SolaX Power X1 Series User manual

IIII
II
Quick Installation Guide
X1 Series 3.0KW-6.0KW
Packing Lists
Inverter Installation
PV Connection
Female DC connector X 2
Male DC connector X 2
AC connector X 1
Quick installation guide ×1
X1 Series 3.0KW-6.0KW
- Unscrew the bracket from the back of the inverter.
- And mark the position(223mm×30mm) of three holes.
- Drill holes with φ10 drill.
- Depth: at least 50mm.
- Screw the expansion screws. - Match the inverter with the bracket.
- Screw the cross recessed screw on the right side.
- make sure available space
Cable size: 12 AWG
trip length:
12 AWG
6.0mm
-Align the four halves connectors.
positive DC
pin contact
male plug
Warranty card × 1 Earth terminal×1
Positive DC pin contact ×2
Negative DC pin contact ×2nut female plug
tight nut
negative DC
pin contact
clamp contact
cable
Inverter
PV array
PV1
PV2
+
-
+
-
+
-
+
-
+
-
Note!
The PV connection
mode as the diagram
shown is not allowed!
×
torque:1.2±0.1Nm torque:1.2±0.1Nm
User manual × 1
X1 Ser ies User Manual
3.0kw - 6.0kw
Copyright Declaration
The copyright of this manual belongs to Solax Power Network Technology(Zhe jiang) Co,. Ltd.
Any corporation or individual should not plagiarize, partitially or fully copy (including software,etc.),
and no reproduction or distribution of it in any form or by any means. All rights reserved. SolaX
Power Network Technology (Zhe jiang) Co.,Ltd. reserves the right of final interpretation.
X1 Series × 1
X1X1
223
30
- Tighten the expansion tubes.
PH1 cross screwdriver, torque:0.8±0.1Nm
torque:0.8±0.1Nm
X1X1
Pocket WiFi × 1(Optional)
X1
Screw package:
Expansion tube X 3
Expansion screw X 3
torque:0.8±0.1Nm
X1X1
300mm
300mm
300mm
300mm
300mm

V
IV
Connections and Overview
Firmware Upgrading
AC Connection
1.Slide the cable nut and
back shell onto the cable.
2.Insert the tripped end of each three
wires into holes in the female insert,
then tighten each screw.
Cable size: 10 AWG
trip length
52.5mm
6mm
55mm
outer jacket
N
L
PE
5.Connect the AC plug to the inverter.
4.Screw down the pressure screw.
3.Screw down the threaded sleeve with pressure screw.
- Screw the ground screw with Φ4 hexagon wrench shown as follow.
- Overview for connection. - After checking all connections are correct, turn on the external
DC /AC breakers.
- Inverter will start automatically when PV panels generate
enough energy. The LED will be blue and the LCD screen
will display the main interface.
- Turn on the DC switch to the “ON” position.
614.00393.04
Firmware Upgrading
torque:3.0±0.3Nm
PH1 cross screwdriver;torque:0.8±0.1Nm
torque:1.5±0.2Nm
5 mm
1) Make sure the DC switch is off
and the AC is disconnected with
grid. Unscrew the waterproof lid
of Upgrade port by straight
screwdriver as the picture shows.
Please contact SolaX service to get the latest firmware. Then add a new folder named
"Update" in the root directory on your U-disk, and two more sub-folders named "ARM" and
"DSP" under "Update". Please copy the firmware files into ARM and DSP respectively. It will be
like:
“update\ARM\618.00207.00_X1_BOOST3.0_MINI2.0_AIR2.0_ARM_V1.10_20190828.usb;
“update\DSP\618.00381.00_X1_BOOST3.0_MINI2.0_AIR2.0_DSP_V1.09_20190613.usb
2) Press and hold the “Enter” key for 5 seconds to enter Off Mode. Then unscrew the
waterproof lid and insert the U-disk into the "upgrade" port.
U-disk
torque:1.5±0.2Nm
Straight screwdriver Waterproof lid
For the inverter with LCD, user can refer to the following:
Ø
3) When the user turns on all the switches, the LCD will show pictures as bellow.
And at the same time, the user can choose the program you need by pressing short
Up and Down , and long press “V” to confirm and upgrade the inverter.
4) After the upgrade is complete, please remember to turn off the DC switch or disconnect the PV
connector, then pull off the U-disk, screw the waterproof lid.
* Please contact our service support to get the update package,and extract it into your U-disk.
Do not modify the program file name ! Or it may cause the inverter not work anymore !
- Prepare the connector and the communication cable, following the PIN
definition and assembly order bellow, then insert the cable into the
corresponding RS485 portof the inverter, and tighten the waterproof connector.
torque:1.2±0.1Nm

1
8
ARM
DSP
Cancel
OK
Update(ARM)
Updating----25%
Update(ARM)
>618.00207.00... ...
ARM
DSP
Update(DSP)
Updating----25%
Update(DSP)
>618.00381.00... ...
PIN
Definition
1 4
Meter_A/
7
E_Stop
5
Meter_B/
8
RefGen
2
Com/DRM0
3
GND_COM
6
CT-
485_A 485_B
CT+
CT/DRM/Meter/RS485
CT
L line
Public grid
→
AC port
arrow point to
the public grid
RS485 port DRM/Meter/RS485