SJE Rhombus IFS User manual

SILENCE
/TEST
+
DISPLAY
EXP.
1
J5
TB 1 P1
1 2 3 4 5 6
7
8
9
10
T1
T2 RUN T1 T2 RUN
-
P2
L1 L2
P1
L1 L2
P2
AUX
+
24VDC
-
+
-
ALARM
+
-
HORN
STATUS IN IN2 IN3 IN4
E
X
P.
J
5
L1
L2
P2
Installer Friendly Series®
SJE RHOMBUS®Type IFS
Operation Manual
Technical support: [phone]
[email protected]
www.sjerhombus.com
Technical Support Hours: Monday-Friday, 7 A.M. to 6 P.M. Central Time

TABLE OF CONTENTS
Warnings.................................................................................................. 1
Introduction and Specifications...................................................... 2
Main Screen (Programming) ............................................................. 3
User Interface....................................................................................... 3
Main Menu .............................................................................................. 4
HAND/OFF/AUTO Operation .............................................................10
Clearing Counts and ETMs ...............................................................11
Alarms.....................................................................................................12
Troubleshooting Information Screens .........................................13
I/O Tables...............................................................................................17
Mounting Dimensions ........................................................................18
Controller Dimensions .......................................................................18
Schematic Example............................................................................19
SJE Rhombus® Type IFS Operation Manual

WARNINGS
Failure to read and understand the information provided in this manual may result in personal injury
or death, damage to the product or product failure. Please read each section in its entirety and be
sure you understand the information provided in the section and related sections before attempting
any of the procedures or operations given.
Failure to follow these precautions could result in serious injury or death.
Keep these instructions with warranty after installation. This product must
be installed in accordance with National Electrical Code, ANSI/NFPA 70 so
as to prevent moisture from entering or accumulating within the controller
housing.
ELECTRICAL SHOCK HAZARD
A qualified service person must install and service this product
according to applicable codes and electrical schematics.
Disconnect power prior to servicing any equipment.
EXPLOSION OR FIRE HAZARD
Do not use this product with flammable liquids. Do not install
in hazardous locations as defined by National Electrical Code,
ANSI/NFPA 70.
• Do not connect power to this equipment if it has been damaged or has
any missing parts.
• Do not install in areas with: excessive or conductive dust, corrosive or
flammable gas, moisture or rain, excessive heat, regular impact shocks,
or excessive vibration.
SJE Rhombus® 1 Type IFS Operation Manual
Warning: Users must read this manual and understand controller operation before changing any settings. Entering
incorrect settings may result in damage to equipment.
If the controller was shipped pre-installed in a control panel, some default values may have been changed at the
factory in order to properly test the control panel operation. The user must adjust the settings to the requirements
of the installation.
The user should always keep a record of the settings before making changes, in case there is a need to revert to
previous settings. The user should also record all settings changed for use in programming a new controller in case
a replacement is ever needed.
Always thoroughly test controller operation in the installed configuration to verify user settings.

INTRODUCTION & SPECIFICATIONS
Congratulations and thank you for your purchase of a control panel utilizing the Installer Friendly
Series®controller. This manual explains the features and operations of the controller which
was designed to operate up to two pumps for tank pump down applications. The controller
automatically controls the operation of the pump(s) based on the status of float switches or
C-Level™ sensor.
GENERAL
• One or two pump level controller
• Operates using float switches or C-Level™
sensor
• HMI - Rotary selector for menu navigation
and editing settings
• HMI - High-Brightness 2.4” color graphic LCD
display, 240X320 pixel resolution
PUMP CONTROL AND PROTECTION
• Automatic pump alternation (duplex)
• Multiple alternation configurations
• Automatic alternation on pump fault
• Pump run indication
• 1-2 Pump power relays, 240 Vac, 20A max.
SYSTEM
• Alarm counts
• Pump cycle counts
• Pump run time
ELECTRICAL SPECIFICATIONS
• Universal 85-265 Vac, 50/60Hz
Control/Alarm power input
• 0-250 Vac, 50/60Hz, 20A max. Pump Power
input
• 5kA short circuit current rating
• 24 Vdc, class 2 control power
• Auxiliary Power -- 24 Vdc, 100mA max.
DEDICATED I/Os
• 4 Float switch inputs
• C-Level™ sensor with 2 backup floats
• 1 Auxiliary alarm input
• 2 Pump OL/thermal cutout inputs
• 1 Test/Silence/Manual alarm reset input
• 1 Alarm beacon output, 24 Vdc, 60mA max.
• 1 Alarm horn output, 24 Vdc, 30mA max.
COMMUNICATION
• Dedicated display communication port
(RJ45), RS485, Modbus protocol.
• Expansion communication port (RJ45),
RS485, Modbus protocol
ENVIRONMENT
• Operational temperature -20ºF to 122ºF
(-30ºC to 50ºC)
• Storage temperature -40ºF to 140ºF
(-40ºC to 60ºC)
• Relative Humidity (RH) 5% to 95%
(non-condensing)
• Indoor rated - for indoor use or mounted inside
of an outdoor rated enclosure
SJE Rhombus® 2 Type IFS Operation Manual

PROGRAMMING
HMI MAIN SCREEN
The main screen shows an overview of the system status including any active alarms.
Timed Dose Operation
(ON/OFF Timer Status)
USER INTERFACE
SJE Rhombus® 3 Type IFS Operation Manual
Pump HAND/OFF/AUTO
Status/Selection
Pump Hour Meter (selectable)
Settings Menu
Graphical Setpoint Bars (C-Level™)
Level Bar Graph or Float Status
Tank Level (C-Level™)
Color Liquid Crystal Display (LCD)
Menu Navigation
And ENTER Dial
Graphical Timer Count Down
(indicated on lead pump)
Pump Cycle Counts (selectable)
Pump Amps
(selectable - not shown)

MAIN MENU
ROTATE
Counts and ETMs
- Displays pump run time, pump run
counts and alarm counts
Timer Settings (timed dose mode only)
- Congures timers for timed dose
operation
Level Settings
- Congures level setpoints
Alternation (duplex only)
- Congures alternation mode for
duplex panels
Advanced
- Congures advanced functions and
accesses troubleshooting tools
Back
- Exits the Main Menu
SJE Rhombus® 4 Type IFS Operation Manual

SJE Rhombus® 5 Type IFS Operation Manual
Main Menu
Counts and ETM’s
ETM HH:MM:SS
Pump 1 00:00:00
Pump 2 * 00:00:00
Cycles
Pump 1 0000
Pump 2 * 0000
Counts
High Alarm 0
Pump 1 Fault 0
Pump 2 Fault* 0
Pump 1 Overload 0
Pump 2 Overload* 0
Pump 1 Thermal 0
Pump 2 Thermal* 0
Pump 1 Seal 0
Pump 2 Seal
Sensor Fail
* 0
0
Back
*visible only for duplex controllers
Timer Settings (Timed Dose Mode Only)
Pump 1 *
On Time
Off Time
Override On Time
Override Off Time
Pump 2 *
On Time *
Off Time *
Override On Time *
Override Off Time *
Back
*visible only for independent timers mode
Level Settings (C-Level™ Mode Only)
Timed Dose Mode Simplex Demand Dose Mode Duplex Demand Dose Mode
= save and exit X= exit without saving
*the order of the alarm setting changes based on the value entered
Start

SJE Rhombus® 6 Type IFS Operation Manual
Alternation (Duplex Controller Only)
Alternate
Pump 1 Lead
Pump 2 Lead
Back
A
dvanced
Level Sensing
Timed/Demand Dose
Seal Fail/Thermal
Expansion Port
Overload Cutout
Alarm Options
Troubleshooting
Maximum Pumps On
General
Back
Level Sensing
Float Switches
C-Level Sensor
Back
C-Level™
Range (when C-Level™ Sensor is selected)
40” Sensor
Timed/Demand Dose
Timed Dose
Demand Dose
Back
Timer Type (when Timed Dose is selected, duplex panels only)
Single Timer
Independent Timers*
Back
Expansion Port
Seal Fail/Thermal (when Expansion Port is enabled)
Enable
Enable
Disable
Disable
Back
Back
100” Sensor
Back
*Allows for two independent timed dose systems on a duplex panel

SJE Rhombus® 7 Type IFS Operation Manual
Setup Type
Auto
Manual
Manual Setup (when Manual Setup Type is selected)
000.0 kΩ
= save and exit X= exit without saving
Overload Cutout
Enable
Disable
Back
Alarm Options
Beacon Flash
Horn Flash
Manual Reset
Redundant High Water Lag (duplex controller with C-Level™ only)
Seal Fail Alarm (when Seal Fail/Thermal Module enabled)
Thermal Alarm (when Seal Fail/Thermal Module enabled)
Overload Alarm (when Overload Cutout enabled)
Back
Beacon Flash
No Flash
No Flash
Flash All
Flash Alarm 2 Only
Back
Horn Flash
Flash All
Flash Alarm 2 Only
Back
Manual Reset
Redundant High Water Lag
Seal Fail Alarm
Thermal Alarm
Overload Alarm
Enable
Enable
Enable
Disable
Disable
Back
Back
Enable
Enable
Enable
Disable
Back
Back
Disable
Back
Disable
Back

SJE Rhombus® 8 Type IFS Operation Manual
Troubleshooting
C-Level™ Status *
Simulator
Frequency* 1234 Hz
Tank Level* 4.7 in
Float Status **
Lag Down
Alarm Down
Start Down
Stop Down
Pump Status
Pump 1 Called Off
Pump 1 Amps 0.01 A
Pump 2 Called*** Off
Pump 2 Amps*** 0.01 A
Alert Status
Horn Off
Beacon Off
Alarm Aux Off
Input Status
Test/Silence Off
Alarm 2 Off
Overload 1 Off
Overload 2 Off
Fault Status
Pump 1 Inactive
Thermal 1 Inactive
Seal 1 Inactive
Pump 2 *** Inactive
Thermal 2*** Inactive
Seal 2*** Inactive
Controller Status
DC Bus 1 22.50 V
DC Bus 2 11.80 V
DC Bus 3 3.29 V
Back
*Visible only for C
***Visible only for duplex configuration
-Level™ mode
**Float Status for duplex demand dose configuration.
Float labels change based on controller configuration.

SJE Rhombus® 9 Type IFS Operation Manual
General
Firmware
Display V 0.00
Controller V 0.00
Settings
Language
Color Theme
Password Setup
Back
Language
English
Espanol
Francais
Back
Color Theme
Dark
Light
Back
Password Setup
00-00
Enable
= save and exit X
= exit without saving
Float Simulator C-Level™Sensor Simulator
Simulator

SJE Rhombus® 10 Type IFS Operation Manual
HAND/OFF/AUTO OPERATION
PRESS - ENTER
The HAND, OFF, or AUTO operating mode can be
changed for each pump independently.
• An AUTO or OFF setting will always return the
user to the main screen upon selecting.
• A HAND setting will return to the main screen
upon selecting if the tank level is above the
lowest oat or the level sensor’s lowest
setpoint. Once the tank level drops to the
lowest oat or the level sensor’s lowest
setpoint, the controller will automatically be
changed to AUTO mode.
• If the tank level is lower than the lowest
oat or the level sensor’s lowest setpoint,
then the user must press and hold the enter
button to enable HAND mode. Upon releasing
the enter button, in this case, the controller
will automatically be changed to AUTO mode
and will return to the main screen.

SJE Rhombus® 11 Type IFS Operation Manual
CLEARING COUNTS AND ETMS
All counts and elapsed time meters in the “Counts and ETMs” are able to be cleared.
To clear an individual count or ETM:
• Navigate to the “Counts and ETMs” screen and to the data to be cleared.
• Press and hold the enter button.
• Navigate to “Yes” when asked to reset the value.
• Navigate to “Conrm” to clear the count or ETM, or to “Cancel” to exit without clearing the count or
ETM.
Cancel
Conrm
Are You Sure?
Pump 1 ETM

SJE Rhombus® 12 Type IFS Operation Manual
ALARM TEXT DEFINITION FIX
High Level C-Level™Tank level has risen above the high
alarm level setpoint.
• Ensure pumps are operating normally.
• Ensure discharge pipe is intact.
• Ensure the high alarm level setpoint is
set above the normal operating level.
High Level Float Tank level has risen above the high
water oat switch level.
• Ensure pumps are operating normally.
• Ensure discharge pipe is intact.
• Ensure the high water oat switch has
been installed above the normal
operating level.
Redundant O Alarm
Tank level has fallen below the
redundant o oat switch level.
(Redundant o alarm activation
must be enabled - C-Level™sensor
congurations only)
• Ensure pumps are operating normally.
• Ensure there are no leaks in the tank.
• Ensure the redundant o oat switch
has been installed below all other oats
or sensor setpoint levels.
Comm Fault The display has lost communication
connection with the controller.
• Ensure display cable is properly
connected to the display and controller.
Expansion Port Fault
The controller has lost communication
connection with the expansion
modules.
• Ensure expansion module cable is
properly connected to the controller.
P1 Overload
The controller has sensed an open
circuit on the Pump 1 OL/Thermal input
terminals.
• Ensure Pump 1 motor overload relay or
thermal cutout is functioning correctly.
• Ensure Pump 1 motor is functioning
correctly.
P1 Seal Fail
The seal fail module has sensed a seal
leak condition in Pump 1, based on the
seal fail setting.
• Service Pump 1 seal.
P1 Thermal Cutout
The controller has sensed a change
in the status of the Pump 1 thermal
input on the Seal Fail/Thermal Cutout
expansion module.
• Ensure Pump 1 motor thermal cutout is
functioning correctly.
• Ensure Pump 1 motor is functioning
correctly.
P1 Fault
The controller has operated in lag mode
for three consecutive cycles while
Pump 1 was lead pump.
• Ensure Pump 1 is operating normally.
• Ensure the discharge pipe for Pump 1 is
intact.
P2 Overload
The controller has sensed an open
circuit on the Pump 2 OL/Thermal input
terminals.
• Ensure Pump 2 motor overload relay or
thermal cutout is functioning correctly.
• Ensure Pump 2 motor is functioning
correctly.
P2 Seal Fail
The seal fail module has sensed a seal
leak condition in Pump 2, based on the
seal fail setting.
• Service Pump 2 seal.
P2 Thermal Cutout
The controller has sensed a change
in the status of the Pump 2 thermal
input on the Seal Fail/Thermal Cutout
expansion module.
• Ensure Pump 2 motor thermal cutout is
functioning correctly.
• Ensure Pump 2 motor is functioning
correctly.
P2 Fault
The controller has operated in lag mode
for three consecutive cycles while
Pump 2 was lead pump.
• Ensure Pump 2 is operating normally.
• Ensure the discharge pipe for Pump 2 is
intact.
Float Fail
The controller has sensed a oat
switch closure that is outside of the
normal sequence of operation.
• Ensure the oat switches have been
installed in the proper order.
• Ensure the oat switches do not
contact the sides of the tank, or
objects in the tank.
ALARMS

SJE Rhombus® 13 Type IFS Operation Manual
ALARMS - Continued
ALARM TEXT DEFINITION FIX
Stop Float Fail
The controller has sensed that the
stop oat has failed to close while
higher level oat switches have closed
• Ensure the oat switches have been
installed in the proper order.
• Ensure the oat switches do not
contact the sides of the tank, or
objects in the tank.
Lead Float Fail
The controller has sensed that the lead
oat has failed to close while the stop
and higher level oat switches have
closed.
• Ensure the oat switches have been
installed in the proper order.
• Ensure the oat switches do not
contact the sides of the tank, or
objects in the tank.
O Float Fail
The controller has sensed that the
redundant o oat has failed to close
while higher level oat switches have
closed.
• Ensure the oat switches have been
installed in the proper order.
• Ensure the oat switches do not
contact the sides of the tank, or
objects in the tank.
Enable Float Fail
The controller has sensed that the
timer enable oat has failed to close
while the redundant o and higher level
oat switches have closed.
• Ensure the oat switches have been
installed in the proper order.
• Ensure the oat switches do not
contact the sides of the tank, or
objects in the tank.
Float Cong Error
The controller has sensed a C-Level™
sensor signal connected to the eld
wiring terminals, while congured as
oat switch controlled.
• Ensure the controller is congured for
C-Level™sensor.
C-Level™Error
The controller has sensed a signal
outside the normal operating range of
the C-Level™sensor.
• Ensure the controller is congured for
oat switch control if a C-Level™
sensor is not used.
• Ensure the C-Level™sensor is properly
connected to the controller.
• Ensure the C-Level™sensor cable has
not been damaged.
Alarm 2 A contact closure has been sensed by
the Alarm 2 input circuit.
• Check the system monitored by the
Alarm 2 input.
Alarm 3
A contact closure has been sensed by
the fourth digital input circuit when
in Simplex Demand mode or Duplex
Demand 3-Float mode.
• Check the system monitored by the
fourth digital input.
Press Test/Silence to Reset Alarm
The controller is congured for manual
alarm reset and the formerly active
alarm is now inactive.
• Press the Test/Silence button to reset
the alarm status.

SJE Rhombus® 14 Type IFS Operation Manual
TROUBLESHOOTING INFORMATION SCREENS
Current Panel Conguration
Duplex
Timed Dose
C-Level™Sensor
40” Sensor
This section displays the current conguration of the controller. *The example shows a controller
congured as a Duplex, Timed Dose using a 40” C-Level™sensor for level sensing.
C-Level™Status
Simulator
Frequency 2315 Hz
Tank Level 26.3 in
The simulator is used to verify the functionality of the controller by simulating the tank level.
This section displays the frequency of the C-Level™sensor as measured by the controller, as well
as the calculated tank level. The normal operating range of the C-Level™sensor is between 1000Hz
and 3000Hz. If the C-Level™sensor frequency is operating signicantly outside of the normal range,
a “Sensor Fail” alarm will occur.
Float Status
Redundant High Level Down
Redundant Low Level Up
This screen displays the status of each oat switch connected to the controller. *The example shows a
controller congured as C-Level™ sensor control.
Pump Status
Pump 1 Called O
Pump 1 Amps 0.0 A
Pump 2 Called O
Pump 2 Amps 0.0 A
This screen displays the status of each pump connected to the controller. *The example shows a
controller congured as Duplex.
Alert Status
Horn O
Beacon O
Alarm Aux O
This screen displays the status of the controller alarm.

SJE Rhombus® 15 Type IFS Operation Manual
TROUBLESHOOTING INFORMATION SCREENS - Continued
Input Status
Test/Silence O
Alarm 2 O
Overload 1 O
Overload 2 O
This section displays the status of the general inputs on the controller.
Fault Status
Pump 1 Inactive
Thermal 1 Inactive
Seal 1 Inactive
Pump 2 Inactive
Thermal 2 Inactive
Seal 2 Inactive
This section displays the fault status of each pump connected to the controller. *The example shows
a controller congured as Duplex with a thermal/seal fail module.
Controller Status
DC Bus 1 22.41 V
DC Bus 2 11.79 V
DC Bus 3 3.29 V
This section displays the status of the voltage buses on the controller.

SJE Rhombus® 16 Type IFS Operation Manual
I/O TABLES
TB1 - SUPPLY POWER, LEVEL SENSING, PUMP
AND AUXILIARY ALARM CONTACTS
TERMINAL DESCRIPTION
190-265 VAC SUPPLY
2 90-265 VAC SUPPLY
3 DIGITAL INPUT COMMON
4 DIGITAL INPUT 1
5 DIGITAL INPUT COMMON/C-LEVEL
NO-CONNECTION
6DIGITAL INPUT 2/C-LEVEL (+) SUPPLY
7 DIGITAL INPUT COMMON/C-LEVEL (-) SUPPLY
8 DIGITAL INPUT 3/C-LEVEL SIGNAL INPUT
9 DIGITAL INPUT COMMON
10 DIGITAL INPUT 4
P1:T1 PUMP 1 (T1)
P1:T2 PUMP 1 (T2)
P2:T1 PUMP 2 (T1)
P2:T2 PUMP 2 (T2)
AUX:1 AUXILIARY ALARM CONTACT (N.O.)
AUX:2 AUXILIARY ALARM CONTACT (N.O.)
TB3- PUMP SUPPLY POWER
TERMINAL DESCRIPTION
P1:L1 PUMP 1 (L1)
P1:L2 PUMP 1 (L2/N)
P2:L1 PUMP 2 (L1)
P2:L2 PUMP 2 (L2/N)
TB2- HORN, BEACON, TEST/SILENCE SWITCH,
AUX 24VDC SUPPLY
TERMINAL DESCRIPTION
1TEST/SILENCE/RESET SWITCH (1)
2 TEST/SILENCE/RESET SWITCH (2)
3 ALARM LIGHT (0V)
4 ALARM LIGHT (24V)
5 ALARM HORN (0V)
6 ALARM HORN (24V)
7 AUX 24VDC SUPPLY (-)
8 AUX 24VDC SUPPLY (+)
All Digital Input functions are activated upon a
contact closure to the Digital Input Common
terminal.
Note:
Terminals TB1-3, TB1-5, TB1-7, TB1-9 commons
are internally connected.
J5 - ALARM 2, OVERLOAD 1, OVERLOAD 2
TERMINAL DESCRIPTION
1ALARM 2 INPUT
2 OVERLOAD 1 INPUT
3 OVERLOAD 2 INPUT
4 DIGITAL INPUT COMMON
5 DIGITAL INPUT COMMON
6 DIGITAL INPUT COMMON
*J5
6 4
3 1

SJE Rhombus® 17 Type IFS Operation Manual
MOUNTING DIMENSIONS (DISPLAY)
CONTROLLER DIMENSIONS

SJE Rhombus® 18 Type IFS Operation Manual
SCHEMATIC EXAMPLE