Sky Angel 3D cap-232 User instructions

Assembly and Operating Manual
Specification:
*Length: 25-9/10"(655mm)
*Wing Span: 29-3/5"(750mm)
*Flying Weight: 15-9/10 oz (450g)
3D cap-232

Assembly and Operating Manual 3D cap-232
2
Dear customer,
Congratulations on your choice of a
factory-assembled model aircraft from the
SKYANGEL 3D range and thank you for placing
your trust in us.
The model can very quickly be completed ready to
fly. Please read right through these instructions
and the separate information sheets before
attempting to assemble and fly the model, as this
will make it much easier to complete the tasks
required.
All directions, such as “right-hand”, are as seen
from the tail of the model, looking forward.
Notes on the power system
Abrushless outrunner motor, propeller and spinner
are factory-installed.
The motor is connected to the speed controller,
ready to use, and the controller is correctly set up
at the factory.
To complete the power system all you have to do
is connect the LiPo flight battery.
The radio control system
For this model you require a radio control system
with at least four channels. We particularly
recommend 2.4 GHz systems.
The receiving system is powered by the speed
controller’s integral BEC system.
Before you check the model’s working systems,
set the control surfaces to neutral from the
transmitter (transmitter sticks and trims central).
Before operating the model always move the
throttle stick to the “motor stopped” position before
switching the transmitter on. Only then connect the
flight battery.
To switch off, first disconnect the flight pack from
the speed controller, and only then switch the
transmitter off.
Glued joints, suitable adhesives
Foam safe epoxy is recommended and available
from most reputable model retail shops.
Trial-fit all parts “dry” before applying glue.
Follow the recommended curing time suggested
by the glue manufacturer. Allow the glue to fully
cure (harden) to the point where the joint can be
placed under stress.
Kit contents
Fuselage, complete with motor, speed controller
and servo.
Integral wing panels with L.H / R.H. ailerons and
servos
Horizontal Tail plane and elevator
Tail plane and elevator Fin
Factory-fitted propeller and spinner
2 X Aileron pushrod, one Z-bend
2 X Elevator pushrod, one Z-bend.
1 X Vertical pushrod, one Z-bend
1 X Y-lead
5X Control surface horn
1 X 3S1P LiPo battery，950 mAh, 25C

Assembly and Operating Manual 3D cap-232
3
Fig. 1
- Tighten the control rod in horizon tail with screw.
Fig. 2
-Reverse the procedure to the right wing. The photo
shows the finished view.
Fig. 3
-Tighten the control rod in vertical tail with screw.
Fig. 4
- Photo shows the finished view.
1
2
3 4

Assembly and Operating Manual 3D cap-232
4
Fig. 5
-Tighten the control rod in wing set with screw.
Fig.6
- Photo shows the finished view
Figs. 7
- Reverse the procedure to the left wing. The photo
shows the finished view.
Figs.8
-Assemble the taildraggers to the hole in the
fuselage
5
6
7
8

Assembly and Operating Manual 3D cap-232
5
Figs. 9
-Assemble the taildraggers to the steering hole.
Figs. 10
-Apply glue to vertical tail .
Figs. 11
- Assemble the vertical tail and taildraggers to the
fuselage.
Figs. 12
-Photo shows the vertical tail and taildraggers
assembled on the fuselage.
10
11 12
9

Assembly and Operating Manual 3D cap-232
6
Figs. 13
-Apply glue to the fuselage .
Figs. 14
-Apply glue to the horizon tail.
Figs. 15
-Photo shows the horizon tail settled in the fuselage.
Figs. 16
- Connect the horizon tail pushrod cullet to control
rod arm .
13
14
15 16

Assembly and Operating Manual 3D cap-232
7
Figs. 17
-Reverse the procedure to the left side. The photo
shows the finished view.
Figs.18
-Connect the vertical tail pushrod collet to control
rod arm.
Figs.19
-Photo shows the finished view.
Figs. 20
- Connect the wing panel push rod to the servo arm
at first hole.
1817
19 20

Assembly and Operating Manual 3D cap-232
8
Figs. 21
-Connect the wing panel push rod to control rod
arm.
Figs.22
-Photo shows the finished view .
Figs. 23
- Reverse the procedure to the left wing. The photo
shows the finished view.
Figs. 24
-Assemble the wing panel to fuselage.
24
23
2221

Assembly and Operating Manual 3D cap-232
9
Figs. 25
-Tight the fixup presser with screw.
Figs. 26
-Tight the plastic spinner with screw.
Figs. 27
- Fixed the propeller with screw.
Figs. 28
- Connect to the receiver and place the receiver in
the middle of the fuselage.
25
26
27 28

Assembly and Operating Manual 3D cap-232
10
Figs. 29
- Place the flight battery in the fuselage.
Figs. 30
- Photo shows battery leads connected to the speed
controller.
Figs. 31-32
- Opening and closing the canopy:
The canopy is retained by the cowl at the front,
and by a tongue at the rear
- To open the canopy, slide it forward, raise it at
the rear and lift it off
- Reverse the procedure to replace the canopy.
29 30
31 32