Sloan 0344067 Use and care manual

Repair Parts and Maintenance Guide
The information contained in this document is subject to change without notice.
Sensor Urinal Flush Valve (Hardwired/Battery)
Item Part Description
No. No.
1 0344056
2 0344077 ELG SOLENOID VALVE
B
7
2
5
6
4
3
9
10
ELG WALL BOX W/ INSERTS
30344074 ELG FLOW REGULATOR
40344061 ELG OUTLET PORT G 1/2
50365325 SLIP RING SOLENOID
60365318 END CAP SOLENOID
70344063 ELG MUD GUARD
8
0344058 ELG INLET VALVE ASSLY G/12
9
9103496 SCREW THREAD CUTTING ST4.2 x 13
8
10
0340112 GBL112 #8-32 X 2" TRUSS HEAD PHILLPS HD
13
12
1111 14
15
11 0344066
12 SEE TABLE
ELG CP TRIM PLATE W/ SLOAN LOGO
13 03440001 SCREW M3-0.5x8 MM 18-8 STL
14 0344073 ELG SPACER 5MM
15 0344070 ELG PLATE W/ INSERT
16 0340111 GBL111 #8-32 x .75 LP SOCKET HEAD SCREW
17
9103681 ELG 79 BATTERY PACKAGE
18
0344076 SCREW KIT
ELG SENSOR ASM
17
18
19
9103279 EBV9 BATTERY "AA" SIZE (4 PACK)
19
A
1
16
1

Repair Parts and Maintenance Guide
The information contained in this document is subject to change without notice.
Code No. Description
0344067 ELG SENSOR ASM 0.5 LPF
ELG SENSOR ASM SELECTION GUIDE
$&7,9$7,21$66(0%/<5(3$,5.,7
3,6721$66(0%/<5(3$,5.,7
1. BATTERY REPLACEMENT
-
-
+
+
+
-
When required, replace batteries with four (4) Alkaline AA-Size Batteries.
NOTE: WATER DOES NOT HAVE TO BE TURNED OFF TO REPLACE BATTERIES. USE ALKALINE BATTERIES FOR PROPER UNIT
OPERATION.
A. Loosen Set Screw at bottom of Wall Plate & Remove Wall Plate
B. Disconnect Battery Pack from Sensor Assembly.
C. Remove battery box from inside the Wall Box
D. Remove the battery box cover by loosening screw using a Philips head screwdriver.
E. Replace the batteries with 4 new AA Alkaline batteries as shown.
F. Reinstall the Battery cover and using a screwdriver tighten the screw until the battery cover is tightly secure.
G. Insert the Battery Compartment into the Battery Compartment Slot of the Wall Box.
H. Connect the Battery Pack to the connector located on the Sensor Assembly
I. Install Wall Plate and secure with Set Screw.
2
0344080 ELG SENSOR ASM 1 LPF
0344081 ELG SENSOR ASM 1.5 LPF
2.FILTER CLEANING AND REPLACEMENT
A. Loosen Set Screw at bottom of Wall Plate & Remove Wall Plate
B. Turn off water and activate Solenoid Valve to release water
pressure.
C. Disconnect Battery Pack and Solenoid Coil from Sensor .
D. Unscrew Inlet and Outlet Coupling from Solenoid Valve and
remove Solenoid Valve from Wall Box.
E. Remove Filter Assembly and rinse out or replace with new Filter
Assembly.
F. Reinstall Filter Assembly into Valve Body.
G. Make sure Outlet Seal is installed in outlet end of Valve Body.
H. Reinstall Solenoid Valve into Wall Box. Make sure arrow on Valve
Body faces direction of water flow.
I. Reconnect all Couplings and Electrical Connections.
J. Install Wall Plate and secure with Set Screw.
Sensor Urinal Flush Valve (Hardwired/Battery)

Repair Parts and Maintenance Guide
The information contained in this document is subject to change without notice. 3
3.OPERATION
When the user steps away
(after a minimum of 8 seconds), the flush valve automatically activates.
4.CARE AND CLEANING OF CHROME AND SPECIAL FINISHES
DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Wall Plate Cover that may dull the
luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with
clean cloth or towel.
While cleaning the bathroom tile, protect the Wall Plate Cover from any splattering of cleaner. Acids and cleaning
fluids will discolor or remove chrome plating.
5.TROUBLESHOOTING GUIDE
1. Valve does not function.
A. No power to sensor:
For battery powered model — Make sure that four (4) new AA-size Alkaline batteries are properly installed in Battery
Compartment. Refer to Battery Replacement instructions for battery orientation. Make sure that Battery Compartment
Plug is connected properly into back of Sensor.
For Transformer Powered Model — Make certain that main power is on. Check Transformer, leads and connections.
Repair or replace as necessary.
B. ELG Sensor asm, Sensor not operating. Replace Sensor Assembly.
C. Main Valve or Ball Valve is Closed. Open Main Valve and adjust the Ball Valve to meet the flow rate required for the
proper cleansing of the urinal.
2. Valve delivers only a slow flow or dribble when Sensor is activated.
A. Ball Valve not open enough. Adjust the Ball Valve to meet the flow rate required for the proper cleansing of the urinal.
B. Solenoid Filter is clogged. Replace Filter .
C. Water pressure is too low. Water pressure should be 0.7 to 5.5 Bar.
3. Valve does not stop delivering water or continues to drip after user is no longer detected (automatic shut-off fails even
when batteries are removed or Power is disconnected from the electric supply).
A. Solenoid Valve seat is dirty. Remove, clean, and reinsert Solenoid Filter. Activate valve several times to flush out dirt.
B. Solenoid Valve is dirty. Backflush by reversing water flow
(opposite to the direction shown by the arrow on the side of the Solenoid Valve) through the Solenoid Valve. Reconnect
the fittings in the correct orientation. Activate valve.
C. Solenoid Valve Assembly is defective. Replace with Solenoid Valve Assembly.
4. Water Splashes from Fixture.
A. Supply volume is excessive. Adjust the Ball Valve to meet the flow rate required for the proper cleansing of the urinal.
Sensor Urinal Flush Valve (Hardwired/Battery)