Sloan OPTIMA I.Q. EAF-150 Series User manual

ADA Compliant
EAF-100/150 I.I. — Rev. 1 (07/04)
Code No. 0816542
INSTALLATION INSTRUCTIONS
ELECTRONIC
SENSOR OPERATED
LAVATORY FAUCETS
EAF-1150
Series
Battery Powered
Sensor Operated
Lavatory Faucets
EAF-1100
Series
Plug-in Transformer Powered
Sensor Operated
Lavatory Faucets
Sloan’s Optima EAF-100/150 Series electronic hand washing
faucets operate by means of a dual infrared sensor and microprocessor
based logic. The modular design of the faucet simplifies installation and
maintenance by incorporating all of the operating components above the
sink within the die-cast metal spout.
ISM models feature an integral temperature control lever to allow the
user to adjust water temperature. The faucet can also be adjusted and set
to a fixed mixer setting. Faucets ordered without the ISM variation must
be connected to a single, pre-tempered water supply.
The faucet is also available with the - Click feature. This feature
allows the user to set faucet modes, including “continuous run” and
“temporary off” simply by pressing a button on the spout. This feature is
recommended only in installations where users have a regular familiarity
with the faucet (i.e., executive and non-public rest rooms). Models
furnished with the - Click feature are also available with a Drain Pop
Up.
Optima EAF-150 series faucets include a 6 VDC lithium battery.
Battery life is approximately three (3) years. EAF-100 series faucets are
hard wired and include a plug-in transformer.
The following instructions will serve as a guide when installing the Sloan
Optima EAF-100/150 series sensor operated faucets. As always, good
safety practices and care are recommended when installing your new
faucet. If further assistance is required, contact your nearest Sloan
Representative office or the Sloan Installation Engineering Department at
1-888-SLOAN-14 (1-888-756-2614).
LIMITED WARRANTY
Sloan Valve Company warrants its Optima EAF-100/150 Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material
or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and
serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which
prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will
be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the battery.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
TThhee
OOppttiimmaa ffaauucceett
——
BBrriinnggiinngg iinntteelllliiggeennccee ttoo wwaatteerr

2
ROUGH-IN — Figure 1
MODELS EAF-100/150
2.2 gpm (8.3 Lpm) Max. Flow Aerator
Faucets with Single Line Water Supply
MODELS EAF-100/150-ISM
MODELS EAF-100/150-ISM-DPU-IC
2.2 gpm (8.3 Lpm) Max. Flow Aerator
Faucets with Hot and Cold Water Supply
FAUCET SPOUT DIMENSIONS AND POP UP DETAILS
SPOUT
HOT
SUPPLY
COLD
SUPPLY
O-RING
GASKET
RETAINER
NUT
MIXING VALVE
1-3/16” (30 mm)
MIN. DIA. HOLE
REQUIRED
1-1/2” (38 mm)
MAX. DECK
THICKNESS
SPOUT
TEMPERED
SUPPLY
O-RING
GASKET
RETAINER
NUT
1-3/16” (30 mm)
MIN. DIA. HOLE
REQUIRED
1-1/2” (38 mm)
MAX. DECK
THICKNESS
5-9/16”
(142 mm)
6-7/8”
(175 mm)
24º
2-3/8
(60 mm)
2-3/4
(70 mm)
POP UP —
MODELS EAF-100/150-ISM-DPU-IC ONLY
Figure 1A Figure 1B
Figure 1C
FAUCET VARIATIONS
-ISM Integral Spout Mixer
-IC -Click Feature
-DPU Drain Pop Up
-P Plug-in Transformer (EAF-100 Series only)
PRIOR TO INSTALLATION
Prior to installing the Sloan Optima EAF-100/150 Series Faucet, install
the items listed below. Also, refer to Figures 1A thru 1C.
• Lavatory/sink
• Drain line
• Hot and cold water supply lines or pre-tempered water supply line
IMPORTANT:
•ALL PLUMBING IS TO BE INSTALLED IN ACCORDANCE WITH
APPLICABLE CODES AND REGULATIONS.
•FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
Trim Plates
When the EAF Faucet is installed on a sink that has three (3) hole
punchings, a Trim Plate should be used. Trim
Plates must be specified
and
ordered separately.
ETF-607-A Trim Plate for 4” (102 mm) Center-set Sink
ETF-608-A Trim Plate for 8” (203 mm) Center-set Sink
TOOLS REQUIRED FOR INSTALLATION
• 13 mm open end wrench for male end of flex hose
• 13 mm open end wrench or nut driver for Faucet retainer nut
• 3/4” open end wrench for female end of flex hose
If connection to separate hot and
cold water supplies is desired, then a
Bak-Chek®(not supplied) must be
used prior to connecting to the
Faucet.
13” (330 mm)
LONG FLEX HOSES
13” (330 mm)
LONG FLEX HOSE
2-3/8
(60 mm)
When the EAF Faucet is installed on a sink that has three (3) hole
punchings, a trim plate should be used.
Trim
Plates must be specified and ordered separately:
ETF-6607-AA
Trim Plate for 4” (102 mm) Center-set Sink
ETF-6608-AA
Trim Plate for 8” (203 mm) Center-set Sink
When
installing the
Faucet on a three (3) hole sink, make sure that the
center
hole is large enough to
accommodate the Faucet shank.
A
1-33/16" (30 mm) minimum diameter hole is required.
NOTE:
A 1-77/32” (31 mm) Diameter hole is required if the deck is
greater
than 1/2” (13 mm)
thick.

Step 2
Install Faucet with O-ring
into the center hole in
deck or lavatory —
1-33/16"
(30 mm) min.
hole
required.
Note: If installing the
Faucet on a three (3)
hole sink, a Trim Plate
should be installed at
this time.
FAUCET
CENTER HOLE IN
DECK OR LAVATORY
Step 1
Remove all
Mounting Hardware:
• Nut
• Faucet Retainer
• Gasket
Do Not remove the
O-ring from base of
Faucet.
FAUCET INSTALLATION
Step 3
Slide Gasket over Flex
Hose(s).
Secure Faucet to deck
or lavatory with Faucet
Retainer and Nut.
GASKET
FAUCET RETAINER
FAUCET
FLEX HOSE
NUT
MODELS
POWERED BY
PLUG-IIN
TRANSFORMER
ONLY
DO
NOT pull or crimp AC
Power Line.
GASKET
FAUCET RETAINER
NUT
O-RING —
DO NOT REMOVE
O-RING
O-RING
Step 4
IMPORTANT:
Flush dirt, debris, and sediment
from Supply Line(s) before
Connecting Flex Hoses.
Install Strainer and Flex Hose onto
Supply Stop.
Tighten the Flex Hose (with
Strainer in place) securely to the
Supply. SUPPLY LINE/STOP
STRAINER
FLEX HOSE
Step 5
Open Supply Stops.
Step 6
Remove sticker
from sensor.
For EAF 100
Models, Plug
Transformer
into receptacle.
Step 7
Press button one (1)
time, then immediately
step away.
Faucet will run for four (4)
seconds and the range
will automatically adjust
to it’s environment.
Wait ten (10) seconds
after water shuts off
before using Faucet.
If Faucet does not
function, refer to the
Troubleshooting section
of this instruction
manual.
IC
MODELS
STANDARD
MODELS
Transformer must be within 24” of Faucet.
Step 8
Activate Faucet and
check for leaks.
Step 9 —
ISM Models Only
SET
TEMPERATURE
Adjust Lever.
3

TO
FIX TEMPERATURE
Set to desired position. Remove Handle. Plug hole with Cap.
4
OPERATION
As the user’s hands enter the
beam’s effective range, the
beam is reflected back into the
sensor receiver and activates
the solenoid valve allowing
water to flow from the Faucet.
Water will flow until the hands
are removed or until the Faucet
reaches its automatic time out
limit setting.
CARE AND CLEANING OF CHROME AND
SPECIAL FINISHES
DO NOT use abrasive or chemical
cleaners (including chlorine bleach)
to clean Faucets that may dull the
luster and attack the chrome or
special decorative finishes. Use
ONLY mild soap and water, then
wipe dry with clean cloth or towel.
While cleaning the bathroom tile,
protect the Faucet from any
splattering of cleaner. Acids and
cleaning fluids will discolor or
remove chrome plating.
MANUAL RANGE ADJUSTMENT
Note:
use Manual Range Adjustment only when desired
range
cannot be obtained with Auto Range
Adjustment in
Step
7.
Push button two (2) times
(double click).
Push again for five (5)
seconds until LED flashes
four (4) times.
Then release button and
wait five (5) seconds.
-Click FEATURE
The -Click feature is a button on
the underside of the Faucet spout
that allows the user to place the
Faucet into the following function
modes: Continuous Run, Temporary
Off, Permanent Off, optional Twenty-
Four Hour Sentinel Rinse and Auto Set Range Adjustment.
-Click SETTINGS
Continuous Run
Water flows from 1 - 20 minutes constantly — for easy
filling of sink, pail or for hygienic handwashing. Default
setting is two (2) minute run time.
Temporary OFF
Water flow is deactivated up to two (2) minutes — for
convenient cleaning of sink and faucet.
Permanent OFF
The faucet is totally deactivated for safety and energy
saving reasons during long absence.
Twenty-Four Hour Sentinel Rinse
Sentinel Rinse occurs every twenty-four (24) hours from
last use to keep fixture fresh during periods of nonuse.
Auto Set Range Adjustment
All Faucets feature the Auto Set function.
The detection area is automatically adapted to the sink
where the Faucet is installed and this occurs upon initial
power up. Thus reflection is prevented and a maximum of
user convenience provided.
Push and hold button in as
Faucet continuously cycles
through the following five (5)
range settings.
One
(1) flash = longest range
Two
(2) flashes = long range
Three
(3) flashes = medium range
Four
(4) flashes = short range
Five
(5) flashes = shortest range
Release button at desired
setting. Then water will flow for
four (4) seconds signaling
confirmation of setting. Wait an
additional ten (10) seconds
before using Faucet.
Function Press Button LED Signal
Continuous Run — 2 minute
default setting (adjustable from
1 - 20 minutes)
1 time for 2 seconds
or consult Factory 5 short flashes
RESET: 1 time
Temporary Off 2 times (double click) 5 short flashes followed by
periodic flashing
RESET: 1 time or will reset
automatically after 2 minutes
Permanent Off Consult Factory Periodic flashing and then 2
long flashes
RESET: 1 time
24 Hour Sentinel Rinse 1 time for 24 seconds 2 short flashes
RESET: 1 time for 24 seconds 5 short flashes
Auto Set Range Adjustment 2 times (double click) and then
1 time for 5 seconds
4 short flashes —wait for 4
second water flow
ADDITIONAL FEATURES

5
Step 1
Close Supply Stop(s).
BATTERY REPLACEMENT
Replace battery when red LED indicator flashes each time
Faucet is in use or when Faucet stops functioning.
Step 6
Open Supply Stops.
Step 2
Loosen Screw with hex
wrench.
Remove Throat Plate.
Disconnect electrical
lead at connector if
required.
Step 3
Remove Battery Cover
using a No. 1 Phillips
head screwdriver.
Remove old Battery.
Dispose of properly.
Step 5
Insert a new 6 Volt Type 2CR5
Lithium Battery. The red LED will
flash for one (1) minute.
Reinstall Battery Cover.
Reconnect electrical lead at
connector if previously
disconnected. Reinstall Throat
Plate.
If LED doesn't flash or if it just
lights up, remove the Battery.
Wait three (3) minutes, then reinsert the Battery.
If water flows continuously after inserting the new Battery
and opening the Supply Stops, remove the Battery. Wait
three (3) minutes, then reinsert the Battery.
3 min
Step 4
Wait three (3) minutes before
inserting new battery.
TROUBLESHOOTING GUIDE
11..PPrroobblleemm::FFaauucceett
ddooeess nnoott ffuunnccttiioonn..
Cause: Adhesive packaging label affixed over sensor eye.
Solution: Remove adhesive label from sensor eye.
Cause: "Permanent Off" activated.
Solution: Press button on Faucet throat one time.
22..PPrroobblleemm::FFaauucceett
ddeelliivveerrss wwaatteerr iinn aann uunnccoonnt
trroolllleedd
mmaannnneerr..
Cause: Faucet is defective.
Solution: Contact the Sloan Valve Company Installation Engineering
Department at 1-888-SLOAN-14 (1-888-756-2614).
33..PPrroobblleemm::FFaauucceett
ddooeess nnoott ddeelliivveerr aannyy wwaatteerr wwhheenn SSeennssoorr iiss aacct
tiivvaatteedd..
Indicator: Solenoid
valve produces an audible “CLICK.”
Cause: Water supply stop(s) closed.
Solution: Open water supply stop(s).
Cause: Water supply stop strainer(s) clogged.
Solution: Clean water supply stop strainer(s).
Indicator: Solenoid
valve DOES NOT produce an audible “CLICK.”
Cause: Battery low (EAF-150 Models).
Solution: Replace battery (refer to Battery Replacement on this page).
Cause: Power failure (EAF-100 Models).
Solution: Check power supply.
44..PPrroobblleemm::FFaauucceett
ddeelliivveerrss oonnllyy aa ssllooww ffllooww oorr ddrriibbbbllee wwhheenn SSeennssoorr iiss
aaccttiivvaat
teedd..
Cause: Water supply stop(s) are partially closed.
Solution: Completely open water supply stop(s).
Cause: Water supply stop strainer(s) clogged.
Solution: Remove, clean, and reinstall water supply stop strainer(s).
Replace strainer(s) if required.
Cause: Aerator is clogged.
Solution: Remove, clean, and reinstall Aerator. Replace Aerator if
required.
Cause: Valve is defective.
Solution: Contact the Sloan Valve Company Installation Engineering
Department at 1-888-SLOAN-14 (1-888-756-2614).
55..PPrroobblleemm::FFaauucceett
ddooeess nnoott ssttoopp ddeelliivveerriinngg wwaatteerr oorr ccoonnttiinnuueess ttoo ddrri
ipp
aafftteerr
uusseerr iiss nnoo lloonnggeerr ddeetteecctteedd..
Cause: Valve is defective.
Solution: Contact the Sloan Valve Company Installation Engineering
Department at 1-888-SLOAN-14 (1-888-756-2614).
66..PPrroobblleemm::LLEEDD
iinnddiiccaattoorr bblliinnkkss wwhheenn FFaauucceett
iiss iinn uussee..
Cause: Battery low.
Solution: Replace battery (refer to Battery Replacement on this page).
77..PPrroobblleemm::-
CClliicckkddooeessnn''tt ffuunnccttiioonn ((-IICC mmooddeellss oonnllyy))
Cause: Button is defective.
Solution: Contact the Sloan Valve Company Installation Engineering
Department at 1-888-SLOAN-14 (1-888-756-2614).
88..PPrroobblleemm::TThhee
wwa
atteerr
tteemmppeerraattuurree iiss ttoooo hhoott oorr ttoooo ccoolldd oonn aa FFaauucceett
ccoonnnneecctteedd
ttoo hhoott aanndd c
coolldd
ssuuppppllyy lliinneess..
CAUSE: Supply Stops are not adjusted properly.
SOLUTION: Adjust Supply Stops.
CAUSE: For models with integral mixing valve — Mixing valve is set
improperly for the water temperature desired.
SOLUTION: Rotate mixing valve handle clockwise to decrease water
temperature or counterclockwise to increase water
temperature.
If
further assistance is required, please contact the Sloan Valve
Company
Installation Engineering
Department at 1-8888-SSLOAN-114
(1-8888-7756-22614).

Item No. Part No. Description
1A EAF-10 2.2 gpm (8.3 Lpm) Aerator Spray Head
1B EAF-12 0.5 gpm (1.9 Lpm) Spray Head
2A EAF-3-A Throat Plate Assembly (Battery Models)
2B EAF-6-A Throat Plate Assembly
(Plug-in Transformer Models)
2C EAF-4-A Throat Plate Assembly with i.q. - Click
(Battery Model)
2D EAF-7-A Throat Plate Assembly with i.q. - Click
(Plug-in Transformer Model)
3 EAF-1000 Battery Replacement Kit
Item No. Part No. Description
4 EAF-1 Faucet Mounting Kit
5 EAF-9 Strainer (Filter)
6A EAF-1001 Mixer Handle Assembly and Cartridge
6B EAF-1002 Handle Repair Kit
7 EAF-11 Transformer
8 EAF-1008 13” (330 mm) Flexible Supply Hose
9 ETF-607-A Trim Plate for 4” Center-set Sink
10 ETF-608-A Trim Plate for 8” Center-set Sink
6A
Air Delights, Inc. • 9974 SW Arctic Dr. • Beaverton, Oregon 97005
Phone: [phone] or 1-503-352-1201 • Fax: [phone]
www.airdelights.com
Printed in the U.S.A. 07-04
Copyright © 2004 SLOAN VALVE COMPANY
3
710
PARTS LIST
4
The information contained in this document is subject to change without notice.
1A
1B
2
6B
5
9
8