socomec ATyS p User manual

Clip for
storage of
the
emergency
handle
STEP 3
542 000 E - 09/15 - EN
QUICK START 800A-3200A
EN
STEP 1
Installation
50.5
20
138
214
ATyS p 1250 AATyS p 800 to 1000 A
ATyS p 800 to 1600 A
ATyS p 2000 to 3200 A
ATyS p 1600 to 3200 A
33 8.58.5
50
3310
ø 9
ø 15
16 x 11
60
28.5 15.7515.75
28.515
15
55
12.5
25 25
30
30
45
45
90
ø12.5
Door cut-out for
front panel.
==
250
M
T
51,5
280
C 21
M
T
250
51.5
C2
1
Dimensions
in mm.
ATyS p
Motorised Source Changeover Switch
Automatic Transfer Switching Equipment
www.socomec.com
To download, brochures, catalogues and technical manuals:
Printing informations: 1 color Black. White paper 90g/m2.
Printing size: 420x297. Final size 210x297. This page visible first.
Non contractual document.
Subject to change without notice.
Caution:
Ensure that the
product is installed on
a flat rigid surface.
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
• Packaging and contents are in good condition.
• The product reference corresponds to the order.
• Contents should include:
Qty 1 x ATyS p
Qty 1 x Emergency handle and fixing clip
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
• This product must always be installed and
commissioned by qualified and approved personnel.
• Maintenance and servicing operations should be
performed by trained and authorised personnel.
• Do not handle any control or power cables connected to
the product when voltage may be, or may become
present on the product, directly through the mains or
indirectly through external circuits.
• Always use an appropriate voltage detection device to
confirm the absence of voltage.
• Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
• In case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
• Bridging bars and connection kits.
• Control voltage transformer (400Vac -> 230Vac).
• DC power supply (12/24Vdc -> 230Vac).
• Mounting spacers to raise the product x 10mm.
• Phase barriers.
• Terminal shrouds / Terminal screens.
• Auxiliary contacts (Additional).
• Padlocking in 3 positions (I - O - II).
• Lockout accessories (RONIS - EL 11 AP).
• Door escutcheon frame.
• ATyS D20 Interface (remote control / display unit).
• RJ45 cable for ATyS D20 => ATyS p.
• Voltage sensing kit.
• Current transformers.
• Plug-in optional modules: RS485 MODBUS
communication, 2 inputs/2 outputs, Ethernet
communication, Ethernet communication + RS485
JBUS/MODBUS gateway,Analogue outputs, Pulse
outputs.
For further details refer to the product instruction manual
under chapter "Spares and Accessories"
STEP 1
Cabinet / Back
Plate Installation
STEP 3
COMMAND /
CONTROL terminal
connections
STEP 2
Power Terminal
Connections
STEP 4
Power SUPPLY and
ATS Controller
Terminal
Connections
STEP 5
CHECK
STEP 6
PROGRAMMING
A - Software
B - Keypad
Installation and Commissioning STEP 7A
AUT Mode
(Automatic Control)
STEP 7C
Manual Mode
STEP 7B
AUT Mode
(Remote Control)
STEP 7D
Padlocking Mode
STEP 4
STEP 3STEP 4
CONTROL / COMMAND Terminals
Ensure that the product is in Manual Mode.
Power Supply, Sensing and Control wiring (ATS Controller)
5
6
43 2 1
2
7
104103
312313 314315 316317 63A64A 24 14 04 13
8 9
10
RJ 102101
105106
414413415416417
64B63B
201202 205206204203210209208207
12
13
14
15
11
1
F1
F2
19
20
16
17
18
L1 L2 L3 N
L1 L2 L3 N
23 23
24 24
72 71 74
LOAD
21
22
R1 R2 S1 S2 T1 T2
Opt. 3 Opt. 2 Opt. 1
4
Opt. 4
321
Connect the product with a cable of section of 1,5 to 2,5 mm2.
Screw M3 - Tightening torque: min.: 0.5 Nm - max.: 0.6 Nm
Example: Control wiring for a 400VAC application having a 3 phase and neutral supply.
1preferred source 2alternate source
1. Position 0 order
2. Position 1 order
3. Position 2 order
4. Zero position priority order
5.
Remote Control Enable (Priority over Auto)
6. Product Available output (Motor)
7. Position II aux contact
8. Position I aux contact
9. Position 0 aux contact
10. O/P to ATyS D20 remote unit
11. Programmable Output Contact.
By default set to ATS Product
Available - Normally Open
12-15. Programmable Inputs 1-4
16-17. Programmable Inputs 5-6
18. Aux. Supply (207/210) to be used
with ATyS optional I/O modules
19. Contact “Start/Stop Genset” : if S1
is not available the NC contact le
contact (71-72) is close
20. Contact “Start/Stop Genset” : if S1
is not available the NO contact le
contact (71-74) is open
21. Option Module Slots 1 to 4
22. Current Transformer incoming cable
connections
23. Voltage Sensing Inputs
24. Power Supply Inputs
ATS Module
ControlInputs
(Programmable)
Programmable Inputs
To opt. Module/Common
Progr. Inputs (208-209)
To opt. Module positive
ATS Module
Output Contact
(Programmable)
Genset
Start/Stop Signal
NC
Common
NO Remote interface
RJ45 - to ATyS D20
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10
To D20
64B 63B 64B 63B
64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10 To D20
64B 63B 64B 63B 64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Programmable Inputs
To opt. Module/Common
Progr. Inputs (208-209)
To opt. Module positive
Start/Stop Signal
Slots for optional modules
See on the back "Optional modules"
Recommanded to use SOCOMEC
Voltage Sensing Kit
(refer to ATyS p
accessories
for details)
ATS Power Supply
InputI
Power supply I - L
Power supply I - N
208-277VAC ±20%:
50/60 Hz
ATS Power Supply
InputII
Power supply II - L
Power supply II - N
208-277VAC ±20%:
50/60 Hz
ATS Voltage Sensing
Input
Source supply II
S II - Phase 1
S II - Phase 2
S II - Phase 3
600 VAC (ph-ph) max
S II - Neutral
332 VAC (ph-n) max
ATS Voltage Sensing
Input
Source supply I
S I - Phase 1
S I - Phase 2
S I - Phase 3
600 VAC (ph-ph) max
S I - Neutral
332 VAC (ph-n) max
ATyS D20
Remote Control /
Display Unit
Current Transformer
incomingcable connections
1
2
Recommended
orientation Ok Ok
800 A 1000 A 1250 A 1600 A 2000 A 2500 A 3200 A
3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P
M255 335 255 335 255 335 347 467 347 467 347 467 347 467
T80 80 80 80 80 80 120 120 120 120 120 120 120 120
C391 391 391 391 391 391 391 391 523 523 523 523 523 523
STEP 2
Power Terminal Connections
To be connected using terminal lugs, rigid or flexable busbars.
FRAME B6 FRAME B7 FRAME B8
800 A 1000 A 1250 A 1600 A 2000 A 2500 A 3200 A
Minimum cable section Cu (mm
2
) at Ith
(IEC60947-1)
2x185 - - - - - -
Recommended cable section Cu(mm
2
) at Ith
2x50x5 2x60x5 2x60x7 2x100x5 3x100x5 4x100x5 3x100x10
Maximum cable section Cu (mm
2
)
2x300 4x185 4x185 6x185 - - -
Maximum Cu busbar width (mm)
63 63 63 100 100 100 100
Type of screw
M8 M8 M10 M12 M12 M12 M12
Recommended tightening torque(N.m)
8.3 8.3 20 40 40 40 40
Maximum tightening torque (N.m)
13 13 26 45 45 45 45

STEP 7C
Manual Mode
AUT
90°
90°
II
I
0
Ensure that the emergency handle is
not inserted in the product and turn
the mode selector to the AUT position.
LED “Power” Green: ON
LED Manuel/Default: OFF
STEP 7A
AUT Mode
(AutomaticControl)
STEP 7B
AUT Mode
(RemoteControl)
To enable control, close contact 312 with 317.
For contactor logic bridge contact 316 with 317.
To operate: close the contact corresponding to
the desired position.
To force the product to 0 position “OFF” bridge
contact 313 with 317.
Imp. ≥60ms maintened
order I
position I
order 0
position 0
order II
position II
Contactor logicImpulse logic
POWER
AUT
Ø 4 ... 8mm
PROG
OK
AUT
READY
ATySt
0
1
5
10
20
60
0
1
5
10
20
60
G: U 10% F 5%
H: U
20% F 10%
E:
F:
REMOTE CONTROL
A: 3 Ph
B: 1 Ph
C: Neutral
D: Neutral
Motorised Changeover Switch
ATyS
1600A Ref : 95054160
Un N° PP / PN
1: 220 / 127
2: 380 / 220
3: 400 / 230
4: 415 / 240
5: 480 / 277
6: 208 / 120
7: 220 / 127
8: 230 / 132
9: 240 / 138
10: 380 / 220
11: 400 / 230
12: 415 / 240
13: 480 / 277
5
6
7
8
9
10
11
12
13
14
15
16
18
20
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
3
3
4
4
5
5
6
6
7
7
8
8
9
10
N°: Δ
U Δ F %
XXX
50 Hz60 Hz
XXXXXXXX
Set Pot
PROG
AUT
Press
60ms
Press
2s
Ready !
PROG
Set Dip
1 2 3
45
PROG
POWER
AUT
Ø 4 ... 8mm
PROG
OK
AUT
READY
ATySt
0
1
5
10
20
60
0
1
5
10
20
60
G: U 10% F 5%
H: U
20% F 10%
E:
F:
REMOTE CONTROL
A: 3 Ph
B: 1 Ph
C: Neutral
D: Neutral
Motorised Changeover Switch
ATyS
1600A Ref : 95054160
Un N° PP / PN
1: 220 / 127
2: 380 / 220
3: 400 / 230
4: 415 / 240
5: 480 / 277
6: 208 / 120
7: 220 / 127
8: 230 / 132
9: 240 / 138
10: 380 / 220
11: 400 / 230
12: 415 / 240
13: 480 / 277
5
6
7
8
9
10
11
12
13
14
15
16
18
20
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
3
3
4
4
5
5
6
6
7
7
8
8
9
10
N°: Δ
U Δ F %
XXX
50 Hz60 Hz
XXXXXXXX
Set Pot
PROG
AUT
Press
60ms
Press
2s
Ready !
PROG
Set Dip
1 2 3
45
PROG
POWER
AUT
Ø 4 ... 8mm
PROG
OK
AUT
READY
ATySt
0
1
5
10
20
60
0
1
5
10
20
60
G: U 10% F 5%
H: U
20% F 10%
E:
F:
REMOTE CONTROL
A: 3 Ph
B: 1 Ph
C: Neutral
D: Neutral
Motorised Changeover Switch
ATyS
1600A Ref : 95054160
Un N° PP / PN
1: 220 / 127
2: 380 / 220
3: 400 / 230
4: 415 / 240
5: 480 / 277
6: 208 / 120
7: 220 / 127
8: 230 / 132
9: 240 / 138
10: 380 / 220
11: 400 / 230
12: 415 / 240
13: 480 / 277
5
6
7
8
9
10
11
12
13
14
15
16
18
20
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
3
3
4
4
5
5
6
6
7
7
8
8
9
10
N°: Δ
U Δ F %
XXX
50 Hz60 Hz
XXXXXXXX
Set Pot
PROG
AUT
Press
60ms
Press
2s
Ready !
PROG
Set Dip
1 2 3
45
PROG
STEP 7D
Padlocking Mode
(as standard: in position O)
3x
Ø 4-8 mm
1. MANUAL Mode LED indication. (Yellow
steady light when in Manual Mode).
2. AUTO Mode LED indication Green steady
light when in Auto mode with no timers
running.
Green flashing light when in Auto with timers
running.
3. LOCAL / REMOTE CONTROL Mode LED
indication.
Yellow steady light when in Local / Remote
control mode.
Remote control mode is achieved with the
Auto/Manu selector switched to Auto and
terminals 312 closed with terminal 317.
Remote control orders are received through
closing 314 to 316 with 317.
REMOTE Control is also achievable through
EasyConfig ATyS p software when
connected to the product through Ethernet or
MODBUS. (Optional modules). Local Control
selectable and operable through the ATyS
p keypad.
4. TEST ON LOAD CONTROL Mode LED
indication. (Yellow steady light when in TON/
EONmode)
5. TEST OFF LOAD CONTROL Mode LED
indication. (Yellow steady light when in TOF/
EOF mode).
6. Load Supply On LED. (Green when the load
is supplied).
7. Switch 1 LED position indication. (Green
when in position 1).
8. Source supply I availability LED indication.
(Green when supply I voltage is within the
set limits).
9. Zero position LED indication. (Yellow when
in position 0).
10. Switch 2 LED position indication. (Green
when in position 2).
11. Source supply II availability LED indication.
(Green when supply II voltage is within the
set limits).
12. LCD Display Screen : (Status,
measurement, timers, counters, events,
faults, programming …. )
13. MODE key to shift between operation
modes.
14. Navigation Keys to browse through the
ATyS p menus without software.
15. FAULT LED indication. (Red steady light
in case of an ATS controller internal fault.
Switch the product from Auto to Manual
and back to Auto to reset a fault condition).
16. READY LED indication. (Green steady
light : Product is powered and in AUTO,
Watchdog OK, The Product is Available to
changeover).
17. Enter Key used to enter Prog Mode (Press
and hold for 5 seconds) and to validate the
settings programmed through the keypad.
18. ESC key used to escape from a specific
screen up to the main menu.
19. Lamp test key to check the LED’s and LCD
screen.
20. Green LED Indication: Power
21. Red LED Indication: Product Unavailable /
Manual Mode / Fault Condition
22. Auto / Manual mode selector switch
(Key version available as an option)
23. Padlocking facility
(Up to 3 padlocks of dia. 4 - 8mm)
24. Emergency manual operation shaft location
(Accessible only in manual mode)
25. Switch position indication window:
I (On switch I) O (Off) II (On switch II).
2223
24
25
8
7
2
3
4
5
1
6
15
20
21
17
18
13
14
19
1110 129
Programming the ATyS p
1SETUP 2VOLT. LEVELS 3FREQ. LEVELS 4PWR. LEVELS 5TIMERS VALUE 6I-O 7COMM 8DATE/TIME
NETWORK 4NBL O V. U I115% OV. F I105% OV.P I0000 kVA 1FT 0003 SEC IN 1 --- NO DHCP NO (9) YEAR
AUTOCONF NO (7) OV. U HYS I110% OV. F HYS I103% OV.P HYS I0000 kVA 1RT 0180 SEC IN 2 --- NO IP 1-2 192.168.
(9)
MONTH
NEUTRAL AUTO UND. U I085% UND. F I095% OV.P I I 0000 kVA 2FT 0003 SEC IN 3 --- NO IP 3-4 .002.001 DAY
ROT PH. --- UND. U HYS I095% UND. F HYS I097% OV.P HYS I I 0000 kVA 2RT 0005 SEC (2) IN 4 --- NO GAT1-2 000.000.
(9)
HOUR
NOM. VOLT 400 V UNB. U I00% O V. F I I 105% 2AT 0005 SEC (1) IN 5 --- NO GAT3-4 .000.000 MINUTE
NOM. FREQ 50 Hz UNB. U HYS I00% OV. F HYS I I 103% 2CT 0180 SEC (1) IN 6 --- NO MSK1-2 255.255.
(9)
SECOND
APP M-G OV. U I I 115% UND. F I I 095% 2ST 0030 SEC (1) IN 7 --- NO (8) MSK3-4 .255.000
PRIO TON NO (1) OV. U HYS I I 110% UND. F HYS I I 097% ODT 0003 SEC IN 8 --- NO (8) ADDRESS 005
PRIO EON NO (3) UND. U I I 085% TOT UNL (1) IN 9 --- NO (8) BDRATE 9600
PRIO NET 1 (2) UND. U HYS I I 095% TOT 0010 SEC (1) IN10 --- NO (8) STOP BIT 1
RETRANS NO UNB. U I I 00% T3T 0000 SEC (1) IN11 --- NO (8) PARITY NONE
CT PRI 100 UNB. U HYS I I 00% TFT UNL (1) IN12 --- NO (8)
CT SEC 5 TFT 0600 SEC (1) IN13 --- NO (8)
S1=SW2 NO E1T 0005 SEC (3) IN14 --- NO (8)
BACKLGHT INT E2T UNL (3) OUT 1 POP NO
CODE P 1000 E2T 0010 SEC (3) OUT 2 --- NO (8)
CODE E 0000 E3T 0005 SEC (3) OUT 3 --- NO (8)
BACKUP SAVE E5T 0005 SEC (4) OUT 4 --- NO (8)
E6T LIM (4) OUT 5 --- NO (8)
E6T 0600 SEC (4) OUT 6 --- NO (8)
E7T 0005 SEC (4) OUT 7 --- NO (8)
LST 0004 SEC (5) OUT 8 --- NO (8)
EET 0168 H (6) OUT 9 --- NO (8)
EDT 1800 SEC (6)
16
(1) When «APP» is set to «M-G»
(2) When «APP» is set to «M-M»
(3) When one of the I/P is set to «EON»
(4) When one of the I/P is set to «EOF»
(5) When one of the O/P is set to «LSC»
(6) When one of the O/P is set to «EES»
(7) If the product is in manual mode
(8) With optional I/O modules
(9) With Ethernet module
The ATyS p is to be programmed powered up and after wiring
verifi cation tests. This may either be done through the front of
the ATS Controller using the keypad or with the user-friendly Easy
Confi g software.
For convenience, we recommend to use the Easy Confi g software.
(Downloadable free from www.socomec.com).
The ATyS p is delivered with default setting values based on
most used customer application requirements. The minimum
confi guration parameters that must be programmed are the type
of network and application together with the voltage and frequency
nominal values. ATyS p Auto Confi guration makes the setup of Volts,
Hz, Phase rotation and Neutral Position quick and easy.
A - Programming with Easy Config Software
To program the ATyS p using Easy Confi g software simply follow
the setting boxes from left to right until all desired settings in each
window have been completed. Help pop ups are included to show
the minimum and maximum setting values allowed. The software
includes most SOCOMEC products so before programming click
NEW and select the product “ATyS p” from the list of products
available.
When the ATyS p is powered and communicating, the software will
include a screen to monitor and display the ATyS p status.
Control through software (such as changing switch position I-O-II) is
also possible when in Super User Mode.
To change the confi guration: Enter code (factory code = 1000) using navigation push buttons (14).
Programming exit: Press and hold for 5 s “Validation” push button (17).
Note 1: Values as listed above are the setting values by default.
Note 2: Ensure that the Default Network Setting and Application match the installation or change
accordingly before using Auto Confi guration.
B - Programming with the ATyS p keypad
Programming the ATyS p
STEP 6
Check
Whilst in manual mode, check the
wiring and if ok power up the
product.
LED “Power” Green: ON
LED Manuel/Fault Red: ON
STEP 5
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10 To D20
64B 63B 64B 63B 64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10 To D20
64B 63B 64B 63B 64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10 To D20
64B 63B 64B 63B 64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
See instruction sheet
ATS CONTROLLER
To D10 To D10 To D20
64B 63B 64B 63B 64B 63B
417 416 415 414 413
417 416 415 414 413
207 208 209 210
417 416 415 414 413
207 208 209 210
7172 74
7172 74
ATyS t
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS p
Dual auxiliary supply:
Uc 208-277V~ +/-20% 50/60Hz
Power comsumption: 22VA
See instruction sheet
ATS CONTROLLER
ATyS g
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Power 208-277V~ +/-20%
Optional Modules
Communication between the software and the ATyS p may be done through the Ethernet/Modbus TCP or Modbus RTU modules
that are available as an option. The ETHERNET / MODBUS modules are to be installed in one of the slots provided in the ATYS p
ATS control unit.
Easy Confi g may be used with a PC connected or through
ETHERNET or MODBUS modules as well as isolated from
the product and simply saved on a PC for download at any
convenient time.
Note: The ATyS p may accept a total of 4 additional Input /
Output modules offering an additional 8 programmable inputs
and 8 programmable outputs. When including a MODBUS
module the ATySp accepts a total of 3 I/O modules and when
including the ETHERNET module a total of 2 I/O modules.
Refer to the ATyS p accessory section for details.
Setup by Auto Confi guration
(Volts, Hz, Neutral pos., Ph rotation)
Press 5s
Go To 1SETUP
Scroll to AUTOCONF
Enter code 1000
Set to YES
Press 60 ms
LEDs fl ash
Save : press 5s
Note: Source I or source II must be
available to set by Auto Confi guration.
ATyS p devices may also be programmed through the ATS controller keypad.
This programming method is necessary for products not equipped with Ethernet
or Modbus communication modules that facilitate programming through
Easy Confi g software described above. The keypad is a useful interface and
programming method most especially when changing a few parameters or
simply interrogating the product.
Programming access: Press and hold for 5 s “Validation” push button (17).
Access through the keypad is possible in Automatic or Manual mode, when the
product is in a stable position (I, 0 or II) with at least one supply source available.
Programming is not accessible whilst any cycle sequence is running.
3 phase / 4 wire 3 phase / 3 wire 2 phase / 3 wire 2 phase / 2 wire 1 phase / 2 wire
4NBL
4BL
1
32
N
3NBL
3BL
1
3
2
2NBL
1
2
3
2BL
1
3
1BL
1
N
17
14
The Ethernet module includes a built in Web Server for
Monitoring, Engine Exerciser Control, Events...
Extended I/O
2xIP 2xO/P
Modbus
RS485
Pulsed O/P 4-20mA
Ethernet/Modbus
TCP Simple
orGateway