SIIG JU-EX0111-S1 User manual

1
USB 2.0 4-Port Extender
Quick Installation Guide
04-0877A
Introduction
The USB 2.0 4-Port Extender, using inexpensive CATx
cabling, extends the distance to four USB devices up to 80
meters.
Features and Benefits
• ExtendsUSBdistanceupto80metersviaCATx
cable
• Connect up to 4 USB devices
• Supports high-speed USB 2.0 devices and
backward support for USB 1.1 devices
• Supports USB 2.0 data transfer rate up to
480Mb/s
• The extender requires no additional driver
installation
• Supports hot-swap & Plug-and-Play
System Requirement
• Notebook or Desktop PC with an available USB
port

2
Package Contents
•USB Extender 4-Port Extender-Transmitter
•USB Extender 4-Port Extender- Receiver
• USB 2.0 type A (M) to Type A (M) cable
• Power adapter
• Housing rubber pads (8)
• Quick installation guide
Layout
Transmitter
Figure 1: Front Panel
•OUTPUT UTP/STP: PlugyourCATxcableintothis
port, up to 80 meters maximum
•Power LED: On when the Transmitter is powered
on
OUTPUT
UTP/STP PowerLED

3
Figure 2: Rear Panel
•DC 5V: Connects to the included Power Adapter.
Note: This connection is optional and only needed
when your USB devices are not detected by the
Receiver.
•USB Input: Connects to an available USB 2.0 port on
your computer using the included USB 2.0 Type A
to Type A cable
•EQ: Press the EQ button to adjust for the length of
the CATx cable
Receiver
DC5V USBInput EQ
Figure 3: Front Panel
•Type A USB port: Plug your USB device(s) into
these ports
PowerLED
Type A USB Port

4
Figure 4: Rear Panel
•DC 5V: Connects to the included 5V DC power
adapter
•OUTPUT UTP/STP: Plugyour CATx cable into this
port, up to 80 meters maximum
•EQ: Press the EQ button to adjust for the length of
the CATx cable
Hardware Installation
1. Connect your CATx cable to the OUTPUT UTP/
STP port of the Transmitter and the Receiver.
2. Plug your USB device(s) into the Receiver's Type A
USB port.
3. Plug the included USB 2.0 Type A to Type A cable
into theTransmitter's USB Inputport, then plug the
other end into your computer.
EQ
DC5V
OUTPUT
UTP/STP
•Power LED: On when the Transmitter is powered
on

5
Figure 5
• Both A & B are off: The extension distance is under
60 meters
• A is on and B is off: The extension distance is 60 to
70 meters
• Both A & B are on: The extension distance is 70 to
80 meters
AB
4. Plug the power adapter to the Receiver's 5V DC
power jack. The extender is ready for use.
Transmission Distance Adjustment
Push the EQ button on both Transmitter and Receiver to
adjust for the length of the CATx cable.

6
Application
Desktop or
notebookPC
Transmitter
Receiver
USB
cable
USB
cable
USBdevice(printer,HDDdocking,USB
capture cable, etc)
Figure 6
CATx
cable

7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty covers
the original purchaser and guarantees the product to be free of any defects in materials
or workmanship for three (3) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. Please see our web site for more warranty
details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT
REPLACEMENT to submit a request to SIIG RMA or fax a request to 510-657-5962.
Your RMA request will be processed, if the product is determined to be defective,
an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a
product returned without an RMA number posted on the outside of the
shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.

PRODUCTNAME
USB 2.0 4-Port Extender
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty. High
quality control standards are evident by the overall ease of installation and
compatibility of our products, as well as one of the lowest defective return
rates in the industry. SIIG products can be found in computer retail stores,
mail order catalogs, through major distributors, system integrators, and
VARs in the Americas and the UK, and through e-commerce sites.
USB 2.0 4-Port Extender is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarks of SIIG, Inc. All other names used in this publication are for identification
only and may be trademarks of their respective owners.
May, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.