SKF MAX-1-2-230-IF105-R-V2 Manual

CHANGE OVER VALVE UNIT
SKF MAXILUBE
(Translation from original Finnish operating and maintenance instructions compliant
with EU Directive 2006/42/EC)

TABLE OF CONTENTS
1 EC Declaration of incorporation, SKF Maxilube with internal control (power supply 230V/115V) .........4
2 EU Declaration of incorporation, SKF Maxilube with external control (control voltage 24V) ...............5
3 Legal disclosure ..............................................................................................................................................6
4 Explanation of symbols, signs and abbreviations......................................................................................7
5 Safety instructions ........................................................................................................................................10
5.1 General safety instructions...........................................................................................................................10
5.2 General behaviour when handling the product.............................................................................................10
5.3 Intended use.................................................................................................................................................10
5.4 Foreseeable misuse .....................................................................................................................................11
5.5 Modifications to the product..........................................................................................................................11
5.6 Other applicable documents.........................................................................................................................11
5.7 Notes concerning the type identification plate..............................................................................................11
5.8 Persons authorised to operate the device....................................................................................................12
5.8.1 Operator.................................................................................................................................................12
5.8.2 Mechanical specialist.............................................................................................................................12
5.8.3 Electrician...............................................................................................................................................12
5.8.4 Providing briefing for external technicians.............................................................................................12
5.8.5 Provision of personal protective equipment...........................................................................................12
5.9 Operation......................................................................................................................................................12
5.9.1 Stopping the pump in an emergency.....................................................................................................12
5.9.2 Transport, installation, maintenance, malfunctions and repairs ............................................................12
5.10 Commissioning and daily start-up ..............................................................................................................13
5.11 Cleaning......................................................................................................................................................13
6 Lubricants ......................................................................................................................................................15
6.1 General information......................................................................................................................................15
6.2 Lubricant selection........................................................................................................................................15
6.3 Material compatibility....................................................................................................................................16
6.4 Ageing of lubricants ......................................................................................................................................16
7 General description.......................................................................................................................................17
7.1 Maxilube pumping centre .............................................................................................................................17
7.2 SKF Maxilube changeover valve unit...........................................................................................................18
8 Operation........................................................................................................................................................19
8.1 Operation of the pumping centre..................................................................................................................19
8.2 Commissioning .............................................................................................................................................19
8.2.1 Maxilube with ECO lid set......................................................................................................................20
8.2.2 Maxilube with STA lid set.......................................................................................................................21
8.3 Replacing the lubricant barrel.......................................................................................................................22
8.3.1 Maxilube ECO........................................................................................................................................22
8.3.2 Maxilube STA.........................................................................................................................................23
8.4 Manual operation..........................................................................................................................................24
9 IF-105 user interface......................................................................................................................................25
9.1 General information......................................................................................................................................25
9.2 Design...........................................................................................................................................................25
9.3 LED-signals for channels..............................................................................................................................26
9.4 LED-signals for operation.............................................................................................................................26
9.5 Buttons..........................................................................................................................................................27

9.6 Display..........................................................................................................................................................27
10 IF-105 operation...........................................................................................................................................28
10.1 Normal mode..............................................................................................................................................28
10.1.1 Functions..............................................................................................................................................28
10.1.2 Phase codes for normal mode and alarm mode..................................................................................29
10.1.3 Normal mode displays, MonoFlex and and DuoFlex lubrication systems...........................................30
10.1.4 Normal mode displays, Progressive lubrication system ......................................................................31
10.1.5 Pressure and pulse displays for lines ..................................................................................................32
10.2 Power failure...............................................................................................................................................32
10.3 Alarms.........................................................................................................................................................32
10.3.1 Low level alarm....................................................................................................................................32
10.3.2 Pressure alarm, MonoFlex and DuoFlex lubrication systems..............................................................32
10.3.3 Pulse alarm, ProFlex lubrication system..............................................................................................33
10.3.4 Alarm from SKF Doser monitor -doser operation indicator..................................................................33
10.3.5 Alarm from the air pressure switch of the grease spray system..........................................................34
10.3.6 Warning message for pump change (doubled pumping center/Dualset) ............................................34
10.4 Manual operation........................................................................................................................................34
11 IF-105 settings..............................................................................................................................................35
11.1 General.......................................................................................................................................................35
11.2 Entering password......................................................................................................................................35
11.3 Entering settings.........................................................................................................................................35
11.3.1 Lubrication cycle counter .....................................................................................................................35
11.3.2 Lubrication cycle ..................................................................................................................................35
12 IF-105 technical specification.....................................................................................................................36
12.1 Technical data ............................................................................................................................................36
12.2 Symbols......................................................................................................................................................36
13 Maxilube troubleshooting...........................................................................................................................37
14 Maxilube technical specification................................................................................................................40
14.1 Technical specifications Maxilube changeover valve unit..........................................................................40
14.2 Connections................................................................................................................................................41
14.2.1 SKF Maxilube changeover valve unit...................................................................................................41
14.3 Designations – Maxilube changeover valve unit ........................................................................................42
15 Periodic inspections....................................................................................................................................44
16 Troubleshooting ..........................................................................................................................................44
16.1 Malfunctions................................................................................................................................................44
16.2 Troubleshooting table.................................................................................................................................45
17 Shutdown, decommissioning and storage...............................................................................................46
17.1 Temporary shutdown..................................................................................................................................46
17.2 Final decommissioning...............................................................................................................................46
17.3 Storage .......................................................................................................................................................46
18 Spare parts...................................................................................................................................................47

MAXILUBE_2A_EN.docxC 2019
4
1 EC Declaration of incorporation, SKF
Maxilube with internal control (power sup-
ply 230V/115V)
Original Declaration of Incorporation for Partly Completed Machinery
(Machinery Directive 2006/42/EC, Annex II, part 1, section B)
Oy SKF Ab
Teollisuustie 6 (P.O. Box 80)
FIN-40951 MUURAME
Person authorised to compile the relevant technical documentation:
Technical Manager and Product Manager, Centralised Lubrication Systems, Muurame Unit.
Herewith declares that for the partly completed machinery:
SKF Maxilube MAX-X-X-230-IF105-X-X-X
SKF Maxilube MAX-X-X-115-IF105-X-X-X
•the following essential requirements of the Machinery Directive 2006/42/EC are applied and fulfilled:
1.1.2. 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.2, 1.2.3, 1.2.4, 1.2.6, 1.3.1, 1.3.2, 1.3.4, 1.3.7, 1.5.1, 1.5.4, 1.5.6,
1.5.7, 1.5.13, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1, 1.7.2, 1.7.3, 1.7.4
•the relevant technical documentation is compiled in accordance with part B of Annex VII and that this
documentation or parts hereof will be transmitted by post or electronically in response to a reasoned re-
quest by the national authorities
•and that this partly completed machinery is in conformity with the provisions of the following other EC Di-
rectives:
−EMC Directive 2014/30/EC
−Low Voltage Directive 2014/35/EC
•and furthermore declares that the following European harmonised standards have been used:
−Machinery Directive 2006/42/EC EN ISO 12100-1/A1, EN ISO 12100-2/A1
−EMC Directive 2014/30/EC EN 61000-6-4:2011 (interference emissions); EN 61000-6-2:2006 (inter-
ference immunity)
−Low Voltage Directive 2014/35/EC IEC 61010-1:2010
This partly completed machinery must not be put into service until the final machinery into which it is to be in-
corporated has been declared in conformity with the provisions of the Machinery Directive 2006/42/EC, where
appropriate.
In Muurame 5 April 2016
Place Time
Juha Kärkkäinen
Manager R&D Nordic
SKF Lubrication Business Unit

5
2 EU Declaration of incorporation,
SKF Maxilube with external control
(control voltage 24V)
Original declaration of incorporation for partly completed machinery
(Machinery Directive 2006/42/EC, Annex II, part 1, section B)
Oy SKF Ab
Teollisuustie 6 (P.O. Box 80)
FI-40951 MUURAME, FINLAND
Person authorised to compile the relevant technical documentation:
Technical Manager and Product Manager, Centralized Lubrication Systems, Muurame Unit.
Herewith declares that for the partly completed machinery:
SKF Maxilube MAX-X-X-24-X-X-X
•the following essential requirements of the Machinery Directive 2006/42/EC are applied and fulfilled:
1.1.2. 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.2.2, 1.2.3, 1.2.4, 1.2.6, 1.3.1, 1.3.2, 1.3.4, 1.3.7, 1.5.1, 1.5.4, 1.5.6,
1.5.7, 1.5.13, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1, 1.7.2, 1.7.3, 1.7.4
•The relevant technical documentation is compiled in accordance with part B of Annex VII of the Machin-
ery Directive and that this documentation or parts hereof will be transmitted by post or electronically in
response to a reasoned request by the national authorities.
•And furthermore, declares that this partly completed machinery complies with the following European
harmonised standards:
−Machinery directive 2006/42/EC: EN ISO 12100-1/A1, EN ISO 12100-2/A1
This partly completed machinery must not be put into service until, where appropriate, the final machinery into
which it is to be incorporated has been declared in conformity with the provisions of the Machinery Directive
2006/42/EC.
Muurame April 05, 2016
Place Date
Juha Kärkkäinen
Manager R&D Nordic
SKF Lubrication Business unit

6
3 Legal disclosure
Manufacturer
Oy SKF Ab Finland, Lubrication Product Division
Teollisuustie 6
FI-40951 MUURAME
Finland
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
www.skf.com/fi/lubrication
Training courses
In order to provide a maximum of safety and economic viability, SKF provides detailed training courses. At-
tending the training courses is recommended. For further information, please contact the provided SKF Ser-
vice address.
Copyright
© SKF. All rights reserved.
Warranty and liability
Oy SKF Ab assumes no liability, nor will the warranty provided cover any loss in the following cases:
•The system or component has been used for something other than its intended purpose.
•The system or component has not been installed, commissioned, decommissioned, maintained or used
according to the instructions provided.
•Impure lubricants or materials not approved by Oy SKF Ab have been used in the system or component.
•The system or component has been incorrectly maintained or repaired.
•Parts other than Oy SKF Ab's original spare parts have been used in the system or component.
•The system or component has been altered in ways that Oy SKF Ab has not approved.
•The system or component has been used outside the specified operating limits.
•The system or component has not been stored according to the storage instructions herein.
Notes related to the operating instructions
The present operating instructions are original operating instructions of the manufacturer pursuant to Machin-
ery Directive 2006/42/EC. The instructions are part of the described products and must be kept in an accessi-
ble location for further use.
Disclaimer
The manufacturer shall not accept any liability for damages caused by the following actions by the customer:
•accidents, negligent or inappropriate use, assembly, operation, configuration, maintenance or repairs,
•improper or late response to malfunctions,
•unauthorised modifications to the product,
•intent or negligence, and
•the use of non-original (non-SKF) spare parts.
Liability for loss or damage resulting from the use of our products is limited to the maximum purchase price.
Liability for consequential damages of any kind is excluded.

7
4 Explanation of symbols, signs and
abbreviations
The following symbols are used in the safety instructions included in this manual to highlight conditions which
are potentially harmful to people, materials or the environment.
Please follow the instructions provided especially in the highlighted conditions. Also, relate the safety instruc-
tions to other operators.
General warning Risk of electric shock
Risk of slipping Hot surface
Fire hazard
Use protective goggles
Use hearing protectors Read the operating instructions before use
General note Environmentally friendly disposal
Dispose of cartridges in an
environmentally friendly
way
Warning level Consequence Probability
DANGER Death, serious injury imminent
WARNING Death, serious injury possible
CAUTION Minor injury possible
ATTENTION Property damage possible

8
ap-
prox.
approximately °C degrees Celsius °F degrees Fahrenheit
i.e.
that is
K
Kelvin
Oz.
Ounce
etc.
et cetera
N
Newton
fl. oz.
fluid ounce
poss.
possibly
h
hour
in.
inch
incl.
including
s
second
psi
pounds per square inch
min.
minimum
d
day
sq.in.
square inch
max.
maximum
Nm
Newton metre
cu. in.
cubic inch
min
minute
ml
millilitre
mph
miles per hour
etc.
et cetera
ml/d
millilitre per day
rpm
revolutions per minute
e.g.
for example
cc
cubic centimetre
gal.
gallon
kW
kilowatt
mm
millimetre
lb.
pound
U
voltage
l
litre
hp
horse power
R
resistance
dB (A)
sound pressure level
kp
kilopond
I
current
>
greater than
fpsec
feet per second
V
volt
<
less than
W
watt
±
plus/minus
AC
alternating current
Ø
diameter
DC
direct current
kg
kilogram
A
ampere
rh
relative humidity
Ah
Ampere hour
≈
approximately
Hz
frequency [Hertz]
=
equal to
NC
normally closed
%
per cent
NO
normally open
‰
per mille
≥
equal to or greater than
≤
equal to or less than
mm2
square millimetre
Symbol Meaning
 Instruction step
 List item
 Conditions which must be met
before the activities described in the title clause
can be completed
 Related factors, causes or consequences

9
Conversion factors
length 1 mm = 0.03937 in.
area 1 cm² = 0.155 sq.in
volume 1 ml = 0.0352 fl.oz.
1 l = 2.11416 pints (US)
mass 1 kg = 2.205 lbs
1 g = 0.03527 oz.
density 1 kg/cc = 8.3454 lb./gal (US)
1 kg/cc = 0.03613 lb./cu.in.
force 1 N = 0.10197 kp
pressure 1 bar = 14.5 psi
temperature °C = (°F–32) x 5/9
output 1 kW = 1.34109 hp
acceleration 1 m/s² = 3.28084 ft./s²
speed 1 m/s = 3.28084 fpsec.
1 m/s = 2.23694 mph

10
5 Safety instructions
5.1 General safety instructions
•These safety instructions should be read and followed by any persons entrusted with working on the
product and those who supervise or instruct the group of persons mentioned above. In addition, the
owner must ensure that the relevant personnel are fully familiar with the contents of the instructions
and have understood them. It is prohibited to commission or operate the product prior to reading the
instructions.
•These instructions must be kept for further use.
•The described products have been manufactured according to the state of the art. However, if the
products are used for other than their intended purpose, there may be risks which may result in per-
sonal injury or property damage.
•Any malfunctions which may affect safety must be remedied immediately. In addition to these instruc-
tions, general statutory regulations for accident prevention and environmental protection must be ob-
served.
5.2 General behaviour when handling the product
•Please follow these instructions whenever you use the product. If the product is not in proper technical
condition or you are unaware of the potential hazards, do not use the product.
•Familiarise yourself with the functions and operation of the product. All specified assembly and oper-
ating steps must be competed in the indicated order.
•Any unclear points regarding proper condition or correct assembly/operation must be clarified. Opera-
tion is prohibited until issues have been clarified.
•Prevent unauthorised access.
•Always wear personal protective equipment.
•Take the proper precautions and follow the instructions concerning the relevant task. Responsibilities
for different activities must be clearly defined and observed. Uncertainty is a major risk factor for
safety.
•Safeguards and other protective and emergency equipment must not be removed, modified, discon-
nected or otherwise disabled. Their completeness and function must also be checked at regular inter-
vals.
•If a safeguard or other protective equipment has to be detached, it must be reattached and tested im-
mediately after the work is complete.
•Remedy any faults included in your area of responsibility. If the fault is beyond your competence, no-
tify your supervisor immediately of the fault.
•Never use parts of the centralised lubrication system or of the machine as standing or climbing aids.
5.3 Intended use
Supply of lubricants within a centralised lubrication system in accordance with the specifications, technical
data and limits stated in these instructions: Usage is allowed exclusively for professional users in the frame of
commercial and economic activities.

11
5.4 Foreseeable misuse
Any use differing from that stated in these instructions is strictly prohibited, particularly the following:
•use outside the indicated temperature range,
•use of non-specified lubricants,
•exceeding the maximum allowable operating pressure,
•use in continuous operation,
•use in areas with aggressive or corrosive materials (e.g. high ozone pollution),
•use in areas with harmful radiation (e. g. ionising radiation),
•feeding, forwarding, or storing hazardous substances and mixtures described in Annex I part 2–5 of
the CLP regulation (EG 1272/2008) and marked with warnings GHS01–GHS06 and GHS08
•feeding, forwarding or storing gases, liquefied gases, dissolved gases, vapours or fluids whose va-
pour pressure exceeds normal atmospheric pressure (1,013 mbar) by more than 0.5 bar at the maxi-
mum permissible operating temperature, and
•use in an explosion protection zone.
5.5 Modifications to the product
Unauthorised conversions or modifications may have unforeseeable effects on product safety and functional-
ity. Therefore, any unauthorised conversions or modifications are expressly prohibited.
5.6 Other applicable documents
In addition to these instructions, the following documents must be observed by the respective target group:
•operational instructions and approval rules
•safety data sheet (MSDS) of the lubricant used
Where appropriate:
•project planning documents
•instructions provided by the suppliers of purchased parts
•any documents of other components required to set up the centralised lubrication system
•other documents relevant for the integration of the product into the machine or system.
5.7 Notes concerning the type identification plate
The type identification plate indicates the type desig-
nation, order code and other key details of the ma-
chine.
To make sure no information is lost if the type identi-
fication plate becomes illegible, enter the details in
this manual:
Type _______________________________
Code ________________________________
Date of manufacture ________________________

12
5.8 Persons authorised to operate the device
5.8.1 Operator
An operator is a person who is qualified to carry out the functions and activities related to normal operation
based on his or her training, knowledge and experience. This includes avoiding possible hazards that may
arise during operation.
5.8.2 Mechanical specialist
A mechanical specialist is a person with appropriate professional education, knowledge and experience to de-
tect and avoid the hazards that may arise during transport, installation, commissioning, operation, mainte-
nance, repair and disassembly.
5.8.3 Electrician
An electrician is a person with appropriate professional education, knowledge and experience to detect and
avoid electrical hazards.
5.8.4 Providing briefing for external technicians
Prior to commencing any activities, external technicians must be informed by the end-user of its safety provi-
sions, applicable accident prevention procedures and the functions of the superordinate machine and its pro-
tective devices.
5.8.5 Provision of personal protective equipment
The end-user must provide suitable personal protective equipment for the respective location of operation and
the purpose of operation.
5.9 Operation
The following must be observed during commissioning and operation:
•any information within this manual and the information within the referenced documents, and
•all laws and regulations that the end-user must observe.
5.9.1 Stopping the pump in an emergency
Conduct an emergency stop as follows:
•Cut off the pump’s pressurised air supply from the pressure air regulator.
5.9.2 Transport, installation, maintenance, malfunctions and repairs
•All relevant persons must be informed of the activity prior to starting any work. Observe the precau-
tionary operational measures and work instructions.
•Transport the products with suitable transportation and hoisting equipment using suitable work meth-
ods.
•Maintenance and repair work can be subject to restrictions in low or high temperatures (e.g. changed
flow properties of the lubricant). Therefore, where possible, try to carry out maintenance and repair
work at room temperature.
•Before conducting any work, depressurise the product or machine into which the product will be inte-
grated and secure it against unauthorised activation.
•Ensure through suitable measures that movable or detached parts are immobilised during the work

13
and that no limbs can be caught in between if there are inadvertent movements.
•Assemble the product only outside of the operating range of moving parts, at an adequate distance
from sources of heat or cold. Be careful not to damage other units in the machine or vehicle or impair
their function during installation.
•Dry or cover wet, slippery surfaces accordingly.
•Cover hot or cold surfaces accordingly.
•Work on electrical components must be carried out by electrical specialists only. Observe any waiting
periods for discharging, if necessary. Carry out work on electrical components using voltage insulated
tools only.
•Make electrical connections only according to the information in the valid wiring diagram and taking
the relevant regulations and the local connection conditions into account.
•Do not touch cables or electrical components with wet or damp hands.
•Do not bypass any fuses. Replace fuses with same type and rating only.
•Do not drill holes to critical, load-bearing parts. Use existing boreholes whenever possible. Be careful
not to damage lines and cables when drilling.
•Observe possible abrasion points. Protect the parts accordingly.
•All components used must be suitable for use in:
– the system’s maximum operating pressure, and
– the system’s minimum and maximum ambient temperature range.
•No parts of the centralised lubrication system may be subjected to torsion, shear or bending.
•Before using any parts, check them for contamination, clean if necessary.
•Before installation, prime the hoses between the doser group and the lubrication point with lubricant.
This makes it easier to bleed the system of air afterwards.
•Observe the specified tightening torques. Use a calibrated torque wrench.
•When working with heavy parts, use suitable lifting tools.
•Avoid mixing up or wrong assembly of dismantled parts. Mark these parts accordingly.
5.10 Commissioning and daily start-up
Ensure that:
•All safety devices are complete and work properly.
•All connections are correctly connected.
•All parts have been correctly installed.
•All warning labels on the machine are complete, highly visible and undamaged.
•Replace illegible or missing warning labels without delay.
5.11 Cleaning
•There is a risk of fire and explosion when using flammable cleaning agents. Use only non-flammable
cleaning agents suitable for the purpose.
•Do not use aggressive cleaning agents.
•Do not use steam jet or high pressure cleaners. Electrical components may be damaged. Observe the
IP protection class.
•Cleaning work on energised components may be carried out by electrical specialists only.
•Mark damp areas accordingly.

14
Residual risk
Possible in lifecycle stage
Prevention/remedy
Personal injury / material damage
due to falling of raised parts
A, B, C, G, H, K
Keep unauthorised people away.
Make sure no one remains under
suspended parts or loads. Lift
parts with suitable and tested lift-
ing devices.
Personal injury / material damage
due to tilting or falling of the prod-
uct because of non-observance
of the stated tightening torques
B, C, D, G
Observe the specified tightening
torques. Fasten the product to
components with adequate load-
bearing capacities only. If no
tightening torques are stated,
tightening torques for grade 8.8
screws apply.
Personal injury / material damage
due to electric shock from a dam-
aged connection cable
B, C, D, E, F, G, H
Check that the low level switch
connection cable is intact before
using the switch for the first time
and, after that, at regular inter-
vals. Do not mount the cable to
moving parts or at an abrasion
point. If this cannot be avoided,
use either spring coils or protec-
tive conduits depending on the
circumstances.
Personal injury / damage to mate-
rial due to spilled or leaked lubri-
cant
B, C, D, F, G, H, K
When replacing the barrel, detach
and reattach lubricant feed lines
with care. Always use appropriate
hydraulic screw connections and
lubrication lines suitable for use in
the stated pressures. Do not
mount lubrication lines to moving
parts or abrasion points. If this
cannot be avoided, use either
flexible hose lines, spring coils or
protective conduits depending on
the circumstances.
Lifecycle stages: A = transport, B = installation, C = commissioning, D = operation, E = cleaning, F =
maintenance,
G = fault, repair, H = decommissioning, K = disposal

15
6 Lubricants
6.1 General information
Different lubricants are used in different applications. In order to fulfil their tasks, lubricants must fulfil various
requirements to varying extents. The most important requirements for lubricants are:
•reduction of abrasion and wear
•corrosion protection
•noise minimisation
•protection against contamination and entry of foreign objects
•cooling (primarily for oils)
•longevity (physical/chemical stability)
•compatibility with as wide range of materials as possible
•economic and ecological aspects
6.2 Lubricant selection
SKF considers lubricants to be an element of system design. A suitable lubricant is selected already when de-
signing the machine and it forms the basis for centralised lubrication system planning.
The selection is made by the manufacturer/end-user of the machine, preferably together with the lubricant
supplier based on a defined requirement profile.
Should you have little or no experience with the selection of lubricants for centralised lubrication systems,
please contact SKF.
If required, we will be glad to support customers in selecting suitable components for feeding the selected lub-
ricant and planning and designing their centralised lubrication system.
You will avoid possible costly downtimes caused by damage to your machine/system or the centralised lubri-
cation system.
Only lubricants specified for the product may be used. Unsuitable lubri-
cants may lead to product failure.
Do not mix lubricants. This may have unforeseeable effects on the usa-
bility and therefore on the function of the centralised lubrication system.
Due to the multitude of possible additives, it is possible that individual
lubricants, which according to the manufacturer's data sheets match the
system’s specification, might not in fact suitable for use in centralised lu-
brication systems (e.g. incompatibility between synthetic lubricants and
materials). To avoid this problem, always use lubricants tested by SKF.

16
6.3 Material compatibility
Lubricants must generally be compatible with the following materials:
•steel, grey iron, brass,
•copper, aluminium
•NBR, FPM, ABS, PA, PU
6.4 Ageing of lubricants
After a prolonged downtime of the machine, the lubricant may no longer be suitable for use due to chemical or
physical ageing and must therefore be inspected before the system is recommissioned. We recommend in-
specting the lubricant already after a week’s downtime.
If you suspect that the lubricant is no longer suitable, replace it prior to recommissioning and, if necessary,
perform initial lubrication manually.
It is possible for lubricants to be tested in the company's laboratory for their suitability for being pumped in
centralised lubrication systems (e.g. no "bleeding").
Please contact SKF if you have further questions regarding lubricants.
An overview of the lubricants tested by SKF is also available upon request.

17
7 General description
7.1 Maxilube pumping centre
The pumping centre of the SKF MaxiLube central lubrication system is designed for pumping lubricant into a
centralised lubrication system. The pumping centre can be controlled and monitored using the control unit in-
tegrated in the changeover valve unit, using external control or by sending SMS messages.
The Maxilube pumping centre consists of a pump (I), a lid set (II), a pressure air regulator (III) and a change
over valve unit (IV) with accessories.
Item Description
I
Pump
II
Lid set (ECO or STA)
III
Pressure air regulator
IV
Changeover valve unit
Figure 1: Construction of SKF Maxilube pumping centre

18
7.2 SKF Maxilube changeover valve unit
The changeover valve unit includes a solenoid valve group (4) and a control valve group (2), pressure gauges
(7) and a fixing plate which contains a bracket for the pump during the changing of the barrel. The Maxilube
pumping centre includes a user interface (5) and a circuit board (3).
Item Description
1
Control valve
2
CHV-100 control cartridge (1 or 2 pcs)
3
Circuit board ST105A
4
Solenoid valve 24 V
5
User interface IF-105
6
Power supply 115/230VAC
7
Pressure gauge
Figure 2: Construction & PI diagram of Maxilube
P
R
MV3
MV2 MV1

19
8 Operation
8.1 Operation of the pumping centre
When pressurisation starts, control unit opens both the line to be pressurised and the pump solenoid valves.
Pneumatic system starts the pump and opens the line control valve. Pressurisation continues until the pres-
sure at the pressure monitoring unit reaches a pre-set acknowledgement level. After acknowledgement, the
control unit closes the solenoid valves, the pump stops and pressure discharges from the line to the lubricant
barrel.
If the lubricant level in the barrel reaches the low limit level during pumping, the low-level switch sends an
alarm to the control unit and pumping is stopped. The alarm can be reset by replacing the lubricant barrel and
resetting the alarm at the control unit.
The numbers in brackets are the position numbers for Figure 2.
8.2 Commissioning
DANGER
Electrical shock
Electrical connections must only be made by qualified electricians. Minimise the risk of electric shock by
making sure that the pumping centre is turned off before making connections. Power must be turned off
before work involving handling of conductive parts or opening any part of the system or product.
WARNING
Pressurised lubricant
Make sure that the system is depressurised. Remove pressure from the grease filter before opening it with
the help of a venting screw located in the filter plug (11, Figure 5). Turn off the air supply by lifting the shut
-
off valve button (1, Figures 7 & 8) or set air pressure to 0 bar using the pressure regulator (2, Figures 7 &
8) and the pressure gauge (3, Figures 7 & 8). Disconnect the M12 cable (7, Figures 5 & 6) from the pump.
Any residual pressure in the system when opening or disconnecting components may cause components
to be thrown or lubricant to spray, causing injury to people or damage to the environment.
WARNING
Pressurised lubricant
The pressure in the pneumatic system must be regulated so that the pressure at the pumping centre can-
not under any circumstances exceed 300 bar (4,350 psi/30 MPa). A higher pressure may damage the sys-
tem components and cause injury to people or damage to the environment.
ATTENTION
Make sure that the surroundings are clean. Make sure that no impurities enter the pump, the follower
plate or the lubricant barrel. Impurities may cause damage to the lubrication system or the machine or
device being lubricated.

20
8.2.1 Maxilube with ECO lid set
1 Ensure that the surroundings of the pumping centre are clean. Impurities in the system prevent trouble-
free operation and cause damage at the lubrication point.
2 Check the condition of the lubricant barrel. Damages on the surface prevent the follower plate from being
lowered (3, Figure 5).
3 Remove the barrel’s original lid and press the follower plate (3, Figure 5) closely on top of the lubricant in
the barrel. Make sure that air is removed from below the follower plate and that the central unit (suction
head) of the follower plate starts to fill with lubricant.
4 Place the lid (1, Figure 5) on top of the lubricant barrel. Fasten the lid onto the lubricant barrel with wing
screws.
5 Pass the pump through the lid onto the suction port of the follower plate. Make sure that the pump is
firmly attached to the air follower plate.
6 Fasten the pressure air hose from the pressure air regulator to the bottom plate connection A1 (Figure
12).
7 Fasten the lubricant tank hose (5, Figure 5) to the bottom plate and pump connection T (Figure 12).
8 Fasten the grease filter (10, Figure 5) to the bottom plate connection P (Figure 12).
9 Fasten the pressure hose (4, Figure 5) to the pump connection P (Figure 2).
10 Fasten the plug to the tank connection (T) of the pump (Figure 2).
11 Fasten the low-level switch (9 & 10, Figure 2) to the pump.
12 Connect the low-level switch cable (7, Figure 5) to the bottom plate connection D (Figure 12) and the ca-
bles of the channel pressure control units and shut-off valves to the pumping centre as described in the
electrical drawings.
13 Fasten the pressure air hose (6, Figure 5) to the bottom plate connection A2 (Figure 12) and the pressure
air connection (4, Figure 2) of the pump.
14 Set the pressure of the pumping centre's pressure air to 4 bar (60 psi) with the pressure air control device
(2, Figure 7) of the pressure air regulator.
15 Start the pump in manual operation mode of the control unit or with pressure air manual control screw of
pumping centre's solenoid valve group (see Paragraph 9.5 Manual operation). When manual control
screws are used, remove the cover plate and the nut below the plate. After this remove the pumping cen-
tre cover.
16 After the pressure hose is filled, stop the pump and connect the hose to the grease filter (10, Figure 5).
17 Fill the main header with lubricant by starting the pump in manual operation mode of control unit or with
pumping centre's solenoid valve group's manual control screws for pressure air and lubrication lines. Stop
the pump when the header piping has been filled and air has been removed.
18 Remove the plug from the tank connection (6, Figure 2) of the pump and fasten the tank hose (5, Figure
5) to the tank inlet of the line valve T (6, Figure 2).
19 Ensure before connecting the tank hose (5, Figure 5) to the bottom plate connection T that only grease
(no air) is coming out of the hose. If needed, pressurise the system again. Air in the system prevents its
trouble-free operation.
20 Do a test pressurisation of the header piping by increasing the pressure with the pressure control device
at the pumping centre to up to 250 bar (3,600 psi). The pump will stop due to backpressure in 250 bar
(3,600 psi) if there is no air or leakage in the header piping.
21 Set the maximum pressure of the pumping centre with a pressure control device (2, Figure 7). The maxi-
mum pressure of the pumping centre should be set approximately 20% higher than the pressure by which
the pressure control unit acknowledgement pressure is reached. For example, if the acknowledgement
pressure level is reached when the pressure of pumping centre is 170 bar (2,500 psi), the maximum pres-
sure should be set at 200 bar (3,000 psi).
22 Fasten the lid of the pumping centre (Figure 9).