SolaX Power X1 Series User manual

Packing List
BMU Installation
描述
材料
料号
单位 页次
设计
审核
核准
技术要求：
1.材质为80g双胶纸，所有页彩色打印，正反打印
2.未注尺寸公差按 +- 1.5mm
3.图面、字体印刷清晰、无毛边、不起边、油墨不脱落
4.字体颜色为PANTONE Black C，无边框，底色为白色
5.符合RoHS要求
浙江艾罗电源有限公司
罗 西 2016/7/22
朱娴红 2016/7/22
朱娴红 2016/7/22
双胶纸
X1 boost快速安装指南
正反打印,需折叠出货
一折 二折
285 mm
210 mm
REV.REV.
Description Description
0.0
首次发行
罗 西 2016/7/22
描述
料号
单位
614.00140.00
页次
浙江艾罗电源有限公司
SolaX Power Co.,Ltd.
Packing List
X1 boost快速安装指南
614.00140.00
Q-OP-SC-01-02 V1.0
0.0
V1.0删掉PV connection, 增加提醒PV错误电路连接方法。
罗 西 2016/8/19
0.1
删掉开始知道设置里的密码设置
罗 西 2016/11/20

IIII
II
Quick Installation Guide
X1 Series 3.0KW-5.0KW
Packing List
Inverter Installation
PV Connection
X1 Series X 1 Bracket X 1
Screw package:
Expansion tube X 3
Expansion tube X 3
Male DC connector X 2
Female DC connector X 2
AC connector X 1
Note:
Please refer to the appropriate instruction manual for the usage of optional accessories.
User manual X 1
Earth terminal X 1 Quick installation guide X1
X1 Series 3.0KW-5.0KW
Pocket WiFi X 1(Optional) Meter X 1(Optional)
Smart plug X 1(Optional)
- Mark the position of three holes - Drill holes with φ6 drill.
- Depth: at least 50mm.
- Tighten the expansion tubes.
- Screw the expansion screws. - Match the inverter with the bracket.
- Screw the cross recessed screw on the right side.
12 AWG
Cable size: 12 AWG
trip length:
6.0mm
-Align the four halves connectors.
positive DC
pin contact
female plug
Warranty card X 1
Positive DC pin contact ×2
Negative DC pin contact ×2
negative DC
pin contact
clamp contact
nut male plug
tight nut
cable
Inverter
PV array
PV1
PV2
+
-
+
-
+
-
+
-
+
-
Note!
The PV connection
mode in this box
is not allowed!
Waterproof connector with RJ45
X 1
×

V
IV
Earth Connection and Overview
Basic Parameters Setting
AC Connection
1.Slide the cable nut and
back shell onto the cable.
2.Insert the tripped end of each three
wires into holes in the female insert,
then tighten each screw.
Cable size: 10 AWG
trip length
52.5mm
12mm
55mm
outer jacket
N
L
PE
5.Connect the AC plug to the inverter.
4.Screw down the pressure screw.
3.Screw down the threaded sleeve with pressure screw.
- Screw the ground screw with allen wrench shown as follow.
- Overview for connection.
- After checking all connection are correct, turn on the external
DC /AC breakers.
- Inverter will start automatically when PV panels generate
enough energy. The LED will be green and the LCD screen
will display the main interface.
- Turn on the DC switch to the “ON” position.
Country
VDE4105
Safety
English
English
German
French
Name
ESC
Up
Down
Ok
Description
Leave from current interface or function.
Move cursor to upside or increase value.
Move cursor to downside or decrease value.
Conrm the selection.
Symbol
Control Panel
Date time
>2016< -07-07
00:00
Export control
Mode Select
>Disable<
Start Guide
- Select the language
according to the need.
- Set date time based on the
local time.
- The user can set the safety standard here according to different
countries and grid tied standards, please check the following
table* for different standards(May change without notice).
- With this function the inverter can control energy exported to the
grid. Whether having this function is based on user’s wishes.
- Set this parameter based on local grid policy.(For specific country
if required by local grid.)
- The function can be shut off by choosing “disable” mode.
Item
1
2
3
Country
Standard
VDE 4105
IEC 61727
Australia
German
4
AS/NZS 4777.2
Item Country
Standard
Netherland
India
*
EN50438_NL
614.00140.00