Skymen A6 User manual

The picture is for reference only, please refer to the actual product
Please read the instruction manual carefully before use
Please keep this instruction manual properly
Intelligent ultrasonic cleaner
A6
User Manual

Product components and functions introduction
Application
Product technical parameter
1Cover 2Stainless steel tank
4Control panel 6Body
3Maximum water line
5Power socket
Model A6 177*81*45mm
220*104*72mm
46KHz
3mins、5mins
Rated voltage
Capacity
Power
Tanks size
Product size
Working time
Frequency
12V 2A
550mL
24W
3 mins clean
5 mins clean
1
2 3
4
5
6
Application
Species Species
Optical
Office supplies
Daily necessities
Jewelry
Tableware supplies
Glasses (no UV coating)
Rulers, scissors, pens, etc.
Toothbrush, Shaver, comb, etc.
Rings, necklaces, earrings, etc.
Metal tableware, ceramic tableware,
dentures, etc

The machine will be damaged if operate ultrasonic
without water
Operating steps
After cleaning, pour out the water in the stainless steel
inner tank, and wipe the body and the stainless steel
inner tank with a clean soft cloth. Store in a dry, flat
place.
Connect the power supply, the white light is on, and it
enters the standby state. Open the upper cover, pour
clean water into the stainless steel inner tank, and put
the items to be cleaned into the water. (The parts that
need to be cleaned are fully immersed in water,But the
water level cannot exceed the maximum water level
line "MAX-")
Touch the switch button once to start the machine
and enter 5 minutes cleaning, touch the switch button
once to start themachine and enter 3 minutes cleaning.
During the cleaning process, there will be a "sizzling"
sound, the green light is on, Touch the switch once
during the cleaning process, the machine stops working,
touch it again, the cleaning continues.
Species
Wooden product
Not
Applicable
Turtle shell frame, pearls,
Opal, emerald, coral, ivory,
Emerald, stone, etc. Watch
body (including waterproof
watch), lacquerware.
Gems with soft surface
hardness
Inferior products for plating
and finishing
Glued gems
Supplies with scratches and
cracks
Concrete example
CAUTION:
When cleaning the glasses, place the lens facing up. Do not touch the
stainless steel tank directly.
It is forbidden to directly add water to the tap, which may cause electric
shock and malfunction.
The "sizzling" sound during the cleaning process is the sound of ultrasonic
vibration, which is a normal phenomenon.
After each cleaning, be sure to pour out the water in the machine, even if
the water is only used once.
In order to avoid malfunctions caused by overheating of the machine,
when the machine is continuously used for multiple times, it should not
exceed 15 minutes, and there must be a rest period in between.

Problems that need to be paid attention to when cleaning
Cleaning time
Please do not disassemble the product easily if you are
Non-professionals
Pearl jewelry, jade, gems with soft surface hardness;
objects with serious cracks;
Products and wood products with poor plating and
finishing are not suitable for cleaning with this product;
Whether Lacquerware and some valuables product can
be cleaned, please consult before cleaning.
TIPS
It may not be able to completely remove tartar, sallow, dark spots,
and smoking remaining etc in the dentures.
It may not be possible to clean the sedatives fixed in the dentures.
Discoloration and rusting of metals and metals cannot be removed.
When cleaning necklaces/rings with gems/diamonds glued together,
the gems/diamonds may fall off
When cleaning the metal watchband, please remove the watchband
from the main body of the watch before cleaning, only use cleaning
fluid or cleaning water. Do not put the watch (including waterproof
type) into the cleaner, it may cause the water enters inside the watch
body and the ultrasonic vibration power causes damage to the
internal parts of the watch body.
When cleaning the glasses, the lens should be placed upward, and
the cleaning time is 1-3 minutes.
When cleaning stubborn stains, the cleaning solution can be evenly
applied to the lens, and then put into the water, the cleaning effect is
better.
Since the coating technology has not yet broken through, the glasses
with the lens filming or frame coating process, please first consult the
optical shop to confirm whether it can be used for ultrasonic cleaning,
so as to avoid unnecessary losses.
Application Cleaning time
Glasses (no UV coating)
Rulers, scissors, pens, etc.
Toothbrush, Shaver, comb, etc.
Rings, necklaces, earrings, etc.
Metal tableware, ceramic
tableware, dentures, etc
About 3 minutes
Note: Excessive cleaning will cause damage
to items and blades drop, especially cleaning
the outer blade for a long time.

When cleaning and maintaining, please disconnect the power plug
first
Wipe the surface of the machine with a damp cloth, and then wipe
off the water with a dry cloth.
Do not see water into the switch and power connection
Thank you very much for purchasing this product! The relevant
certifications of our products are complete, and all products have been
strictly tested before delivery From the date of purchase, we promises
to provide "one-year warranty, lifetime maintenance" service, but the
return freight is borne by the buyer, and the maintenance service
outside the warranty scope will be charged according to the actual
situation.
Cleaning and maintenance
Warranty notes
Cause of issue Maintenance records Maintenance time
WARRANTY CARD
Safety Precautions
In order to avoid fire, electric shock, and personal injury, please be sure
to comply with the following requirements; Or please follow the relevant
national and local electrical regulations
Ultrasonic working environment: ambient temperature requirements 0℃-50℃
Cleaning fluid requirements: It is forbidden to use liquids that are corrosive to
stainless steel and ABS plastics as cleaning fluids.The temperature of the
lotion should not exceed 60°C.
The continuous working time of the machine shall not exceed 15 minutes, and
there must be a break in between.
Requirements for placing the machine: if it will not be used for a long time, be
sure to wipe the machine clean and make sure it is placed the place is not
humid! Remember that there should be no liquid in the machine when it is
stored.
This product cannot be used as a child's toy, and children are not allowed to
use this product without supervision.