Sime Planet dewy 60 bfr User manual

PLANET DEWY

60-100 BFR

User instructions

UK PLEASE LEAVE THIS INSTRUCTION

WITH THE USER

All descriptions and illustrations provided in this manual have been carefully prepared but we reserve the right to make changes

and improvements in our products that may affect the accuracy of the information contained in this manual.

The Benchmark Scheme

Sime Ltd is a licensed member of the Benchmark Scheme which aims to improve the standards of installation and

commissioning of domestic heating and hot water systems in the UK and to encourage regular servicing to optimi-

se safety, efficiency and performance.

Benchmark is managed and promoted by the Heating and Hotwater Industry Council.

For more information visit www.centralheating.co.uk

IPX4D

Planet Dewy 60 BFR: Gas Council number 41-283-03 Planet Dewy 100 BFR: Gas Council number 47-283-11

These appliances comply with the S.E.D.B.U.K. scheme, band “A”

OPERATING INSTRUCTIONS FOR THE USER

1 LIGHTING AHD OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pag. 4

1.1 BOILER IGNITION

1.2 BOILER SHUTDOWN

1.3 TEMPERATURE ADJUSTMENT (WITHOUT LOGICA)

1.4 GAS CONVERSION

1.5 CLEANING AND MAINTENANCE

1.6 MALFUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pag. 5

2 LOGICA REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pag. 6

CONTENTS

VERY IMPORTANT!

60 BFR boiler only

PLEASE MAKE SURE YOUR BENCHMARK CHECKLIST IN THE

INSTALLATION GUIDE, IS FILLED IN CORRECTLY.

ALL GAS SAFE REGISTER INSTALLERS CARRY A ID CARD.

THE REGISTRATION NUMBER SHOULD BE

RECORDED ON THE CHECK LIST.

YOU CAN CHECK YOUR INSTALLER IS GAS SAFE

REGISTERED BY CALLING ON 0800 408 5577

1.1 BOILER IGNITION (fig. 1)

Open the gas isolation valve, lower the con-

trol cover and turn on the boiler by rotating

the selector knob to winter ( ).

The green led ( ) turn on to indicate that

power is on. The boiler, once the tempera-

ture set on the potentiometer is reached,

will start automatically modulate to provide

the system with the required output.

1.2 BOILER SHUTDOWN (fig. 1)

To turn OFF the boiler, turn the selector

knob to (OFF). For prolonged periods of

disuse, disconnect the power supply, close

the gas tap and, in the event of low tempe-

ratures, empty the boiler and hydraulic

system to prevent frost damaged.

1.3 TEMPERATURE ADJUSTMENT

(WITHOUT LOGICA) (fig. 2)

Heating temperature is adjusted using the

heating knob ( ). The set temperature is

indicated on the red led scale from 35 -

80°C and the yellow heating led ( ) turns

on simultaneously. If the water return tem-

perature is lower than about 55° C, combu-

stion product condensates further increa-

sing heat exchange efficiency. Unless a

domestic hot water cylinder is connected,

the DHW control knob has no function.

1.4 GAS CONVERSION

Should it be necessary to convert the

appliance to a different gas from the one

for which the boiler has been equipped,

seek advice from a qualified technician.

1.5 CLEANING AND MAINTENANCE

Preventive maintenance and checking of

the efficient operation of the equipment

and safety devices must be carried out

exclusively by the authorized technical

staff. Should any component require

replacement, only manufacturers original

parts must be used.

WARNINGS

– In case of fault and/or incorrect equipment operation, turn the boiler off. Contact an authorised technician.

– The installation of the boiler and any servicing or maintenance must be carried out by qualified personnel. Under no

circumstances must the devices sealed by the manufacturer be tampered with.

– Any ventilation or air intake grills to the room where the boiler is installed must be kept open and unobstructed.

1 LIGHTING AND OPERATION

APRE

SPIA VERDE

Fig. 1

SPIA GIALLASPIA ROSSA

Fig. 2

OPEN

GREEN LED

RED LED YELLOW LED

OPERATING INSTRUCTIONS FOR THE USER

1.6 MALFUNCTIONS

–Ignition lockout (fig. 3)

If the burner does not light the red led

( ) turns on. To attempt ignition again,

rotate the selector knob to ( ) and

release it immediately returning it to win-

ter position ( ).

If the problem persists, contact a

authorised engineer .

–Insufficient water pressure (fig. 4)

If the “0.5 bar” red light blinks, the boiler

does not work.

To restore operations, fill the system

until the green “1 bar” led turns on.

If all leds are off, request an authorised

engineer.

–Safety/exhaust thermostat

triggered (fig. 5)

If the safety/exhaust thermostat trig-

gers the red “35°C” led blinks. To

attempt ignition again, rotate the selec-

tor knob to ( ) and release it immedia-

tely returning it to winter position ( ).

If the problem persists, contact an

authorised engineer.

–Other faults (fig. 6)

When one of the red “40-80°C” leds

blinks, turn off the boiler and attempt

ignition again.

This operation can be repeated 2-3

times at most, in the event of failure,

request an authorised engineer.

SPIA ROSSA INTERMITTENTE

Fig. 6

SPIA ROSSA

Fig. 3

Fig. 4

SPIA ROSSA INTERMITTENTE

IN CONDIZIONE DI SICUREZZA

SPIA ROSSA INTERMITTENTE

Fig. 5

RED LED

FLASHING RED LED

IN SAFETY CONDITION

FLASHING RED LED

When the boiler is connected to the “Logi-

ca Remote Control” regulator, the selector

CR/OFF/SUM/WIN/UNBLOCK must be

placed in the position ( ); the knobs of the

hot-water service heating potentiometers

do not have any effect and all of the func-

tions will be managed by the regulator (fig.

7). If the “Logica Remote Control” fails, the

boiler will function by placing the selector

on the ( o ), position, obviously

without consequent control of the room

temperature.

The operating instructions are located insi-

de the cover (fig. 8). Each setting or modifi-

cation is displayed (fig. 9).

2 LOGICA REMOTE CONTROL

KEY

1 Display

2 Info button

3 Operating mode button: automatic operation

4 Operating mode button: manual operation

5 Operating mode button: availability

6 Cover with instruction compartment

7 Temperature knob

8 Presence button Fig. 8

KEY

1 Display, time

2 Heating programme

3 Unit (% / C°)

4 Presence button display

5 External temperature

6 Outside temperature (if sensor fitted)

7 Holiday function

8 Operating mode

9 Line number/day

10 Burner on

11 Heating function

12 Domestic hot water/temperature/D.H.W. load Fig. 9

Fig. 7

“PLANET DEWY 60-100 BFR” BOILER INSTALLATION IN SEQUENCE/CASCADE

WHEN THE BOILER IS CONNECTED TO REGULATOR RVA 47.320 IN SEQUENCE/CASCADE INSTALLA-

TIONS, ALL BOILERS IN THE HEATING UNIT MUST HAVE THEIR “CR/OFF/INV/RELEASE” SELECTORS

POSITIONED AS INDICATED IN FIG. 7.

THE HEATING POTENTIOMETER AND WATER KNOB NO LONGER HAVE ANY CONTROL AND ALL FUNC-

TIONS WILL BE CONTROLLED BY THE TVA 47.320 REGULATOR.

The fixed temperature can be adjusted with the control knob.

Before adjusting it again, however, allow the temperature to stabilise first.

Note: With the temperature knob you can only adjust the fixed temperature, the reduced tem-

perature remains the same.

–Adjusting the temperature

If you turn the knob towards the + sign, the fixed temperature is

increased by about 1 °C for every notch.

If you turn the knob towards the - sign, the fixed temperature is

decreased by about 1 °C for every notch.

Ensure that the radiators in the room with the Logica do not have thermostatic valves, and

are not turned off.

For every operation of the Info key the fol-

lowing list of items, one after the other, are

displayed. The thermo-feeler continues to

function independently of the display.

Day, hour, room temperature

External temperature*

Hot-water service temperature* * Only with outside sensor fitted.

–Info key

(reference key grey colour)

The operating mode desired is selected by

pressing the relative key with the correspon-

ding symbol. The choice is displayed with the

symbol

Automatic functioning: the heating functions automatically according to the hea-

ting programme entered. The programme may be excluded for brief periods with

the on-line key.

Manual functioning: the heating functions manually according to the choice made

with the on-line key.

Availability: the heating is deactivated.

–Selection of the operating mode

(reference keys grey colour)

ACTIVATING

During functioning the lid of the regulator must be closed.

If the rooms remain unused for a long period of time, the temperatu-

re can be reduced with the on-line key, in this way saving energy. When

the rooms are occupied again, press the on-line key to re-heat them.

The current choice is displayed on the display:

–On-line key

Fixed temperature heating

Reduced temperature heating

NOTE:

In automatic mode, the apparatus switches from the fixed temperature to the reduced tem-

perature according to the time programme. The manual switching of the temperature is done

manually with the on-line key.

–Temperature regulation

Fixed temperature:

temperature when the rooms are occupied

(basic setting)

Reduced temperature:

temperature during periods of absence or night

Hot-water service temperature:

– desired temperature of hot-water service

– comfort temperature of the hot-water service

(with hot water cylinder unit)

Reduced temperature of hot-water service (with hot water cylinder unit):

temperature desired for hot-water service at reduced level.

To have access to the “reduced hot-water service temperature” parameter, press

the and keys at the same time for at least 5 seconds and then go along

the entered lines with the key until parameter 61 is reached. Regulate the value

with and

Before proceeding with the adjustment in the temperature on the regulator, the thermostatic

valves, which may be present, have to be regulated to the desired temperature.

PROGRAMMING

To enter the programming mode the flap on the control must be open.

As soon as the cover is open,

the display and the key functions

are switched on.

The number in the square

represents the programme

lines that may selected with the

arrow keys.

You can set or display the following values:

• Temperatures up to

• Heating programme up to

• Day of the week and hour up to

• Current values up to

• Holiday period

• Return to the default values

411

12 14

15 17

If the control is in the manual mode , If the control is in the automatic mode

the control will revert automatically at the next change of the heating programme.

Programme line Value

Value adjustment keys

Programme line selector

–Programme for hot-water service

(with storage capacity boiler unit)

Select the days that correspond with the heating phase.

1= Monday, ... 7 = Sunday/8 = hot-water service programme

Start of phase 1: Start of first comfort period.

End phase 1: End of first comfort period.

Start phase 2: Start of second comfort period.

End phase 2: End of second comfort period.

Start phase 3: Start of third comfort period.

End phase 3: End of third comfort period.

Copying of the daily programme

By pressing this key it is possible to repeat the current heating programme

for the next day.

By pressing this key it is possible to repeat the current heating programme

for the previous day.

As a confirmation the following day is displayed.

With the Logic Remote Control it is possible to manage the temperature of boiler unit on two

levels (a comfort level and one at reduced temperature) in accordance with the programme

chosen with parameter 62 (load hot-water service). To have access to the parameter press

the and keys for at least 5 seconds and then go along the entered lines with the

key until parameter 62 is reached. At this point four different programmes may be selected

with o keys, with the following characteristics:

0= 24 hours/ day - Hot water always available at the temperature set in parameter 3.

1= standard - Hot water according to the daily heating programme. In the comfort periods

of the heating the temperature of the boiler unit is regulated at the value set via para-

meter 61.

2= sservice suspended.

3= second daily programme (8) - Everyday of the week the temperature of the hot-water ser-

vice is set according to programme B. In this case the programming is one for all the days

of the week and three periods of time are available. In the periods of time set, the tem-

perature of the boiler unit is controlled via the temperature setting of parameter 61.

Start phase 1: Start time of first comfort period.

End phase 1: End time of first comfort period

Start phase 2: Start time of second comfort period.

End phase 2: End time of second comfort period.

Start phase 3: Start time of third comfort period.

End phase 3: End time of third comfort period.

–Heating/hot-water

service programme

With the heating programme it is possible to set the switching times of the temperature for a

period of a week. The weekly programme consists of 7 daily programmes. One daily program-

me allows 3 phases of heating. Each phase is defined by a starting time and a finishing time.

The n. 8 daily programme is for the hot-water service (if storage unit connected). If a phase is

not required, the same starting and finishing time may be entered.

192

193

195

Heating sensor fault (SM)