Skil 9135 User manual

SKIL Europe BV - Konijnenberg 60 11/05 2610395398
4825 BD Breda - The Netherlands
ANGLE GRINDER
9135 (F0159135..)
www.skileurope.com
www.skileurope.com
INSTRUCTIONS page 5
INSTRUCTIONS page 7
HINWEISE Seite 10
INSTRUCTIES bladz. 14
INSTRUKTIONER sida 17
INSTRUKTION side 19
ANVISNING side 22
OHJEET sivu 25
INSTRUCCIONES pág. 27
INSTRUÇÕES pág. 30
ISTRUZIONI pag. 33
LEÍRÁS oldal 36
POKYNY strana 40
KILAVUZ sayfa 42
INSTRUKCJA strona 45
ИНСТРУКЦИИ страница 48
ІНСТРУКЦІЯ страница 52
O∆ΗΓΙΕΣ σελιδα 55
INSTRUCØIUNI pagina 59
YKA3AНИЕ страница 62
POKYNY strana 65
UPUTE stranica 68
UPUTSTVA stranica 71
NAVODILA stran 73
KASUTUSJUHEND lehekülg 76
INSTRUKCIJA lappuse 79
INSTRUKCIJA puslapis 82
GB
F
D
NL
S
DK
N
FIN
E
P
I
H
CZ
TR
PL
RU
UA
GR
RO
BG
SK
HR
SCG
SLO
EST
LV
LT
ME77

2
22mm
MAX.
115 mm
MAX.
11000
9135
1600 W
1,8 kg
2
A
4
3
5

3
6
CA
B
D
E
K (not included)
G
H
J
J
F

4
8 9
SKIL Nr. 2610362084
ACCESSORIES
Ø 115 mm
SKIL Nr. 2610362085
Ø 115 mm
SKIL Nr. 2610388766
Clic flange
7a7b7c
0

Angle grinder 9135
INTRODUCTION
●This tool is intended for light grinding, cutting and
deburring metal and stone materials without the use of
water; with the appropriate accessories the tool can also
be used for brushing and sanding
●Do not apply pressure on the tool; let the speed of
the cutting disc do the work
●Read and save this instruction manual 2
TECHNICAL SPECIFICATIONS 1
SAFETY
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains operated
(corded) power tool.
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
GB
5

g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR ANGLE GRINDERS
GENERAL
●Only use this tool for dry grinding/cutting
●Only use the flanges which are supplied with this tool
●This tool should not be used by people under the age of
16 years
●Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
●Use the original SKIL accessories which can be
obtained from your SKIL dealer
●For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
●Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
●Do not use damaged, deformed or vibrating grinding/
cutting discs
●Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
●Protect accessories from impact, shock and grease
●Do not use a grinding/cutting disc that is larger than the
maximum recommended size
●Only use grinding/cutting discs with a hole diameter
which fits mounting flange D 6without play; never use
reducors or adaptors to fit large-hole grinding/cutting
discs
●Never use grinding/cutting discs with a threaded hole, of
which the thread is not long enough to accept the
spindle length of the tool
●Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
●Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
●Only use an extension cord which is intended for
outdour use and equipped with a splashproof coupling-
socket
BEFORE USE
●Before using the tool for the first time, it is recommended
to receive practical information
●Do not work with materials containing asbestos
●Be careful of hidden electrical wires or gas- and water
pipes; check the work area, for instance with a metal
detector
●Be careful when cutting grooves, especially in
supporting walls (slots in supporting walls are subject to
country-specific regulations; these regulations are to be
observed under all circumstances)
●Clamp the workpiece in case it does not remain
stationary from its own weight
●Do not clamp the tool in a vice
●Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
●Wear protective glasses and gloves, hearing
protection 3, a dust mask, and sturdy shoes; when
necessary, also wear an apron
●Always mount auxiliary handle A 6and protective guard
B 6; never use the tool without them
●Be sure tool is switched off when plugging in
DURING USE
●Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
●If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
●Push spindle-lock button G 6only when spindle C 6is
at a standstill
●Keep hands away from rotating accessories
●Keep ventilation slots J 6clear and uncovered
●When grinding metal, sparks are generated; keep other
persons and combustible material from work area
●In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
●In case the cutting disc is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
●In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch H 6
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
●Do not apply pressure on the tool; let the speed of the
cutting disc do the work
●Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
●Before you put down the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
●After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
●Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
●If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
●Mount auxiliary handle A 4
●Adjusting protective guard B 5
! ensure that the closed side of the protective
guard always points to the operator
●Mounting of accessories 6
! disconnect the plug
- clean spindle C and all parts to be mounted
- tighten clamping flange E with spanner F while
pushing spindle-lock button G
- for removing accessories handle vice-versa
6

! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it
●Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
●On/off locking switch H 7
- switch on tool 7a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 7b
- unlock switch/switch off tool 7c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
●Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
●Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
●Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots J 6clear and uncovered
APPLICATION ADVICE
●Instead of flange E 6the ”CLIC” quick-clamping flange
K 6(SKIL accessory 2610388766) can be used;
grinding/cutting discs can then be mounted without the
use of accessory keys
GUARANTEE / ENVIRONMENT
●Always keep tool and cord clean (especially the
ventilation slots)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
●This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
●In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
●Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 0will remind you of this when the need for
disposing occurs
Meuleuse d’angle 9135
INTRODUCTION
●Cet outil sert au meulage, au tronçonnage et à
l'ébarbage léger de pièces en métal et en pierre sans
utiliser de l'eau; combiné avec des accessoires
spécifiques, cet outil peut également servir au brossage
et au ponçage
●Ne jamais appliquez une trop forte pression sur
l'outil; laissez au disque le soin de faire le travail de
par sa propre vitesse
●Lisez et conservez ce manuel d’instruction 2
SPECIFICATIONS TECHNIQUES 1
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez toutes les instructions. Le non-
respect des instructions indiquées ci-après peut entraîner
un choc électrique, un incendie et/ou de graves blessures
sur les personnes. La notion d’«outil électroportatif»
mentionnée par la suite se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement).
1) PLACE DE TRAVAIL
a) Maintenez l’endroit de travail propre et bien éclairé.
Un lieu de travail en désordre ou mal éclairé augmente
le risque d’accidents.
F
7

86
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following
standards or standardized documents: EN 50 144, EN 55 014, in accordance with the provisions of the directives 73/23/EC,
89/336/EC, 98/37/EC.
NOISE/VIBRATION Measured in accordance with EN 50 144 the sound pressure level of this tool is 88 dB(A), the sound power level
101 dB(A), and the vibration 4.4 m/s2(hand-arm method).
CE DÉCLARATION DE CONFORMITÉ Nous déclarons sous notre propre responsabilité que ce produit est en conformité avec les
normes ou documents normalisés suivants: EN 50 144, EN 55 014, conforme aux réglementations 73/23/EC, 89/336/EC, 98/37/EC.
BRUIT/VIBRATION Mesuré selon EN 50 144 le niveau de la pression sonore de cet outil est 88 dB(A), le niveau de la puissance
sonore 101 dB(A), et la vibration 4,4 m/s2(méthode main-bras).
CE KONFORMITÄTSERKLÄRUNG Wir erklären in alleiniger Verantwortung, daß dieses Produkt mit den folgenden Normen oder
normativen Dokumenten übereinstimmt: EN 50 144, EN 55 014, gemäß den Bestimmungen der Richtlinien 73/23/EG, 89/336/EG,
98/37/EG.
GERÄUSCH/VIBRATION Gemessen gemäß EN 50 144 beträgt der Schalldruckpegel dieses Gerätes 88 dB(A), der
Schalleistungspegel 101 dB(A), und die Vibration 4,4 m/s2(Hand-Arm Methode).
CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten:
EN 50 144, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG.
GELUID/VIBRATIE Gemeten volgens EN 50 144 bedraagt het geluidsdrukniveau van deze machine 88 dB(A), het geluidsvermogen-
niveau 101 dB(A), en de vibratie 4,4 m/s2(hand-arm methode).
CE KONFORMITETSFÖRKLARING Vi intygar och ansvarar för, att denna produkt överensstämmer med följande norm och
dokument: EN 50 144, EN 55 014, enl. bestämmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG.
LJUD/VIBRATION Ljudtrycksnivån som uppmätts enligt EN 50 144 är på denna maskin 88 dB(A), ljudeffektnivån 101 dB(A), och
vibration 4,4 m/s2(hand-arm metod).
CE KONFORMITETSERKLÆRING Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende
normer eller normative dokumenter: EN 50 144, EN 55 014, i henhold til bestemmelserne i direktiverne 73/23/EF, 89/336/EF,
98/37/EF. STØJ/VIBRATION Måles efter EN 50 144 er lydtrykniveau af dette værktøj 88 dB(A), lydeffektniveau
101 dB(A), og vibrationsniveauet 4,4 m/s2(hånd-arm metoden).
CE SAMSVARSERKLÆRING Vi erklærer at det er under vårt ansvar at dette produkt er i samsvar med følgende standarder eller
standard- dokumenter: EN 50 144, EN 55 014, i samsvar med reguleringer 73/23/EF, 89/336/EF, 98/37/EF.
STØY/VIBRASJON Målt ifølge EN 50 144 er lydtrykknivået av dette verktøyet 88 dB(A), lydstyrkenivået 101 dB(A), og
vibrasjonsnivået 4,4 m/s2(hånd-arm metode).
CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen
standardien ja standardoimisasiakirjojen vaatimusten mukainen EN 50 144, EN 55 014, seuraavien sääntöjen mukaisesti 73/23/ETY,
89/336/ETY, 98/37/ETY. MELU/TÄRINÄ Mitattuna EN 50 144 mukaan työkalun melutaso on 88 dB(A), yleensä työkalun äänen
voimakkuus on 101 dB(A), ja tärinän voimakkuus 4,4 m/s2(käsi-käsivarsi metodi).
CE DECLARACION DE CONFORMIDAD Declaramos bajo nuestra sola responsabilidad que este producto está en conformidad
con las normas o documentos normalizados siguientes: EN 50 144, EN 55 014, de acuerdo con las regulaciones 73/23/CE,
89/336/CE, 98/37/CE.
RUIDOS/VIBRACIONES Medido según EN 50 144 el nivel de la presión acústica de esta herramienta se eleva a 88 dB(A), el nivel
de la potencia acústica 101 dB(A), y la vibración a 4,4 m/s2(método brazo-mano).
CE DECLARAÇÃO DE CONFIRMIDADE Declaramos sob nossa exclusiva responsabilidade que este producto cumpre as
seguintes normas ou documentos normativos: EN 50 144, EN 55 014, conforme as disposições das directivas 73/23/CE, 89/336/CE,
98/37/CE. RUÍDO/VIBRAÇÕES Medido segundo EN 50 144 o nível de pressão acústica desta ferramenta é 88 dB(A),
o nível de potência acústica 101 dB(A), e a vibração 4,4 m/s2(método braço-mão).
GB
F
D
NL
S
DK
N
FIN
E
P
05 SKIL Europe B.V. A. v.d. Kloot
CE DICHIARAZIONE DI CONFORMITÀ Dichiaramo, assumendo la piena responsabilità di tale dichiarazione, che il prodotto è
conforme alle seguenti normative e ai relativi documenti: EN 50 144, EN 55 014 in base alle prescrizioni delle direttive CE 73/23,
CE 89/336, CE 98/37.
RUMOROSITÀ/VIBRAZIONE Misurato in conformità al EN 50 144 il livello di pressione acustica di questo utensile è 88 dB(A), il
livello di potenza acustica 101 dB(A), e la vibrazione 4,4 m/s2(metodo mano-braccio).
I
CE MINÖSÉGI TANUSITVANY Teljes felelösségünk tudatában kijelentjük, hogy jelen termék a következö szabványoknak vagy
kötelezö hatósági elöírásoknak megfelel: EN 50 144, EN 55 014, a 73/23/EK, 89/336/EK, 98/37/EK elöírásoknak megfelelöen.
ZAJ/REZGÉS Az EN 50 144 alapján végzett mérések szerint ezen készülék hangnyomás szintje 88 dB(A), hangteljesítmény szintje
101 dB(A), a kézre ható rezgésszám 4,4 m/s2.
H
CE STRVZUJÍCÍ PROHLÅ◊ENÍ Potvrzujeme na odpovπdnost, Ωe tento v¥robek odpovídå nåsledujícím normåm nebo normativním
podkladüm: EN 50 144, EN 55 014, podle ustanovení smπrnic 73/23/EG, 89/336/EG, 98/37/EG.
HLUÇNOSTI/VIBRACÍ Mπ®eno podle EN 50 144 çiní tlak hlukové vlny tohoto p®ístroje 88 dB(A),dávka hluçnosti 101 dB(A), a vibrací
4,4 m/s2(metoda ruka-paΩe).
CZ
CE STANDARDIZASYON BEYANI Ye¤ane sorumlu olarak, bu ürünün afla¤ıdaki standartlara veya standart belgelerine uygun
oldu¤unu beyan ederiz: EN 50 144, EN 55 014, yönetmeli¤i hükümleri uyarınca 73/23/EC, 89/336/EC, 98/37/EC.
GÜRÜLTÜ//T‹TREfiIM Ölçülen EN 50 144 göre ses basıncı bu makinanın seviyesi 88 dB(A), çal›flma s›ras›ndaki gürültü
101 dB(A), ve titreflim 4,4 m/s2(el-kol metodu).
TR

87
05 SKIL Europe B.V. A. v.d. Kloot
ЗАЯВЛЕНИЕ О СООТВЕТСТВИИ Мы с полной ответственностыо заявляем, что это изделие соответствует следующим
стандартам или стандартизованным документам: EN 50 144, EN 55 014, в соответсувии с инструкциями 73/23/EC,
89/336/EC, 98/37/EC. ШУМНОСТИ/ВИБРАЦИИ При измерении в соответствии co стандартoм EN 50 144 уровень звукового
давления для этого инструмента составляет 88 дБ (A), уровeнь звуковой мощности - 101 дБ (A), и вибрации -
4,4 м/с2(по методу для рук).
RU
CE ВІДПОВІДНІСТЬ Ми заявляємо, що відповідність даного продукту наступним стандартам і регулюючим документам
повністю нашою відповідальністю: EN 50 144, EN 55 014, відповідно до положень директив 73/23/ЄС, 89/336/ЄС, 98/37/ЄС.
ШУМ/ВІБРАЦІЯ Зміряний відповідно до EN 50 144 рівень тиску звуку даного інструменту 88 дБ(А), потужність звуку 101
дБ(А), i вібрація 4,4 м/с2(ручна методика).
UA
CE ∆ΗΛΩΣΗ ΣYMBATOTΗΤΑΣ ∆ηλούµε υπευθύνως τι το προϊν αυτ είναι κατασκευασµένο σύµφωνα µε τους εξής
κανονισµούς ή κατασκευαστικές συστάσεις: EN 50 144, EN 55 014, κατά τις διατάξεις των κανονισµών της Κοινής Αγοράς
73/23/EK, 89/336/EK, 98/37/EK. ΘΟΡYΒΟ/ΚΡΑ∆ΑΣΜΟYΣ Μετρηµένη σύµφωνα µε EN 50 144 η στάθµη ακουστικής πίεσης
αυτού του εργαλείου ανέρχεται σε 88 dB(A),η στάθµη ηχητικής ισχύoς σε 101 dB(A), και ο κραδασµς σε 4,4 m/s2(µεθοδος
χειρς/βραχίονα).
GR
DECLARAØIE DE CONFORMITATE CE Declaråm pe proprie råspundere cå acest product este conform cu urmåtoarele standarde
sau documente standardizate: EN 50 144, EN 55 014, în conformitate cu regulile 73/23/EC, 89/336/EC, 98/37/EC.
ZGOMOT/VIBRAØII Måsurat în conformitate cu EN 50 144 nivelul de presiune a sunetului generat de acest instrument este de
88 dB(A),nivelul de putere a sunetului 101 dB(A), iar nivelul vibraøiilor 4,4 m/s2(metoda mînå - braø).
RO
CE ДЕKЛАPAЦИЯ ЗA CБOTВETCTBИE Декларираме на изцяло наша отговорност, че това изделие е съобразено със
следните стандарти или стандартизирани документи: EN 50 144, EN 55 014, в съответствие с нормативната уредба на
73/23/EG, 89/336/EG, 98/37/EG.
ШУМ/ВИБPAЦИИ Измерено в съответствие с EN 50 144 нивото на звуково налягане на този инструмент е 88 dB(A),нивото
на звукова мощност е 101 dB(A), а вибрациите са 4,4 m/s2(метод ръка-рамо).
BG
CE IZJAVA O USKLA ĐENOSTI Izjavljujemo uz punu odgovornost da je ovaj proizvod usklađen sa slijedeçim normama i
normativnim dokumentima: EN 50 144, EN 55 014, prema odredbama smjernica 73/23/EG, 89/336/EG, 98/37/EG.
BUCI/VIBRACIJAMA Mjereno prema EN 50 144, prag zvuãnog tlaka ovog elektriãnog alata iznosi 88 dB(A), jakost zvuka
101 dB(A), a vibracija 4,4 m/s2(postupkom na ‰aci-ruci).
HR
CE IZJAVA O USKLA ĐENOSTI Pod punom odgovorno‰çu izjavljujemo da je ovaj proizvod usklađen sa sledeçim standardima ili
standardizovanim dokumentima: EN 50 144, EN 55 014, u skladu sa odredbama smernica 73/23/EG, 89/336/EG, 98/37/EG.
BUKA/VIBRACIJE Mereno u skladu sa EN 50 144, nivo pritiska zvuka ovog alata iznosi 88 dB(A), jaãina zvuka
101 dB(A), a vibracija 4,4 m/s2(mereno metodom na ‰aci-ruci).
SCG
IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti:
EN 50 144, EN 55 014, v skladu s predpisi navodil 73/23/EG, 89/336/EG, 98/37/EG.
HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 50 144 je raven zvoãnega pritiska za to orodje 88 dB(A), jakosti zvoka
101 dB(A), in vibracija 4,4 m/s2 (metoda ‘dlan-roka’).
SLO
CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab järgmistele standarditele või
normdokumentidele: EN 50 144, EN 55 014 vastavalt direktiivide 73/23/EÜ, 89/336/EÜ, 98/37/EÜ nõuetele.
MÜRA/VIBRATSIOON Vastavalt kooskõlas normiga EN 50 144 läbi viidud mõõtmistele on antud seadme helirõhk 88 dB(A),
helitugevus 101 dB(A), ja vibratsioon 4,4 m/s2(käe-randme-meetod).
EST
CE DEKLARÅCIJA PAR ATBILST±BU STANDARTIEM Mïs ar pilnu atbild¥bu pazi¿ojam, ka ‰is izstrÇdÇjums atbilst standartiem vai
standartizÇcijas dokumentiem EN 50 144, EN 55 014 un ir saska¿Ç ar direkt¥vÇm 73/23/EG, 89/336/EG, 98/37/EG.
TROKSNIS/VIBRÅCIJA Saska¿Ç ar standartu EN 50 144 noteiktais instrumenta rad¥tÇ trok‰¿a ska¿as spiediena l¥menis ir
88 dB(A), ska¿as jaudas l¥menis ir 101 dB (A), un vibrÇcijas intensitÇte ir 4,4 m/s2(strÇdÇjot rokas reÏ¥mÇ).
LV
CE KOKYBñS ATITIKTIES DEKLARACIJA Mes atsakingai parei‰kiame, kad ‰is gaminys atitinka tokius standartus ir normatyvinius
dokumentus: EN 50 144, EN 55 014 pagal EEB reglament˜ 73/23/EG, 89/336/EG, 98/37/EG nuostatas.
TRIUK·MINGUMAS/VIBRACIJA ·io prietaiso triuk‰mingumas buvo i‰matuotas pagal EN 50 144 reikalavimus keliamo triuk‰mo
garso slògio lygis siekia 88 dB(A), akustinio galingumo lygis 101 dB(A), ir vibracijos pagreitis rankos pla‰takos srityje tipiniu atveju yra
maÏesnis, kaip 4,4 m/s2.
LT
CE PREHLÁSENIE O ZHODE Vÿhradne na na√u vlastnú zodpovednos† prehlasujeme, Ωe tento vÿrobok zodpovedá nasledujúcim
normám alebo normovanÿm dokumentom: EN 50 144, EN 55 014, v súlade s predpismi 73/23/EC, 89/336/EC, 98/37/EC.
HLUKU/VIBRÁCIÁCH Merané pod¬a EN 50 144 je úroveµ akustického tlaku tohto nástroja 88 dB(A), úroveµ akustického vÿkonu je
101 dB(A) a vibrácie sú 4,4 m/s2(metóda ruka - paΩa).
SK
OÂWIADCZENIE ZGODNOÂCI CE Niniejszym oÊwiadczamy ponoszàc osobistà odpowiedzialnoÊç, ˝e produkt wykonany jest zgodnie
z nast´pujàcymi normami i dokumentami normalizujàcymi: EN 50 144, EN 55 014, z godnie z wytycznymi 73/23/WE, 89/336/WE,
98/37/WE. HA¸ASU/WIBRACJE Pomiarów dokonano zgodnie z normà EN 50 144 ciÊnienie akustyczne narz´dzia wynosi 88 dB(A),
poziom mocy akustycznej 101 dB(A), zaÊ wibracje 4,4 m/s2(metoda d∏oƒ-r´ka).
PL