SOMFY inteo LIGHTING indoor RTS User manual

inteo LIGHTING indoor RTS
INSTALLATION guide
Ref.5004240
■Main supply : 220-240V ~
■ Fuse : 3,15A
■Class II product
■Protection index : IP30
■Load : incandescent or halogen
lamps 500 W max.
■Radio frequency : 433.42 MHz
■Operating temp. : +5°C to +40°C
1
Characteristics
2
Installation
Recommandation of mounting for better radio
reception :
minimum distance between LIGHTING indoor RTS
and the floor : 1,5 m.
minimum distance between a LIGHTING indoor
RTS and a radio transmitter : 30 cm.
minimum distance between two LIGHTING indoor
RTS : 20 cm.
Warning : cordless radio equipment (e.g.
headphones) in 433MHz can affect the fun-
ctionning of the LIGHTING indoor RTS.
The LIGHTING indoor RTS is a radio receiver dedicated to control an incandescent or
halogen lamp with an RT or RTS control (no lamp with gear).
Up to twelve different controls can be memorized in the memory of the LIGHTING
indoor RTS allowing individual, group and master commands.
This device must be installed and programmed by qualified installers for whom
this instruction is intended.
3
Programming and operating
3.1 Record the first control
R
PROG
▲,S,▼,S
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the batte-
ry and press again briefly the button.
➜The lamp lights during 2 secs. again and the LED of the LIGHTING
indoor RTS blinks during 5 sec. The control has been recorded.
Set the LIGHTING indoor RTS in its programming mode : Record the first control :
80 mm
80 mm
45 mm
fuse
programming
button
manual
control button
LED
Neutral
POWER
SUPPLY
Phase
LN
Phase
Neutral
Output
Do not use
N
X
L
2 s
➜
Press for more than 2 seconds on the programming button of
the LIGHTING indoor RTS.
➜The LED of the LIGHTING indoor RTS lights on and the
lamp lights for 2 secs.
The LIGHTING indoor RTS is in programming mode for one
minute.
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
➜
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
0,5 s
0,5 s 0,5 s
or
5 s
2 s
2 s
12
ø 60
60
Recessed mounting :
Surface mounting :
Hereby, SOMFY,declares that this equipment is in com-
pliance with the essential requirements and other rele-
vant provisions of Directive 1999/5/EC.
A Declaration of Conformity is available at the web
address www.somfy.com Heading CE

R
PROG
▲,S,▼,S
3.4 Remove a control
3.5 Complete reset (back to factory configuration)
3.3 Record a new control
3.2 Operating
Note : When you enter in programming mode with an already recorded control, you cannot erase it
or
With a RTS control With a RT control With the built in control button
Press briefly the ▲button to switch the lamp ON.
Press briefly the ■or ▼ buttons to switch the lamp OFF.
ON OFF ON/OFF
Press briefly on the front button of the RT
control to switch the lamp ON or OFF. You can also control the lamp with the push button located on the LIGHTING indoor RTS.
4
Trouble shooting guide
Nothing works:
ðCheck the light.
ðCheck the power supply.
ðCheck the battery of the transmitter.
ðCheck that the transmitter has been properly recorded in the LIGHTING indoor RTS memory (section 3).
ðCheck for any other possible source of radio interferences.
Lost in your programming mode:
ðJust make a complete reset and start again.
Press for more than 2 sec. on the programming button of the LIGHTING indoor RTS
or use an already recorded control.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜The LED of the LIGHTING indoor RTS lights on and the lamp lights for 2 secs.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜The lamp lights during 2 secs. again and the LED of the LIGHTING
indoor RTS blinks during 5 sec. The new control is recorded.
RTS control : press briefly the “prog” button.
RT control : remove the battery, press briefly the button, replace the
battery and press again briefly the button.
➜The lamp lights during 2 secs. again and the LED of the LIGHTING
indoor RTS blinks during 5 sec. The control has been erased.
1 2
1 2
Set the LIGHTING indoor RTS in its programming mode : Record the new control :
Remove the control :
➜
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
➜
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
2 s
0,5 s 0,5 s 0,5 s
or or
2 s 2 s
➜
Press for more than 7 seconds the programming button of the LIGHTING indoor RTS until the
LED lights.
➜The LED lights up after 2 seconds and blinks after 7 seconds Then, the lamp lights during 2 secs.
the LIGHTING indoor RTS has been completely cleared and no more controls are recorded.
You have then to re-program the LIGHTING indoor RTS from the first step of programming
(refer to the section 3.1 “Record the first control”).
2 s
already recorded control
or
Press for more than 2 sec. on the programming button of the LIGHTING indoor RTS
or use an already recorded control.
RTS control : press for more than 2 sec. on the “prog” button.
RT control : remove the battery, press briefly the button, replace the battery and
press for more than 2 sec. on the button.
➜The LED of the LIGHTING indoor RTS lights on and the lamp lights for 2 secs.
Set the LIGHTING indoor RTS in its programming mode :
5 s
2 s
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
3V
LITHIUM
RENATA
CR 2430
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2430
R
PROG
▲,S,▼,S
➜
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
0,5 s 0,5 s
or
2 s
5 s
ON/OFF
2 s
➜
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR2032
3V
LITHIUM
RENATA
CR2032
S
W
I
S
S
M
A
D
E
2 s
0,5 s
or
2 s
2 s
already recorded control
or
R
PROG
▲,S,▼,S
R
PROG
▲,S,▼,S
2 s
7 s
0,5 s
3V
LITHIUM
RENATA
CR 2430
S
W
I
S
S
M
A
D
E
3V
LITHIUM
RENATA
CR 2430
0,5 s
5 s
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
All rights reserved to makes changes without prior notice.