Siemens TPS3 03 DC User manual

TPS3 03 DC
For DC Photovoltaic Applications
Surge Protective Device
DC Voltage Photovoltaic System Instructions – Do Not Use for AC Voltage Installation
Save These Instructions - This manual contains important instructions that shall be followed
during installation and maintenance of the power system.
User Manual - Canada

• Only qualified licensed electricians should install or service SPDs
• Hazardous voltages exist within SPDs
• SPDs should never be installed or serviced when energized
• Use appropriate safety precautions including Personal Protection Equipment
• Failure to follow these instructions can result in death, serious injury, and/or equipment damage.
• This manual shall be read in entirety prior to installing
Bonding and Grounding Hazard
Verify that the neutral conductor in the service entrance equipment is bonded to ground in accordance with the National
Electrical Code (NEC®) and all applicable codes.
Verify that the neutral terminal (XO) on the secondary side of distribution transformers are grounded to the system ground
in accordance with the NEC® and all applicable codes.
During installation into an electrical system the SPD must not be energized until the electrical system is completely installed,
inspected and tested. All conductors must be connected and functional including the neutral (if required). The voltage
rating of the SPD and system must be verified before energizing the SPD.
Failure to follow these guidelines can lead to abnormally high voltages at the SPD. This may cause the SPD to fail. The
warranty is voided if the SPD is incorrectly installed and/or if the neutral conductor in the service entrance equipment or
downstream of separately derived systems is not bonded to ground in accordance with the NEC®.
Do Not Hi-Pot Test SPDs
Any factory or on-site testing of power distribution equipment that exceeds normal operating voltage such as
high-potential insulation testing, or any other tests where the suppression components will be subjected to higher voltage
than their rated Maximum Continuous Operating Voltage (MCOV) must be conducted with the SPD disconnected from the
power source. For 4-wire systems, the neutral connection at the SPD must also be disconnected prior to performing high-
potential testing and then reconnected after test completion.
Failure to disconnect SPD and associated components during elevated voltage testing will damage the SPD and will void
the warranty.
WARNING - Hazardous Voltage & Shock Hazard
V
Failure to Follow These Instructions Could Result in Death or Serious Injury

Introduction
Presently, there is no dedicated UL standard for higher voltage DC
SPDs. The following TPS3 03 DCs comply with most recent regulatory
actions including UL 1449 Third Edition Listing and compliance to the
UL Certification Requirement Decision (CRD) regarding DC rated SPDs
for Photovoltaic Systems.
UL 1449 certification requires AC voltage specific language, which is
also included below.
Table1
Be aware that photovoltaic systems generate maximum voltage at
coldest temperatures and brightest light. For example, full sunup after
a cool/cold night produces maximum voltage on photovoltaic systems.
The system’s maximum voltage rating should take this into account.
The following graphic on the SPD’s label represents DC voltage:
Thank you for choosing the Siemens TPS3 03 DC Surge Protective
Device (SPD). TPS3 03 DC is a high quality, high energy surge
suppressor designed to protect sensitive equipment from damaging
transient overvoltages. TPS3 03 DC is parallel connected such that
circuit ampacity is unlimited. Proper installation is important to
maximize performance. Please follow steps outlined herein. These
instructions are not intended to replace national or local codes. Follow
all applicable electrical codes to ensure compliance.
UL 1449 Third Edition (Sept 2009), 2008 NEC® Article 285 and CSA
C22.1 (CEC) generated substantial changes regarding AC voltage SPDs.
Range of Input
Operating
Voltage
Maximum Input
Voltage
TPS3M0305 0 – 375V DC 424V DC
TPS3R0305 0 – 750V DC 905V DC
TPS3P0305 0 – 1000V DC 1188V DC
• Read this manual in entirety prior to installing
• Only qualified licensed electricians should install or
service SPDs
• SPDs should never be installed or serviced when
energized or during electrical storms
• Use appropriate safety precautions including Personal
Protection Equipment
• Failure to follow these instructions can result in
death, serious injury, and/or equipment damage
• When used in outdoor applications, customer must
seal the conduit nipple using watertight fittings (not
included) to ensure a watertight connection
WARNING – Risk of Electric Shock

Parts List
1 - TPS3 03 DC suppressor including 3’ (~1m) conductors
1 - Mounting L bracket
1 - 3/4” conduit nut
2 - Panhead mounting screws
1 - Data Sheet
1 - Installation Sheet (this document)
Table2: Specifications
Specifications
Temperature Operating -40oC (-40oF) to 65oC (+149oF)
Temperature Storage -55oC (-67oF) to 65oC (+149oF)
Wire Size & Installation
Torque
8 AWG; 25 lb - in
6 AWG (Ground); 35 lb - in
NEMA 250 Enclosure Rating Type 4X with appropriate
sealing & sealing condulets
Simplified Explanation of Operation
SPDs sense overvoltage and create a momentary short circuit to redirect
harmful surge energy to earth ground. They reset automatically and
wait for the next surge. This is similar to the pressure relief valve on
a water heater: pressure goes up, valve opens to relieve pressure
and then resets. In an electrical system, an SPD senses overvoltage,
shorts temporarily sending energy to ground and then resets. SPDs
are capable of repeating this function thousands of times.
TPS3 03 DC includes internal overcurrent protection
Supplemental overcurrent protection is not required to protect this SPD.
The TPS3 03 DC models listed above have demonstrated 100kA Short
Circuit Current Ratings (SCCR) including leads on DC power systems.
(See UL Label markings on each SPD or see Data Sheet for specs.)
Follow all applicable codes, which generally require that connecting
conductors have overcurrent protection. Based on the SPD’s #8
conductor, we recommend an immediate upstream overcurrent
protection device rated not greater than 40A. A 40A or smaller circuit
breaker or fuse could serve as a disconnect switch and provide NEC®
or CEC imposed short circuit protection to the conductors.
Similar TPS3 03 DC models have demonstrated 200kA Short Circuit
Current Ratings (SCCR) including leads on AC power systems and have
been rated for Type 1 applications (NEC® Article 285).
This device features internal overcurrent and overtemperature
protection that will disconnect effected surge suppression components
at the end of their useful life, but will maintain power to the load – now
unprotected. If this situation is undesirable for the application, follow
these instructions for replacing the device. TPS3 03 DC is ultrasonically
welded closed and contains no user serviceable parts.
Voltage Rating & Application
Before installing SPD, verify by nameplate voltage or model number
that it has the same voltage rating as the power distribution system.
If unsure, call Siemens TPS Tech Support at 1.888.333.3545 before
proceeding. The SPDs specifier or user should be familiar with the
configuration and arrangement of the power distribution system. The
system is defined by how the secondary windings of the transformer
supplying the service entrance main or load are configured. This
includes whether or not the transformer windings are referenced to
earth via a grounding conductor. The system configuration is not based
on how any specific load or equipment is connected to a particular
power distribution system. SPDs should be installed per the distribution
system, not per a load or motor’s wiring connection.
Figure 2: Dimensions and Weight
Figure 3: Mounting options
• 3/4” pipe nipple (conduit nut included)
• Standard 35mm DIN-rail (not included)
L-bracket tightens onto DIN-rail
• Standard flat mounting surface
Attach L-bracket to surface via mounting holes
3.26”3.26”
1.15”
4.13”
3/4”-14
Sized for std 35mm DIN-Rail
3.31”3.57”
Weight: 1.60 lbs
(0.73 kg)
Bracket Mount
for at surfaces
Std. 3/4”-14 Nipple DIN-rail Mount
(rail not incl.)

TPS3 03 DC Installation Instructions
Pre-Plan your installation. You need to accomplish the following:
• Meet all National and Local codes (NEC® Art. 285 address SPDs,
NEC® Art. 690 addresses photovoltaic, Canadian Electric Code,
Part 1)
• Confirm System voltage to SPD voltage
• Mount SPD as close to panel or equipment as possible to keep
leads short (long leads hurt performance substantially)
• Ensure leads are as short and straight as possible, including
ground. If using a breaker, use a breaker position that is close
to the SPD and the panel’s ground
• Make sure system is grounded per NEC® and clear of faults
before energizing SPD (inadvertent system problem may fail SPD)
• Never Hi-Pot test Any SPD (will prematurely fail SPD)
1. Ensure correct SPD; use voltmeter to check voltages as appropriate.
(See Figure 3 for wire-outs)
2. Determine Mounting method (see Figure 2) – weather resistant
equipment may be required
3. Remove power from panel/source. Confirm panel/source is
deenergized.
4. Identify breaker location and SPD location. Position SPD such that
LED is best visible.
5. Mount SPD – weather resistant applications require additional
sealing, o-rings, etc. (see Figure 5)
6. Connect conductors as appropriate - 1000V models require
insulated sleeving, included
(See Figure 4 for wire-outs) – short & straight as possible (see Figure 4)
7. Label or mark conductors as appropriate (ground: green, positive:
red, negative: black)
8. Make sure system is grounded per NEC® or CEC and is clear of
hazards or faults before energizing
9. Energize and confirm proper operation of green LED indicator. Be
aware that LED requires sufficient voltage to operate. Photovoltaic
applications with low light may not generate enough power to
illuminate the LED.
Figure 4: Typical Panel Installation
Figure 5: Sealing o-rings
Figure 6: LEAD LENGTHS
LEADS: SHORT & STRAIGHT
CUT EXCESS; DO NOT COIL OR LOOP
• CUT OFF EXCESS
LENGTH
• DO NOT LOOP OR
COIL
• SHORT &
STRAIGHT
X
Not Good
P
Good
Sealing gasket: two choices
1.) At 3/4" nom. thread: ID is 1.05"
2.) At 0.14" high 'base step': ID is 1.25"
CONDUCTING DIELECTRIC AND/OR
HI-POTENTIAL TESTING WILL CAUSE
INTERNAL DAMAGE TO TPS3 UNIT.
Do not perform dielectric or high potential
tests with the TPS3 unit installed.
CAUTION
V
Hazardous voltage.
Will cause death or serious injury.
Keep Out.
Qualied personnel only.
Disconnect and lock off all power before
working on this equipment.
V DANGER
DC+
red wire DC-
black wire
Ground
green / yellow wire

Normal Operation
Green LED Indicators
Each phase’s LED Indicator illuminates when the SPD is energized
and operating correctly. Every suppression element is monitored and
connected by logic to the LED. Should any suppression element fail,
the green LED will extinguish.
SPDs on Ungrounded Systems
Caution – Ungrounded AC power systems are inherently unstable
and can produce excessively high line-to-ground voltages during
certain fault conditions. During these fault conditions, any electrical
equipment including an SPD, may be subjected to voltages which
exceed their designed ratings. This information is being provided to
the user so that an informed decision can be made before installing
any electrical equipment on an ungrounded power system.
CONDUCTING DIELECTRIC AND/OR
HI-POTENTIAL TESTING WILL CAUSE
INTERNAL DAMAGE TO TPS3 UNIT.
Do not perform dielectric or high potential
tests with the TPS3 unit installed.
CAUTION
V
Hazardous voltage.
Will cause death or serious injury.
Keep Out.
Qualied personnel only.
Disconnect and lock off all power before
working on this equipment.
V DANGER
6

Troubleshooting & Service
Please contact us for any service related issues.
Quality SPDs withstand severe duty and attempt to protect their
load until failure. There are electrical anomalies that SPDs cannot
protect against. These are generally Sustained Overvoltages also
known as Temporary Overvoltages (TOVs). In this context, Sustained
Overvoltages may be only a few cycles. Failed SPDs tend to be
symptoms, not root causes. A failed SPD is usually a sign of other
problems within the electrical distribution system. As a generalization,
the single largest cause of SPD failures is reference to ground issues.
If the SPD shows problems on startup, there is reasonable chance of
bonding/grounding/misapplication issue. This permanently damages
the unit. If not corrected, it will happen again.
Warranty and Customer Service
Limited Warranty
Siemens warrants its DC PV protection products against defective
workmanship and materials for 5 years. Liability is limited to the repair
or replacement of the defective product at Siemens’ option. A Return
Material Authorization number (RA#) must be given by the company
prior to the return of any product. Returned products must be sent
to the factory with the transportation charges prepaid. In addition,
the company also warranties unlimited replacement of modular and
component parts within the warranty period previously described.
The company specifically disclaims all other warranties, expressed or
implied. Additionally, the company is not be responsible for incidental
or consequential damages resulting from any defect in any product or
component thereof.
The sales contract contains the entire obligation of Siemens. This
instruction manual shall not become part of or modify any prior existing
agreement, commitment or relationship.
Technical Support
1.888.333.3545
Prior to calling Siemens TPS3 Technical Support for assistance or ordering
parts, please have the following information available:
TPS3 model number: ________________________________
Manufacture date: _________________________________
Date of Purchase: ___________________________________
Your order number: _______________________________
Return Shipment Address:
Siemens - Attn: RA #___________
14550 58th Street North
Clearwater, FL 33760
7

4.11.13.lh #8441
Siemens Canada Limited
1577 North Service Road East
Oakville, ON L6H 0H6
SPD Hotline: [phone]
[e-mail]
European Authorized Representative
Obelis s.a.
Boulevard Général Wahis 53
1030 Brussels, BELGIUM
Tel: +(32) 2. 732.59.54
Fax: +(32) 2. 732.60.03
E-Mail: [email protected]