SonoSite iViz User manual

Quick Reference Guide
SonoSite iViz Ultrasound System
Quick Reference Guide
SonoSite iViz Ultrasound System
Overview
This Quick Reference Guide is for reference and refresh only and is not intended
as a substitute for the user guide that came with your SonoSite iViz system. For
detailed procedures, descriptions, features, and safety precautions, see the
SonoSite iViz User Guide, available at www.sonosite.com.
Overview
This Quick Reference Guide is for reference and refresh only and is not intended
as a substitute for the user guide that came with your SonoSite iViz system. For
detailed procedures, descriptions, features, and safety precautions, see the
SonoSite iViz User Guide, available at www.sonosite.com.
Front of the iViz system
Overview
Touchscreen while in Scan mode
Volume up
Volume down
Transducer socket
Audio out
Micro HDMI port
Micro USB port
Front camera
Power on/off
Power status LED
Microphone
Changes
Scan mode
(press and
hold)
2D
C
COLOR
FREEZE SAVE
Orient
Dynamic
Range
Opt
End Study
Patient: John Smith ID: 1234567890 P21v: Abdomen
MI:
0.0
TI:
0.0
DR:
0
PEN
MHz
0.00
89%
13%
9:15
7/18/2018
Depth: 16.4cm
Slides through
the options on
the control
wheel
Freezes
an image
Captures
an image
or clip
Shows number of
saved images and
clips
Displays patient
information
Lets you
select exam
type
Shows power
management
Displays
time, date,
and percent
charged
Ends study and
returns you to the
patient record
Displays
Android
controls
Shows
scan
area
Opens tool
drawer
Page 1 of 10
P22705-01
Page 2 of 10
P22705-01

Quick Reference Guide
SonoSite iViz Ultrasound System
Quick Reference Guide
SonoSite iViz Ultrasound System
Before scanning
Installing the battery
1On the back of the system, position the battery in the battery slot so that the
beveled edge of the battery is nearest the side of the SonoSite iViz system.
2Press the battery firmly into the back of the system until it locks in place.
Checking the battery bay charger
Connecting transducers
Insert the transducer connector into the bottom of the system, with the
transducer cable facing away from the other connectors.
Before scanning
Using gestures
Swipe
Move your finger quickly across the screen.
Drag
Move one or two fingers across the screen, usually to move an object from one
location to another.
Tap
Quickly touch the screen once.
Press and hold
Touch your finger to the screen, and hold it there for about two seconds.
Pinch or zoom
Slide two fingers together or apart on the screen.
Turning on the system
1Check that a battery is installed.
2Press the Power button, and wait several seconds for the system to power
on.
3Swipe up on the Lock icon.
Choosing an exam type
1When scanning, tap the Exam Type drop-down menu in the upper right of
the screen. A list of available exam types appears.
2Tap the exam type you want to change to.
LED Behavior Condition
Blinking green Battery is charging.
Green Battery is fully charged.
Amber/light red Battery is very low.
Red Bad battery pack; recycle the battery.
Page 3 of 10
P22705-01
Page 4 of 10
P22705-01

Quick Reference Guide
SonoSite iViz Ultrasound System
Quick Reference Guide
SonoSite iViz Ultrasound System
Scanning
Imaging modes
To switch from 2D to M Mode, press and hold 2D; press and hold Mto return
to 2D.
2D (default) – This mode displays echoes in two dimensions by assigning a
brightness level based on the echo signal amplitude.
M Mode (Motion Mode) – This mode provides a trace of the image displayed
over time. A single beam of ultrasound is transmitted, and reflected signals
are displayed as dots of varying intensities, which create lines across the
screen.
Color – This mode is used to visualize the presence, velocity, and direction of
blood flow in a wide range of flow states. To go to Color mode, tap Color on
the wheel while in 2D.
Performing a basic scan
In SonoSite iViz, the active imaging mode is always highlighted in blue so you
can tell what imaging mode you are using. For example, in Color mode, both
the 2D and Color buttons are highlighted in blue.
Adjusting gain and depth
To adjust gain, on the control wheel, tap Overall Gain or Near/Far Gain, and
move the blue dot up and down the slider.
To adjust depth, on the control wheel, tap Depth, and use the plus/minus
buttons to increase/decrease scan depth (or tap one of the dots for specific
screen-depth index).
Freezing and scrolling frames (cine)
1While scanning, tap FREEZE.
2View frames by dragging the green slider up and down to scroll through the
frames, or select the back arrow to return to the first frame or the forward
arrow to go to the last frame.
Scanning
Adding labels
1Do one of the following:
aOn a frozen image, tap Tex t Labels.
bOn a saved image, open the bottom tool drawer by swiping upward on
the tool drawer handle in the lower right of the screen, then tap Text
Labels.
2To add an arrow:
aTap +Arrow.
bUsing your finger, drag the arrow to a location on the screen.
cUsing your finger, drag the blue orientation arrows to rotate the center
black arrow.
3To add a standard label:
aTap the label you want to add, such as Right or Medial.
bUsing your finger, drag the label to a location on the screen.
4To add a custom label to this image:
aTap the text box at the top of the list of labels.
bType the text of the label, and then tap Done.
cUsing your finger, drag the label to a location on the screen.
Refer to the iViz User Guide for more information about creating and saving
Custom Labels.
Page 5 of 10
P22705-01
Page 6 of 10
P22705-01

Quick Reference Guide
SonoSite iViz Ultrasound System
Quick Reference Guide
SonoSite iViz Ultrasound System
Scanning
Sharing a study
1From the Patient module, tap the iViz Studies tab.
2Tap Study. This exports the reports, images and clips within a study.
3Tap .
4Tap one or more of the following check boxes:
Local PACS - Use this option to send a study through DICOM. If you select
this option, you will be asked to choose a server from the list.
Tricefy - Use the Tricefy medical image-sharing tool to share a study,
image, or clip. To use this option, you must have an active Tricefy account.
USB - Use this option to save the study to the USB drive inserted in the
system.
5Tap Next. Depending on the option you choose, complete the remaining
information on the right side of the screen (for example, the local PACS
server).
6Tap Share.
Creating or updating a patient study
1To open the Patient module:
From the Home screen tap Patient.
During an exam, tap the Patient field at the top of the screen.
2Do one of the following:
To update a patient study, locate and open the study you want to
change.
In an open patient study, in the Patient module, tap New Study.
3Enter or change the patient information.
4Tap Save.
Measuring
Measuring distance
1On a frozen scan, tap Measurements.
2Under the General measurements area, tap Distance.
3Drag the active caliper to the first point, then drag the other caliper to the
second point.
4As needed, tap and drag each caliper until it is precisely positioned.
Measuring an ellipse
1On a frozen scan, tap Measurements.
2Under the General measurements area, tap Ellipse.
3Drag the caliper to the boundary of the feature you want to measure. When
you lift your finger, a dashed circle appears, and the ellipse is anchored at
that point.
4Drag the second caliper along the horizontal axis to align it to the rest of the
feature you are measuring.
5Tap the height caliper to make it active.
6Drag the height caliper to the height of the feature you want to measure. The
diameter, area, and circumference measurements appear in the
Measurements box.
Page 7 of 10
P22705-01
Page 8 of 10
P22705-01

Quick Reference Guide
SonoSite iViz Ultrasound System
Quick Reference Guide
SonoSite iViz Ultrasound System
Measuring
Measuring a shape
1On a frozen scan, tap Measurements.
2Under the General measurements area, tap Trace. An active caliper appears
on the screen.
3Drag the caliper to the start point of your measurement, and lift your finger.
4Drag the caliper to outline the feature you want to measure. A dotted line
shows the path of the trace.
5Before you lift your finger, make sure the ends of the trace are close together;
that way, the trace automatically closes. The area and circumference
measurements appear in the Measurements box.
Measuring heart rate
1From the Exam Type drop-down menu, tap Cardiac.
2On a frozen M-Mode trace, tap Measurements.
3Switch to the Cardiac calculation list.
4Under HR, tap HR in the calculations list.
5Position the caliper at the peak of a heartbeat, and lift your finger from the
screen. A second caliper appears.
6Position the second caliper at the peak of the next heartbeat, and lift your
finger from the screen. The heart rate appears.
Contact information
Phone (U.S. or Canada): 877-657-8118
Phone (Outside U.S. or Canada): 425-951-1330, or call your local representative
Fax: [phone]
E-mail: [email protected]
Web: www.sonosite.com
iViz, SonoSite, and the SonoSite logo are trademarksor registered trademarks of FUJIFILM SonoSite,
Inc. in various jurisdictions. FUJIFILM is a trademark and registered trademark of FUJIFILM
Corporation in various jurisdictions.
All other trademarks are the property of their respective owners.
Copyright ©2017 FUJIFILM SonoSite, Inc. All rights reserved.
P22705-01
*P22705-01*
Manufacturer
FUJIFILM SonoSite, Inc.
21919 30th Drive SE
Bothell, WA 98021 USA
T: 1-888-482-9449 or
1-425-951-1200
F: 1-425-951-1201
EC Authorized
Representative
Emergo Europe
Molenstraat 15
2513 BH, The Hague
The Netherlands
Australia Sponsor
FUJIFILM SonoSite
Australasia Pty Ltd
114 Old Pittwater Road
BROOKVALE, NSW, 2100
Australia
Page 9 of 10
P22705-01
Page 10 of 10
P22705-01