Sky Angel L-39 User instructions

Assembly and Operating Manual

Assembly and Operating Manual
3
Dear customer,
Congratulations on your choice of a
factory-assembled model aircraft from the
SKYANGEL Hummingbird range and thank you
for placing your trust in us.
Very little preparation work is required to get this
model ready to fly.To operate your new model
safely it is important that you read through all of
the instructions and safety information included
with your model, before you fly it for the first time.
The illustrations in this manual show the Red
version of the model with factory applied decals.
The power system
The model is powered by a brushless outrunner
motor and ducted fan, both of which are
factory-installed on the Ready-To-Fly version.
The motor is connected to the electronic speed
controller which is factory calibrated on the
Ready-To-Fly version. All that is required is to
charge the Li-Po battery, following the safety
instructions, and connect battery to the electronic
speed controller.
The radio control system
To fly the L39 you will need a radio control system
with at least four channels. 2.4GHz radios systems
are recommended, similar to the unit included with
our deluxe version.
The servos for the ailerons and the elevators are
factory-installed.
The power for the receiver is drawn from the
electronic speed controller’s integral BEC system.
The electronic speed controller is located inside of
the fuselage, in front of the ducted fan.
To check the model’s operating systems, first set
the control surface servos to neutral, with the
transmitter sticks and trims at centre.
When you wish to fly the model, always make sure
the transmitter is in the “OFF”position. Move the
throttle stick to the “OFF”position as well. Then
connect the flight battery to the electronic speed
controller.
Switch off in the reverse order: disconnect the
battery from the electronic speed controller first,
and then switch off the transmitter.
Glued joints, suitable adhesives
Foam safe epoxy is recommended and available
from most reputable model retail shops.
Trial-fit all parts “dry”before applying glue.
Follow the recommended curing time suggested
by the glue manufacturer.Allow the glue to fully
cure (harden) to the point where the joint can be
placed under stress.
Kit contents
Fuselage, with motor, electronic speed controller
and servo
Clear canopy and cockpit
Main wing panels with ailerons and servo
Left / right tail plane panels with elevators and
vertical stabilizer
Accessories
1 x Li-Po battery, 3s 850mAh 20C
1 x 20A Brushless ESC (Electronic Speed Controller)

Assembly and Operating Manual
4
Fig. 1 Open the box and check all the parts.
Parts Illustration
Parts List
NO. Description
1 Fuselage
2 Wing Set –OneMain Wing Panel
3 Tail Set –One Horizontal Stabilizer with Elevator
4 Tail Set - One Vertical Stabilizer
5 Cockpit Canopy
6 Push Rods Set
7 Landing Skids
8 Nose Cone
9Radio Control Transmitter (we highly recommend 2.4 GHz
system)
10 850mAh 11.1 Volt 20C Li-Po Battery
11 Balance Charger
12 Landing Gear Fixed Plate set
13 Landing Gear set

Assembly and Operating Manual
5
Fig. 2 - Locate the fuselage and nose cone.
Fig. 5 - Remove any excess glue and hold in
position until glue sets. The photo shows the
finished view.
Fig. 3 - Glue the nose to the front of fuselage (glue
not included).
Fig. 6 - Connect the push rods to the elevator
servo arm and control horn.
.
Fig. 4 - Glue the horizontal stabilizers to the slots
at the rear of the fuselage (glue not included).
Fig. 7 - Photo shows the finished view after
elevator push rods are assembled.

Assembly and Operating Manual
6
Fig. 8 - Locate the fixed plate for the front wheel.
Fig. 11 - Glue the main wheel fixed plate to the slot
on one half of the main wing panel.
Fig. 9 - Glue the fixed plate into the fuselage as
shown in the photo(glue not included).
Fig. 12 - Attached the rear wheels to the fixed
plate units on each side of the main wings.
Fig. 10 - Attach the front wheel to the fixed plate
Fig. 13 - Locate the landing skid.

Assembly and Operating Manual
7
Fig. 14 - Assemble to the wing panel to the
fuselage(glue not included).
Fig. 17 - Glue the vertical stabilizer as shown in
the photo (glue not included).
Fig. 15 – Attached the white fix base as potos
shown.
Fig. 18 - Connect the electronic speed controller
and servos to the receiver. Refer to the radio
instructions for the correct channel sockets and
servo lead polarity.
Fig. 16 –Tighten the main wing with srews.
Fig. 19 - Locate the battery and canopy. Charge
the battery according to the safety instructions
before installing.

Assembly and Operating Manual
8
Fig. 20 - Photo shows battery leads connected to
the electronic speed controller.
Fig. 23 -Congratulations, you have completed
the assembly process. We hope you enjoy flying
your new model!
Fig. 21 - Insert the battery into the front of the
fuselage.
Fig. 24 - Charge the flight battery; connect the
Equalizer lead using and adapter lead matching
your charger (adapter lead not included)
Fig. 22 - The canopy is held in place by magnets
and can be lifted off.
Fig. 25 - Switch the transmitter on, and move the
throttle stick to the “Motor OFF”position. (Diagram
MODE 1 right throttle control stick)

Assembly and Operating Manual
9
Fig. 26 and 27 -Checking Ailerons and Elevators
- Check that the control surfaces respond to the appropriate
movements of the transmitter sticks. If not, swap over the
connectors at the receiver.
- Check the neutral position of the control surfaces; you may
need to screw the clevises in or out to correct any discrepancy.
- Stand behind the model.
- Check the direction of rotation of the servos:
- Move the aileron stick to the right (a), and the right aileron (a)
must rise up, the left aileron (b) fall down.
- Pull the elevator stick back towards you (c), and the
trailing edge of both elevators should rise (c).
- If either function works in the wrong way, correct it using your
transmitter’s servo reverse facility for that channel.
Fig. 28 -Checking the power system
- Hold the model securely.
- Remove any loose objects such as cloths, tools, etc from the
area in front of the model, as they could easily be sucked into
the ducted fan.
- Open the throttle (stick forward): the motor should now run,
and you should feel a strong air flow rushing out from the tail
end of the model.
- Move the throttle stick back to the “Motor OFF”position.
- Disconnect the battery from the electronicspeed controller and
then switch the transmitter off.

Assembly and Operating Manual
10
Fig. 29 -Checking the model’s balance
- Place the flight battery in its compartment, without connecting.
- Mark the Centre of Gravity (CG) on both sides of the fuselage; the position
is shown in the photo.
- Support the model at the marked points and allow it to hang freely. When
correctly balanced the airplane will remain horizontal, with the nose
slightly down.
- If necessary, adjust the position of the flight battery to achieve the correct
CG.
- Mark the battery location in the fuselage, so that you can be sure of
positioning it correctly after recharging.
- Pack scrap pieces of foam around the battery in its final position,
otherwise there is a danger of it shifting in flight and altering the model’s
balance.
- Charge the flight battery and the model is ready for flight.
Fig. 30 -Access to the ducted fan unit and electronic speed controller
- The ducted fan unit is accessible from underneath, if you need to carry out
maintenance work or repairs.
- Ensure that the wire colors match correctly.