Smeg SUK81MBL5 User manual

Contents
1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________________________4
2. INSTALLATION OF THE APPLIANCE_________________________________________6
3. ADAPTATION TO DIFFERENT TYPES OF GAS ________________________________8
4. FINAL OPERATIONS_____________________________________________________10
5. DESCRIPTION OF CONTROLS ____________________________________________12
6. USE OF THE HOB _______________________________________________________14
7. USE OF THE OVEN______________________________________________________15
8. ELECTRONIC PROGRAMMER (ONLY ON EQUIPPED MODELS) _________________17
9. AVAILABLE ACCESSORIES _______________________________________________19
10. CLEANING AND MAINTENANCE ___________________________________________20
11. EXTRAORDINARY MAINTENANCE _________________________________________22
THESE INSTRUCTIONS ARE VALID ONLY FOR THE END USER COUNTRIES WHOSE
IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.
INSTRUCTIONS FOR THE INSTALLER: these are for the qualified technician who must
carry out a suitable check of the gas system, install the appliance, set it functioning and carry
out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands
and the correct procedures for cleaning and maintenance of the appliance.
3

Introduction
1. INSTRUCTIONS FOR SAFE AND PROPER USE
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN
ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE
COOKER. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE
USING THE COOKER. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION MUST
BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN
FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT
REGULATIONS IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING
FUNCTIONS: COOKING AND HEATING-UP OF FOOD. ALL OTHER USES ARE CONSIDERED
IMPROPER.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS WASTE
MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE.
IT IS COMPULSORY THAT THE APPLIANCE BE GROUNDED ACCORDING TO THE METHODS
REQUIRED BY SAFETY RULES.
THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET MUST BE THE SAME
TYPE AND MUST CONFORM TO CURRENT REGULATIONS.
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN.
NEVER UNPLUG BY PULLING ON THE CABLE.
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE
APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT
FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL
ASSISTANCE CENTRE.
NEVER ATTEMPT TO REPAIR THE APPLIANCE.
WHEN NOT IN USE, MAKE SURE THAT THE CONTROL KNOBS ARE IN THE CORRECT (OFF)
POSITION .
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY LIGHTED
AND CAUSE FIRES.
THE I.D. PLATE WITH TECHNICAL DATA, SERIAL NUMBER AND BRAND NAME IS POSITIONED
VISIBLY IN THE STORAGE COMPARTMENT.
THE PLATE MUST NOT BE REMOVED.
4

Introduction
DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB GRIDS.
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH THE
HEATING ELEMENTS INSIDE THE OVEN.
DO NOT USE CONTAINERS OR BROILERS THAT EXTEND BEYOND THE OUTER PERIMETER OF
THE HOB.
THE APPLIANCE IS DESIGNED FOR USE BY ADULTS. DO NOT ALLOW CHILDREN TO GO NEAR
OR PLAY WITH IT.
WHEN OPERATING THE GRILL ALL ACCESSIBLE PARTS COULD BECOME VERY HOT: KEEP
OUT OF THE WAY OF CHILDREN.
IF THE APPLIANCE IS TO BE POSITIONED ON A PLATFORM IT MUST BE INSTALLED IN SUCH A
WAY AS TO PREVENT IT FROM SLIPPING OFF THE FORMER.
DO NOT APPLY DECORATIVE PANELS TO THE LOWER PART OF THE COOKER AS THEY MAY
PREVENT CORRECT AIR CIRCULATION AND CAUSE OVERHEATING.
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND
RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND PROTECTIVE
FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.
The manufacturer declines all responsibility for damage to persons or things caused by non-
observance of the above prescriptions or by interference with any part of the appliance or by the use of
non-original spares.
5

Instructions for the installer
2. INSTALLATION OF THE APPLIANCE
It is the law that all gas appliances are installed by competent persons. Corgi gas installers
are approved to work to safe and satisfactory standards. All gas installation, servicing and
repair work must be in accordance with the gas safety regulations 1984 (installation and use)
as amended 1990.
This appliance may be installed next to a wall which is higher than the appliance, with a
minimum distance of 50 mm from the side of the appliance, as shown in the diagram showing
the correct installation conditions. Any wall cupboards or shelves must be at a distance of at
least 750 m above the work surface.
2.1 Electrical connection
Make sure that the power line voltage matches the specifications indicated on the rating plate
located inside the storage compartment.
This rating plate must never be removed.
If the appliance is connected to the supply by means of a fixed connection, install a multipolar
cut-out device on the line, with contact opening distance equal to or greater than 3 mm,
located near the appliance and in an easily reachable position.
Connection to the supply may be fixed or with plug and socket. In the latter case the plug and
socket must be suitable for the cable employed and conform with the regulations in force.
Regardless of the type of connection, earthing of the appliance is absolutely obligatory. Before
connection make sure that the supply line is suitably earthed. Avoid the use of reducers,
adapters or shunts.
1 - For operation on 230-240V ∼ :use a three-pole H05RR-F
or H05V2V2-F cable having a cross section 3 x 1.5 mm2.
6

Instructions for the installer
7
2.1.1 Ventilation requirements
The appliance may only be installed in a permanently ventilated room as specified by the relevant
regulations. The air flow into the room where the appliance is installed must be sufficient for proper
gas combustion and room ventilation. The air vent, protected by gratings, must be of suitable size (see
relevant regulations) and located so that they cannot be even partially obstructed.
The kitchen must be kept properly ventilated to disperse the heat and humidity produced by cooking
processes: in particular, a window should be opened or the speed of any fans increased after
prolonged use.
2.1.2 Combustion gas discharge
Combustion gases may be discharged by means of hoods connected to a natural draught chimney or
a fan extraction system. An efficient extraction system requires precise planning by an authorised
specialist and must comply with the distances and positions indicated by the regulations. After
installation, the specialist must issue a certificate of compliance.
2.1.3 Connecting to natural and LPG gas (Please see connection diagram)
FOR THE GAS CONNECTION, SEE THE TYPE OF APPLIANCE SUPPLY
TUBE
•Free hexagonal connector
Make the connection to the appliance using flexible bayonet style hose in
accordance to B.S. 669. The hose connection at the rear of the appliance has a
½” BSP internal thread. Please use seal Cbetween the flexible connection Land
the appliance supply tube B. When making the connection, make sure that no
stress of any kind is applied to the cooker and that the hose does not touch any
sharp edges.
If connecting to LPG the bayonet hose must have red bands on it.
•Smooth welded connector
Make the connection to the appliance using a flexible bayonet style hose in
accordance to B.S. 669. The hose connection at the rear of the appliance has a
½” BSP internal thread. Always apply a suitable sealing substance (such as
Teflon tape) between the flexible connection Land the appliance supply tube B.
When making the connection, make sure that no stress of any kind is applied to
the cooker and that the hose does not touch any sharp edges.
If connecting to LPG the bayonet hose must have red bands on it.

Instructions for the installer
8
3. ADAPTATION TO DIFFERENT TYPES OF GAS
Before performing any cleaning or maintenance work, disconnect the appliance from the
mains.
The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of
operation with other types of gas the burner nozzles must be changed and the minimum flame
adjusted on the gas taps. To change the nozzles, proceed as described below.
3.1 Replacement of nozzles on the hob
This operation requires no primary air regulation.
1. Extract the grids and remove all the caps and flame-spreader crowns;
2. unscrew the burner nozzles with a 7 mm socket wrench;
3. replace the nozzles according to the type of gas to be used and the description in
paragraph "3.2 Burner and nozzle characteristics table".
4. Replace the burners in the correct position.

Instructions for the installer
9
3.2 Burner and nozzle characteristics table
Burner
Rated
heating
capacity
(kW)
LPG –G30/G31 28/37 mbar
Nozzle
diameter
1/100 mm
By-pass
mm
1/100
Reduced
flowrate
(W)
Flowrate
g/h G30
Flowrate
g/h G31
Auxiliary 1.0 50 30 350 73 71
Semi rapid 1.75 65 33 450 127 125
Rapid 2.3 75 45 800 167 164
Rapid * 2.5 79 45 800 182 179
Triple crown 3.5 94 65 1500 254 250
Oven 3.2 87 48 850 233 229
Maxi oven 4.6 106 59 1200 378 371
Grill 3.7 95 // // 268 264
Burner
Rated
heating
capacity
(kW)
NATURAL GAS – G20 20 mbar
Nozzle diameter
1/100 mm
Reduced flowrate
(W)
Auxiliary 1.0 72 350
Semi rapid 1.75 97 450
Rapid 2.3 103 800
Rapid * 2.5 108 800
Triple crown 3.5 140 1500
Oven 3.2 130 850
Maxi oven 4.6 155 1200
Grill 3.7 145 //
* Nozzle supplied only on some models
3.3 Arrangement of the burners on the hob
BURNERS
1Auxiliary
2Semi rapid
3Rapid
4Triple crown

Instructions for the installer
1
4. FINAL OPERATIONS
After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the
grids.
Following adjustment to a gas other than the preset one, replace the gas adjustment label
fixed to the appliance with the one corresponding to the new gas. This label is in the packet
together with the nozzles.
4.1 Regulation of the hob burner minimum level for natural gas
Light the burner and turn it to the minimum position . Extract the gas
tap knob and turn the adjustment screw at the side of the tap rod until
the correct minimum flame is achieved.
Replace the knob and check burner flame stability: (rapidly turning the
knob from maximum to minimum position, the flame should not go out).
Repeat the operation on all the gas taps.
For models with valves, keep the knob at minimum level for about 1 minute to keep the flame
lit and to activate the safety device.
4.2 Regulation of the hob burner minimum level for LPG
In order to adjust the minimum with LPG, the screw at the side of the tap rod must be turned
clockwise all the way.
The bypass diameters for each individual burner are shown in paragraph “3.2 Burner and
nozzle characteristics table". Once the regulation has been completed, restore the seal on the
by-passes using paint or similar materials.
4.3 Mounting the rear top skirtboard (where applicable)
•Loosen nuts B.
•Position the skirt above the top, taking care to align pins Cwith holes D.
•Secure the skirt to the top by tightening screws A.
0

Instructions for the installer
11
4.4 Wall fixing
•Stretch out the chain attached to the cooker horizontally so that the other end touches the
wall.
•Mark the wall in the position where the hole is to be drilled.
•Drill the hole, insert a wall plug and attach the chain.
•Move the cooker up against the wall.

Instructions for the user
1
5. DESCRIPTION OF CONTROLS
5.1 Front control panel
All the cooker controls and commands are on the front panel.
If the cooker is equipped with an electronic programmer, before using the oven make sure that
the symbol ; appears on the display. See paragraph “8.1 Clock adjustment”.
DESCRIPTION OF SYMBOLS
FRONT RIGHT BURNER
CENTRAL BURNER
BACK RIGHT BURNER
VARIABLE GRILL
BACK LEFT BURNER
ELECTRIC OVEN THERMOSTAT
FRONT LEFT BURNER
ELECTRIC OVEN FUNCTION KNOB
HOB BURNER COMMAND KNOB
The flame is lit by pressing the knob and turning it anticlockwise to minimum
flame . To adjust the flame turn the knob between maximum ( ) and
minimum ( ). The burner goes out when the knob is returned to the position
.
ELECTRIC OVEN THERMOSTAT KNOB
Selection of cooking temperature is carried out by turning the knob
clockwise to the required temperature, between 50° and 260°C.
If the appliance has an electric oven, the warning light will come on when
the oven is heating up. When it goes out it means that the required
temperature has been reached. Regular flashing means that oven
temperature is being constantly maintained at the programmed level.
2