SMC Networks VQ2000 Series User manual

How to Order Manifold
0824 F DS1VV5Q
4
2
Plug lead unit/Flip
VQ2000 Manifold
Series
Stations
01 1 station
··· ···
Kit/Electrical entry/Cable length
None (C kit only)
DIN rail mounting style
Special wiring specifications (Except double wiring)
With name plate
Built-in silencer, direct exhaust
Option
D (2)
K (3)
N
S (4)
Nil
Fkit
(D-sub connector)
Tkit
(Terminal block) Ckit (Connector) Skit
(Serial transmission unit)
Pkit
(Flat ribbon cable connector)
Connector entry direction
Top entry Side entry
U0
U1
U2
U3
S0
S1
S2
S3
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
Max. 16
stations
(2) (2)
(2)
Connector entry direction
Top entry Side entry
U0
U1
U2
U3
S0
S1
S2
S3
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
Max. 16
stations
0
A
B
C
D
F1
H
Without SI unit
With general type SI unit (Series EX300)
Mitsubishi Electric Corp.: MELSECNET/MINI-S3 Data Link System
OMRON Corp.: SYSBUS Wire System
SHARP Corp.: Satellite I/O Link System
NKE Corp.: Uni-wire System (16 output points)
NKE Corp.: Uni-wire H System
Max. 16
stations
CConnector kit
1
2
Applicable stations 1 to 8
Applicable stations 5 to 16
No. of terminals: 8, 1 row
No. of terminals: 16, 2 rows
Max. 16
Kit
T
Top entrySide entry
25P Note 1)
25P Note 1)
26P Note 1)
26P Note 1)
Top entrySide entry
The number of max. stations
differs from kit to kit.
(Refer to the table below.)
When two or more symbols are specified,
indicate them alphabetically. Example) -DNS
F, P, T, and S kits are of DIN rail include
suffix -D
Specify the wiring specifications in the
manifold specification sheet. (Except C kit)
F, P, T and S kits are provided with an
exhaust on one side, while C kits are with an
exhaust on both sides.
The valve is equipped
with an indicator
light/surge voltage
suppressor and the
voltage is 24 VDC.
The dust-protected type
SI unit is applicable, too.
For details, please
contact SMC.
Besides the above, F and P kits with different number of pins are available. For details, refer to page 2-4-68.
See page 2-4-69 for details.
Please consult with SMC for the following serial transmission kits: Matsushita Electric Works, Ltd.; Rockwell Automation, Inc.; SUNX Corporation; Fuji
Electric Co., Ltd.; OMRON Corporation.
Series VQ2000
Body Ported
Plug Lead Unit: Flip Type
Note 1)
Note 2)
Note 3)
Note 4)
Kit F Kit F
Kit P Kit P
Kit S(3)
Note 1)
Note 2)
Note 3)
Simple specials are available with
SMC Simple Specials System. For
details about applicable models,
please contact SMC.
For details about certified products
conforming to international standards,
visit us at www.smcworld.com.
P. 2-4-38 P. 2-4-42
P. 2-4-46
P. 2-4-50
P. 2-4-54
2-4-34

VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
2-4-35
Series VQ2000
Plug Lead Unit: Flip Type
Body Ported
How to Order Valves
C62140Y5L VQ
2VQ2000
2
1
2 position single
2 position double (latching)
Series
Type of actuation
Metal
seal
Rubber
seal
Seal
0
1
Metal seal
Rubber seal
Cylinder port
C4
C6
C8
Symbol
With One-touch fitting for ø4
With One-touch fitting for ø6
With One-touch fitting for ø8
Port size
Manual override
VQ2000
Electrical entry
Coil voltage
1
2 Note)
3
4 Note)
5
6
100 VAC (50/60 Hz)
200 VAC (50/60 Hz)
110 VAC (50/60 Hz)
220 VAC (50/60 Hz)
24 VDC
12 VDC
Function
Manifold Option
How to Order Manifold Assembly
Example
VV5Q24-08FU2-D
∗VQ2140-5LO-C6
∗VQ2240-5LOB-C6
··· 1 set (F kit 8 station manifold base no.)
··· 4 sets (Single solenoid part no.)
··· 4 sets (Double solenoid part no.)
Blanking plate assembly
VVQ2000-10A-4
Name plate [-N4]
VVQ2000-N4-Station
(1 to Max. stations)
Silencer (For EXH port)
Blanking plug
AN200-KM8
Individual SUP spacer
VVQ2000-P-4-C8
DIN rail mounting bracket
VVQ2000-57A-4
Block valve
VVQ2000-R-4-C8
Built-in silencer,
direct exhaust [-S]
Port plug
VVQ1000-58A
Individual EXH spacer
VQ2000-FPG-
Double check block
P
R
PR
0
1
1
2
VQ2 4 ---P
R
PR
KQ2P-06
08
Specifications DC
(1.0 W)
 (1)
(1.5 W)

(0.5 W)

AC Symbol
Standard type
Nil
High pressure type —
—
H(2)
Low wattage type Y(2)
For power consumption
of AC type, refer to
page 2-4-36.
Except double (latching).
For negative common specifications, refer
to “Option” on page 2-4-69.
Connector assembly will be required when
the F, P, T, S kits add a valve.
For part nos., refer to “Option” on page 2-
4-69.
The C kits is applicable
to 200/220 VAC.
LO and MO valves are used for F,
P, T, and S kits. The plug
connector and lead wire are
attached to the manifold.
For inch-size One-touch
fittings, refer to “Option” on
page 2-4-69.
The asterisk denotes the symbol for assembly. Prefix it
to the part nos. of the solenoid valve, etc.
Please indicate manifold base type, corresponding valve,
and option parts. When entry of part numbers becomes
complicated, indicate on the manifold specification sheet.
Note)
G: Grommet
C kit single only.
(Except AC)
L: L plug
connector
With lead wire
M: M plug
connector
With lead wire
LO: L plug
connector
Without connector
MO: M plug
connector
Without connector
With light/
surge voltage
suppressor
With light/
surge voltage
suppressor
With light/
surge voltage
suppressor
With light/
surge voltage
suppressor
Note 1)
Note 2)
Note 1)
Note 2)
Note)
Note)
A manual override for pilot valve is
provided to the standard model for
double type.
Note)
Nil: Non-locking
push type
(Tool required)
B: Locking
type (Tool required)
C: Locking type
(Manual)
CB (SUP) port
One-touch fitting for ø8
CB (SUP) port
One-touch fitting for ø8
1 2 3 ················ Stations
D side U side
D side U side
D side U side
Blocking indication label
3 m
Single solenoid (24 VDC)
VQ2140–5LO–C8 (4 sets)
Double solenoid (24 VDC)
VQ2240–5LOB–C8 (4 sets)
Manifold base (8 stations)
VV5Q24–08FU2–D
F kit
(D-sub connector)
D-sub
connector
cable
AXT100
–DS25–030
C8: One-touch
fitting for ø8
Individual EXH
spacer port size
EXH
outlet
Manual override body side
Pilot valve
Manual override
• For replacement parts, refer to page 2-4-
109.
P. 2-4-59

Manifold Specifications
Series Base model Type of connection Applicable
stations
Applicable
solenoid
valve
Porting specifications
Port size (1)
Port location
1(P), 3(R) 4(A), 2(B)
5 station
weight
(g)
VQ0000
VQ1000
VQ2000
Side
Side
Side
225
380
671
F kit–D-sub connector
P kit–Flat cable connector
T kit–Terminal block
C kit–Individual connector
S kit–Serial transmission unit
F kit–D-sub connector
P kit–Flat cable connector
T kit–Terminal block
C kit–Individual connector
S kit–Serial transmission unit
F kit–D-sub connector
P kit–Flat cable connector
T kit–Terminal block
C kit–Individual connector
S kit–Serial transmission unit
VV5Q04- VQ040
VQ041
VQ140
VQ141
VQ240
VQ241
VV5Q14-
VV5Q24-
C3 (ø3.2)
C4 (ø4)
M5 (M5 thread)
C3 (ø3.2)
C4 (ø4)
C6 (ø6)
M5 (M5 thread)
C4 (ø4)
C6 (ø6)
C8 (ø8)
1 to 16
stations
C6 (ø6)
Option
Built-in silencer,
direct exhaust
C6 (ø6)
Option
Built-in silencer,
direct exhaust
C8 (ø8)
Option
Built-in silencer,
direct exhaust
Note 1) Inch-size One-touch fittings are also available. For details, refer to page 2-4-69.
Note 2) See page 2-4-69 for details.
VV5Q04
VV5Q14
VV5Q24
(2)
Type of connection
Type of connection
Type of connection
1(P) port
1(P) port
3(R) port
3(R) port
4(A), 2(B) port
4(A), 2(B) port
4(A), 2(B) port
P port
3(R)
2-4-37
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Series
VQ0000
VQ1000
VQ2000
Porting specifications
Port
location
Side
Side
Side
Port size
1(P), 3(R)
C6
C6
C8
4(A), 2(B)
C3, C4, M5
C3, C4, C6, M5
C4, C6, C8
Applicable
stations
Max. 16 stations
Max. 16 stations
Max. 16 stations
Manifold Specifications
VV5Q04 VV5Q14
VV5Q14
VV5Q24
Flat Ribbon Cable (26 pins)
AXT100-FC26-1 to 3
Connector manufacturers’ example
• Hirose Electric Co., Ltd.
• Sumitomo 3M Limited
• Fujitsu Limited
• Japan Aviation Electronics Industry, Ltd.
• J.S.T. Mfg. Co., Ltd.
• Oki Electric Cable Co., Ltd.
Cable length (L) Assembly part no.
1.5 m
3 m
5 m
AXT100-FC26-1
AXT100-FC26-2
AXT100-FC26-3
Note
Cable 26 core
x 28AWG
Flat Ribbon Cable Connector Assembly (Option)
How to Order Manifold
1D14 08 SVV5Q P
0
1
2
VQ0000
VQ1000
VQ2000
Series
Stations
Connector entry direction
01 1 station
16 16 stations
··· ···
Cable (Length)
0
1
2
3
Without cable
With cable (1.5 m)
With cable (3 m)
With cable (5 m)
4Plug lead unit/Flip
Manifold
U
S
Top entry
Side entry
Positive common
specifications
Negative common
specifications
Terminal no.
Flat ribbon cable connector
Polarity
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(+)
(+)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
25
26
Cable assembly
Electrical wiring specifications
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
SOL.A
SOL.B
COM.
1 station
2 stations{
{
3 stations{
4 stations{
5 stations{
6 stations{
7 stations{
8 stations{
COM.
MIL flat ribbon cable connector reduces installation labor savings for
electrical connection.
Using the connector for flat ribbon cable (26P), (10P, 16P, 20P as an
option) conforming to MIL standard permits the use of connectors put
on the market and gives a wide interchangeability.
Top or side receptacle position can be selected in accordance with
the available mounting space.
Maximum stations are 16.
Flat ribbon cable connector assembly can be ordered individually or included
in a specific manifold model no. Refer to How to Order Manifold.
∗For other commercial connectors, use a 26 pins type with
strain relief conforming to MIL-C-83503.
Types with 10, 16, or 20 pin are also available.
For details, refer to page 2-4-69.
The total number of stations is
tabulated starting from station
one on the D side.
As the standard electrical wiring specifications, double wiring (connected to
SOL. A and SOL. B) is adopted for the internal wiring of each station for 8
stations or less, regardless of valve and option types. Mixed single and
double wiring is available as an option. For details, refer to page 2-4-69.
When using the negative common
specifications, use valves for negative
common. (Refer to page 2-4-69.)
When two or more symbols are
specified, indicate them
alphabetically.
Example) -DNS
P kits are DIN rail mounting styles,
so include suffix -D.
Specify the wiring specifications on
the manifold specification sheet.
For details, refer to
page 2-4-69.
1 2 3 ················ Stations
D side U side
VQ0000/1000/2000
Kit (Flat ribbon cable connector)
Note)
Note)
Note)
Triangle mark
indicator position
Connector
terminal no.
Terminal no.
Note) Note 1)
Note 2)
Note 3)
P
Red
DIN rail mounting style
Special wiring specifications
(Except double wiring)
With name plate
Built-in silencer, direct exhaust
(U side only)
Option
D(2)
K(3)
N
S
2-4-42

L1
L2
L3
L4
45
56
137.5
148
12345678910111213141516
61
72
150
160.5
77
88
162.5
173
93
104
187.5
198
109
120
200
210.5
125
136
212.5
223
141
152
225
235.5
157
168
250
260.5
173
184
262.5
273
189
200
275
285.5
205
216
287.5
298
221
232
312.5
323
237
248
325
335.5
253
264
337.5
348
269
280
362.5
373
285
296
375
385.5
Ln
L3
L4
112.5
123
12345678910111213141516
125
135.5
137.5
148
162.5
173
175
185.5
187.5
198
200
210.5
225
235.5
237.5
248
250
260.5
262.5
273
287.5
298
300
310.5
312.5
323
337.5
348
350
360.5
Ln
VQ2000
Dimensions: Side Entry Connector [-PS]
Dimensions: Top Entry Connector [-PU]
Formula L1 = 16n + 29, L2 = 16n + 40 n: Stations (Maximum 16 stations)
(M plug connector
AC, Latching)
(M plug connector)
(L plug connector
AC, Latching)
(L plug connector)
115 (L pug connector) 109 (M plug connector)
115 (L pug connector) 109 (M plug connector)
Applicable connector:
Flat ribbon cable (26P)
(Conforming to MIL-C-83503)
Indicator light
Indicator light
Flat ribbon cable unit
mounting screw
Manual override
DIN rail clamp screw
2-C8
P (SUP) port
2-C8
R (EXH) port 2n-C4, C6, C8
C4: One-touch fitting for ø3.2
C6: One-touch fitting for ø4
C8: One-touch fitting for ø6
P = 16
55.5 (M plug connector AC, Latching)
50.5 (M plug connector)
Top entry connector [-PU]
44 (L plug
connector)
49 (L plug connector AC, Latching)
≅5
8765432
1n
Stations
U side
D side
L3
L4
L2
L1
5.2
65
5.5
35
6.8
5.5
50
40.8
24.8
12 7.5
43.2
86
48
55.5
50.5
44
31
31
12
31
12
12
28
2-4-45
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Blanking plate assembly
VVQ2000-10A-4
Individual SUP spacer
VVQ2000-P-4-C8
Individual EXH spacer
VVQ2000-R-4-C8
Block valve
VQ2 4 ---
P
R
PR
1
20 1
P
R
PR
Valve no.
For SUP passage block
For EXH passage block
For SUP/EXH passage block
VQ2 4 ---P
1
20 1
VQ2 4 ---R
1
20 1
VQ2 4 ---PR
1
20 1
SUP passage
blocked
EXH passage
blocked
SUP/EXH
passage blocked
P block valve R block valve PR block valve
P block valve is mounted in the blocking position when
ordering an individual SUP spacer incorporated with a
manifold. When separately ordering an individual SUP
spacer, separately order a P block valve.
It is used when a blanking plate is mounted to
amanifold in advance for possible valve mounting,
etc.
When the same manifold is to be used for different
pressures, individual SUP spacers are used as SUP
ports for different pressures. (One station space is
occupied.)
Since the SUP passage on the spacer’s D side is
blocked in advance, it is mounted on the D side the
valves U side. (Refer to the application example.)
∗Specify the spacer mounting position and SUP
block plate mounting position on the manifold
specification sheet.
When valve exhaust affects other stations due to the
circuit configuration, this spacer is used for individual
valve exhaust. (1 station space is occupied.)
Since the EXH passage on the spacer’s D side is
blocked in advance, it is mounted on the D side of
the valve for individual supply while blocking the
valves U side. (Refer to the application example.)
∗Specify the spacer mounting position and EXH
block plate mounting position on the manifold
specification sheet.
∗When the electrical entry is F, P, T, S kit, and if
you choose the option with built-in silencer, no
exhaust port will be supplied on the D side end
plate. In this case, mount a spacer for individual
EXH on the 1st station.
For a flip plug-in unit, block plate is built in the valve
for blocking SUP and EXH passages. Since the no.
is classified by the passage to be blocked, specify it
by attaching the option no. to the valve no. The
block valve is constructed so that U sides of SUP
and EXH passages are blocked.
∗ Specify the number of stations on the manifold
specification sheet.
<Shut off label>
When using block plates for SUP, EXH passage,
indication label for confirmation of the blocking
position from outside is attached.
(One label for each)
∗When ordering a block plate incorporated with the
manifold no., a block indication label is attached to
the manifold.
∗Caution on handling P/RP block valve
When the electrical entry is F, P, T, S kit, and if
you choose the option with built-in silencer, no
exhaust port will be supplied on the D side end
plate. In this case, mount a spacer for individual
EXH on the 1st station.
Shut off label
Shut off label
C8 (SUP) port
One-touch fitting for ø8
C8 (SUP) port
One-touch fitting for ø8
SUP passage
blocked
EXH passage
blocked
Individual EXH
spacer
U side
D side
U side
D side
Individual SUP
spacer
Valve Valve
R block valve
(To be ordered using
the no. of the
standard valve.)
D side
P block valve
(To be ordered using
the no. of the
standard valve.)
Valve Valve
D side U side
D side U side
U side
Note)
Note)
Note)
R block valve is mounted in the blocking position when
ordering an individual EXH spacer incorporated with a
manifold. When separately ordering an individual EXH
spacer, separately order a R block valve.
Note)
Manifold Option Parts for VQ2000
Shut off label
2-4-63
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

∗When ordering assemblies incorporated with
a manifold, add suffix -D to the manifold no.
∗When ordering assemblies incorporated with
a manifold, add suffix -S to the manifold no.
Manifold Option Parts for VQ2000
Name plate [-N4]
VVQ2000-N4-Station (1 to Max. stations)
Blanking plug
KQ2P-04
06
08
4
6
8
KQ2P-04
KQ2P-06
KQ2P-08
16
18
20.5
32
35
39
6
8
10
ALD
Model
Applicable fittings
size ød
Dimensions
DIN rail mounting bracket
VVQ2000-57A-4
Built-in silencer, Direct exhaust [-S]
Silencer (For EXH port)
VQ2000
Series Model ALD
8 AN200-KM8 59.3 77.8 22 30
Effective
area
(mm2 )
Noise
reduction
(dB)
Applicable
fittings
size
ød
20
Dimensions
Port plug
VVQ1000-58A
A port, Plug
VQ2140-5L-C8-A
Example)
ø22
77.8
59.3
35.5
4.3
DIN rail clamp screw
It is a transparent resin plate for placing a label that
Indicates solenoid valve function, etc.
Insert it into the groove on the side of the end plate
and bend it as shown in the figure.
It is inserted into an unused cylinder port and
SUP/EXH ports.
Purchasing order is available in units of 10 pieces.
It is used for mounting a manifold on a DIN rail. The
DIN rail mounting bracket is fixed to the manifold end
plate. (The specification is the same as that for the
option -D.)
1 set of DIN rail mounting bracket is used for 1
manifold (2 DIN rail mounting brackets).
This is type with an exhaust port atop the manifold
endplate. The built-in silencer exhibits an excellent
noise suppression effect.
F, P, T and S kits are provided with exhaust on one
side.
Note) A large quantity of drainage generated in the air
source results in exhaust of air together with
drainage.
• For maintenance, refer to page 2-4-67.
This silencer is to be inserted into the EXH port (One-
touch fittings) of the common exhaust.
The plug is used to block the cylinder port when
usinga 4 port valve as a 3 port valve.
When ordering it incorporated with a manifold, suffix A
or B, the symbol of the plug port, to the valve no.
∗When ordering assemblies incorporated with
a manifold, add suffix N to the manifold no.
Exhaust port
2-4-64
Series VQ0000/1000/2000
Body Ported

Manifold Option
Double check block (Separated type)
VQ2000-FPG--
Specifications
Maximum operating pressure
Ambient and fluid temperature
Ambient and fluid temp.
Flow characteristics: C
Max. operating frequency
0.8 MPa
0.15 MPa
–5 to 50°C
3.0 dm3/(s·bar)
180 c.p.m
<Check valve operation principle>
Dimensions
Manifold
L1
L2
L3
46
75
85.5
68
87.5
98
90
112.5
123
112
137.5
148
134
162.5
173
156
175
185.5
178
200
210.5
200
225
235.5
244
262.5
273
266
287.5
298
288
312.5
323
Ln
310
337.5
348
332
362.5
373
354
375
385.5
376
400
410.5
Dimensions
Formula L1 = 22n + 24 n: Station
How to Order
Double check block
IN side port size
OUT side port size
Option
01
02
C6
C8
One-touch fitting for ø6
One-touch fitting for ø6
01
02
C6
C8
Rc 1/8
Rc 1/4
One-touch fitting for ø6
One-touch fitting for ø6
Nil
<Example>
VVQ2000-FPG- 06
Stations
01
16
1 station
16 stations
··· ···
<Ordering Example>
VVQ2000-FPG-06····6 stations manifold
∗VQ2000-FPG-C6C6-D: 3 sets
∗VQ2000-FPG-C8C8-D: 3 sets Double check block
N
Manifold
Cylinder side
(P2)
SUP side pressure
(P1)
Drop prevention
4(A)2(B)
VQ2000-FPG- 01 01 F
222
250
260.5
Residual
pressure release
manual override
DIN rail
clamp screw
( 9.5)
23 P = 22
L1
L2
L3
25
45
INININ
25
7.5
( 9.5)
45
65.5
37.5
5.5
80
C8: One-touch fitting for ø8
2-Rc 1/8, 1/4, C6, C8
C6: One-touch fitting for ø6
(For C6, C8)
C8: One-touch fitting for ø8
2-Rc 1/8, 1/4, C6, C8
C6: One-touch fitting for ø6
(For C6, C8)
Rc 1/8
Rc 1/4
Connection threads
Rc 1/8
Rc 1/4
Proper tightening torque (N·m)
7to 9
12 to 14
5(R1)
1(P)
3(R2)
5(R1)
1(P)
3(R2)
444
222 AAA
BBB
444
222 AAA
BBB
D
FWith bracket
DIN rail mounting style (For manifold)
Name plate
None
Caution
Single unit
(1.5)
37.5
17.5
C8: One-touch fitting assembly for ø8
C6: One-touch fitting for ø6
2-Rc 1/8, 1/4, C6, C8
2
B
A
4
4.5
(5) 69.5
(40)
6.5
(41.5)
(33)
22
( 9.5)
( 9.5) 80
39.5 (
For C6, C8)
(
For C6, C8)
Residual pressure release
manual override
2-M6 mounting hole
IN
20.5
(59.5)
58
7
58
10.5
2-M4 mounting hole
B
2
A
4
C8: One-touch fitting assembly for ø8
C6: One-touch fitting for ø6
2-Rc 1/8, 1/4, C6, C8
(1.5) 37.5
17.5
It is used on the outlet side piping.
Combining the double check block with built-in pilot double check
valve and a two-position single/double solenoid valve will prevent
the dropping at the cylinder stroke end when the SUP residual
pressure is released.
Note) Based on JIS B 8375-1981 (Supply
pressure: 0.5 MPa)
When two or more symbols are
specified, indicate them
alphabetically.
Example) -DN
Air leakage from the pipe between the valve and cylinder or from the fittings will prevent the
cylinder from stopping for a long time. Check the leakage using neutral household detergent, such
as dish washing soap.
Also check the cylinder’s tube gasket, piston packing and rod packing for air leakage.

Since One-touch fittings allow slight air leakage, screw piping (with M5 thread) is recommended when
stopping the cylinder in the middle for a long time.
 When screwing the fittings in the double check
block, proper tightening torque is as shown below:
If the exhaust of the double check block is
throttled too much, the cylinder may not
operate properly and may not stop
intermediately.

Set the cylinder load so that the cylinder pressure will be within two times that of the supply pressure.
D side U side Stations ·· 1 ··· 2 ··· 3 ·· n
~ =
~ =
~ =~
=
To CYL port
1234 5678910111213141516
Note)
2-4-65
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

DC circuit diagram
<Procedure>
Torque Applied to Tie-rod Bolt
Push type (Tool required)
Locking slotted type
Locking lever type (Option)
Manual override for double (latching) type
VQ0000
VQ1000
VQ2000
0.5 to 0.7 N·m
1.0 to 1.4 N·m
1.0 to 1.4 N·m
VQ0000
Bore ø3.2
Bore ø2.6
VQ1000
VQ2000
VQ1000
VQ2000
Bore ø3.2
10 mm
VQ1000
VQ2000
Bore ø2.6
Self-holding of the
main valve possible.
Pilot valve
Manual override
Manual override body side
Self-holding of the main valve is
impossible. (Returns to the main
valve position before operation.)
Manual override: Orange
Manual override: Green
Double (latching) type
Single solenoid type
B: Green
A: Orange
B: Green
A: Orange
Indicator lightIndicator light
M plug connector L plug connector
• If the manual override is turned by 180°clockwise
and the mark is adjusted to A, then pushed in the
direction of an arrow (
 ), it will be back to the reset
condition. (passage P A)
• If the manual override is turned by
180°counterclockwise and the mark is adjusted to
B, then pushed in the direction of an arrow (
 ), it will
be back to the reset condition. (passage P B)
(It is in the reset state at the time of shipment.)
Caution
The lighting positions are concentrated on one side for both single
solenoid and double (latching) type. In the double (latching) type, A
side and B side energization are indicated by two colors which match
the colors of the manual overrides.
• A-side energization: A light (orange) illuminates.
• B-side energization: B light (green) illuminates.
• Equipped with a wiring error prevention (stop
diode) mechanism and a surge absorption
(ZNR/surge absorption diode) machanism.
Applicable to negative COM specification models.
Note 1) Note 3)
Note 2)
In the case of double
(latching), the electromagnetic
valve channel is, A–(set):
P A, B R,
B–(reset):
P B, A R.
Different from the conventional double solenoid, the double type uses
a latching (self-holding system) solenoid. Although the appearance is
the same as the single solenoid, it is constructed so that the movable iron
core in the solenoid is held in the ON position on A and B sides by
instantaneous energization (20 ms or more).
The usage and function is the same as the double solenoid.
<Special Cautions for Latching Solenoid>
1. Select the circuit in which ON and OFF signals are not energized
simultaneously.
2. 20 ms energization time is necessary for self-holding.
3. Avoid using the latching solenoid valves in environments where
impact or collisions with the valve might occur. Also, do not use in
places where strong magnetic fields are present.
4. Even though the armature in the solenoid of this valve is held on to
B side, ON position (Reset), verify either A side, ON position or B
side, ON position by energizing prior to use.
5. After manual operation, the main valve will return to its original position.
Manual override on the pilot valve side can retain its switching
position after manipulation.
6. Please contact SMC for long-term energization applications.
7. If the metal seal type goes down below the minimum operating
pressure of supply air (0.1 MPa or less), the main valve will get back
the home position. (B side ON position) Therefore, in the event of
shutting the supply air or applying the air with being A side ON position
remained, cylinder may be pulsated. In the event of manipulating the
supply air, the valve's switching position has to be set in the home
position side (B side ON position side).
Without an electric signal for the solenoid valve the manual override
is used for switching the main valve.
Push down on the manual override
button with a small screwdriver until it
stops. Release the screwdriver and
the manual override will return.
Push down completely on the manual
override button with a small screwdriver.
While down, turn clockwise 90°to lock it.
Turn it counterclockwise to release it.
If the manual override is turned by 180°clockwise and
the mark is adjusted to 1, then pushed in the
direction of an arrow (), it will be locked in the ON
state. If the manual override is turned by 180°
counterclockwise and mark is adjusted to 0, locking
will be released and the manual override will return.
Push down completely on the
manual override button with a
small screwdriver. While down,
turn clockwise 90°to lock it.
Turn it counterclockwise to
release it.
In the case of a double (latching) type, a manual override is provided not
only on the body side but to the pilot as a standard. (VQ0000: Pilot valve
only). After manual operation, the main valve of the manual on the body side
returns to the position before the manual operation, however, the pilot valve
manual override maintains the change-over position.
Do not apply excessive torque when turning the locking type manual
override. (0.1 N·m or less)
Caution
Precautions
Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 2-9-2.
Double (Latching solenoid) Type
Warning
Double (Latching solenoid) Type
How to Remove
1. Loosen tie-rod bolt B. (Two to four turns)
2. After fully loosening the tie-rod bolt, take
off bolt A upward as shown above.
3. Slide the valves aside to make a 1
mm clearance between the valve to
be taken off and the others. As shown
above, remove the whole valve while
holding up the (a) side. (Avoid rough handing of the connector.)
Mounting
Reverse the sequence of steps above to
remount.
Tighten the tie-rod bolts with the
tightening torque at the right table while
using caution not to tighten the only one
side unevenly.
Light cover
Single solenoid Double (latching) solenoid
Light
Single Double (latching)
Simultaneous energization
protection circuit
A– (Set)
B– (Reset)
Tie-rod bolt A
Tie-rod bolt B
Caution
Light/Surge Voltage Suppressor
Caution
How to Mount/Remove Solenoid Valve
Note) Be careful not to push on the light cover while mounting/removing the
valve.
2-4-66
Series VQ0000/1000/2000
Body Ported

Element Part No.
Applicable
tubing O.D
Applicable tubing ø3.2
Applicable tubing ø4
Applicable tubing ø6
Applicable tubing ø8
VVQ1000-50A-C3
VVQ1000-50A-C4
VVQ1000-50A-C6
VVQ1000-51A-C4
VVQ1000-51A-C6
VVQ1000-51A-C8
VQ2000VQ1000
Fitting assembly part no.
Purchasing order is available in units of 10 pieces.
Caution
Attaching and detaching connectors
Type Element part no.
VQ1000 VQ2000VQ0000
VVQ0000-82A-4 VVQ1000-82A-4 VVQ2000-82A-4
Built-in silencer,
direct exhaust
(-S)
∗The minimum order quantity is 10 pcs.
For obtaining the flow rate, refer to pages 2-1-8 to 2-1-11.
How to Remove
<Procedure>
Mounting
To detach a connector, remove the pawl from
the groove by pushing the lever downward with
your thumb, and pull the connector straight out.
The cylinder port fittings are a
cassette for easy replacement.
(Except VQ1000)
The fittings are blocked by a clip
inserted from the top of the
valve. Remove the clip with a
screwdriver to remove fittings.
For replacement, insert the
fitting assembly until it strikes
against the inside wall and then
re-insert the clip to the specified
position.
1. Protect O-rings from scratches and dust to prevent air leakage.
2. The tightening torque for inserting fittings to the M5 thread
assembly should be 0.8 to 1.4 N·m
1. Loosen the clamp screw
on side (a) of the end
plate on both sides.
2. Lift side (a) of the
manifold base and slide
the end plate in the
direction of (2) shown in
the figure to remove.
1. Hook side (b) of the
manifold base on the
DIN rail.
2. Press down side (a) and
mount the end plate on
the DIN rail. Tighten the
clamp screw on side (a)
of the end plate.
The proper tightening
torque for screws is 0.4
to 0.6 N·m.
A silencer element is incorporated in the end plate on both sides of
the manifold base. A dirty and choked element may reduce cylinder
speed or cause malfunction. Clean or replace the dirty element.
Remove the cover from the side of the end plate and
remove the old element with a screwdriver, etc.
To attach a connector, hold
the lever and connector unit
between your fingers and
insert straight onto the pins of
the solenoid valve so that the
lever’s pawl is pushed into the
groove and locks.
Crimping the lead wire and
socket
Peel 3.2 to 3.7 mm of the tip
of lead wire, enter the core
wires and press contact it by
a press tool.
Be careful so
that the cover of lead wire
does not enter into the core
press contacting part.
Attaching and detaching lead wires with sockets
Attaching
Insert a socket in the square hole (Indicated as +, –) of
connector, push in the lead wire and lock by hanging the hook of
socket to the seat of connector. (Pushing-in can open the hook
and lock it automatically.) Then confirm the lock by lightly pulling
on the lead wire.
Detaching
To detach a socket from a connector, pull out the lead wire while
pressing the socket’s hook with a stick having a thin tip (approx. 1
mm). If the socket will
be used again, first
spread the hook
outward.
—
—
Cover
Cover
Pin
Pin
Concave
Concave
Connector
Connector
Lever
DC indicator
Socket
Part no.
DXT170-71-1
Lead wire 0.2 to 0.33 mm2
(Max. cover diameter ø1.7 mm)
Hook
Hook
Terminal
Core wire
crimping
area Crimping area
Core wire
Lead wire
Lead wire
0.2 to 0.33 mm2
(Max. cover diameter ø1.7 mm)
Socket
Cover
Fitting
assembly
Clip
(a)
(a)
(b)
(b)
(1)
(1)
(2)
(2)
Replacement of Cylinder Port Fittings
Caution
Built-in Silencer Replacement Element
How to Use Plug Connector
Mounting/Removing from the DIN Rail
How to Calculate the Flow Rate
Hook
Caution
Caution
Caution
2-4-67
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

Option
Different Number of Connector Pins
kit (D-sub connector) 15 pins
Fkit (Flat ribbon cable connector)
10 pins, 16 pins, 20 pins
P
How to order manifold How to order manifold
Stations
06 F SA DVV5Q14
Option
D
Option
Kit/Electrical entry
How to Order
Wiring specifications
Stations
06 PSC VV5Q14
Kit/Electrical entry
Location
Pins
10P
16P
20P
UA
UB
UC
Kit
P
Kit
P
SA
SB
SC
(Max. 4 stations)
(Max. 7 stations)
(Max. 8 stations)
Top entry Side entry
Pins
Cable length (L)
1.5 m
3 m
5 m
AXT100-FC10-1
AXT100-FC10-2
AXT100-FC10-3
17.2
AXT100-FC16-1
AXT100-FC16-2
AXT100-FC16-3
24.8
AXT100-FC20-1
AXT100-FC20-2
AXT100-FC20-3
30
10P 16P 20P
Location
Pins
15P UA SAKit F Kit F
(Max. 7 stations)
Top entry Side entry
Flat Ribbon Cable Assembly
Pins
Cable length (L)
1.5 m
3 m
5 m
AXT100-DS15-1
AXT100-DS15-2
AXT100-DS15-3
15P
∗For other commercial connectors, use a type conforming to MIL-C-24308.
D-sub Connector Cable Assembly
Wire Color by Terminal No. of
D-sub Connector Cable Assembly
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
Dot marking Lead wire color Terminal no.
Connector width (W)
F and P kits with the following number of pins are available. Besides the standard number (F = 25; P = 26) select the desired number of
pins and cable length from the cable assembly list. Place an order for the cable assembly separately.
D-sub connector, 15 pins
Connector location–Side (horizontal)
Without cable
How to Order
Flat ribbon cable, 20 pins
Connector location–Side (Horizontal)
Without cable
∗In the same way as the 25-pin models (standard) the terminal
no. 1 is for SOL.A at the 1st station, the terminal no. 9 for
SOL.B at the 1st station, and the terminal no. 8 for COM. ∗In the same way as the 26-pin models (standard) the terminal
no. 1 is for SOL.A at the 1st station, the terminal no. 2 for
SOL.B at the 1st station, and two pins from the max. terminal
numbers are for COM.
Wiring Specifications
10P, 16P, 20P
Multi-core vinyl cable
VVRF 0.3 mm2x 15C
ø9
~
=
Plug connector
HDA-CTH
(Made by Hirose
Electric)
Connector
HDA-15S
(Made by Hirose
Electric)
Terminal no.
Terminal no.
Red
AXT100-DS15-
1
to
3
∗For other commercial connectors, use a type with strain relief
conforming to MIL-C-83503.
2-4-68
Series VQ0000/1000/2000
Body Ported

Special Wiring Specifications
Negative Common Specifications
Inch-size One-touch Fittings
Refer to following model no. for inch-size One-touch fittings.
Plug Connector Assembly Model
Connector Assembly Part No.
Example)
VV5Q14-09FS0-D
Others, option symbols:
to be indicated alphabetically.
How to order negative COM valves
VQ1140
Negative common specifications
N 5LO C6
F kit
(D-sub connector)
T kit
(Terminal block)
P kit
(Flat ribbon cable connector)
S kit
(Serial)
kit
Type
Max.
points
F
25P
U
SF
15P
U
SP
26P
U
SP
20P
U
SP
16P
U
SPABC
10P
U
S
AS
14 8 8
16 16 16 16 1614
F kit
D-sub connector
(25P)
P kit
Flat ribbon cable connector
(26P)
T kit
Terminal block
(16 terminals)
How to order manifold
How to order valves
VV5Q14
P, R port size
08FSO DN 00T
VQ1140 5 N7
Cylinder port
Symbol
Part no.Specifications
Single
(2-wire)
ø1/4"
ø1/4"
ø5/16"
ø1/8"
ø5/32 " ø5/16" ø1/4"
N1 N3 N9N7
T2T1
VQ0000
VQ1000
VQ2000
VQ0000
A, B
port VQ1000
VQ2000
M
13
14
Double (latching)
(3-wire)
Positive common
Negative common
Positive common
Negative common
AXT661-14A-F
AXT661-14AN-F
AXT661-13A-F
AXT661-13AN-F
Applicable tubing
O.D. (Inch)
—
——
—
—
Note) Note) Note)
Note) Due to the limitation of internal wiring.
In the internal wiring of F kit, P kit, T kit and S kit, double wiring
(connected to SOL. A and SOL. B) is adopted for each station
regardless of the valve and option types.
Mixed single and double wiring is available as an option.
1. How to order valves
Indicate an option symbol, -K, for the manifold no. and be sure
to specify the mounting position and number of stations of the
single and double wiring by means of the manifold
specification sheet.
2. Wiring specifications
Connector terminal numbers are connected from solenoid
station 1 on the A side in the order indicated by the arrows
without skipping any terminal numbers.
KS
3. Max. number of stations
The maximum number of stations depends upon the number
of solenoids. Assuming one for a single and two for a double,
determine the number of stations so that the total number is
not more than the maximum number given in the following
table.
Specify the valve model no. as shown below for negative COM
specification. The standard manifold no. can be used. Please
contact SMC for negative COM S kit.
Lead wire length: 300 mm
The parts numbers above are applicable to VQ0000/1000 (2 to 16
stations) and VQ2000 (2 to 10 stations). VQ2000 (11 to 16 stations)
uses AXT661- A(N) -F425.
Connector assembly will be required when the F, P, T, S kits add
a valve.
Specify the type of valve and connector assembly.
Note)
Note)
2-4-69
Series VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD

DIN Rail Mounting
Example)
VV5Q14-08C-DOS
Others, option symbols:
to be indicated alphabetically.
When ordering DIN rail only
Example)
VV5Q14-08FS1-D09S
Others, option symbols:
to be indicated
alphabetically.
DIN rail for 9 stations
DIN rail no.: AXT100-DR-n
∗ Refer to the DIN rail dimension table for determining the length.
123456789
23 35.5 48 60.5 73 85.5 98 110.5 123
No.
L dimension
11 12 13 14 15 16 17 18 19
148 160.5 173 185.5 198 210.5 223 235.5 248
No.
L dimension
21 22 23 24 25 26 27 28 29
273 285.5 298 310.5 323 335.5 348 360.5 373
No.
L dimension
31 32 33 34 35 36 37 38 39
398 410.5 423 435.5 448 460.5 473 485.5 498
10
135.5
20
260.5
30
385.5
40
510.5
No.
L dimension
L = 12.5 x n + 10.5L Dimension
Option
Each manifold can be mounted on a DIN rail.
Order it by indicating an option symbol for DIN rail mounting
style, -D. In this case, a DIN rail which is approx. 30 mm longer
than the manifold with the specified number of stations is
attached. Besides, it is also available in the following cases.
 When DIN rail is unnecessary (C kit only.)
(DIN rail mounting brackets only are attached.)
Indicate the option symbol, -DO, for the manifold no.
When using DIN rail longer than the manifold with
specified number of stations
Clearly indicate the necessary number of stations next to the
option symbol, -D, for the manifold no.
 When changing the manifold style into a DIN rail mount
Order brackets for mounting a DIN rail. (Refer to “Option” on
pages 2-4-60, 61 and 64.)
No. VQ0000-57A4 (For VQ0000)
VQ1000-57A-4 (For VQ1000)
VQ2000-57A-4 (For VQ2000)
2 pcs. per one set
Pitch
2-4-70
Series VQ0000/1000/2000
Body Ported

VQ2000 (VV5Q24)/Plug Lead Unit, Flip Type
Valve U side end plate assembly D side end plate assembly Station
increase parts
Housing assembly and SI unit (3)
∗For how to increase the stations, refer to the instruction manual.
(F, P, T, S kit)
S kitP kit
FS (Side entry)
PS (Side entry)
Note 1)
Note 2)
Note 3)
Note 4)
F kitT kit
S kit is composed of a flat ribbon cable housing assembly (AXT100-2-PU20) of qSI unit and wP kit (20 pins).
Since no connector assembly is included, order it separately. (Refer to page 2-4-69.)
A housing assembly is not used for a C kit.
A DIN rail clamping bracket is attached to each.
Connector Note 2)
assembly
Connector Note 2)
assembly
Connector
assembly
Connector Note 2)
assembly
Note 4)
Note 4)
Note 4)
Note 1)
Note 4)
Note 2)
Series VQ
2-4-108

<Housing Assembly and SI Unit>
Housing assembly and SI unit no.
No. Manifold Part no. Description
(SA kit)
(SB kit)
(SC kit)
(SD kit)
SF1 kit
SH kit
P kit
F kit
T kit
T kit
U
S
U
S
EX330-S001
EX130-SMB1
EX130-STA1
EX130-SSH1
EX130-SUW1
EX130-SUH1
AXT100-2-P  (2)
AXT100-2-F (2)
AXT100-2-TB1
AXT100-2-TB2
U
S
U
S
General type SI unit (Series EX300)
SI unit for MELSECNET/MINI-S3 Data Link System (Mitsubishi Electric Corporation)
SI unit for SYSBUS Wire System (OMRON Corporation)
SI unit for Satellite I/O Link System (SHARP Corporation)
SI unit for 16 point Uni-wire System (NKE Corporation)
SI unit for 16 point Uni-wire H System (NKE Corporation)
Flat ribbon cable housing assembly = Number of pins: 26, 20, 16, 10
D-sub connector housing assembly = Number of pins: 25, 15
Terminal block assembly (8 terminals)
Terminal block assembly (8 terminals)
q
w
e
(1)
(3)
(3)
Note 1)
Note 2)
Note 3)
Note 4)
<D Side End Plate Assembly>
yD side end plate assembly no.
VVQ2000-3A-4-
Option
<U Side End Plate Assembly No.>
uU side end plate assembly no.
VVQ2000-2A-4-
<Station Increase Parts>
No. (3) Part no. Description Material Number (1)
VVQ2000-105A-4-(2)
!1
!2
Tie-rod bolt
Guide rod
Carbon steel
Stainless steel
2
1
r
t
Option
<Replacement Parts>
No. Part no. Description Material Number
VVQ2000-80A-3-2
VVQ2000-80A-3-4
i
o
Seal
Clip
HNBR
Stainless steel
12
12
Nil: Common exhaust
S: Built-in silencer, direct exhaust
(Applicable for C kit only)
Nil: Common exhaust
S: Built-in silencer, direct exhaust
Note) The !0’s fitting assembly is included.
Note) The !0’s fitting assembly is included.
Note) A set of parts containing 12 pcs. each is enclosed.
<Fittings Assembly>
!0 Fittings assembly part no.
VVQ1000-51A-
Port size
C4: Applicable tubing ø4
C6: Applicable tubing ø6
C8: Applicable tubing ø8 (1)
S kit is composed of a flat ribbon cable housing assembly (AXT100-2-PS20) of qSI unit and wP kit (20 pins). Place an order for
AXT100-2-PS20 separately.
Top/vertical entry connector for FU and PU while side (horizontal) entry connector for FS and PS.
Since no connector assembly is included, order it separately. (Refer to page 2-4-93.)
In the case of standard specifications and double wiring, ris for 1 to 4 stations and tis for 5 to 8 stations.
Note 1)
Note 2)
Note 3)
Each number of replacement parts are included in
one set.
: Number of stations (01 to 16)
!1 and !2 are in one set.
Note 1)
Note 2)
Standard SUP/EXH port is C8.
Purchasing order is available in units of 10 pieces.
2-4-109
Exploded View of Manifold Series VQ
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD