLOSE
AR : TRIP & LOCKOUT
E/F IN
HOTLINE WORKING : OUT
INST PROT'N : IN
IN I OUT
CONFIRM ACTIO N
CONFIRM ACTIO N
IN I OUT
IN I OUT
IN I OUT
FAVOURITE METERS
CURRENT METERS
VOLTAGE METERS
FREQUENCY METERS
POWER METERS
ENERGY METERS
THERMAL METERS
AUTORECLOSE METERS
MAINTENANCE METERS
GENERAL ALARM METERS
BINARY INPUT METERS
BINARY OUTPUT METERS
VIRTUAL METERS
COMMUNICATION METERS
7SR22 ARGUS
____________________________
ENTER to CONTROL
NUMBER OF FAULTS
COMMUNICATIONS
MANUAL CLOSE
51-1
51-2
51-4
50-2
50-3
50-4
51N-1
51N-2
51N-3
50N-1
50N-2
50N-3
50N-4
51G-1
51G-2
51G-4
50G-2
50G-4
51SEF-1
51SEF-2
51SEF-3
51SEF-4
50SEF-1
50SEF-2
50SEF-3
50SEF-4
46IT
46DT
37-1
37-2
Vx U/O VOLTAGE
INRUSH DETECTOR
GENERAL ALARMS
DIRECTIONAL METERS
MISCELLANEOUS METERS
FUNCTION KEY CONFIG
DEMAND
SEF IN IN I OUT
Figure 1.2-3 Typical Menu Structure for 7SR22 relay
©2011 Siemens Protection Devices Limited Page 9 of 14

7SR210 & 7SR220 Configuration Guide
Section 1: Configuring the Relay Using Reydisp Evolution
To set the relay using the communication port the user will need the following:-
PC with Reydisp Evolution Installed. (This can be download from our website www.siemens.com/energy and
found under the submenu ‘Software’). This software requires windows 2000-service pack 4 or above, or windows
XP with service pack 2 or above.
1.1 Physical Connection
The relay can be connected to Reydisp Evolution via any of the communication ports on the relay. Suitable
communication Interface cable and converters are required depending which port is being used.
1.1.1 Front USB connection
To connect your pc locally via the front USB port.
Figure 2.1-1 USB connection to a PC
Page 10 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
1.1.2 Standard rear RS485 connection
Figure 2.1-2 Standard rear RS485 connection to a PC
1.1.3 Optional rear fibre optic connection
Figure 2.1-3 Additional (Optional) rear fibre optic connection to a PC
Sigma devices have a 25 pin female D connector with the following pin out.
Pin Function
2 Transmit Data
3 Received Data
4 Request to Send
5 Clear to Send
6 Data set ready
7 Signal Ground
8 Received Line Signal Detector
20 Data Terminal Ready
©2011 Siemens Protection Devices Limited Page 11 of 14

7SR210 & 7SR220 Configuration Guide
1.1.4 Optional rear RS485 + IRIG-B connection
Figure 2.1-4 Additional (Optional) rear RS485 + IRIG-B connection to a PC
1.1.5 Optional rear RS232 + IRIG-B connection
Laptop computer
USB or 9 pin male
D connector
9 way D connector
RS232 cross-over
cable or RS232 to
USB converter
cable
IRIG-B
COM 3
Figure 2.1-5 Additional (Optional) rear RS232 + IRG-B connection to a PC
Pin Function
1 Carrier Direct (CD)
2 Receive Data (RXD)
3 Transmit Data (TXD)
4 Data Terminal Ready (DTR)
5 Signal Ground (GND)
6 Data set ready (DSR)
7 Request to send (RTS)
8 Clear to Send (CTS)
9 Ring Indicator (RI)
Page 12 of 14 ©2011 Siemens Protection Devices Limited

7SR210 & 7SR220 Configuration Guide
©2011 Siemens Protection Devices Limited Page 13 of 14
1.1.6 Configuring Relay Data Communication
Using the keys on the relay fascia scroll down the settings menu’s into the ‘communications’ menu and change
the settings for the communication port used on the relay. All of the below settings may not be available in all
relay types. Reydisp Evolution software uses IEC60870-5-103 protocol to communicate.
COM1 – Standard RS485 Rear Port
COM2 - USB Port
COM3 – Additional (Optional) Rear Connection
COM4 – Additional (Optional) Rear Connection**
Setting name Range Default Units Notes
Station Address
1 – 254 for IEC60870-5-103
0 – 247 for Modbus RTU
0 – 65520 for DNP3.0
0
Address given to relay to
identify that relay from
others which may be using
the same path for
communication as other
relays for example in a fibre
optic hub
COM1-RS485 Protocol OFF, IEC60870-5-103,
MODBUS-RTU, DNP3.0
IEC60870-5-
103 COM1 is the rear mounted RS485 port
COM1-RS485 Baud
Rate
75 110 150 300 600 1200
2400 4800 9600 19200
38400
19200
COM1-RS485 Parity NONE, ODD, EVEN EVEN
COM2-USB Protocol OFF, IEC60870-5-103,
DNP3.0, MODBUS-RTU,
ASCII
IEC60870-5-
103 COM2 is the front USB port
COM2-USB Baud Rate
75 110 150 300 600 1200
2400 4800 9600 19200
38400 57600 115200
230400 460800 921600
Auto detects Auto detects baud rate via
Connection Manager Setting
COM2-USB Parity NONE, ODD, EVEN EVEN
COM3 Protocol OFF, IEC60870-5-103,
MODBUS-RTU, DNP3.0
IEC6-0870-5-
103 COM3 This is an optional rear mounted connection
COM3 Baud Rate 75 110 150 300 600 1200
2400 4800 9600 19200
38400 57600 115200
57600
COM3 Parity NONE, ODD, EVEN EVEN
COM3 Line Idle* LIGHT ON, LIGHT OFF LIGHT OFF
COM3 Data echo* ON, OFF OFF
COM4 Protocol** OFF, IEC60870-5-103,
MODBUS-RTU, DNP3.0 OFF
COM4 This is an optional
rear mounted connection
COM4 Baud Rate** 75 110 150 300 600 1200
2400 4800 9600 19200
38400
19200
COM4 Parity** NONE, OFF, EVEN EVEN
COM4 Line Idle** LIGHT ON, LIGHT OFF LIGHT OFF
COM4 Data echo** ON, OFF OFF
*Not applicable for RS485 or RS232 interface modules.
**Fibre Optic Module only

7SR210 & 7SR220 Configuration Guide
1.1.7 Connecting to the Relay via Reydisp Evolution
When Reydisp Evolution software is running all available communication ports of the PC will automatically be
detected.
On the start page tool bar open up the sub-menu File > Connect.
The ‘Communication Manager’ window will display all available communication ports. With the preferred port
highlighted, select the ‘Properties’ option and ensure the baud rate and parity match that selected in the relay
Data Comms settings. Select ‘Connect’ to initiate the relay-PC connection.
Figure 2.1-6 PC Comm Port Selection
Via the Relay > Set Address > Address set the relay address (1-254) or alternatively search for connected
devices using the Relay > Set Address > Device Map. The relay can now be configured using the Reydisp
Evolution software. Please refer to the Reydisp Evolution Manual for further guidance.
Page 14 of 14 ©2011 Siemens Protection Devices Limited