Simons Voss Technologies Cylinder AX Modularity User manual

Cylinder AX
Modularity
Manual
10.11.2021

Contents
1 General safety instructions..................................................................................................................... 3
2 Product-specific safety instructions.................................................................................................... 5
3 Accessories and tools...............................................................................................................................6
4 Extend Cylinder AX....................................................................................................................................8
5 Shorten Cylinder AX ............................................................................................................................... 20
6 Combine CO cylinders to FD.................................................................................................................32
7 Reduce CO cylinders to HZ .................................................................................................................. 48
8 Help and other information .................................................................................................................. 61
Cylinder AX Modularity (Manual) Contents
2 / 62

1 General safety instructions
Signal word (ANSI
Z535.6) Possible immediate effects of non-compliance
DANGER Death or serious injury (likely)
WARNING Death or serious injury (possible, but unlikely)
CAUTION Minor injury
IMPORTANT Property damage or malfunction
NOTE Low or none
WARNING
Blocked access
Access through a door may stay blocked due to incorrectly fitted and/or in-
correctly programmed components. SimonsVoss Technologies GmbH is
not liable for the consequences of blocked access such as access to in-
jured or endangered persons, material damage or other damage!
Blocked access through manipulation of the product
If you change the product on your own, malfunctions can occur and access through a door can
be blocked.
Modify the product only when needed and only in the manner described in the
documentation.
IMPORTANT
Damage resulting from aggressive cleaning agents
The surface of this product may be damaged as a result of the use of un-
suitable cleaning agents.
Only use cleaning agents that are suitable for plastic or metal surfaces.
NOTE
Intended use
SimonsVoss-products are designed exclusively for opening and closing
doors and similar objects.
Do not use SimonsVoss products for any other purposes.
Qualifications required
The installation and commissioning requires specialized knowledge.
Only trained personnel may install and commission the product.
Cylinder AX Modularity (Manual) 1. General safety instructions
3 / 62

Incorrect installation
SimonsVoss Technologies GmbH accepts no liability for damage caused to doors or compon-
ents due to incorrect fitting or installation.
Modifications or further technical developments cannot be excluded and may be implemented
without notice.
The German language version is the original instruction manual. Other languages (drafting in the
contract language) are translations of the original instructions.
Read and follow all installation, installation, and commissioning instructions. Pass these instruc-
tions and any maintenance instructions to the user.
Cylinder AX Modularity (Manual) 1. General safety instructions
4 / 62

2 Product-specific safety instructions
WARNING
Malfunction of the anti-panic function due to unauthorised manipulation
The length of the Cylinder AX can be modified. If the AP side is removed,
the anti-panic unit may be damaged.
Do not change the length on the AP side.
Cylinder AX Modularity (Manual) 2. Product-specific safety instructions
5 / 62

3 Accessories and tools
The profile cylinder can be extended and shortened with the following
parts:
Extension bolt Core extension for the
profile Profile extension
Z5.BOLT.XX (XX =
required basic
length)
Z5.CORE.05: 5mm
Z5.CORE.10: 10 mm
Z5.CORE.20: 20 mm
Z5.PROFILE.05:
5mm
Z5.PROFILE.10: 10
mm
Z5.PROFILE.20: 20
mm
Clamps Half cylinder centre
piece Cylinder centre piece
Z5.CLAMPS
Set contains 50 units. Z5.CNT.HZ Z5.CNT.EU
Cam (standard, WP) Inside thumb-turn mount
Z5.CAM.WP Z5.PR.IN
To do this, you need the following tools:
Cylinder AX Modularity (Manual) 3. Accessories and tools
6 / 62

Extractor (Z5.LIFTER) SPACER (Z5.SPACER) Terminal BLOCK
(Z5.BLOCK)
The Cylinder AX thumb-turn assembly tool is designed so that you can use
it as a bracket for the Cylinder AX. Place it with the flat side on a flat
surface and place the Cylinder AX with the knob in the assembly tool.
Reassembly is easier if the AX cylinder is in the bracket.
Cylinder AX Modularity (Manual) 3. Accessories and tools
7 / 62

4 Extend Cylinder AX
The core extension and profile extension must be the same length. You
also need an extension bolt for the desired length.
üExtractor for releasing the clamp
üSpacer for aligning the extension bolt
üClamp block for pressing in the clamp
1. Place the Cylinder AX in the thumb-turn assembly tool.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
8 / 62

2. Hook the tip of the extractor into the clamp.
3. Lever the clamp out of the profile cylinder by moving the extractor to
the centre of the cylinder.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
9 / 62

4. Pull the clamp completely out of the profile cylinder.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
10 / 62

5. Disassemble the two cylinder halves.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
11 / 62

6. Use the extractor to unscrew the extension bolt.
7. Insert suitable core extensions.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
12 / 62

8. Attach suitable profile extensions.
9. Place the spacer.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
13 / 62

10. Screw in a suitable extension bolt with the extractor until it rests on the
spacer.
NOTE
Length on bolt head
You will find a number on the bolt head. This number is the length of the
cylinder profile to which the bolt fits.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
14 / 62

11. Reassemble the two cylinder halves.
9Extension bolt is protected against twisting.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
15 / 62

12. Pull the spacer off again.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
16 / 62

13. Push the halves together completely.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
17 / 62

14. Place the clip back into the slot of the profile cylinder with its lug facing
the fastening screw and press the clamp with your thumb so that it can
no longer fall out.
15. Insert the cylinder into the clamping block so that the profile cylinder
and the thumb-turn lie flush in the recesses.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
18 / 62

9The lever of the clamping block is reinforced at one point with a
metal plate. The bracket that was previously inserted lies opposite
this metal plate.
16. Push the clamp block lever towards the base plate until the clamp is
fully seated in the profile cylinder.
9Cylinder AX is extended.
Cylinder AX Modularity (Manual) 4. Extend Cylinder AX
19 / 62

5 Shorten Cylinder AX
You need a bolt for the desired length.
üExtractor for releasing the clamp
üSpacer for aligning the bolt
üClamp block for pressing in the clamp
1. Place the Cylinder AX in the thumb-turn assembly tool.
Cylinder AX Modularity (Manual) 5. Shorten Cylinder AX
20 / 62