SmartRG SR350n User manual

/ GATEWAY USER MANUAL
For all Broadcom Chipset-based models including:
ADSL 3xx series: SR300n, SR350n, SR360n
VDSL 5xx series: SR500n, SR505n, SR510n, SR550n
Release 3.3
January, 2015

Table of Contents
Table of Contents 1
Introduction 3
Disclaimer 3
Federal Communications Commission (FCC) Inter
ference Statement 3
FCC Caution 3
IMPORTANT NOTE: FCC Radiation Exposure
Statement 3
Safety Warnings 4
Welcome! 5
Purpose & Scope 5
Intended Audience 5
Getting Assistance 5
Getting Familiar With Your Gateway 6
LED Status Indicators: 6
Connections: 7
DSL 7
WAN 7
LAN 8
USB 8
POWER 8
External Buttons: 8
WPS Button 8
WLAN Button 9
Reset Button 9
Logging in to Your SmartRG Gateway's UI 9
Device Info 11
Summary 11
Wan Info 11
Statistics 12
LAN 12
WAN Service 13
xTM 14
xDSL 15
Route 18
ARP 18
DHCP 19
Advanced Setup 20
Layer2 Interface 20
ATM Interface 20
PTM Interface 22
ETH Interface 24
WAN Service 24
PPP over Ethernet 24
IP Over Ethernet 31
Ethernet Config 36
Ethernet Port Configuration 36
Model-specific variants: 36
LAN 37
Local Area Network (LAN) Setup 37
NAT 39
Virtual Servers (Port Forward) 39
Port Triggering 41
DMZ Host 42
Security 43
IP Filtering - Outgoing 43
IP Filtering - Incoming 45
MAC Filtering 46
Parental Control 47
Time Restriction 48
URL Filter 48
Quality Of Service 49
QoS Config 49
QoS Queue Config 50
QoS Classification 52
QoS Port Shaping 54
Routing 55
Default Gateway 55
Static Route 56
Policy Routing 56
RIP (Routing Information Protocol) 57
DNS 58
DNS Server 58
Dynamic DNS 60
Static DNS 60
DSL 61
Advanced settings for the DSL interface. 61
DSL Bonding 64
UPnP 65
DNS Proxy 66
Interface Grouping 67
IP Tunnel 68
IPv6inIPv4 68
IPv4inIPv6 69
IPSec 70
Certificate 72
Local 72
Trusted CA 74
Multicast 75
Basic 77
Security 79
Manual Setup - Network Authentication: Open and
Shared 81
Manual Setup - Network Authentication: 802.1X 82
Manual Setup - Network Authentication: WPA 83
Manual Setup - Network Authentication: WPA-PSK 83
Manual Setup - Network Authentication: WPA2 84
Manual Setup - Network Authentication: WPA2-PSK 85
Manual Setup - Network Authentication: Mixed
WPA2-WPA 86
Manual Setup 87
Network Authentication: Mixed WPA2/WPA-PSK 87
MAC Filter 88
Wireless Bridge 89
Advanced 90
Station Info 93
Diagnostics 93
SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 1

Diagnostics 94
Fault Management 94
Management Settings 95
Backup 95
Update 96
Restore Default 97
System Log 98
Security Log 99
Management Server 100
TR-069 Client 100
STUN Config 103
Internet Time 104
Access Control 105
Services 105
Passwords 106
Update Software 107
Reboot 108
Appendix A: Advanced Features Overview 109
Connect-and-Surf (Automatic Broadband Con
nection Configuration) 109
Activation (Automatic ACS Connection Con
figuration) 109
TR-069 Remote Management: Automated
Configuration Server Support 109
Appendix B: Feature Comparison Matrix 111
Revision History 112
SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 2

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 3
Introduction
Copyright © 2014 by SmartRG, Inc.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any
language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise,
without the prior written permission of SmartRG, Inc.
Published by SmartRG, Inc. All rights reserved.
Disclaimer
SmartRG does not assume any liability arising out of the application or use of any products, or software described herein. Either does it convey
any license under its patent rights nor patent rights of others. SmartRG further reserves the right to make changes to any products described
herein without notice. This publication is subject to change without notice.
Any trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners.
Federal Communications Commission (FCC) Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
lThis device may not cause harmful interference.
lThis device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numrique de la classe B est conforme Ã la norme NMB-003 du Canada.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed an
operated with a minimum distance of 20cm between the radiator and your body.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 4
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
SmartRG Inc declares that the WR100 is limited to operations on Channels 1 through 11, from 2400 to 2483.5 MHz by specified firmware
controlled in the USA.
Safety Warnings
For your safety, be sure to read and follow all warning notices and instructions.
lTo reduce the risk of fire, use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord.
lDo NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qual
ified service personnel can service the device. Please contact your vendor for further information.
lUse ONLY the dedicated power supply for your device. Connect the power cord or power adaptor to the correct supply voltage (110V AC
in North America or 230V AC in Europe).
lDo NOT use the device if the power supply is damaged as it might cause electrocution.
lIf the power supply is damaged, remove it from the power outlet.
lDo NOT attempt to repair the power supply. Contact your local vendor to order a new power supply.
lPlace connecting cables carefully so that no one will step on them or stumble over them. Do NOT allow anything to rest on the power
cord and do NOT locate the product where anyone can walk on the power cord.
lIf you wall mount your device, make sure that no electrical, gas, or water pipes will be damaged.
lDo NOT install nor use your device during a thunderstorm. There may be a remote risk of electric shock from lightning.
lDo NOT expose your device to dampness, dust, or corrosive liquids.
lDo NOT use this product near water, for example, in a wet basement or near a swimming pool.
lMake sure to connect the cables to the correct ports.
lDo NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.
lDo NOT store things on the device.
lConnect ONLY suitable accessories to the device.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 5
Welcome!
Thank you for purchasing this SmartRG product.
SmartRG proudly brings you the best, most innovative broadband gateways available. SmartRG enables service providers to monitor, manage,
and monetize the connected home through the design and production of reliable and highly interoperable hardware and software solutions.
As an early innovator in TR-069 remote management technology, SmartRG offers the finest in managed broadband and home networking
solutions. Our products leverage various broadband access technologies and are outfitted with highly customizable software, meeting diverse
service provider requirements. Based in the USA, SmartRG provides local, proactive software development and customer support. In the rapidly
evolving broadband market, SmartRG helps service providers keep their businesses on the cutting edge through its laser-focused product line,
leveraging the very latest in broadband access and home networking technologies. SmartRG solutions enable service providers to improve their
bottom line by reducing service costs and increasing customer satisfaction.
Learn more at www.SmartRG.com.
Purpose & Scope
The purpose and scope of this document is to provide the customers of SmartRG with installation, configuration and monitoring information for
all CPE platforms.
Intended Audience
The information in this document is intended for Network Architects, NOC Administrators, Field Service Technicians and other networking
professionals responsible for deploying and managing broadband access networks. The reader of this manual is assumed to have a basic
understanding of desktop computer operating systems, networking concepts and telecommunications.
Getting Assistance
Subscribers: If you require help with this product, please contact your service provider.
Service providers: if you require help with this product, please open a support request.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 6
Getting Familiar With Your Gateway
This section contains a quick description of the Gateway's lights, ports, and buttons. SmartRG produces several models that vary slightly in
capabilities (See Appendix B for details) but the basic scheme of lights, ports and buttons represented in this section exist on each model.
LED Status Indicators:
Your SmartRG gateway has several indicator lights (LEDs) on its front panel. The number of DSL ports or USB ports may vary from model to
model but generally, these indicators are available on all models:

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 7
Connections:
Below is a generic representation of a SmartRG gateway, however your specific model may have greater or fewer ports and controls across the
back of the unit. Refer to the Quick Start Guide enclosed with your gateway for specifics regarding installation of your particular model.
The ports depicted in this example are described as follows:
DSL
The grey, RJ12 port labeled DSL is specifically intended for connection to an internet provider via a DSL (Digital Subscriber Line) service. The
center pair carries the first DSL line. For models like the SR550n equipped with two DLS ports and bonded DSL capability, the outer pair carries the
second line.
WAN
A stand-alone RJ45 port labeled WAN enables your SmartRG gateway to be hard-wired to another network device with a RJ45/Ethernet output
such as a cable, fiber, or DSL modem.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 8
For models with a stand-alone, RJ45, WAN port and a DSL port, the WAN port can be re-purposed to function as an additional LAN port when your
internet connection is via DSL.
See the ETH Interface section of this manual for further instructions to enable this SmartPortTM feature.
LAN
The set of four, RJ45 ports across the back of your gateway labeled LAN1, LAN2, LAN3, LAN4 are the means to connect client devices such as
computers and printers to your gateway.
On some models, one of these four ports may be labeled as WAN indicating SmartPortTM support. SmartPortTM enables a LAN port to be re-
purposed to function as an Ethernet WAN port (describe above). When this port is serving as a LAN port, the corresponding LED on the face of the
unit is labeled, "WAN" .
See the ETH Interface section of this manual for further instructions to enable this SmartPortTM feature.
USB
USB ports on SmartRG products currently provide +5 DC volts. Future firmware updates will enable data transfer via USB.
POWER
Use only the power supply included with your gateway. Intended for indoor use only.
External Buttons:
Smart RG gateways provide pushbutton controls on the exterior for critical features. These buttons give you a convenient means to, trigger WPS
mode, toggle the WiFi radio on and off or reset the gateway.
The following describes specifics for each of these controls.
WPS Button
Wi-Fi Protected Setup™ (WPS) is standard means for secure connection between your gateway and various wireless client devices. It is designed
to simplify the pairing process between devices.
If you have client devices that support WPS, use this to automatically configure wireless security for your network. WPS configures one client
device at a time. Reference the Quick Start Guide included with your gateway for specific instructions. Also see the Wireless chapter of this
manual.
Repeat the steps as necessary for each additional WPS compliant device you wish to connect.
The location of the WPS button varies by model.
lOn models SR550n, SR510n, and SR552n, the button is located on the left side of the unit.
lSR360n, locate the WPS button on the top of the unit.
lFor the SR350n and SR500n models, an exterior button is not present however WPS is supported via the on-board software.
Reference the Quick Start Guide included with your gateway for specific instructions.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 9
WLAN Button
The button labeled WiFi or WLAN (depending on model) toggles the WiFi radio on and off. Refer to the WLAN LED indicator to determine the
current state of the WiFi radio.
The location of the WLAN button varies by model.
lOn models SR360n, SR550n, SR510n, SR552n and SR630n, the button is located on the left side of the unit.
lFor the SR350n and SR500n models, an exterior button is not present however WPS is supported via the on-board software. Reference
the Quick Start Guide included with your gateway for specific instructions.
Reset Button
The Reset button is a small hole in the gateway's enclosure with the actual button mounted behind the surface. This style of pushbutton prevents
the gateway from being inadvertently reset during handling. Reset must be actuated with a paper clip or similar implement.
This pin-hole sized reset button has three functions. The duration for which the button is held dictates which function is carried out.
lBrief, momentary contact performs a modem reset that is equivalent to the Reboot function in the gateway's software UI.
lA 5 second hold on the Reset button performs the software UI equivalent to Restore Default.
lHolding reset for 10-15 seconds - the POWER LED goes red and unit enters CFE mode. A state associated with performing firmware
updates via Internet browser.
The location of the Reset button varies by model.
lOn models SR500n, SR505n, SR510n, SR550n, SR552n and SR630n, the button is located on the rear of the unit.
lFor the SR350n, locate the Reset button on the bottom of the unit.
lFor the SR360n, locate the Reset button on the left side of the unit.
Logging in to Your SmartRG Gateway's UI
To manually configure the SmartRG Gateway, access the gateway's embedded web UI:
1. Attach your computer's RJ45 connection to any of the SmartRG gateway's LAN ports (1-4).
2. Configure your computer's IP interface to acquire an IP address using DHCP. (See the IMPORTANT note below for instructions on logging in to a SmartRG gateway configured
for "bridge mode" operation.)
3. Open a browser and enter the gateway's default address http://192.168.1.1in the address bar.
4. Click the Manage Gateway (Advanced) link in the upper right.
5. Enter the default username and password: admin/admin and click Login to display the Device Info page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 10
NOTE: The gateway's UI can be accessed via the WAN connection by entering the WAN IP address in your browser's address bar and entering the
default username and password: support/support. WAN HTTP access control MUST be enabled to access the gateway's UI via the WAN
connection. Reference section on Management Access Controlfor details.
If your SmartRG gateway is configured for "bridge mode" (modem) operation, your PC will NOT be able to acquire an address via CPE's DHCP.
Instead, manually configure your PC's interface with an IP address on the default network (e.g. 192.168.1.100).
The balance of this guide is dedicated to a sequential walk-through of the user interface of your gateway. Here you will find a visual reference of
each screen along with a Description for each of the parameters displayed. Where applicable, a range of valid values is outlined along with an
overview narrative of each screen.
For in depth "how-to" information for specific scenarios, please take advantage of the knowledge base found at our support web site. Access to
this site is restricted to SmartRG customers and partners. Do not attempt to share links to this site with your subscribers.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 11
Device Info
There are nine selections under Device Info in the left navigation bar. Each of them shows a different element of the gateway's setup, status or
nature of its connection with the provider and also with LAN devices. Device Info screens are read-only. It is not possible to interact with or
change the settings in this section.
Summary
Upon successful login, Device Info is the first screen to appear. This is screen is dedicated to the display of hardware and software details
associated with your gateway. In addition, the current status of the WAN connection (if present) is shown.
Wan Info
The Device InfoWAN status screen, provides a high level overview for the connection between your Internet Service Provider and the Gateway
device, itself. The WAN interface could physically be DSL or Ethernet and supports a number of Layer 2 and above configuration options covered

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 12
later in this document. Some features are supported only on specific SmartRG models. These exceptions and are specified in this guide.
The individual fields on this screen are defined as follows:
Field Name Description
Interface Displays the connection interface (layer 2 interface () through which gateway handles the traffic.)
Description Displays the service description (pppoe, ipoe, br)
Type Displays the service type (PPPoE, IPoE, Bridge)
VlanMuxId Displays the VLAN ID (Disabled, 0-4094)
IPv6 Displays the state of IPv6 (Enabled, Disabled)
Igmp Displays the state of IGMP (Enabled, Disabled)
MLD Displays the state of MLD (Enabled, Disabled)
NAT Displays the state of NAT (Enabled, Disabled)
Firewall Displays the state of the Firewall (Enabled, Disabled)
Status Displays the status of the WAN connection (Disconnected, Unconfigured, Connecting, Connected)
IPv4 Address Displays the obtained IPv4 address
IPv6 Address Displays the obtained IPv6 address
Statistics
The Statistic screens provide network interface information for LAN, WAN Service, xTM and DSL. All data is updated on a 15 minute interval.
LAN
Device Info -> Statistics -> LAN displays the TX/RX Bytes, Packets, Error and Drops for each LAN interface for your SmartRG modem. All local
LAN Ethernet ports, Ethernet WAN ports and w10 (Wireless Interface) for your SmartRG gateway are included.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 13
Use the Reset Statistics button near the bottom of the screen to reset these counters.
NOTE: Not all SmartRG gateway models support the SmartPort feature wherein a LAN port can be re-purposed to function as a WAN port (as
displayed in the Interface column below note, LAN3, LAN2, LAN1, WAN.) Only models SR5xxn and SR360n support this functionality.
The individual fields on this screen are defined as follows:
Field Name Description
Interface
(Received/ Transmitted)
LAN1, LAN2, LAN3, LAN4
Ethernet WAN if configured on your device
Wl0 is the Wireless LAN side Interface
Interface Displays available LAN interfaces
Bytes Bytes - (RX/ TX) total quantity of packets in Bytes
Pkts Pkts - (RX/ TX) total quantity of packets
Errs Errs - (RX/ TX) total quantity of error packets
Drops Drops - (RX/ TX) total quantity of dropped packets
WAN Service
Device Info -> Statistics -> WAN displays the TX/RX Bytes, Packets, Error and D rops for each WAN interface for your SmartRG Gateway. All
WAN interfaces configured for your SmartRG gateway are included.
Use the Reset Statistics button near the bottom of the screen to reset these counters.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 14
The individual fields on this screen are defined as follows:
Field Name Description
Interface
(RX/ TX) Displays available WAN interfaces (atm, ptm, eth)
Description
(RX/ TX) Displays the service description (pppoe, ipoe, b)
Bytes - (RX/ TX) total quantity of packets in Bytes
Pkts - (RX/ TX) total quantity of packets
Errs - (RX/ TX) total quantity of error packets
Drops -(RX/ TX) total quantity of dropped packets
Reset Statistics Resets the Statistics to zero.
xTM
The Device Info -> Statistics -> xTM displays the ATM/PTM statistics for your SmartRG Gateway. All WAN interfaces configured for your
SmartRG gateway are included.
Use the Reset button near the bottom of the screen to reset these counters.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 15
The individual fields on this screen are defined as follows:
Field Name Description
Port Number Displays the statistics specifically for Port 1, or both ports if Bonded
In Octets Total quantity of received Octets
Out Octets Total quantity of transmitted Octets
In Packets Total quantity of received Packets
Out Packets Total quantity of transmitted Packets
In OAM Cells Total quantity of received OAM Cells
Out OAM Cells Total quantity of transmitted OAM Cells
In ASM Cells Total quantity of received ASM Cells
Out ASM Cells Total quantity of transmitted ASM Cells
In Packet Errors Total quantity of received Packet Errors
In Cell Errors Total quantity of received Cell Errors
xDSL
Device Info -> Statistics -> xDSL displays the DSL statistics for your SmartRG Gateway. All xDSL (VDSL or ADSL) interfaces configured for your
SmartRG gateway are included. You are also able to reset these counters by selecting the Reset Statistics button located on the xTM screen as
shown below.
Use the Reset Statistics button near the bottom of the screen to reset these counters.
Also featured is an xDSL Bit Error Rate (BER) test which determines the quality of the xDSL connection. Scroll to the bottom of the table of
statistics and click xDSL BER Test. The test transfers idle cells containing a known pattern and compares the received data with this known
pattern. Comparison errors are then tabulated and displayed. The duration of the test is selectable from the drop-down menu at the test screen.
Selectable values range from 1-360 seconds.
The following figure and table depict and explain the fields on the screen..

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 16
The individual fields on this screen are defined as follows:
Field Name Description
Mode Displays the service type (ADSL_2plus, VDSL2)
Traffic Type Displays the connection type (ATM, PTM, ETH
Status Displays the status of the connection (Up, NoSignal, Initializing)
Link Power State Link output power state
Line Coding (Trellis) (Downstream/Upstream) Displays the state of Trellis Coded Modulation (On, Off)
SNR Margin (db) (Downstream/Upstream) Signal to Noise Ratio
Attenuation (db) (Downstream/Upstream) Estimate of average loop attenuation
Output Power (dBm) (Downstream/Upstream) Transmit power from the gateway to the DSL loop.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 17
Field Name Description
Attainable Rate (Kbps) (Downstream/ Upstream) The typically obtainable sync rate.
PhyR Status [Inactive, Active] Physical Layer Retransmission feature status. (Downstream/ Upstream)
Rate (Kbps) (Path 0/1, Downstream/Upstream) Current sync rate
MSGc (# of bytes in overhead channel
message) (Path 0/1, Downstream/Upstream)
B (# of bytes in Mux Data Frame) (Path 0/1, Downstream/Upstream)
M (# of Mux Data Frames in FEC Data Frame) (Path 0/1, Downstream/Upstream)
T (Mux Data Frames over sync bytes) (Path 0/1, Downstream/Upstream)
R (# of check bytes in FEC Data Frame) (Path 0/1, Downstream/Upstream)
S (ratio of FEC over PMD Data Frame length) (Path 0/1, Downstream/Upstream)
L (# of bits in PMD Data Frame) (Path 0/1, Downstream/Upstream)
D (interleaver depth) (Path 0/1, Downstream/Upstream)
Delay (msec) (Path 0/1, Downstream/Upstream)
INP (DMT symbol) (Path 0/1, Downstream/Upstream)
Super Frames (Path 0/1, Downstream/Upstream) Total number of super frames.
Super Frame Errors (Path 0/1, Downstream/Upstream)
Total number of super frames received with errors.
RS Words (Path 0/1, Downstream/Upstream)
Total number of Reed-Solomon code errors.
RS Correctable Errors (Path 0/1, Downstream/Upstream)
Total number of Reed-Solomon with correctable errors.
RS Uncorrectable Errors (Path 0/1, Downstream/Upstream)
Total number of Reed-Solomon with uncorrectable errors.
RS Codewords Received (Path 0/1, Downstream/Upstream)
Total number of Reed-Solomon Codewords received.
RS Codewords Corrected (Path 0/1, Downstream/Upstream)
Total number of Reed-Solomon Codewords corrected.
RS Codewords Uncorrected (Path 0/1, Downstream/Upstream) Total number of Reed-Solomon Codewords Uncorrected
HEC Errors (Path 0/1, Downstream/Upstream) Total number of Header Error Checksum errors
OCD Errors (Path 0/1, Downstream/Upstream) Total number of Out-of-Cell Delineation errors
LCD Errors (Path 0/1, Downstream/Upstream) Total number of Loss of Cell Delineation errors
Total Cells (Path 0/1, Downstream/Upstream) Total number of Cells
Data Cells (Path 0/1, Downstream/Upstream) Total number of Data Cells
Bit Errors (Path 0/1, Downstream/Upstream) Total number of Bit errors
Total ES (Downstream/Upstream) Total number of Errored Seconds
Total SES (Downstream/ Upstream) Total number of Severely Errored Seconds
Total UAS (Downstream/Upstream) Total number of Unavailable Seconds

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 18
Route
Th eDevice Info -> Route displays the LAN and WAN route table information configured in your SmartRG Gateway for both IPv4 and IPv6
implementation.
The individual fields on this screen are defined as follows:
Field Name Description
Destination (Including IPv6 Route) Displays the Destination IP addresses.
Gateway Displays the Gateway IP address.
Subnet Mask Displays the Subnet Masks.
Flag (Including IPv6 Route) Displays the status of the flags.
Metric (Including IPv6 Route) Displays the number of hops to reach the default gateway.
Service (Including IPv6 Route) Displays the service type.
Interface (Including IPv6 Route) Displays the WAN/LAN interface.
Next Hop (IPv6 Route only) Displays the next hop IP address.
ARP
Device Info -> ARP displays the host IP addresses and their hardware (MAC) addresses for each LAN Client connected to the SmartRG Gateway
via a LAN Ethernet port or Wireless LAN.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2014 19
The individual fields on this screen are defined as follows:
Field Name Description
IP address The IP address of the host.
Flags [Complete, Permanent, Published] Each entry in the ARP cache will be marked with one of these flags.
HW Address The hardware (MAC) address of the host.
Device [br(n), atm(n), eth(n), atm(n)] The system level interface by which the host is connected.
DHCP
Device Info -> DHCP displays a list of locally connected LAN hosts and their DHCP lease status, which are directly connected to the SmartRG
Gateway via a LAN Ethernet port or Wireless LAN.
The individual fields on this screen are defined as follows:
Field Name Description
Hostname Displays the Host name of each connected LAN device.
MAC Address Displays the MAC Address for each connected LAN device.
IP Address Displays the IP Address for each connected LAN device.
Expires In Displays the time until the DHCP lease expires for each LAN device.