SIIG AV-GM0513-S1 User manual

1x2 DVI Splitter
P/N: AV-GM0513-S1

Safety and Notice
The AV-GM0513-S1 1x2 DVI Splitter has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic
equipments, the AV-GM0513-S1 should be used with care. Please read and follow the safety
instructions to protect yourself from possible injury and to minimize the risk of damage to the
unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
TABLE OF CONTENTS
INTRODUCTION.................................................................................................................1
FEATURES.........................................................................................................................1
PACKAGE CONTENTS......................................................................................................1
SPECIFICATIONS..............................................................................................................2
PANEL DESCRIPTIONS.....................................................................................................3
HARDWARE INSTALLATION.............................................................................................5
CONNECTION DIAGRAM ..................................................................................................5
WARRANTY .......................................................................................................................6

1
INTRODUCTION
The AV-GM0513-S1 1x2 DVI Splitter receives and reconstructs (equalizing & reclocking) a DVI
signal and distributes it to two identical outputs. It can be perfectly cascaded with one another in
order to obtain more DVI outputs. It will also process (read & store) the EDID information sent
through the Data Display Channel (DDC).
FEATURES
●Perfectly as a repeater by regenerating the DVI signal
●Stackable, 8 devices stacked can support up to 17 outputs
●Reads and remembers the EDID of displays
●Can be modified EQ with two modes
●Extends greater than 14m / 45ft of input / output DVI cable
PACKAGE CONTENTS
●1x AV-GM0513-S1
●1x 1x 5V DC power adapter
●1x User Manual

2
SPECIFICATIONS
Model Name
AV-GM0503-S1
Technical
Role of usage
1x3 Distribution Amplifier (Splitter)
DVI compliance
DVI 1.0
Video support
Up to WUXGA [1920x1200@60Hz] & UXGA [1600x1200@60Hz]
PCB stack-up
4-layer board [impedance control —differential 100Ω; single 50Ω]
Input
1x DVI-I
Output
2x DVI-I
DVI connector
DVI-I [29-pin male, digital only]
RJ45 connector
N/A
Control Switch
2-pin DIP switch
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model
120 x 92 x 26mm [4.7” x 3.6” x 1”]
Package
270 x 175 x 80mm [10.6” x 6.9” x 3.1”]
Weight
Model
353g [12.5oz]
Package
645g [1.4 lbs]
Power supply
5V 2A DC
Power consumption
4 Watt [max]
Operation temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]

3
PANEL DESCRIPTIONS
Front Panel
1. DVI: DVI output 1
2. DVI: DVI output 2
Rear Panel
3. Power: +5V DC
4. DVI: DVI input
5. Rotary switch: ID switch
6. LED: Power indicator
7. LED: Signal indicator

4
Rotary Switch
EDID Mode
0
Default EDID –1920x1200
1
Default EDID –1920x1080
2
Default EDID –1680x1050
3
Default EDID –1600x900
4
Default EDID –1440x900
5
Default EDID –1360x768
6
Default EDID –1280x800
7
EDID Learning [from Output1]
If you cannot boot your computer from the connected AV-GM0513-S1 due to the damaged
EDID in the AV-GM0513-S1, please proceed the “Writing default EDID” and then “Recording
EDID of the connected display”. This will enforce the AV-GM0513-S1 to write the EDID from
display.
Don’t plug in DVI source while the AV-GM0513-S1 is writing default EDID
or recording EDID from displays. This will cause damage to the EDID in the
flash memory.
WARNING!!

5
HARDWARE INSTALLATION
●We suggest you connect the monitor with the lowest resolution support to the DVI-OUT 1.
e.g. Suppose monitor A might support a maximum resolution of 1920 x 1200, monitor B
supports a maximum resolution of 1280 x 1024 and monitor C supports a maximum
resolution of 1024 x 768, please connect monitor C to DVI-OUT 1.
●Unless you would like to use the default universal EDID, please set Rotary Switch at 7, which
allows the AV-GM0513-S1 to read the first connected monitor's EDID.
1. Connect a monitor, a projector or other displays with DVI inputs by a male-to-male DVI cable to
DVI-OUT 1.
2. Power on AV-GM0513-S1 and then turn the rotary switch from any other default EDID to 7.
3. The green signal will start to twinkle.
4. After the twinkling is finished, the EDID Learning is done.
CONNECTION DIAGRAM

6
WARRANTY
The SELLER warrants the AV-GM0513-S1 1x2 DVI Splitter free from defects in the material and
workmanship for 3 years from the date of purchase from the SELLER or an authorized dealer.
Should this product fail to be in good working order within 3 years warranty period, The SELLER, at
its option, repair or replace the unit, provided that the unit has not been subjected to accident,
disaster, abuse or any unauthorized modifications including static discharge and power surge. This
warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if
the warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of
parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day
of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or
assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted
without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without
limitations, any other implied warranty or fitness or merchantability for any particular purpose, all
of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are
responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to
a 30 day warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However,
The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual.
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages
resulting from any defect or omission in this manual, even if advised of the possibility of such
damages. Also, the technical information contained herein regarding the AV-GM0513-S1 features
and specifications is subject to change without further notice.
April, 2018
Support
For more info or tech support
http://www.siig.com/support