SIGMA TEK AO 046 User manual

AO 046
S-DIAS Analog Output Module
Instruction Manual
Date of creation: 06.06.2017
Version date: 26.07.2023
Article number: 20-010-046-E

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2017
SIGMATEK GmbH & Co KG
Translation of the Original Instructions
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or dis-
tributed in any form (print, photocopy, microfilm or in any other process) without the express permission.
We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi-
ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through
use of this handbook.

S-DIAS ANALOG OUTPUT MODULE AO 046
26.07.2023 Page 1
S-DIAS Analog Output Module AO 046
with 4 outputs (voltage/current switchable)
The S-DIAS AO 046 analog output module has four ±10.8 V or
0-21.6 mA analog outputs with a resolution of 16 bits. The analog out-
puts are powered by an external +24 V supply. The analog output sys-
tem is galvanically separated from the potential of the S-DIAS bus.

AO 046 S-DIAS ANALOG OUTPUT MODULE
Page 2 26.07.2023
Contents
1Introduction............................................................................. 5
1.1 Target Group/Purpose of this Operating Manual......................5
1.2 Important Reference Documentation .........................................5
1.3 Contents of Delivery.....................................................................5
2Basic Safety Directives .......................................................... 6
2.1 Symbols Used...............................................................................6
2.2 Disclaimer......................................................................................8
2.3 General Safety Directives ............................................................9
2.4 Software/Training .......................................................................10
3Standards and Directives......................................................11
3.1 Directives.....................................................................................11
3.1.1 EU Conformity Declaration................................................................11
4Type Plate...............................................................................12
5Technical Data .......................................................................13
5.1 Analog Output Voltage Specifications.....................................13
5.2 Output Accuracy Analog Outputs Voltage...............................13
5.3 Analog Output Current Specifications.....................................14
5.4 Output Accuracy Analog Outputs Current...............................14
5.5 Settling Time of the Analog Outputs........................................15
5.6 Electrical Requirements.............................................................16
5.7 Voltage Monitoring External +24 V Supply..............................18

S-DIAS ANALOG OUTPUT MODULE AO 046
26.07.2023 Page 3
5.8 Miscellaneous .............................................................................18
5.9 Environmental Conditions.........................................................18
6Mechanical Dimensions........................................................19
7Connector Layout..................................................................20
7.1 Status LEDs.................................................................................21
7.2 Applicable Connectors...............................................................22
7.3 Label Field...................................................................................23
8Wiring.....................................................................................24
8.1 Wiring Example...........................................................................24
8.2 Note..............................................................................................25
9Assembly/Installation ...........................................................26
9.1 Check Contents of Delivery.......................................................26
9.2 Mounting......................................................................................27
10 Addressing.............................................................................29
11 Transport/Storage.................................................................32
12 Storage...................................................................................32
13 Maintenance...........................................................................33
13.1 Service.........................................................................................33
13.2 Repair...........................................................................................33

AO 046 S-DIAS ANALOG OUTPUT MODULE
Page 4 26.07.2023
14 Disposal..................................................................................33
15 Hardware Class AO046..........................................................34
15.1 General.........................................................................................35
15.2 Analog Outputs [1-4] ..................................................................36
15.3 Time Offset Mode........................................................................38
15.4 Communication Interfaces.........................................................38
15.5 Internal Properties......................................................................39
15.5.1 Time Offset Mode for Analog Outputs...............................................39
15.5.2 Limitations of this Mode.....................................................................39

S-DIAS ANALOG OUTPUT MODULE AO 046
26.07.2023 Page 5
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x AO 046

AO 046 S-DIAS ANALOG OUTPUT MODULE
Page 6 26.07.2023
2 Basic Safety Directives
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the speci-
fied measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the speci-
fied measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the speci-
fied measures are not taken.
To avoid moderate to slight injuries, observe all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.

S-DIAS ANALOG OUTPUT MODULE AO 046
26.07.2023 Page 7
INFORMATION
Information
Provides important information on the product, handling or
relevant sections of the documentation, which require atten-
tion.

AO 046 S-DIAS ANALOG OUTPUT MODULE
Page 8 26.07.2023
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual
is regularly checked and required corrections are included in the sub-
sequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine opera-
tor is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If neces-
sary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product descrip-
tion. It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operat-
ing manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.