SkyLink SkylinkHome Smart Button GB-434 User manual

Smart ButtonTM
GB-434
1. INTRODUCTION
Model GB-434
Smart ButtonTM
Garage Door Control
Congratulations on your purchase of the SkylinkHomeTM Smart ButtonTM.
The Smart ButtonTM is designed to work with SkylinkHomeTM remote such
as TC-434 series, TB-434 series, and more to operate the Garage Door
Opener. In this kit, you will find the following:
Programming
Learn additional remote controls
Smart ButtonTM GB-434 can learn up to 10 remote controls.
To learn additional remote controls, follow the
instructions below:
1. Press the learn button on the side of the GB-434.
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
3. Within 30 seconds, press the button on the remote
control you would like to program.
4. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
5. You may now operate the garage door opener
with this remote control.
Learn Button
3. OPERATION
Unplug the power cord of your garage door opener
before installation to ensure power is not connected.
WARNING Rating of the transformer:
12V DC, 100mA
Diameter of DC plug : 3.5mm
1. Open up the “Easy ClipTM” and place it underneath
the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires
are placed properly inside the channels of the
“Easy ClipTM”.
NOTE:
Ensure the ribbon wires
are not twisted but laid
flat inside the clip.
If your wall button ribbon wires
are not the AWG#22 or #24 or
the same kind as shown in the
diagram, please refer below (4)
or visit our website
www.skylinkhome.com for
more information.
2. INSTALLATION
Easy ClipTM
Ribbon Wires
Wall Button
Ribbon Wires
Press / lock
2. INSTALLATION (CONT)
Erase remote controls
To erase unwanted remote control(s)from the memory of Smart ButtonTM
GB-434, first erase all remote controls, then learn the one(s) you would
like to keep.
To erase remote control(s), follow the steps below:
1. Press and hold the learn button for approximate 10 seconds.
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. Release the learn button.
3. You have erased all the remote controls programmed to the Smart
ButtonTM GB-434.
3. Press and lock the clip by snapping it together. The included Crimper
helps you lock the “Easy ClipTM”. Close the cover and press down to
lock the cover using this Crimper until you hear a “click”.
If the Smart ButtonTM GB-434’s red LED does not flash after the Smart
ButtonTM GB-434 has been connected to the wall button’s wires
for 2 minutes, your garage door opener is probably too old.
However, the Smart ButtonTM will still work if you plug in an
adapter (purchased separately). Please contact
Skylink®to purchase the adapter.
5. If the wall button wires are hidden inside the
wall, please connect the “Easy ClipTM” to
the exposed wires attached to the
terminals of the garage door
opener.
4. If the “Easy ClipTM” cannot clip with the wires from your wall button, cut
off the “Easy ClipTM” then connect two wires from the Smart ButtonTM
to the wall button.
a) Dismount the existing wall button from the wall.
b) Connect the 2 wires from the Smart ButtonTM
GB-434 to your existing wall button. Polarity
does not matter, so simply pick one wire from
the Smart ButtonTM and connect it to one of the
screw terminals on your wall button. Connect
the 2nd wire to the other screw terminal.
c) Mount the wall button back.
Crimper
Double Sided Tape
If the red LED flashes slowly, the Smart ButtonTM GB-434
is in standby mode. When a valid remote control signal is
received, it will open / close the garage door.
Press the programmed button on the remote control
or Smart ButtonTM GB-434, it will open / close the
garage door.
6. Power up the garage door opener, the red LED on the Smart ButtonTM
GB-434 should keep flashing slowly within 2 minutes.
7. Secure the SmartButtonTM GB-434 properly with the mounting accessories.
Note: Do not cut the antenna! Straighten up the antenna to improve
signal reception.
Note:
After installation of the “Easy Clip TM ”, if you want to re-install the Smart
Button TM GB-434 to another place, please open the “Easy Clip TM ” by gently
unlocking the two buckles with a screw driver, and remove it from the
wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it.
OPEN /
CLOSE
Button
LED
LED
Antenna

7. WARRANTY
If, within one year from date of purchase, this product should become
defective (except battery), due to faulty workmanship or materials, it will
be repaired or replaced, without charge. Proof of purchase and a Return
Authorization are required.
8. CUSTOMER SERVICE
CUSTOMER SERVICE
Rm 1303, Block B, Veristrong Industrial Centre,
36 Aupuiwan Street, Fotan, N.T. Hong Kong.
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Y001
©2010 SKYLINK GROUP
5. WARNING
DO NOT let children use the garage door transmitter without adult
supervision. Otherwise, Children and others may be injured by the
garage door.
6. CE
Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 300220-2, EN301489-3, EN61058-1, EN50371.
This equipment conforms to the essential requirement of the Directive
(1999/5/EC) of the European Parliament and of the Council.
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected]
You can add up to 16 additional transmitters to
control the Smart ButtonTM GB-434. SkylinkHome®
offers different lighting control / automation
transmitters to work with your receiver. For more
information, please visit our website at
www.skylinkhome.com or contact us.
4. ADDITIONAL TRANSMITTER