Skope Pegasus PG100HC-2 User manual

Service Manual MAN6787S Rev. 1.0 Feb. 2009 edition
PG100HC-2
PG250HC-2
PG400HC-2
PG550HC-2
SKOPE PEGASUS
PG100/250/400/550HC-2
Horizontal Chiller

SKOPE Pegasus Horizontal Chiller
SERVICE MANUAL
i
SKOPE PEGASUS Horizontal Chiller
PG100/250/400/550HC-2
Service Manual
MAN6787S
Rev. 1.0 Feb. 2009 edition.
Copyright © 2009
SKOPE Industries Limited.
All rights reserved.
SKOPE Industries Limited reserve the right to alter specifications without
notice.
is a registered trade mark of SKOPE Industries Limited.
TRADE MARK INFRINGEMENT
The SKOPE trade mark on this product is infringed if the owner, for the time
being, does any of the following:
• Applies the trade mark to the product after their state, condition, get-up
or packaging has been altered in any manner
• Alters, removes (including part removal) or obliterates (including part
obliteration) the trade mark on the product
• Applies any other trade mark to the product
• Adds to the product any written material that is likely to damage the
reputation of the trade mark
Notice of the above contractual obligations passes to:
• Successors or assigns of the buyer
• Future owners of the product

SKOPE Pegasus Horizontal Chiller
TABLE OF CONTENTS ii
TABLE OF CONTENTS
SPECIFICATIONS
Cabinet and Refrigeration Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTALLATION
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fitting the Legs or Castors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Positioning the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shelving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cabinet Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ELECTRONIC CONTROLLER
Controller Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Controller Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Temperature Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Controller Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Default Programme Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Controller Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Controller Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
HACCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
REFRIGERATION UNIT
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Servicing and Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
WIRING
Cabinet Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Refrigeration Unit Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4SKOPE Pegasus Horizontal Chiller
TABLE OF CONTENTS -
SPARE PARTS
Cabinet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Refrigeration Unit Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wiring Junction Box Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
REPLACEMENT PROCEDURES
Refrigeration Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Wiring Junction Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Electronic Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
TROUBLESHOOTING
Cabinet and Refrigeration Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
MAINTENANCE
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
SKOPE Contact Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

5
SKOPE Pegasus Horizontal Chiller
SPECIFICATIONS - Cabinet and Refrigeration Unit
SPECIFICATIONS
Cabinet and Refrigeration Unit
Table 1: Specifications
Cabinet Construction
Exterior / Interior: Stainless steel
Insulation: 50mm thick, polyurethane foam
Cyclo-iso Pentane blowing agent: C5H10/C5H12
Dimensions
Model: PG100HC-2 PG250HC-2 PG400HC-2 PG550HC-2
Height: 716mm 716mm 716mm 716mm
Width: 863mm 1331mm 1799mm 2267mm
Depth: 680mm 680mm 680mm 680mm
Floor area: 0.58m20.90m21.22m21.54m2
Internal volume: 110 litres 260 litres 410 litres 560 litres
Refrigeration Unit
Electronic controlled, side mounted, removable, integral refrigeration unit
Model: UE50ACD UE50ACD UE60ACD UE60ACD
Controller Carel ir33 electronic controller (470 bn1 programme)
Compressor: Electrolux GLY90RA (9cc) Danfoss SC12G (12cc)
Capacity: 366 Watt 464 Watt
Refrigerant: R134a R134a
Charge: 340 g 525 g
Capilliary: 1.3mm I.D. x 2.6m 1.3mm I.D. x 2.8m
Electrical
230-240 Volts a.c. 50 Hz, single phase power supply
Run Amps: 1.94 Amp 2.05 Amp 2.58 Amp 2.72 Amp
Lighting
15 Watt OSRAM (PYGMY CL 15 E14) light bulb - door activated
1 x 15 Watt 1 x 15 Watt 2 x 15 Watt 3 x 15 Watt
Door/s
Self-closing, hinged, solid foam filled stainless steel door/s, with individual key lock
Shelves
Two levels of non-tip, adjustable tray slides and/or shelves per door

6SKOPE Pegasus Horizontal Chiller
INSTALLATION - Safety Information
INSTALLATION
Safety Information
When using any electrical appliance, safety precautions should always be
observed. Read these instructions carefully and retain for future reference.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
•DoNOT use this appliance for other than its intended use.
•DoNOT cover the grilles or block the entry or exhaust of airflow by placing
objects up against the refrigeration unit.
•DoNOT probe any opening.
• Only use this appliance with voltage specified on the rating label.
• Ensure adequate ventilation of the SKOPE refrigeration unit.
• Be careful not to touch moving parts and hot surfaces.
• Regulations require that all electrical work be carried out by authorised
persons. For your own safety, and that of others, ensure this is done.
• If the supply cord becomes damaged, it must be replaced by a SKOPE
authorised service agent, or similarly qualified person, in order to avoid a
hazard.
• If the refrigeration unit is required to be installed or removed from the cabinet,
ensure all necessary safety precautions are observed.
• This chiller is not designed to be stable in motion. Exercise caution when
moving or transporting this chiller.
Caution:
Disconnect the cabinet from the mains power supply before attempting any
cleaning or maintenance.

7
SKOPE Pegasus Horizontal Chiller
INSTALLATION - Fitting the Legs or Castors
Fitting the Legs or Castors
Packed inside the cabinet is a set of adjustable height legs and a set of adjustable
height castors. Either of these sets can be fitted to the cabinet depending on
specific height and manoeuvrability requirements. The legs or castors should be
fitted to the base of the cabinet before final positioning of the chiller.
Adjustable Legs
The adjustable legs screw into the castor mounting plates attached to the bottom of
the cabinet. The adjustable legs can adjust the cabinet height up to 30mm.
To adjust the height of each leg, turn the black plastic foot at the bottom of the leg
counter-clockwise to raise the height or clockwise to lower (see Figure 2 below).
Figure 1: Castor Mounting Plate Figure 2: Adjustable Leg

8SKOPE Pegasus Horizontal Chiller
INSTALLATION - Fitting the Legs or Castors
Adjustable Castors
The adjustable castors screw into the castor mounting plates attached to the bottom
of the cabinet. The two lockable castors should be fitted to the front of the cabinet
(see Figure 3 below) and the non-locking castors fitted to the rear (see Figure 4
below). The adjustable castors can adjust the cabinet height up to 15mm.
To adjust the height of each castor, loosen the lock nut and turn the castor counter-
clockwise to raise the height or clockwise to lower. Re-tighten each lock nut after
final adjustment has been made.
Castor Mounting Plates
If the chiller is intended to be mounted on a plinth, the castor mounting plates
attached to the bottom of the cabinet can be removed to provide a flat bottom. Each
castor mounting plate is held in place by four pozi-drive hexagon head screws (see
Figure 1 on page 7).
Figure 3:
Lockable Castor (front)
Figure 4:
Non-Locking Castor (rear)
Castor Lock Nut
Castor Mounting Plate

9
SKOPE Pegasus Horizontal Chiller
INSTALLATION - Positioning the Cabinet
Positioning the Cabinet
Location
When positioning the cabinet, avoid direct sunlight and warm draughts etc. The
cabinet must NOT be situated where it is affected by warm or hot air from adjacent
equipment, as this will compromise the airflow and performance of the chiller.
The cabinet must be positioned on a level surface for the doors to shut and seal
correctly, and to prevent the condensate tray from overflowing. Adequate allowance
should be made for door opening.
Always ensure that the top of the cabinet is shielded from impact and moisture, with
either a SKOPE provided bench top or with a custom or existing bench top.
Ventilation
For efficient operation of the chiller, it is essential that adequate ventilation be
provided around the front of the refrigeration unit. Normal operating conditions
should not exceed 40°C at 65% RH.
It is critical that the hot refrigeration exhaust air is not restricted and that it can easily
flow out and away from the front of the cabinet.
Never store cardboard cartons or other items in front of the refrigeration unit. The
ventilation slots in the unit front cover must be kept clear at all times.
When installing the cabinet:
• Avoid direct sunlight and warm draughts etc.
• Ensure adequate ventilation around the front of the refrigeration unit.
• Allow adequate space for the door/s to open fully.
• Ensure the cabinet is positioned on a level surface so the door/s shut and seal
correctly and to prevent the condensate tray from overflowing.
• The self-closing door/s have internal torsion bars, pretensioned at the factory,
and should not require any further adjustment.
• Do not overload the power supply. See the rating label inside the cabinet for
power supply and current draw.
Warning:
The ventilation slots in the unit front cover must be kept clear at all times.

10 SKOPE Pegasus Horizontal Chiller
INSTALLATION - Positioning the Cabinet
Power Supply
The chiller is supplied with a 1.8m flexible power cord and plug, which for transit
purposes is located inside a compartment in the rear of the cabinet (see Figure 5
below).
Before final positioning of the chiller, pull the power cord out from the rear
compartment and connect to the power supply. For convenience, any surplus cord
length may be left inside the cabinet compartment.
Once the chiller has been installed it can be disconnected from the mains power
supply by turning off the cabinet isolating switch and unplugging the unit supply
isolation flex, located inside the refrigeration unit compartment (see Figure 6
below).
Warning:
Do NOT overload the power supply. See the rating label inside the cabinet for
power supply and current draw.
Figure 5: Power Cord
Power Cord
Cabinet Rear
Compartment
Cabinet Isolating Switch
Unit Supply Isolation Flex
Figure 6: Isolating Switch
Power Cord Storage

11
SKOPE Pegasus Horizontal Chiller
INSTALLATION - Shelving
Shelving
The cabinet is supplied with two sets of shelves and shelf support brackets per door.
The shelves can be positioned at different heights to suit various products.
To fit the cabinet shelves:
1. Unpack the shelving items from inside the cabinet.
2. Establish the desired position for each of the shelves, based on the height of
the product intended to go on each shelf.
3. Fit the shelf support brackets into the corresponding slots in both the front
and back support rails. Each shelf requires two support brackets.
4. Slide each shelf into the support
brackets.

12 SKOPE Pegasus Horizontal Chiller
INSTALLATION - Shelving
Loading Product
The chiller should be left running for 30 minutes before loading with product.
When loading the cabinet shelves with product:
• Allow air space around all the product, to ensure even cooling and efficient
operation of the chiller.
• Do not allow products to overhang the front of the shelf as this could prevent
the doors from shutting. Leave an airspace of at least 75mm above product
loaded on the top shelf.
• Do not exceed a maximum loading of 20kg per shelf.
• Remove some product if the shelves are flexing or bending.

13
SKOPE Pegasus Horizontal Chiller
INSTALLATION - Cabinet Operation
Cabinet Operation
Connect the cabinet to the mains power supply and check operation of the
refrigeration unit, electronic controller and cabinet lighting.
Ensure the cabinet isolating switch, located inside the refrigeration unit
compartment, is turned on (see Figure 6 on page 10).
Refrigeration Unit
The compressor and the condenser and evaporator fans should all operate within
two minutes from the time the cabinet is plugged in. This may be verified by listening
for compressor switch-on and checking for air movement inside the cabinet. The
compressor and condenser fan will switch off when the cabinet internal temperature
reaches 2°C.
Electronic Controller
When the cabinet is connected to the power supply, the electronic controller will
display the current cabinet temperature. The compressor LED will indicate the
compressor is operating and the evaporator fan LED will normally come on
within 2 minutes (see page 14 for controller display).
To ensure efficient operation, the electronic controller forces 6 hourly defrosts.
During the defrost cycle, the compressor and condenser fan switch off and the
evaporator fan stays on.
Cabinet Lighting
The interior lighting will go on when a cabinet door is opened. The only time that a
light should not turn on is either if a bulb is faulty or the ‘CHt’ high temperature
shutdown alarm has been activated (see pages 22-23 for controller alarms). To
replace a light bulb see service instructions on page 62.
HACCP
If Hazard Analysis Critical Control (HACCP) functions are required, to monitor food
storage temperature, please contact SKOPE to arrange for an authorised SKOPE
service technician to setup the electronic controller (see pages 24-25).
Important:
If the cabinet has been on its back, leave for 30 minutes before running.

14 SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Controller Display
ELECTRONIC CONTROLLER
Controller Display
Table 2: Controller Functions
ITEM ICON FUNCTION
1Prg / mute: n.a.
2UP / aux: To scroll settings UP (in programme mode).
3Set: If pressed for more than 2 seconds displays and / or enables changing the
temperature setpoint (see page 15).
4DOWN / def: To scroll settings DOWN (in programme mode). Press for more than
5 seconds to initiate manual defrost.
5COMPRESSOR: ON when the compressor and condenser fan starts. Flashes
when activation of the compressor is temporarily delayed.
6FAN: ON when the internal cabinet fans are activated. Flashes when activation of
the fans is temporarily delayed.
7DEFROST: ON when the defrost is activated. Flashes when the activation of the
defrost is temporarily delayed due to procedures in progress.
8AUX: n.a.
9ALARM: Flashes in the event of alarms and when a door is opened.
10 CLOCK: n.a.
11 LIGHT: n.a.
12 SERVICE: Flashes in the event of malfunctions.
13 HACCP: On if HACCP function is enabled. Flashes if HACCP alarm has occurred.
14 CONTINUOUS CYCLE: n.a.
Figure 7: Controller Display

15
SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Controller Overview
Controller Overview
Function
The CAREL ir33 electronic controller controls and displays the internal cabinet
temperature. The preset temperature setting controls the product temperature
between 1°C and 4°C. The electronic controller also signals temperature alarms
(see Table 8 on pages 22-23).
Operation
For general operation, the electronic controller requires no initial setup or additional
programming. When the cabinet is connected to the power supply, the electronic
controller will display the current cabinet temperature. The compressor LED will
indicate the compressor is operating and the evaporator fan LED will normally
come on within 2 minutes (see Figure 7 for controller display).
Temperature Setpoint
The chiller temperature setpoint is factory set at 2.0°C. If necessary the standard
setting can be adjusted between 1.5°C and 3.5°C.
SKOPE do not recommend that the setpoint be changed unless it is absolutely
necessary, and then only by small increments at a time.
To view and adjust the temperature setpoint:
Table 3: Temperature Setpoint Adjustment
1. To view the setpoint:
Press and hold the key for 2 seconds, until
the setpoint value flashes.
2. To adjust the setpoint:
Press either the or keys to display the
required setpoint value.
3. Press the key again to memorise the new
setpoint value. If this is not done within 60
seconds changes will be lost and you will need to
repeat the above procedure.

16 SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Controller Reset
Controller Reset
To delete programme modifications and reset the controller to SKOPE default
programme, a ‘Controller Reset’ must be performed. The electronic controller must
never be left in programme mode ‘bn0’, as failure will occur.
To Perform a Controller Reset:
Table 4: Controller Reset
Warning:
The electronic controller must never be left in programme mode ‘bn0’,
as failure will occur.
1. Unplug the cabinet from the mains power supply.
2. Press and hold the key while
plugging the cabinet into the
power supply (this may require
two people). After a few seconds
the controller is reset and
programme mode ‘bn0’ is
displayed.
3. Press the or keys to
select ‘bn1’ for SKOPE default
programme.
4. Immediately press the key to confirm the
preferred programme. If not confirmed within 60
seconds the chiller will remain in programme mode
‘bn0’ (and cause failure). If this occurs, repeat the
above procedure.

17
SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Default Programme Configuration
Default Programme Configuration
Factory Default Configuration of the controller is set by SKOPE to a specific SKOPE
Product. The factory default cannot be altered in the field. A label on the controller
box indicates the default programme configuration number (see page 29).
Basic Adjustment
Before commencing any servicing the refrigeration technician should check with the
customer for requirements and any applied controller changes (made by the
customer). The controller programmable operating mode is flexible and may be
customised to incorporate customer specific requirements.
Field Adjustable Programming
Within each program are field adjustable (Type ‘C’) parameters. Non-useful
parameters are hidden. Changes to SKOPE factory default programmes are not
recommended.
To Access ‘Type C’ Parameters:
Table 5: Accessing ‘Type C’ Parameters
1. Press the key and keys
together for more than 5 seconds.
The display will show the number
‘00’, representing the password
prompt.
2. Press the or keys until
displaying the password number
‘66’.
3. Confirm by pressing the key.
The display will show the code of
the first modifiable type ‘C’
parameter.

18 SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Default Programme Configuration
To Modify ‘Type C’ Parameters:
Table 6: Modifying ‘Type C’ Parameters
1. Press the or keys until reaching the
parameter to be modified. When scrolling, an icon
appears on the display representing the category the
parameter belongs to.
2. Alternatively, press the key to display a menu that
is used to quickly access the group of parameters to
be modified.
3. Scroll the menu with the or keys. The display
shows the codes of the various categories of
parameters.
4. When having reached the desired category, press
the key to move directly to the first parameter in
the category.
5. At this stage, continue to scroll the parameters or
press the key to return to the categories.
6. Press the key to display the value associated with
the parameter.
7. Increase or decrease the value using
the or keys respectively.
8. Press the key to temporarily save the new value
and return to the display of the parameter code.

19
SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Default Programme Configuration
Table 6: Modifying ‘Type C’ Parameters - continued
9. Repeat the operations from point 1 or point 2 on the
previous page.
10. If the parameter has sub-parameters, press
the key to display the first sub-parameter.
11. Press the or keys to display all the sub-
parameters.
12. Press the key to display the associated value.
13. Increase or decrease the value using
the or keys respectively.
14. Press the key to temporarily save the new value
and return to the display of the sub-parameter code.
15. Press the key to return to the display of the parent
parameter.
16. Press the key for more than five seconds to store
the new values of the modified parameters.

20 SKOPE Pegasus Horizontal Chiller
ELECTRONIC CONTROLLER - Controller Parameters
Controller Parameters
Programme P-470 bn1
Horizontal and Vertical Chiller - Integral and Remote
Table 7: Programme P-470 bn1
Table 7: Controller Parameters P-470 bn1 - continued
Carel Custom Controller - ELZ3333
IRSKC0HF325
Parameter Program Sheet for
BN2 BN3 BN6
P
e
g
asus - 470 - Chiller
(
Vert & Horizontal
)
- B
N
Access
Descri
p
tion of Parameter
Level Min Max Password Parameter (PS) = 66 30
/2 4- C 1 15 Measurement stabilit
y
4
/3 8 - C 0 15 Probe displa
y
speed 0
/6 0 flag F 01
Decimal point (0 = decimal point)
0
/tE 0 - C 0 6 Sensor shown on remote display
0
/P 0 - C 0 2 Type of probe (0= standard Carel NTC)
0
/A2 2 - C 0 5 Probe 2 configuration (eg 2=evap,3=cond)
2
/A3 3 - C 0 5 Probe 3 configuration (eg 2=evap,3=cond)
0
/c1 0 °C C -20°C 20°C Calibration of probe 1
0
St 2 °C F r1 r2 Temperature set point
0
rd 2 °C C 0.1°C 20°C Controller differential
2
r1 1 °C C -50°C r2 Minimum Set Point allowed
-50
r2 3.5 °C C r1 200°C Maximum Set Point allowed
60
r5 1 flag C 0 1 Enable temperature monitoring (NOT related to HACCP)
0
rt 0 Hours F 0 999 Temperature monitoring interval
0
rH 0 °C F - - Max temperature recorded during period rt
0
rL 0 °C F - - Min temperature recorded during period rt
0
c2 5 Mins C 0 15 Minimum compressor OFF time
0
c3 5 Mins C 0 15 Minimum compressor ON time
0
c4 5 Mins C 0 100 Duty setting
0
dI 6 Hours C 0 250 Interval between defrosts (if not using real time)
8
dt1 4.5 °C C -50 200 End defrost temperature, (if d0 = 0 or 1)
4
dtn 5 °C C -50 200 End defrost temperature, in Night Mode
0
dP1 60 Minutes C 1 250 Maximum defrost duration
30
d6 1 - C 0 2 Display during def.(0=dF (flash),1=locked,2=dEF)
1
dd 1 Minutes C 0 15 Dripping time after defrost
2
d8 1 Hours C 0 15 Bypass alarms after defrost
1
d8d 120 Minutes C 0 250 Graduations for Door Open Notification / Alarm (Secs)
0
A0 2 °C C 0°C 20°C Alarm and fan differential
2
AL -5 °C C -50°C 200°C Low alarm temp (see A1 for absol. or relative)
0
AH 20 °C C -50°C 200°C High alarm temp (see A1 for absol. or relative)
0
AHO 55 °C C -50°C 200°C High Ambient alarm temp (see A1 for absol. or rel.)
0
Ad 120 Minutes C 0 250 Low and high temperature alarm delay
120
A5 0 - C 0 15 Configuration of digital input 2
0
A9 9 - C 0 15 Configuration of digital input 3
0
Ac 66 °C C 0.0°C 200°C Condenser Alarm Shutdown Set Point
70
AE 11 °C C 0.1°C 20°C Cond. Warning (Divided by 2 - i.e. 10 = 5K diff from Ac)
10
F0 2 flag C 05
Evap Fan management
0
F1 20 °C C -50°C 200°C Fan start temperature
5
Fon 2 Minutes C 0 15 Time of Evap Fan On (when FO = 4)
0
FoF 2 Minutes C 0 15 Time of Evap Fan Off (when FO = 4)
0
H0 1 - C 0 207 Serial address
1
H2 1 flag C 1 6 Keypad and IR locking (1 = unlocked)
1
H4 0 flag C 0 1 Disable buzzer (0=enabled, 1 = disabled)
0
H6 8 - C 0 255 Buttons to lock when keypad locked
0
H10 0 flag C 0 15 Configuration relay AUX3
0
H17 0 flag C 0 1 Enable Probe Quick Function (0 = Enabled)
0
H18 0 flag C 0 1 Real Time Clock (RTC) Status (1 = Enabled)
0
H19 0 flag C 0 1 RTC controller alarm (1 = Enabled)
1
HAn 0 - C 0 15 Number of events HA occured
0
HA 0 - C - - Data/Time of most recent event HA
0
HA1 0 - C - - Data/Time of last event -1 HA
0
HA2 0 - C - - Data/Time of last event -2 HA
0
HFn 0 - C - - Number of events HF occured
0
HF 0 - C - - Data/Time of most recent event HF
0
HF1 0 - C - - Data/Time of last event -1 HF
0
HF2 0 - C - - Data/Time of last event -2 HF
0
HOn 0 - C - - Number of events AHO occured
0
HO 0 - C - - Data/Time of most recent event AHO
0
Htd 0 Minutes C 0 250 HACCP Activation (0 = off, >0 = ON & delay)
0
ton Set - C - - Day Mode Start (days of week, hour, minute)
0
tof Set - C - - Night Mode Start (days of week, hour, minute)
0
tc Set - C - - RTC-current time (Yr, Mth, Day of Mth, Day of Wk, Hr, Min) 0
Skope Industries Limited - Electronic Controller Parameter Sheet
Available Controller Program Modes
Program No.
Revision No.
470
BN4
Program Mode
Standard ModeNo PRN Issued
PRN Number
Date Latest Revision
20 July 2010
Date Created
7 July 2008
Defrost Parameters
Alarm Parameters
Fan Parameters
Configuration Parameters
HACCP Parameters
Real Time Clock Parameters
Recorded Parameters
Control Parameters
Compressor Parameters
BN5BN1 1.2
Display Range
Standard Mode
Settings
Probe Parameters