Skyrc T400Q User manual

Scan for
T400Q instruction manual
or download through www.skyrc.com
Thanks for purchasing SkyRC T400Q AC/DC Quattro Balance Charger/Discharger.
This charger comes with four independent circuits that can charge various chemistries
batteries (LiPo/LiFe/Lilon/LiHV/NiMH/NiCd/Pb). The charger delivers up to 100W
per port and can charge four batteries simultaneously at up to 12 amps each. It
comes ready to charge in the most compact design yet while taking up minimal
space in the pit area. And the handle design ensures the charger is convenient to
carry. Additionally, the charger also can charge AGM and Pb battery under a low
temperature in the AGM and Cold modes.
LCD Display
Scroll Through the Main Menu
Stop Any Charge Processes
Alter Values
See the Status
of Individual Cells in
Balance Charge Mode
Switch Between Port
A, B, C and D.
Output Socket
Resume or Start
Charge Processes
LED Indicator
Balance Port
AC Input
100-240V
Ventilation Slot
Carrying Handle
DC Input
11-18V
Smart
Ventilation Fan
These warnings and safety notes are particularly important. Please follow the
instructions for maximum safety; otherwise the charger and the battery can be
damaged or at worst it can cause a fire.
Never leave the charger unattended when it is connected to its power
supply. If any malfunction is found, TERMINATE THE PROCESS AT
ONCE and refer to the operation manual.
Keep the charger well away from dust, damp, rain, heat, direct sunshine
and vibration. Never drop it.
The allowable AC input voltage is 100~240V AC and DC input 11-18V.
This charger and the battery should be put on a heat-resistant,
noninflammable and nonconductive surface. Never place them on a car
seat, carpet or similar. Keep all the inflammable volatile materials away
from operating area.
Make sure you know the specifications of the battery to be charged or
discharged to ensure it meets the requirements of this charger. If the
program is set up incorrectly, the battery and charger may be damaged.
It can cause fire or explosion due to overcharging.
!
!
!
!
!
Warning and Safety Notes
AC/DC Quattro Balance Charger/Discharger
QUICK START GUIDE

Power and Battery Connection
Specification
1. Connect to the power source
2. Connect the battery
AC 100-240V Mains Power Supply: 12V DC Battery / DC Power Supply:
There are two ways to power SkyRC T400Q: DC 11-18V and AC 100-240V.
To avoid short circuit, always connect the charge leads to
the charger first, and then to the battery.
Disconnect the pack in the reverse order.
1) LiPo Battery Connection
For safety reasons, the default setting for charging Lithium (LiPo, Lilon,
LiFe and LiHV) battery is using a balance adaptor to connect the battery and
charger in Charge, Fast Charge, Balance Charge, Discharge and Storage
modes.
But if the battery comes without balance wires, please proceed with the
prompt message "No balance cable detected, push Enter to continue."
The balance wires of the battery must connect to the charger with the black
wire aligned to the negative marking. Ensure correct polarity!
2) NiMH/NiCd or Pb Battery Connection
Please scan and watch the tutorial video about how to
charge LiPo battery in balance mode.
AC Input Voltage: 100-240V
DC Input Voltage: 11-18V
LiPo/LiHV/LiFe/LiIon: 1-6S
NiMH/NiCd: 1-15S
Pb: 2-20V
Charge Wattage: 100W X 4
Charge Current: 0.1-12.0A
Balance Current: 500mA/cell
Discharge Wattage: 10W
Discharge Current: 0.1-2.0A
Weight: 1610g
Case Size: 186*103*209mm
RoHS
© 2022.07 [Version 1.0]
7504-1666-01
Manufactured by
All specications and gures are subject to change without notice.
SKYRC TECHNOLOGY CO., LTD.