Skymen A6 Pro User manual

The picture is for reference only, please refer to the actual product
Please read the instruction manual carefully before use
Please keep this instruction manual properly
Intelligent ultrasonic cleaner
A6 Pro
User Manual

1Cover 2Stainless steel tank
5Control panel
8
UV-C Light
4Power connector
7Body
3Maximum water line
6Power socket
Ultrasonic switch
UV switch
1
2 3
4
4
5
6
8
7
Application
Species Species
Optical
Office supplies
Daily necessities
Jewelry
Tableware supplies
Glasses (no UV coating)
Rulers, scissors, pens, etc.
Toothbrush, Shaver, comb, etc.
Rings, necklaces, earrings, etc.
Metal tableware, ceramic tableware,
dentures, etc
Application
Model A6 Pro 177*81*45mm
220*104*72mm
46KHz
3mins
Rated voltage
Capacity
Power
Tanks size
Product size
Working time
Frequency
12V 2A
550mL
24W
Product components and functions introduction
Product technical parameter

Touch the switch once to start the machine and enter the state of
separate cleaning for 3 minutes. During the cleaning process, there will be
a "sizzle" sound, the green light is on, And touch the switch during the
cleaning process, the machine stops working, touch it again, and the
cleaning continues.
Touch the switch once to start the machine, and enter the state of
separate ultraviolet disinfection and sterilization for 3 minutes, the blue
light is on, and touch the switch once during the cleaning process, the
machine stops working, touch it again, and the work continues.
During ultrasonic cleaning, touch the switch once, ultrasonic and UV
disinfection work at the same time. The working time of UV disinfection is
3 minutes from when UV disinfection is turned on. Ultrasonic cannot be
turned on when UV disinfection t is working alone. When working at the
same time, touch the switch once to turn off the ultrasonic and UV
disinfection, and touch the switch once to turn off only the UV disinfection.
After cleaning, pour out the water in the stainless steel inner tank, and
wipe the body and the stainless steel inner tank with a clean soft cloth.
Store in a dry, flat place.
Connect the power supply, the white light is on, and it enters the standby
state. Open the upper cover, pour clean water into the stainless steel inner
tank, and put the items to be cleaned into the water. (The parts that need to
be cleaned are fully immersed in water, But the water level cannot exceed
the maximum water level line "MAX-").
CAUTION:
When cleaning the glasses, place the lens facing up. Do not touch the
stainless steel tank directly.
It is forbidden to directly add water to the tap, which may cause electric
shock and malfunction.
The "sizzling" sound during the cleaning process is the sound of ultrasonic
vibration, which is a normal phenomenon.
After each cleaning, be sure to pour out the water in the machine, even if
the water is only used once.
In order to avoid malfunctions caused by overheating of the machine,
when the machine is continuously used for multiple times, it should not
exceed 15 minutes, and there must be a rest period in between.
Species
Wooden product
Not
Applicable
Turtle shell frame, pearls,
Opal, emerald, coral, ivory,
Emerald, stone, etc. Watch
body (including waterproof
watch), lacquerware.
Gems with soft surface
hardness
Inferior products for plating
and finishing
Glued gems
Supplies with scratches and
cracks
Concrete example
The machine will be damaged if operate ultrasonic
without water
Operating steps

Problems that need to be paid attention to when cleaning
Cleaning and Sterilization time
Please do not disassemble the product easily if you are
Non-professionals
Pearl jewelry, jade, gems with soft surface hardness;
objects with serious cracks;
Products and wood products with poor plating and
finishing are not suitable for cleaning with this product;
Whether Lacquerware and some valuables product can
be cleaned, please consult before cleaning.
TIPS
It may not be able to completely remove tartar, sallow, dark spots,
and smoking remaining etc in the dentures.
It may not be possible to clean the sedatives fixed in the dentures.
Discoloration and rusting of metals and metals cannot be removed.
When cleaning necklaces/rings with gems/diamonds glued together,
the gems/diamonds may fall off
When cleaning the metal watchband, please remove the watchband
from the main body of the watch before cleaning, only use cleaning
fluid or cleaning water. Do not put the watch (including waterproof
type) into the cleaner, it may cause the water enters inside the watch
body and the ultrasonic vibration power causes damage to the
internal parts of the watch body.
When cleaning the glasses, the lens should be placed upward, and
the cleaning time is 1-3 minutes.
When cleaning stubborn stains, the cleaning solution can be evenly
applied to the lens, and then put into the water, the cleaning effect is
better.
Since the coating technology has not yet broken through, the glasses
with the lens filming or frame coating process, please first consult the
optical shop to confirm whether it can be used for ultrasonic cleaning,
so as to avoid unnecessary losses.
Application Cleaning and Sterilization time
Glasses (no UV coating)
Rulers, scissors, pens, etc.
Toothbrush, Shaver, comb, etc.
Rings, necklaces, earrings, watch
strap etc.
Metal tableware, ceramic tableware,
dentures, etc
About 3 minutes
Note: Prolonged cleaning and disinfection may
cause damage to items, The cleaning and
disinfection process should not be too long.

When cleaning and maintaining, please disconnect the power plug
first
Wipe the surface of the machine with a damp cloth, and then wipe
off the water with a dry cloth.
Do not see water into the switch and power connection
Thank you very much for purchasing this product! The relevant
certifications of our products are complete, and all products have been
strictly tested before delivery From the date of purchase, we promises
to provide "one-year warranty, lifetime maintenance" service, but the
return freight is borne by the buyer, and the maintenance service
outside the warranty scope will be charged according to the actual
situation.
Cleaning and maintenance
Warranty notes
Cause of issue Maintenance records Maintenance time
WARRANTY CARD
Safety Precautions
In order to avoid fire, electric shock, and personal injury, please be sure
to comply with the following requirements; Or please follow the relevant
national and local electrical regulations
Ultrasonic working environment: ambient temperature requirements 0℃-50℃
Cleaning fluid requirements: It is forbidden to use liquids that are corrosive to
stainless steel and ABS plastics as cleaning fluids.The temperature of the
lotion should not exceed 60°C.
The continuous working time of the machine shall not exceed 15 minutes, and
there must be a break in between.
Requirements for placing the machine: if it will not be used for a long time, be
sure to wipe the machine clean and make sure it is placed the place is not
humid! Remember that there should be no liquid in the machine when it is
stored.
This product cannot be used as a child's toy, and children are not allowed to
use this product without supervision.

The following situations are not covered by the one-year free warranty:
1. Exceeding the warranty time; 2. All man-made damage; 3. Failure
to operate, maintain, and keep in accordance with the product
instruction manual causes damage; 4. The user disassembles the
machine for maintenance without permission; 5. Without this warranty
card or altering the warranty card without authorization; 6. The product
model on the warranty card does not match the actual product;
7. Damage caused by force majeure during use, such as floods,
earthquakes, etc.
Please complete the return and exchange content, reason, model,
purchase time, contact person, phone number,Consignee address,
and strengthen the packaging before sending back. Please ensure that
the packaging of the tank of the returned machine is complete and
clean. If the tank or the appearance is dirty, scratched, deformed and
other factors that affect the secondary sales, the return will not be
refunded; if the product is damaged due to packaging problems, the
warehouse will directly refuse the parcel. Also refuse to receive the
parcel with freight collect, thank you for your cooperation!
Certificate of conformity
Intelligent ultrasonic cleaner
A6 Pro
Product name :
Model :
Inspectors :
Test result :
Return & exchange Precautions
Skymen Cleaning Equipment Shenzhen Co., Ltd
Office：3F, A1 Block, Fuhai Technology Park Building, FuYong
Steet, baoan district, Shenzhen, Guangdong, China.
Factory：Skymen Ultrasonic, Wujiang Technology Industrial Park,
Wujiang District, Shaoguan City, Guangdong, China.
Tel：[phone] Email：[email protected]
website：www.skymen.cc
Solemnly declare
The company's products are constantly improving, and the design and specifications are subject to
change without notice. All the information in this manual has been carefully proofread and strived to
be accurate. If there are any printing errors or omissions, the company reserves the right of
interpretation. The copyright of this manual belongs to Skymen Cleaning Equipment Shenzhen Co.,
Ltd., without written authorization, it is strictly forbidden to reprint or reprint, and the company will
pursue its legal responsibility if it violates it.