Sigma 3-30KHS User manual

Translation of the original operating manual
sb
09/2014
Rev. 1.15 of 08/05/2020
Sigma 3-30KHS; ;
part no. 0701402
Sigma 3-30KHS
from serial no. 146774
Refrigerated Centrifuge
with Heating System
Operating Manual
Please retain for later use!

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
2 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
3 / 91
Translation of the original operating manual, part no. 0701402
© Copyright by
Sigma Laborzentrifugen GmbH
An der Unteren Söse 50
37520 Osterode am Harz
Germany
Tel.: [phone] / 5007-0
Fax: [phone] / 5007-12
Web: www.sigma-zentrifugen.de
E-mail: [e-mail]

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
4 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
Table of contents
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
5 / 91
Translation of the original operating manual, part no. 0701402
1General information.............................................................................................................9
1.1 Importance of the operating manual..................................................................................9
1.2 Intended use.....................................................................................................................9
1.3 Warranty and liability.........................................................................................................9
1.4 Copyright........................................................................................................................10
1.5 Standards and regulations..............................................................................................10
1.6 Scope of supply..............................................................................................................10
2Layout and mode of operation..........................................................................................11
2.1 Layout of the centrifuge ..................................................................................................11
2.1.1 Functional and operating elements............................................................................11
2.1.2 Name plate................................................................................................................12
2.2 Mode of operation...........................................................................................................13
2.2.1 Centrifugation principle..............................................................................................13
2.2.2 Area of application.....................................................................................................13
2.2.2.1 Speed, radius, and relative centrifugal force ......................................................14
2.2.2.2 Density...............................................................................................................14
3Safety..................................................................................................................................15
3.1 Marking of the unit..........................................................................................................15
3.2 Explanation of the symbols and notes.............................................................................16
3.3 Responsibility of the operator..........................................................................................17
3.4 Operating personnel .......................................................................................................17
3.5 Informal safety instructions .............................................................................................17
3.6 Safety instructions ..........................................................................................................18
3.6.1 Electrical safety .........................................................................................................18
3.6.2 Mechanical safety......................................................................................................18
3.6.3 Fire prevention...........................................................................................................19
3.6.4 Chemical and biological safety ..................................................................................19
3.6.5 Safety instructions for centrifugation..........................................................................20
3.6.6 Resistance of plastics................................................................................................20
3.6.7 Safety of rotors and accessories................................................................................21
3.6.7.1 Service life.........................................................................................................21
3.7 Safety devices ................................................................................................................22
3.7.1 Lid lock device...........................................................................................................22
3.7.2 Standstill monitoring system......................................................................................22
3.7.3 System check............................................................................................................22
3.7.4 Earth conductor check...............................................................................................22
3.7.5 Imbalance monitoring system....................................................................................22
3.7.6 Temperature monitoring system ................................................................................22
3.7.7 Rotor monitoring system............................................................................................22
3.8 Measures in the event of hazards and accidents ............................................................23
3.9 Remaining hazards.........................................................................................................23

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
Table of contents
6 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
4Storage and transport ....................................................................................................... 24
4.1 Dimensions and weight...................................................................................................24
4.2 Storage conditions..........................................................................................................24
4.3 Notes on transport..........................................................................................................24
4.4 Packaging.......................................................................................................................25
4.5 Transport safety device...................................................................................................25
5Set-up and connection ...................................................................................................... 26
5.1 Installation site................................................................................................................26
5.2 Power supply..................................................................................................................26
5.2.1 Type of connection ....................................................................................................26
5.2.2 Customer-provided fuses...........................................................................................27
6Using the centrifuge.......................................................................................................... 28
6.1 Initial start-up..................................................................................................................28
6.2 Switching the centrifuge on.............................................................................................28
6.2.1 Opening and closing the lid........................................................................................28
6.2.2 Installation of rotors and accessories.........................................................................29
6.2.2.1 Installation of a standard rotor............................................................................29
6.2.2.2 Installation of a standard angle rotor with a hermetic lid.....................................30
6.2.2.3 Installing a rotor with the g-lock® system ............................................................31
6.2.2.4 Installation of accessories..................................................................................31
6.2.2.5 Adapters ............................................................................................................33
6.2.2.6 Vessels..............................................................................................................33
6.3 Control system "Spincontrol S".......................................................................................34
6.3.1 User interface............................................................................................................34
6.3.2 Manual mode.............................................................................................................35
6.3.2.1 Starting a centrifugation run...............................................................................35
6.3.2.2 Interrupting a centrifugation run .........................................................................35
6.3.2.3 Interrupting a deceleration process....................................................................35
6.3.2.4 Selection, display, and modification of data........................................................35
6.3.2.5 Standard menu ..................................................................................................36
6.3.2.6 Process library menu .........................................................................................42
6.3.2.7 Parameters menu ..............................................................................................43
6.3.2.8 Setup menu .......................................................................................................47
6.3.2.9 Curve menu.......................................................................................................50
6.3.2.10 Help menu .........................................................................................................51
6.3.2.11 Changing the contrast........................................................................................52
6.3.3 Program mode...........................................................................................................52
6.3.3.1 Saving a program...............................................................................................53
6.3.3.2 Loading a program.............................................................................................53
6.3.3.3 Executing a program..........................................................................................54
6.3.3.4 Deleting a program ............................................................................................54
6.3.3.5 Automatic program rotation................................................................................55
6.3.4 Options for data input and output...............................................................................56
6.4 Switching the centrifuge off.............................................................................................56

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
Table of contents
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
7 / 91
Translation of the original operating manual, part no. 0701402
7Malfunctions and error correction....................................................................................57
7.1 General malfunctions......................................................................................................57
7.1.1 Emergency lid release...............................................................................................58
7.2 Table of error codes........................................................................................................59
7.3 Service contact...............................................................................................................60
8Maintenance and service................................................................................................... 61
8.1 Maintenance...................................................................................................................61
8.1.1 Centrifuge..................................................................................................................61
8.1.1.1 Condenser (only refrigerated centrifuges with an air-cooled refrigeration system)
..........................................................................................................................62
8.1.2 Accessories...............................................................................................................62
8.1.2.1 Plastic accessories ............................................................................................63
8.1.3 Rotors, buckets and carriers......................................................................................63
8.1.4 Load bearing bolts.....................................................................................................64
8.1.5 Glass breakage .........................................................................................................65
8.2 Sterilisation and disinfection of the rotor chamber and accessories ................................65
8.2.1 Autoclaving................................................................................................................66
8.3 Service ...........................................................................................................................67
8.4 Return of defective centrifuges or parts ..........................................................................68
9Disposal.............................................................................................................................. 70
9.1 Disposal of the centrifuge ...............................................................................................70
9.2 Disposal of the packaging...............................................................................................70
10 Technical data....................................................................................................................71
10.1 Ambient conditions .........................................................................................................72
10.2 Technical documentation................................................................................................72
11 Appendix............................................................................................................................ 73
11.1 Range of accessories .....................................................................................................73
11.1.1 Rotor radii..................................................................................................................73
11.2 Speed-gravitational-field-diagram ...................................................................................74
11.3 Acceleration and deceleration curves .............................................................................75
11.4 Table of the service life of rotors and accessories...........................................................77
11.5 Resistance data..............................................................................................................78
11.6 EC declaration of conformity...........................................................................................83
11.7 Declaration of conformity –China RoHS 2......................................................................85
12 Index................................................................................................................................... 87

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
Table of contents
8 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
1 General information
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
9 / 91
Translation of the original operating manual, part no. 0701402
Pos: 1/ 100 Sigma/100 B AZ entrifugen Sigma (St andardmodule)/0 10Allg emeine Inform ationen/010 Allgem eine Informatio nen=== ======== ======== ============== ===@ 26\m od_14053189481 31_68.docx @ 191 680 @ 1@ 1
1 General information
Pos: 2/ 100 Sigma/100 B AZ entrifugen Sigma (St andardmodule)/0 10Allg emeine Inform ationen/010-001 0 S tellenwert der Betriebs anleitung-------------------------------------------------------@ 26\mod_140531 8949962_68.docx @ 191694 @ 2 @ 1
1.1 Importance of the operating manual
A fundamental requirement for the safe and trouble-free operation of the
centrifuge is to be familiar with the fundamental safety instructions and all
possible hazards.
The operating manual includes important information concerning the safe
operation of the centrifuge.
This operating manual and, in particular, the notes on safety and hazards
must be observed by all persons operating the centrifuge.
In addition, the local rules and regulations for the prevention of accidents
must be complied with.
Pos: 3/ 010U niversalmodul e/ Leerzeile @ 0\mod_120 2116244500_0.d ocx@ 114 @ @ 1
Pos: 4/ 100 Sigma/100 B AZ entrifugen Sigma (St andardmodule) /010All gemeine Inform ationen/010-002 0 B estimmungsgem äße Verwendung Sig ma-------------------------------------------@2 6\mod_14053189 51312_68.docx @ 191709 @ 2 @ 1
→
1.2 Intended use
Centrifuges are power-driven machines that separate liquids from solid
matter, liquid mixtures, or solid mixtures by centrifugal force. They are
solely intended for this purpose. Any other use beyond this area of
application is regarded as improper use. Sigma Laborzentrifugen GmbH
cannot be held liable for any damage resulting from such improper use.
The intended use also includes
•observation of all the notes and instructions included in the operating
manual and
•compliance with the care, cleaning, and maintenance instructions.
Pos: 5/ 010U niversalmodul e/ Leerzeile @ 0\mod_120 2116244500_0.d ocx@ 114 @ @ 1
Pos: 6/ 100 Sigma/100 B AZ entrifugen Sigma (St andardmodule)/0 10Allg emeine Inform ationen/010-003 0 G ewährleistung un dH aftung--------------------------------------------------@ 26\mod_14 05318955234_68.docx @ 19173 7@ 2 @ 1
→
1.3 Warranty and liability
The warranty and liability are subject to our "General Conditions" that were
distributed to the operator upon the conclusion of the contract.
Warranty and liability claims are excluded if they are due to:
•improper use.
•non-compliance with the safety instructions and hazard warnings in the
operating manual.
•improper installation, start-up, operation, or maintenance of the
centrifuge.
Pos: 7/ 010U niversalmodul e/Seitenwechsel @ 0\mod_1 202116244312_0.d ocx@ 10 5@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
1 General information
10 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
Pos: 8/ 100 Sigma/100 B AZ entrifugen Sigma (St andardmodule)/0 10Allg emeine Inform ationen/010-004 0 Ur heberrecht Sigma -----------------------------------------------------------------@ 26\mod_1405 318956858_68.docx @ 19 1751@ 2 @ 1
→
1.4 Copyright The copyright concerning the operating manual remains with
Sigma Laborzentrifugen GmbH.
The operating manual is solely intended for the operator and their
personnel. It includes instructions and information that must not be
•duplicated,
•distributed, or
•communicated in any other way.
Non-compliance may be prosecuted under criminal law.
Pos: 9/ 010U niversalmodul e/ Leerzeile @ 0\mod_120 2116244500_0.d ocx@ 114 @ @ 1
Pos: 10 /100 Sigma/100 BA Ze ntrifugen Sigma (S tandardmodule)/ 010 Allgemeine Inform ationen/010-00 50 N ormen und Vorschrif ten------------------------------------------------------@26 \mod_140531895820 2_68.docx @ 191765 @ 2 @ 1
→
1.5 Standards and regulations
EC declaration of conformity
(see chapter 11.6 - "EC declaration of conformity")
Pos: 11 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 12 /100 Sigma/110 BA Ze ntrifugen Sigma (Pr ojekte)/3-30KS _3-30KHS/010 Allg emeine Informatio nen/010-0060 Lieferumf ang 3-30KS_3-3 0KHS @ 29\mod_1 405321864287_6 8.docx @ 197869 @ 2 @ 1
1.6 Scope of supply
The centrifuge comprises:
•1 rotor wrench, size 10
Part no. 930 100
•1 hexagon socket wrench, size 5
Part no. 930 051
•1 tube (30 g) heavy-duty grease for load-
bearing bolts
Part no. 71 401
Documentation:
Operating manual incl. EC declaration of conformity
(see chapter 11.6 - "EC declaration of conformity")
Accessories
According to your order, our order confirmation, and your delivery note.
Pos: 13 /010U niversalmodule/A bschnittswechsel @ 0\m od_12021245140 62_0.docx @ 418 @ @ 1
Pos: 14 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
2 Layout and mode of operation
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
11 / 91
Translation of the original operating manual, part no. 0701402
Pos: 15 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/02 0 Aufbau und Wirkungsw eise/020 Aufbau u ndWirk ungsweise== ================================@26\mod _1405318981820_6 8.docx@ 1 91779 @ 1 @ 1
→
2 Layout and mode of operation
Pos: 16 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/02 0 Aufbau und Wirkungsw eise/020-0 010 A ufbau der Zentrifuge----------------------------------------------------@ 26\mod_1 405318982945_68.docx @ 1 91793@ 2 @ 1
→
2.1 Layout of the centrifuge
Pos: 17 /100 Sigma/110 BA Ze ntrifugen Sigma (Pr ojekte)/3-30KS _3-30KHS/020 A ufbau undW irkungsweise /020-0010-00 11Fu nktions- und Bedie nelemente 3-30KHS @ 1 3\mod_13454 54478046_68.docx @ 71372 @ 3 @ 1
2.1.1 Functional and operating elements
1 Lid
2 User interface (see
chapter 6.3.1 - "User
interface")
3 Mains switch
Fig. 1: Total view of the centrifuge
4 Name plate
(see chapter 2.1.2 -
"Name plate")
5 Mains power cable
Fig. 2: Rear view of the centrifuge
Pos: 18 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
2 Layout and mode of operation
12 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
Pos: 19 /100 Sigma/110 BA Ze ntrifugen Sigma (Pr ojekte)/3-30KS _3-30KHS/020 A ufbau undW irkungsweise /020-0010-00 21Typ enschild 3-30 KHS @ 13\mod_134276 6672292_68.docx @ 6 8839 @ 3 @ 1
2.1.2 Name plate
1 Manufacturer
2 Power consumption
3 Max. speed
4 Max. kinetic energy
5 Serial number
6 Part number
7 Type
8 Nominal voltage
9 CE mark in
compliance with the
directive 2006/42/EC
10 Symbol for special
disposal (see chapter
9 - "Disposal")
11 Consult operating
manual
12 Date of manufacture
13 Max. permissible
density
14 Refrigerant data
Fig. 3: Example of a name plate
Pos: 20 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
2 Layout and mode of operation
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
13 / 91
Translation of the original operating manual, part no. 0701402
Pos: 21 /100 Sigma/100 BA Zentrifugen Sig ma(S tandardmod ule)/020 Aufbau und Wirk ungsweise/020- 0020 Wirkungsweis e----------------------------------------------------------@ 26\mod_1405 318984194_68.docx @ 1918 07@ 2 @ 1
→
2.2 Mode of operation
Pos: 22 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/ 020 Aufbau und Wirkungsw eise/020-0 020-0010 Prinzip der Ze ntrifugation @ 26\m od_140531898544 8_68.docx @ 19182 1 @3 @ 1
→
2.2.1 Centrifugation principle
Centrifugation is a process for the separation of heterogeneous mixtures of
substances (suspensions, emulsions, or gas mixtures) into their
components. The mixture of substances, which rotates on a circular path, is
subject to centripetal acceleration that is several times greater than the
gravitational acceleration.
Centrifuges use the mass inertia inside the rotor chamber for separating the
substances. Due to their higher inertia, particles or media with a higher
density travel outwards. In doing so, they displace the components with a
lower density, which in turn travel towards the centre.
The centripetal acceleration of an object inside a centrifuge, as the effect of
centripetal force, depends on the distance between the object and the axis
of rotation as well as on the angular velocity. It increases linearly as a
function of the distance with regard to the axis of rotation and quadratically
as a function of the angular velocity. The bigger the radius in the rotor
chamber is and the higher the speed is, the higher the centripetal
acceleration is. However, the forces acting on the rotor also increase.
Pos: 23 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 24 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/02 0 Aufbau und Wirkungsw eise/020-0 020-0020 Anwendu ngsbereich @ 26\mo d_1405318986763 _68.docx @ 1918 35@ 3 @ 1
Das→
2.2.2 Area of application
Depending on the area of application of the centrifuge and also on the
particle size, solids content, and volume throughput of the mixture of
substances that is to be centrifuged, there are different types of centrifuges.
The areas of application go from household use as a salad spinner or
honey separator up to specialised technical applications in the clinical,
biological, or biochemical context:
•For numerous clinical examinations, cellular material must be separated
from the liquid to be analysed. The normal separation process can be
sped up considerably by using laboratory centrifuges.
•In the metal-working industry, centrifuges are used for separating oil
from metal cuttings. Dairies use centrifuges in order to separate cow’s
milk into cream and low-fat milk.
•Particularly big centrifuges are used in the sugar industry for separating
the syrup from the crystalline sugar.
•Ultracentrifuges are predominantly used in biology and biochemistry in
order to isolate particles, e.g. viruses. They are specifically designed for
high speeds up to 500,000 rpm. The rotor moves in a vacuum in order
to avoid air friction.
Pos: 25 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
2 Layout and mode of operation
14 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
Pos: 26 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/02 0 Aufbau und Wirk ungsweise/020-0 020-0020-0010 Dre hzahl,R adius, Relative Ze ntrifugalbeschl eunigung @ 26\mod _1405318988082 _68.docx @ 191849 @ 4 @ 1
→
2.2.2.1 Speed, radius, and relative centrifugal force
The acceleration g, which the samples are subject to, can be increased by
increasing the radius in the rotor chamber and by increasing the speed.
These three parameters are interdependent and linked with each other via
the following formula:
Relative centrifugal force RCF = 11.18 x 10-6 x r x n2
r = radius in cm
n = speed in rpm
RCF without any dimension
If two values are entered, the third value is determined by way of the stated
formula. If, afterwards, the speed or the radius is changed, the resulting
relative centrifugal force will be recalculated automatically by the control
unit. If the RCF is changed, the speed will be adapted while the specified
radius is maintained.
The speed-gravitational-field-diagram provides an overview of the
relationship between speed, radius, and RCF (see chapter 11.2 - "Speed-
gravitational-field-diagram").
Pos: 27 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 28 /100 Sigma/100 BA Ze ntrifugen Sigma (S tandardmodule)/ 020 Aufbau und Wirk ungsweise/020-0 020-0020-0020 Dicht e @ 26\mod_1405 318989359_68.docx @ 1 91863 @ 4 @ 1
→
2.2.2.2 Density The laboratory centrifuge is suitable for the separation of constituents of
different densities in mixtures with a maximum density of 1.2 g/cm3. All
information concerning the speed of rotors and accessories refers to liquids
with a density corresponding to this specification. If the density is above this
value, the maximum permissible speed of the centrifuge must be reduced
based on the following formula:
n = nmax x
)/2,1( Rho
Rho = density in g/cm3
Pos: 29 /010U niversalmodule/A bschnittswechsel @ 0\m od_12021245140 62_0.docx @ 418 @ @ 1
Pos: 30 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
15 / 91
Translation of the original operating manual, part no. 0701402
Pos: 31 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030 Sic herheit====== ======== ============== ========= ==@ 26\mod _14053190072 54_68.docx @ 191877 @ 1 @ 1
→
3 Safety
Pos: 32 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0010 Beschilderu ng des Geräts neues Typ enschild (außer 2-16K L, 3-16KL, 3-30KS, 4-1 6S) @ 62\mod_1548 831855885_68.docx @ 621378 @ 2 @ 1
→
3.1 Marking of the unit
The following symbols are used for all types of centrifuges manufactured by Sigma:
Dangerous voltage
I
On (Power)
Hot surface
0
Off (Power)
Caution! Risk of bruising
Name plate (see chapter
2.1.2 - "Name plate")
Protective earth (ground)
CE mark in compliance
with the directive
2006/42/EC
Earth (ground)
Do not dispose as part of
domestic waste
g-lock®-System installed
Unplug the mains plug
Arrow indicating the
direction of rotation
GS mark (tested safety;
only for Germany)
4°C Guarantee
NRTL mark (only for the
USA and Canada)
Centrifuge with heating
system
RCM mark
(only for Australia)
Rotor loading information
(see chapter 6.2.2.4 -
"Installation of
accessories")
China RoHS 2 mark
(only for China)

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
16 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
NOTE
Safety indications on the centrifuge must be kept readable at all times. If
necessary, they must be replaced.
NOTE
Not all of the symbols/labels are used for this centrifuge type.
Pos: 33 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 34 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 35 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0020 Symbol- un dHi nweiserklärung en@ 26\mod_14 05319013955_68.do cx @ 191947 @ 2 @ 1
→
3.2 Explanation of the symbols and notes
In this operating manual, the following names and symbols to indicate
hazards are used:
DANGER
This symbol stands for a direct hazard to the life and health of persons.
Non-observance of these symbols causes serious health problems up to
life-endangering injuries.
DANGER
This symbol stands for a direct hazard to the life and health of persons
due to electrical voltage.
Non-observance of these symbols causes serious health problems up to
life-endangering injuries.
WARNING
This symbol stands for a potential hazard to the life and health of
persons.
Non-observance of these symbols can cause serious health problems up
to life-endangering injuries.
CAUTION
This symbol indicates a potentially hazardous situation
Non-observance of these notes can cause minor injuries or damage to
property.
NOTE
This symbol indicates important information.
Pos: 36 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
17 / 91
Translation of the original operating manual, part no. 0701402
Pos: 37 /100 Sigma/100 BA Zentrifugen Sig ma(S tandardmod ule)/030 Sicherheit/0 30-0030 Verantw ortung des Betreibers @ 26\mod_14 05319015364_68.do cx @1 91961 @ 2 @ 1
→
3.3 Responsibility of the operator
The operator is responsible for authorising only qualified personnel to work
on the centrifuge (see chapter 3.4 - "Operating personnel").
The areas of responsibility of the personnel concerning the operation,
maintenance, and care of the unit must be clearly defined.
The safety-conscious work of the personnel in compliance with the
operating manual and the relevant EC and national health and safety
regulations as well as with the accident prevention regulations must be
checked at regular intervals (e.g. every month).
Under the international rules for health and safety at work, the operator is
obliged to:
•take measures in order to prevent all danger to life or health during
work.
•ensure that centrifuges are operated properly and entirely as intended
(see chapter 1.2 - "Intended use").
•take protective measures against fire and explosion when working with
hazardous substances.
•take measures for the safe opening of centrifuges.
The operator must perform a risk assessment concerning potential
accidents in connection with the centrifuge and take design-related
countermeasures, if necessary.
The centrifuge has to be maintained regularly (see chapter 8 -
"Maintenance and service").
Components that are not in a perfect state must be replaced immediately.
Pos: 38 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 39 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0040 Bedienpers onal @ 26\mod_140 5319017634_6 8.docx@ 191989 @ 2 @ 1
→
3.4 Operating personnel
Persons operating the unit must
•be familiar with the fundamental regulations concerning workplace
safety and accident prevention
•have read and understood this operating manual (and in particular the
safety sections and warning notes) and confirmed this with their
signature.
Pos: 40 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 41 /100 Sigma/100 BA Ze ntrifugen Sigma (S tandardmodule)/ 030 Sicherheit/03 0-0050 Informelle Sic herheitshinweise @ 2 6\mod_14053190 19966_68.docx @ 19 2017 @ 2 @ 1
→
3.5 Informal safety instructions
•This operating manual is a part of the product.
•The operating manual must be kept at the location of use of the
centrifuge. Ensure that it is accessible at all times.
•The operating manual must be handed over to any subsequent owner
or operator of the centrifuge.
•Any changes, additions or updates received must be added to the
operating manual.
•In addition to the operating manual, the general and local rules and
regulations concerning the prevention of accidents and the protection of
the environment must also be supplied.
•Safety and danger indications on the centrifuge must be kept readable
at all times. If necessary, they must be replaced.
Pos: 42 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
18 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
Pos: 43 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/03 0-0060 Sicherheits hinweise-------------------------------------------------------------@ 26\mod_1405 319021480_68.docx @ 1920 31@ 2 @ 1
→
3.6 Safety instructions
Pos: 44 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0060-0010 Elektri sche Sicherheit @ 67\m od_15694746 63546_68.docx @ 716 977 @ 3@ 1
3.6.1 Electrical safety
To reduce the risk of electrical shock, the centrifuge uses a three-wire
electrical cord and plug to connect the equipment to earth-ground. To
preserve this safety feature:
DANGER
•Ensure that the wall socket is properly wired and grounded.
•Check that the mains voltage agrees with the nominal voltage listed on
the name plate.
•Do not place vessels containing liquid on the centrifuge lid or within
the safety distance of 30 cm around the centrifuge. Spilled liquids may
get into the centrifuge and damage electrical or mechanical
components.
•Only qualified and specialised personnel are authorised to perform
service tasks or repairs of the electrical system for which the housing
needs to be removed.
•Inspect the electrical equipment of the unit regularly. Defects such as
loose or burnt cables must be eliminated immediately.
•Following the completion of any type of repair or service, the qualified
and specialised personnel must perform final inspection and testing in
compliance with the relevant standards.
Pos: 45 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 46 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0060-0020 M echanische Sicher heit( außer 1-16/1-1 6K/1-7) @ 26\mod_14 05319024314_68. docx @ 192059 @ 3 @ 1
→
3.6.2 Mechanical safety
In order to ensure the safe operation of the centrifuge, observe the
following:
WARNING
•Do not open the lid when the rotor is in motion!
•Do not reach into the rotor chamber when the rotor is in motion!
•Do not use the centrifuge if it was installed incorrectly.
•Do not use the centrifuge without panels.
•Do not use the centrifuge if the rotors and inserts show signs of
corrosion or other defects.
•Only use the centrifuge with rotors and accessories that have been
approved by the manufacturer. In case of doubt, contact the
manufacturer (see chapter 7.3 - "Service contact").
•Do not hold your fingers between the lid and the housing when closing
the lid. Risk of crushing!
•Defective lid relieving devices could cause the centrifuge lid to fall
(contact the service department, if necessary). Risk of crushing!
•Do not hit or move the centrifuge during its operation.
•Do not lean against or rest on the centrifuge during its operation.
•Do not spin any substances that could damage the material of the
rotors and buckets of the centrifuge in any way. Highly corrosive
substances, for example, damage the material and affect the
mechanical strength of the rotors and buckets.
•Stop the centrifuge immediately in the event of a malfunction.
Eliminate the malfunction (see chapter 7 - "Malfunctions and error
correction") or inform the service department of the manufacturer (see
chapter 7.3 - "Service contact").

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
19 / 91
Translation of the original operating manual, part no. 0701402
WARNING
•Ensure that all repairs are performed only by authorised and
specialised personnel.
•Prior to any start-up, check the centrifuge, rotor, and accessories for
signs of damage that can be discerned from the outside. Special
attention must be paid to all of the rubber parts (e.g. motor cover, lid
seal, and adapters) in terms of visible structural changes. Defective
parts must be replaced immediately.
•Open the centrifuge when it is not in use so that moisture can
evaporate.
Pos: 47 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 48 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0060-0030 Brand schutz thermisch eSi cherungen @ 26\mo d_140531902569 8_68.docx @ 192073 @ 3 @ 1
→
3.6.3 Fire prevention
DANGER
•Do not spin explosive or inflammable substances.
•Do not use the centrifuge within hazardous locations.
Pos: 49 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 50 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/03 0-0060-0040 Ch emische und biologisc heSic herheit @ 26\mod_ 1405319028141_ 68.docx @ 192101 @ 3 @ 1
→
3.6.4 Chemical and biological safety
If pathogenic, toxic, or radioactive samples are intended to be used in the
centrifuge, it is in the responsibility of the user to ensure that all necessary
safety regulations, guidelines, precautions, and practices are adhered to
accordingly.
DANGER
•Infectious, toxic, pathogenic, and radioactive substances may only be
used in special, certified containment systems with a bio-seal in order
to prevent the material from being released.
•Take suitable precautions for your own safety if there is a risk of toxic,
radioactive, or pathogenic contamination
•Materials that chemically react with each other with a high level of
energy are prohibited.
WARNING
•Keep informed about local measures to avoid harmful emissions
(depending on the substances to be centrifuged).
•Protective clothing is not required for the operation of the centrifuge.
The materials to be centrifuged may, however, require special safety
measures (e.g. centrifugation of infectious, toxic, radioactive, or
pathogenic substances).
Pos: 51 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1

Refrigerated Centrifuge with Heating System Sigma 3-30KHS
3 Safety
20 / 91
Version 09/2014, Rev. 1.15 of 08/05/2020 • sb
Translation of the original operating manual, part no. 0701402
Pos: 52 /100 Sigma/100 BA Ze ntrifugen Sigma (Sta ndardmodule)/03 0 Sicherheit/030- 0060-0050 Sicherh eitshinweise zur Z entrifugation @ 26\mo d_1405319029 632_68.docx @ 19211 5@ 3 @ 1
→
3.6.5 Safety instructions for centrifugation
For safe operation, observe the following before starting the centrifuge:
WARNING
•Ensure that the centrifuge was set up properly (see chapter 5 - "Set-up
and connection").
•Maintain a safety distance of at least 30 cm (12 inches) around the
centrifuge.
•Do not store any dangerous goods in the centrifuge area.
•Do not stay in the safety area longer than what is absolutely necessary
for the operation of the centrifuge.
•Only use the centrifuge with rotors and accessories that have been
approved by the manufacturer. We explicitly warn against the use of
equipment of poor quality. Breaking glass or bursting vessels can
cause dangerous imbalances at high speeds
•Ensure that rotor and buckets are correctly fitted (see chapter 6.2.2.1 -
"Installation of a standard rotor").
•Observe the instructions on the installation of accessories (see
chapter 6.2.2.4 - "Installation of accessories").
WARNING
•The rotor must be loaded in a rotationally symmetrical manner at equal
weights.
•If liquids with a density > 1.2 g/cm3are used, reduce the speed (see
chapter 2.2.2.2 - "Density").
•Do not use the centrifuge if the rotor is loaded asymmetrically.
•Do not use the centrifuge with tubes that are excessively long.
Pos: 53 /010U niversalmodule/ Leerzeile @ 0\mod_ 1202116244500_ 0.docx@ 1 14@ @ 1
Pos: 54 /100 Sigma/100 BA Zentrifugen Sig ma(S tandardmod ule)/030 Sicherheit/0 30-0060-0060 Be ständigkeit von Kuns tstoffen @ 26\mod_ 1405319031161_ 68.docx @ 192129 @ 3 @ 1
→
3.6.6 Resistance of plastics
Chemical influences have a strong effect on the polymeric chains of
plastics, and, therefore, on their physical properties. Plastic parts can be
damaged if solvents, acids, or alkaline solutions are used.
NOTE
•Refer to the resistance data (see chapter 11.5 - "Resistance data")!
Pos: 55 /010U niversalmodule/S eitenwechsel @ 0\mod_ 1202116244312_ 0.docx@ 1 05@ @ 1