Sky Angel DHC User instructions

Assembly and Operating Manual
DHC
Specification:
*Length: 26-2/5"(670mm)
*WingSpan:39-2/5"(1000MM)
*Flying Weight: 21-9/10 oz .(620g)

Assembly and Operating Manual DHC
2
Dear customer,
Congratulations on your choice of a
factory-assembled model aircraft from the
TRAINER DHC and thank you for placing your
trust in us.
The model can very quickly be completed ready to
fly. Please read right through these instructions
and the separate information sheets before
attempting to assemble and fly the model, as this
will make it much easier to complete the tasks
required.
All directions, such as “right-hand”, are as seen
from the tail of the model, looking forward.
Notes on the power system
Abrushless outrunner motor, propeller and spinner
are factory-installed.
The motor is connected to the speed controller,
ready to use, and the controller is correctly set up
at the factory.
To complete the power system all you have to do
is connect the LiPo flight battery.
The radio control system
For this model you require a radio control system
with at least four channels. We particularly
recommend 2.4 GHz systems.
The receiving system is powered by the speed
controller’s integral BEC system.
Before you check the model’s working systems,
set the control surfaces to neutral from the
transmitter (transmitter sticks and trims central).
Before operating the model always move the
throttle stick to the “motor stopped” position before
switching the transmitter on. Only then connect the
flight battery.
To switch off, first disconnect the flight pack from
the speed controller, and only then switch the
transmitter off.
Glued joints, suitable adhesives
Foam safe epoxy is recommended and available
from most reputable model retail shops.
Trial-fit all parts “dry” before applying glue.
Follow the recommended curing time suggested
by the glue manufacturer. Allow the glue to fully
cure (harden) to the point where the joint can be
placed under stress.
Kit contents
Fuselage, complete with motor, speed controller
and servo.
Integral wing panels with L.H / R.H. ailerons and
servos
Tailplane and elevator
Fin
Factory-fitted propeller and spinner
2 X Aileron pushrod, Two Z-bend
1 X Elevator pushrod, one Z-bend.
1 X Rudder pushrod one Z-bend
1 X Y-lead
4 X Control surface horn
1 X 2S1P LiPo battery，1000 mAh, 20C

Assembly and Operating Manual DHC
3
Figs. 1
- Connect the control rod to horizontal tail ,tighten
it with the screws.
Figs. 2
-Photo shows the finished view.
Fig. 3
-Connect the control rod to vertical tail, tighten it with
the screws.
Fig. 4
-Photo shows the finished view.
1
3
2
4

Assembly and Operating Manual DHC
4
Fig. 5
-Connect the control rod to aileron, tighten it with the
screws.
Fig. 6
- Photo shows the control rods have locked on the
aileron.
Fig. 7
-Reverse the procedure to the left wing. The photo
shows the finished view.
Fig. 8
- Apply glue to the fuselage which will set horizon
tail .
6
7 8
5

Assembly and Operating Manual DHC
5
Fig. 9
-Apply glue to horizon tail .
Fig. 10
-Photo shows the horizon tail settled in the fuselage.
Figs. 11
-Connect the vertical tail push rod to control rod arm.
Photo shows the finished view.
Figs. 12
-Connect the horizon tail push rod to control rod arm.
Photo shows the finished view.
11
10
12
9

Assembly and Operating Manual DHC
6
Figs. 13
- Connect the wing panel push rod to the servo arm
at second hole.
Figs. 14
-Photo shows the finished view.
Figs. 15
-Reverse the procedure to the left wing. The photo
shows the finished view.
Figs. 16
-Assemble the wing panel to fuselage.
1413
15 16

Assembly and Operating Manual DHC
7
Figs. 17
-Lock the fixup presser with screw.
Figs. 18
-Photo shows the main panel assembled on the
fuselage.
Figs. 19
-Apply glue to the fixture of landing gear .
Figs. 20
-Apply glue to the fuselage.
1817
2019

Assembly and Operating Manual DHC
8
Figs. 21
-Photo shows the fixture have settled in the
fuselage.
Figs. 22
-Reverse the procedure to the left wing. The photo
shows the finished view.
Figs. 23
- Assemble the landing gear to fuselage. Photo
shows the finished view.
Figs. 24
- Assemble the back lading gear to fuselage. Photo
shows the finished view.
22
2423
21

Assembly and Operating Manual DHC
9
Figs. 25
-Connect the channels to the receiver.
Figs. 26
- Located the battery in the fuselage.
Figs. 27
-Photo shows battery leads connected to the speed
controller.
Figs. 28
-Close the battery cover,Photo shows the finished
view .
26
27 28
25

Assembly and Operating Manual DHC
10
Figs. 29
- Fixed the propeller with screw.
Figs. 30
-Photo shows the propeller settled.
Figs. 31 Balancing
- Place the canopy on the fuselage.
- Place the battery in the model of balancing; do not
connect it.
- Make the Centre of Gravity on both sides.
- Support the model at the marked C.G. and allow it
to hang freely. The model is correctly balanced
when it hangs level, ideally with the nose inclined
slightly down.
- Adjust the position of the flight battery if necessary.
- Mark the battery location in the fuselage, so that
you can be confident of replacing it in the same
position after removing it
29
31
30