SOMFY ROLLIXO io User manual

Rollixo io
Installation manual for rolling doors

2
Rollixo io Contents
Description of the interface for external programming 3
Installation 3
Fixation of the Rollixo receiver 3
Motor connection 3
Safety brake connection 4
Checking and setting the rotation direction 4
1 Checking the rotation direction 4
2 Setting the rotation direction 4
3 Setting the upper end limit 4
4 Setting the lower end limit 5
5 Confirming end limits 5
Connection optical safety edge 5
Connection photocells 6
Connection reflex photocells 6
Alarm 7
Activating/deactivating the alarm 7
Operation of the alarm 7
Testing of the alarm 7
Programming the remote controls 8
Type of remote controls 8
Programming the remote controls 8
Programming the Keygo io remote controls 8
Removing a Keygo io remote control 8
Removing all remote controls 8
Locking/unlocking the programming buttons 9
Locking programming buttons 9
Unlocking programming buttons 9
Dipswitch information 9
Diagnosis 10
Technical details 11

3
Rollixo io
No. Description Function
1 UP button Opens the door
2 STOP button Stops the door
3 DOWN button Closes the door
4 PROG button Programming the remote controls + safety edge transmitter
5 PROG LED Information about radio reception and programming the
transmitters
6 Motor and
safety brake LED
Information about the status of the motor and safety
brake
7 Safety edge LED Information about the status of the safety edge and
safety edge transmitter
8 Battery LED Information about the status of the wireless safety edge
transmitter battery
9 Photocells LED Information about the status of the cells
Description of the interface for external programming
3 421
Prog
STOP
1
2
3
6789
5
4
Fixation of the Rollixo receiver
Installation
Make sure there is a plug socket at a suitable distance (mains cable supplied = 2 m).
We advise installing the receiver on the same side of the door as the safety edge transmitter.
Remove the flush
lighting cover.
Unscrew the receiver
cover and remove it.
Mark the drill holes. Fix the receiver to the
wall.
Motor connection
The receiver may not be connected to the mains supply during the connection of the motor.
L1 L2N
M
1234
Connect the motor to the receiver.
Note: The Rollixo can only control 1 motor and may
not be connected parallel
The motor cable must absolutely
be laid in the receiver’s 230 V insulated
zone.
230 V geïsoleerde zone 24 V geïsoleerde zone
Yellow/green
Brown
Blue
Black
24 V insulated zone230 V insulated zone

4
Rollixo io
Rollixo io
Safety brake connection
If the safety brake is not connected to the Rollixo,
place a shunt between 5 and 6
Sec
Safety EdgeStop
K
56 7891
Checking and setting the rotation direction
3 421
Prog
STOP
3 421
Prog
STOP
3 421
Prog
STOP
3 4
21
Prog
STOP
3 421
Prog
STOP
Go to motor setting mode; at the
same time press the and
buttons until...
Press the UP button ...
Press the STOP key until...
Press the
UP button
Press the
UP button
Product goes
upwards OK
Product goes
upwards OK
Product goes
downwards
NOT OK
go to step 2
Product goes
downwards
NOT OK
step 2 again
...the motor moves to and
fro. LED 1 flashes
slowly.
...the product
goes upwards.
Release at the upper
position. Adjust if necessary
with the and buttons
See the Somfy
manual for
setting the
Somfy motor
See the Simu
manual for
setting the
Simu motor
...the motor moves
to and fro.
or
or
or
1 Checking the rotation direction
2 Setting the rotation direction
3 Setting the upper end limit
See the motor manual for setting the motor.
L1 L2N
M
1234
L1 L2N
M
1234

5
Rollixo io
Rollixo io
3 421
Prog
STOP
Press the UP button ... ...the product
goes downwards.
Release at the lower
position. Adjust if
necessary with the
and buttons
4 Setting the lower end limit
3 421
Prog
STOP
3 421
Prog
STOP
3 421
Prog
STOP
Press the and buttons at the same time and/or the button until... ...the motor moves
to and fro. LED 1
goes out.
or
5 Confirm end limits
Connection optical safety edge
Brown
Brown
Brown
White
White
White
Green
Green
Green
See the Somfy
manual for
setting the
Somfy motor
See the Simu
manual for
setting the
Simu motor
or
L1 L2N
M
1234
L1 L2N
M
1234

6
Rollixo io
Connecting photocells
Connection reflex photocells
1
2
14
15
17
TX
RX
1
2
318
16
519
TX RX
24V dc 24V Cell Sec Cell Test
Sec
h
16 17 18 19 2014 15
Brown
Blue
14
15
Black
Grey
19
20
24Vdc24VCell Sec Cell
Test
Sec
h
16 17 18 19 2014 15
Rollixo ioRollixo io

7
Rollixo io
Alarm
At least one remote control must be programmed. The alarm can only be stopped with a programmed
remote control.
3 421
Prog
STOP
3 421
Prog
STOP
3 421
Prog
STOP
At the same time press the STOP and
button on the receiver until...
Briefly press the STOP and
buttons of the receiver
at the same time.
...4 LEDS start flashing quickly. The alarm sounds a beep if it
is switched on.
The alarm sounds briefly to
show that it is active.
Operation of the alarm
The alarm sounds for 2 minutes if the door is manually lied or in case of obstacle detection cable
sabotage. No movement of the door is possible for as long as the alarm is sounding.
If the alarm sounds, press a button on a programmed remote control in the receiver to stop the alarm.
The alarm can only be stopped with a programmed remote control.
Activating/deactivating the alarm ‘Beep’
‘Beep’
Testing of the alarm
Rollixo io

8
Rollixo io
Programming the remote controls
Types of remote controls
Programming the Keygo io remote controls
Programming from the programming interface
Clearing one Keygo io remote control
To clear a Keygo io from the Rollixo io, the same action must be taken as when programming the
Keygo io remote control
There are two types of remote controls:
n1-way: Keygo io, Situo io, Smoove io, etc.
n2-way with information feedback function
(the remote controls signal the movement and confirm its proper completion):
Keytis io.
3 421
Prog
STOP
3 421
Prog
STOP
3 421
Prog
STOP
Press the button of the
receiver until...
...the LED above it
continuously lights up.
...the LED above the button
flashes, the remote control
is programmed in the receiver.
...LED
flashes.
At the same time
press until...
Within a maximum
of 10 minutes press
a button of the
remote control to be
programmed.
Clearing all remote controls
3 421
Prog
STOP
3 421
Prog
STOP
3 421
Prog
STOP
Press the button of the
receiver until...
...the LED above
the button goes out.
...the LED above
the button starts flashing
slowly.
7 s All programmed
remote controls are
cleared.
Rollixo io

9
Rollixo io
3 421
Prog
STOP
3 421
Prog
STOP
Locking/unlocking the programming buttons
The programming buttons must be locked to guarantee the safety of the users. If the programming
buttons are locked, the following functions cannot be used:
naccess to programming mode by pressing the Prog button of the receiver
naccess to setting mode for the end points of the motor by pressing the buttons and the receiver at the
same time
nsetting the work modes.
Lock programming buttons
Unlock programming buttons
To unlock the programming buttons, repeat the abovementioned locking procedure.
At the same time press the STOP and
Prog button of the receiver until...
...all LEDS flash. The programming buttons are
now locked.
Dipswitch information
Dipswitch Possible setting ON OFF
1 Self-test photocells Activated Deactivated
2 Choice of cell type Photoelectric Reflection
3 2 s warning indication light Activated Deactivated
4 Selection of type of wired protection Resistance Optical
5 Setting holiday mode See standard installation manual
part 9.4
6 Do not use
3 421
Prog
STOP
Rollixo io

10
Rollixo io
Diagnosis
Safety
brake
Diagnosis Safety brake not connected or no connection to the connector between 5 and 6. Safety brake
activated (when connected between 5 and 6)
Consequences No movement at all possible
Actions Check the safety brake connection
Motor
Diagnosis Motor not properly connected
Consequences No movement at all possible
Actions Check the motor connection
Diagnosis Safety brake activated (if safety brake is connected between the blue wire of the motor)
Consequences No movement at all possible
Actions Check the installation and replace the safety brake
Diagnosis Thermal motor protection switched on
Consequences No movement at all possible
Actions Wait approximately 10 minutes
Diagnosis Motor defective or fuse blown
Consequences No movement at all possible and flush lighting not on
Actions Check the condition of the fusing and replace if required (spare fuse supplied). Replace the
motor if it is still not working
Motor Diagnosis Waiting for motor adjustment
Actions Adjust the motor end points
Status of the LED Meaning
LED is off Installation working
LED flashes slowly Waiting for an action or setting
LED flashes quickly Detection/activation working
LED stays on Failure/defect in the installation
Rollixo io