SmartRG SR905acv User manual

Lorem ipsum
Lorem ips
Lorem ips
Lorem ips
um
um
um
SR905acv
Quick Start Guide

Installation
1. Connect the gateway to incoming services:
lFor Ethernet services, connect one end of an Ethernet cable to the WAN port on the gateway and connect
the other end of the cable to the wall jack installed by your provider.
lFor fiber services:
a. Slide open the small door at the right end of the gateway's back.
b. Insert the SFP transceiver (included with the gateway) into the port.
c. Connect one end of the fiber cable to the SFP transceiver and connect the other end of the cable
to the wall jack installed by your provider.
lFor phone (DSL) services, connect one end of a phone cable to one of the Phone ports on the gateway and
connect the other end of the cable to the wall jack installed by your provider.
2. Connect a LAN port on the gateway to your PC using an Ethernet cable.
3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the
gateway.
4. Turn on the unit by pressing the Power button on the back of the gateway.
Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to
complete.
If you are unable to connect to the Internet, make sure that all cable connections are in place and the gateway’s
power is turned on.

3
2
1
USB
LAN
WAN DC/
IN
PHONE
POWER
SFP
4
3

LED Indicators
Your SR905acv gateway has several status indicators (LEDs) on its top which are described below.
Legend: White White blinking Green Green blinking Red
LED Action Explanation
Power Device in CFE mode
Device powered on and ready for use
Internet DSL sync acquired and gateway on line
Data being transferred
Internet authentication / connection has failed
Lan 1-4 LAN Ethernet connected (at 1000 BASE-T)
Data being transferred (at 1000 BASE-T)
LAN Ethernet connected (at 10/100BASE-T)
Data being transferred (at 10/100BASE-T)

LED Action Explanation
WAN Device online (at 1000 BASE-T)
Device online (at 10/100 BASE-T)
WAN Ethernet connected (at 1000 BASE-T)
Data being transferred (at 1000 BASE-T)
WAN Ethernet connected (at 10/100BASE-T)
Data being transferred (at 10/100BASE-T)
2.4 GHz
5 GHz
WiFi enabled
Data being transferred
(locked WiFi / WPS)
WPS enabled
Data being transferred
SS 1 & 2 USB 3.0 device connected
Data being transferred
Phone 1 & 2 Phone line connected
Phone line in use
SFP SFP (fiber optic) connected
Data being transferred
5

Logging in to Your Gateway
To change the settings on your gateway, you must log into the gateway's interface. Make sure that you have completed
the steps in "Installation" before you begin.
1. Open your Internet browser and type 192.168.1.1 into the address line. The Sign in dialog box appears.
2. Enter the credentials shown below and click Sign in. Your service provider may use other settings. If so, contact
your provider for details.
User Name: admin Password: admin

To review the end user license agreement, click the License Agreement link at the bottom right corner of the
browser window. The agreement appears in a separate tab.
Note: If you've forgotten your password, click Forgot Password and follow the instructions to reset your gateway to the
factory defaults. Then, enter the credentials provided with the gateway when you first received it.
Configuring the WAN Manually
If the automatic connect process is unsuccessful, refer to the "Ethernet WAN" section of the SmartRG SR905acv
Gateway User Manual to manually establish a connection.
7

Wi-Fi Setup
1. In the left menu, click WiFi >Networks. The following page appears, showing information for the primary
network. The dual-band option is enabled by default.

2. Accept the default ID shown in the SSID field or enter the SSID for the network that you want to configure. You
will need this ID for Step 8.
3. Choose a passphrase and type it in to the Password field. You will need this passphrase for Step 8.
4. In the Encryption field, accept the default authentication type or select None. For security purposes, selecting
None is not recommended.
5. If you do not want this SSID visible to other users, click the slide button next to Broadcast SSID to disable it.
6. Skip the Client Isolation field. If needed, you can change this setting later.
Click the Apply button in the Pending changes... dialog box to save your settings.
7. To enable a guest or video wi-fi network:
a. Click the GUEST or VIDEO button.
b. Click the slide button next to Enabled.
c. Fill in the fields following the instructions in Steps 2-6.
d. Click the Apply button in the Pending changes... dialog box to save your settings.
8. Follow the WiFi connection instructions provided with your client device to connect to the gateway. Use the
SSID name you selected in Step 2. Then enter the passphrase that you created in Step 3 in the appropriate
location on the network setup screen of your WiFi client device.
9

Optional Wall Mount
Using a Phillips-head screwdriver, remove the mount
from the bottom of the gateway.
Insert the mount into the back of the gateway and
tighten the screw located in the bottom of the mount.
Using the template below, attach the two included
screws to the wall. Using wall anchors is
recommended.
Slide the mount down on to the screws.
4 1/8” (104mm)
Gateway
Front
1/16” (2-3mm) Wall Anchor

Record Your SR905acv Wi-Fi Settings
Predefined wireless settings If you change the wireless settings
Primary WiFi network name (SSID)
Primary WiFi Network key (password)
Guest WiFi network name (SSID)
Guest WiFi network key (password)
Video WiFi network name (SSID)
Video WiFi network key (password)
Additional Support
If you require further instructions, please contact your local ISP Support.
SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2021
11