Sony NEX-FS100C User manual

SERVICE MANUAL
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
SERVICE NOTE (Check the following note before the service.)
Revision History
Published by Sony Techno Create Corporation
Sony Corporation
983458812.pdf
Ver. 1.1 2012.05
INTERCHANGEABLE LENS DIGITAL HD VIDEO CAMERA RECORDER
The components identified by mark
0or dotted line with mark 0are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
9-834-588-12
US Model
Canadian Model
AEP Model
E Model
Chinese Model
Japanese Model
Ver. Date History Contents S.M. Rev.
issued
1.0 2011.05 Official Release — —
1.1 2012.05 Revised-1
(A1 12-050)
• Addition of SERVICE NOTE.
Page 1-1, 1-2, 1-3, 1-4
･Correction of EXPLODED VIEWS.
Page 2-6, 2-8, 2-9, 2-11, 2-18, 2-19
･Correction of ACCESSORIES.
Page 2-20
･Correction of ELECTRICAL PARTS LIST.
Page 2-24
Yes
2012E08-1
© 2012.05
– ENGLISH –
1-1. POWER SUPPLY DURING REPAIRS
1-2. PRECAUTION ON REPLACING THE VC-618 BOARD
1-3. SELF-DIAGNOSIS FUNCTION
1-4. METHOD OF COPING WITH LENS ERROR
‒JAPANESE‒
1-1. 修理時の電源供給について
1-2. VC-618基板交換時の注意
1-3. 自己診断機能
1-4. レンズエラーの対処方法
[About the service of this model]
NEX-FS100CK/FS100EK/FS100JK/FS100NK/FS100PK/FS100UK is a commodity that packed the Interchangeable Lens
Digital HD Video Camera Recorder (NEX-FS100C/FS100E/FS100J/FS100N/FS100P/FS100U) and InterchangeableLens (E
18-200mm F3.5-6.3 OSS).
Refer to each following service manual of the Interchangeable Lens kit, when you repair.
･Interchangeable Lens
SEL18200 (E 18-200mm F3.5-6.3 OSS) Service Manual (9-834-507-1[])
Photo: NEX-FS100UK
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/
FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
Revised-1
Replace the previously issued
SERVICE MANUAL 9-834-588-11
with this Manual.

– 2 –
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
SPECIFICATIONS
System
Video signal
PAL color, CCIR standards
HDTV 1080/50i, 1080/50p, 720/50p
specification
Video recording system
HD image quality: MPEG-4 AVC/
H.264 AVCHD format compatible
(1080/50p: original format)
SD image quality: MPEG-2 PS
Audio recording system
Linear PCM 2ch (48 kHz 16-bit)
Dolby Digital 2ch (48 kHz 16-bit)
Dolby Digital Stereo Creator employed
Still image recording system
DCF Ver. 2.0 Compatible
Exif Ver. 2.3 Compatible
MPF Baseline Compatible
Recording media (movies/still images)
“Memory Stick PRO Duo” media
Flash memory units
SD card (Class 4 or faster)
Image device
“Exmor” Super35 CMOS sensor
23.6 mm × 13.3 mm (Ø 27.1 mm)
Gross: Approx. 3 530 000 pixels
Effective (movie, 16:9):
Approx. 3 370 000 pixels
Effective (movie, 4:3):
Approx. 2 530 000 pixels
Color temperature
[AUTO]
(one push) A/B
[INDOOR] (3 200K)
[OUTDOOR] (5 800K)
Minimum illumination
1.5 lx (lux) with Shutter Speed 1/25,
auto gain control, auto iris (using the E
18-200 mm F3.5-6.3 OSS lens*)
* Supplied with NEX-FS100EK/FS100PK
Input/output connectors
VIDEO OUT jack
Pin connector
Video output
1 Vp-p, 75 Ω(ohms) unbalanced, sync
negative
AUDIO OUT jacks
Pin connectors
-10 dBu (at load impedance 47 kΩ
(kilohms)), Output impedance with less
than 2.2 kΩ(kilohms)
(0 dBu = 0.775 Vrms)
COMPONENT OUT jack
Mini-D jack
Y: 1 Vp-p, 75 Ω(ohms)
P
B/PR, CB/CR: 0.7 Vp-p, 75 Ω(ohms)
REMOTE jack
Stereo mini-minijack (Ø 2.5 mm)
HDMI OUT jack
HDMI Connector (Type A)
USB jack
mini-AB
i(headphones) jack
Stereo minijack (Ø 3.5 mm)
INPUT1/INPUT2 jacks
XLR 3-pin, female,
MIC: -48 dBu/3 kΩ(kilohms)
LINE: +4 dBu/10 kΩ(kilohms)
(0 dBu = 0.775 Vrms)
LCD screen
Picture
8.8 cm (3.5 type, aspect ratio 16:9)
Total dot number
921 600 (1 920 × 480)
General
Power requirements
DC 7.2 V (battery pack)
DC 8.4 V (AC Adaptor/Charger)
Average power consumption
During camera recording using the
microphone ECM-XM1, LCD with
normal brightness (using the E 18-200
mm F3.5-6.3 OSS lens*)
5.6 W
When Flash Memory Unit HXRFMU128
is used, the average power
consumption increases about 1.1 W.
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to +60 °C (-4 °F to +140 °F)
Dimensions (approx.)
Camcorder body only (including the
projecting parts):
126.5 mm × 101.5 mm × 193.5 mm
(5 in. × 4 in. × 7 5/8 in.) (w/h/d)
When recording (including the
projecting parts):
178 mm × 192 mm × 519.5 mm
(7 1/8 in. × 7 5/8 in. × 20 1/2 in.) (w/h/
d) (With the accessories (lens*, lens
hood*, large LCD viewfinder, large
eyecup, handle, microphone (ECMXM1),
and grip (without the belt)
attached.)
Mass (approx.)
Camcorder body only:
1 040 g (2 lb 4 oz)
When recording:
2 660 g (5 lb 13 oz) (With the
accessories (battery pack (NP-F770),
lens*, lens hood*, large LCD
viewfinder, large eyecup, handle,
microphone (ECM-XM1), grip, and
flash memory unit cover attached.)
* Supplied with NEX-FS100EK/FS100PK
AC Adaptor/Charger AC-VL1
Power requirements
AC 100 V - 240 V, 50 Hz/60 Hz
Power consumption
22 W
Output voltage
DC 8.4 V*
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to +60 °C (-4 °F to +140 °F)
Dimensions (approx.)
136 mm × 51 mm × 90 mm
(5 3/8 in. × 2 1/8 in. × 3 5/8 in.) (w/h/d)
excluding the projecting parts
Mass (approx.)
270 g (9.6 oz) excluding the power cord
(mains lead)
* See the label on the AC Adaptor/Charger for
other specifications.
Rechargeable battery pack NP-F770
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Maximum charge voltage
DC 8.4 V
Maximum charge current
3.0 A
Capacity
Typical: 31.7 Wh (4 400 mAh)
Minimum: 30.0 Wh (4 200 mAh)
Type
Li-ion
E 18-200 mm F3.5-6.3 OSS lens
(Supplied with NEX-FS100EK/
FS100PK)
Lens
E-mount lens
When converted to a 35 mm still camera
28.8 mm - 320 mm (1 3/16 in. -
12 5/8 in.) (16:9)
36 mm - 400 mm (1 7/16 in. -
15 3/4 in.) (4:3)
F-value
F3.5-F6.3
SteadyShot
Optical-shift biaxial-linear-drive and
hall effect sensor
Minimum focus*
0.30 m (W) - 0.50 m (T) (11 7/8 in. -
19 3/4 in.)
Maximum magnification
×0.35
Minimum f-stop
f/22 - f/40
Filter diameter
67 mm (2 3/4 in.)
Dimensions (approx. max. diameter ×
height)
75.5 mm × 99.0 mm (3 in. × 4 in.)
Mass (approx.)
524 g (18 1/2 oz.)
* Minimum focus is the shortest distance from the
image sensor to the subject.
Design and specifications are subject to change
without notice.
• Manufactured under license from Dolby
Laboratories.
– ENGLISH –
These specifications are extracted from instruction manual of
NEX-FS100E/FS100P/FS100EK/FS100PK.
These specifications are extracted from instruction manual of
NEX-FS100U/FS100N/FS100UK/FS100NK.
SPECIFICATIONS
System
Video signal
NTSC color, EIA standards
HDTV 1080/60i, 1080/60p, 720/60p
specification
Video recording system
HD image quality: MPEG-4 AVC/
H.264 AVCHD format compatible
(1080/60p: original format)
SD image quality: MPEG-2 PS
Audio recording system
Linear PCM 2ch (48 kHz 16-bit)
Dolby Digital 2ch (48 kHz 16-bit)
Dolby Digital Stereo Creator employed
Still image recording system
DCF Ver. 2.0 Compatible
Exif Ver. 2.3 Compatible
MPF Baseline Compatible
Recording media (movies/still images)
“Memory Stick PRO Duo” media
Flash memory units
SD card (Class 4 or faster)
Image device
“Exmor” Super35 CMOS sensor
23.6 mm × 13.3 mm (Ø 27.1 mm)
Gross: Approx. 3 530 000 pixels
Effective (movie, 16:9):
Approx. 3 370 000 pixels
Effective (movie, 4:3):
Approx. 2 530 000 pixels
Color temperature
[AUTO]
(one push) A/B
[INDOOR] (3 200K)
[OUTDOOR] (5 800K)
Minimum illumination
1.2 lx (lux) with Shutter Speed 1/24,
1.5 lx (lux) with Shutter Speed 1/30,
auto gain control, auto iris (using the E
18-200 mm F3.5-6.3 OSS lens*)
* Supplied with NEX-FS100UK/FS100NK
Input/output connectors
VIDEO OUT jack
Pin connector
Video output
1 Vp-p, 75 Ω(ohms) unbalanced, sync
negative
AUDIO OUT jacks
Pin connectors
-10 dBu (at load impedance 47 kΩ
(kilohms)), Output impedance with less
than 2.2 kΩ(kilohms)
(0 dBu = 0.775 Vrms)
COMPONENT OUT jack
Mini-D jack
Y: 1 Vp-p, 75 Ω(ohms)
P
B/PR, CB/CR: 0.7 Vp-p, 75 Ω(ohms)
REMOTE jack
Stereo mini-minijack (Ø 2.5 mm)
HDMI OUT jack
HDMI Connector (Type A)
USB jack
mini-AB
i(headphones) jack
Stereo minijack (Ø 3.5 mm)
INPUT1/INPUT2 jacks
XLR 3-pin, female,
MIC: -48 dBu/3 kΩ(kilohms)
LINE: +4 dBu/10 kΩ(kilohms)
(0 dBu = 0.775 Vrms)
LCD screen
Picture
8.8 cm (3.5 type, aspect ratio 16:9)
Total dot number
921 600 (1 920 × 480)
General
Power requirements
DC 7.2 V (battery pack)
DC 8.4 V (AC Adaptor/Charger)
Average power consumption
During camera recording using the
microphone ECM-XM1, LCD with
normal brightness (using the E 18-200
mm F3.5-6.3 OSS lens*)
5.6 W
When Flash Memory Unit HXRFMU128
is used, the average power
consumption increases about 1.1 W.
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to +60 °C (-4 °F to +140 °F)
Dimensions (approx.)
Camcorder body only (including the
projecting parts):
126.5 mm × 101.5 mm × 193.5 mm
(5 in. × 4 in. × 7 5/8 in.) (w/h/d)
When recording (including the
projecting parts):
178 mm × 192 mm × 519.5 mm
(7 1/8 in. × 7 5/8 in. × 20 1/2 in.) (w/h/
d) (With the accessories (lens*, lens
hood*, large LCD viewfinder, large
eyecup, handle, microphone (ECMXM1),
and grip (without the belt)
attached.)
Mass (approx.)
Camcorder body only:
1 040 g (2 lb 4 oz)
When recording:
2 660 g (5 lb 13 oz) (With the
accessories (battery pack (NP-F770),
lens*, lens hood*, large LCD
viewfinder, large eyecup, handle,
microphone (ECM-XM1), grip, and
flash memory unit cover attached.)
* Supplied with NEX-FS100UK/FS100NK
AC Adaptor/Charger AC-VL1
Power requirements
AC 100 V - 240 V, 50 Hz/60 Hz
Power consumption
22 W
Output voltage
DC 8.4 V*
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to +60 °C (-4 °F to +140 °F)
Dimensions (approx.)
136 × 51 × 90 mm
(5 3/8 × 2 1/8 × 3 5/8 in.) (w/h/d)
excluding the projecting parts
Mass (approx.)
270 g (9.6 oz) excluding the power cord
(mains lead)
* See the label on the AC Adaptor/Charger for
other specifications.
Rechargeable battery pack NP-F770
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Maximum charge voltage
DC 8.4 V
Maximum charge current
3.0 A
Capacity
Typical: 31.7 Wh (4 400 mAh)
Minimum: 30.0 Wh (4 200 mAh)
Type
Li-ion
E 18-200 mm F3.5-6.3 OSS lens
(Supplied with NEX-FS100UK/
FS100NK)
Lens
E-mount lens
When converted to a 35 mm still camera
28.8 mm - 320 mm (1 3/16 in. -
12 5/8 in.) (16:9)
36 mm - 400 mm (1 7/16 in. -
15 3/4 in.) (4:3)
F-value
F3.5-F6.3
SteadyShot
Optical-shift biaxial-linear-drive and
hall effect sensor
Minimum focus*
0.30 m (W) - 0.50 m (T) (11 7/8 in. -
19 3/4 in.)
Maximum magnification
×0.35
Minimum f-stop
f/22 - f/40
Filter diameter
67 mm (2 3/4 in.)
Dimensions (approx. max. diameter ×
height)
75.5 mm × 99.0 mm (3 in. × 4 in.)
Mass (approx.)
524 g (18 1/2 oz.)
* Minimum focus is the shortest distance from the
image sensor to the subject.
Design and specifications are subject to change
without notice.
• Manufactured under license from Dolby
Laboratories.
– ENGLISH –

– 3 –
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
概略仕様
システム
信号方式
NTSCカラー、EIA標準方式
HDTV 1080/60i、1080/60p、
720/60p方式
ビデオ記録方式
HD画質：MPEG-4 AVC/H.264
AVCHD規格準拠（1080/60p:独
自規格）
SD画質：MPEG-2 PS
音声記録方式
リニアPCM 2ch（48kHz 16bit）
Dolby Digital 2ch（48kHz
16bit）
ドルビーデジタルステレオクリ
エーター搭載
静止画ファイルフォーマット
DCF Ver.2.0準拠
Exif Ver.2.3準拠
MPF Baseline準拠
記録メディア（動画・静止画）
メモリースティック PRO デュ
オ
フラッシュメモリーユニット
SDカード（Class 4以上）
撮像素子
ExmorSuper35 CMOSセン
サー
23.6mm×13.3mm (対角
27.1mm）
総画素数：約353万画素
動画時有効画素数（16：9モー
ド）：約337万画素
動画時有効画素数（4：3モード）：
約253万画素
色温度切り換え
オート
ワンプッシュ（A, B）
屋内（3 200K）
屋外（5 800K）
最低被写体照度
1.5 lx（ルクス）
シャッタースピード固定（1/30）
オートゲインコントロール、アイ
リスオート（E 18-200 mm F3.5-
6.3 OSS*使用時）
* NEX-FS100JK に付属
入/出力端子
VIDEO OUT端子
ピンジャック
1Vp-p、75Ω不平衡、同期負
AUDIO OUT端子
ピンジャック
-10dBu（47kΩ負荷時）、
出力インピーダンス2.2kΩ以下
（0dBu=0.775Vrms）
COMPONENT OUT端子
ミニD端子
Y：1Vp-p、75Ω
P
B/PR. CB/CR：0.7Vp-p、75Ω
リモート端子
ステレオミニミニジャック
（Φ2.5mm）
HDMI OUT端子
HDMIコネクター（タイプA）
USB端子
mini-AB
i
（ヘッドホン）端子
ステレオミニジャック
（Φ3.5mm）
INPUT1/INPUT2端子
XLR型3ピン×2、凹
MIC：-48dBu：3kΩ
LINE：+4dBu：10kΩ
（0dBu=0.775Vrms）
液晶画面
画面サイズ
8.8cm（3.5型、アスペクト比
16:9）
総ドット数
921 600ドット
横1 920×縦480
電源部、その他
電源電圧
DC7.2V（バッテリーパック使用時）
DC8.4V（ACアダプター /チャー
ジャー使用時）
消費電力
マイク（ECM-XM1）、液晶画面使
用時、明るさ標準、E 18-200 mm
F3.5-6.3 OSS*使用時：
5.6W
フラッシュメモリーユニット
HXR-FMU128使用時は、消費電
力が約1.1W増えます。
動作温度
0℃〜 40℃
保存温度
−20℃〜 +60℃
本体外形寸法（突起部含む）
約126.5mm×101.5mm×
193.5mm（幅×高さ×奥行き）
撮影時外形寸法（突起部含む）
約178mm×192mm×
519.5mm（幅×高さ×奥行き）
（レンズ*、レンズフード*、ビュー
ファインダー、大型アイカップ、
ハンドル、マイク（ECM-XM1）、
グリップ（ベルト無し）含む）
本体質量約
1 040g
撮影時総質量
約2 660g
（バッテリーパック（NP-F770）、
レンズ*、レンズフード*、ビュー
ファインダー、大型アイカップ、
ハンドル、マイク（ECM-XM1）、
グリップ（ベルト無し）含む）
* NEX-FS100JK に付属
E18-200mmF3.5-6.3OSS
（NEX-FS100JKに付属）
レンズ
Eマウントレンズ
35mmカメラ換算
動画撮影時（16:9）：28.8mm -
320mm
動画撮影時（4:3）：36mm -
400mm
F値
F3.5-F6.3
手ブレ補正
光学シフト2実リニア駆動＋ホー
ル素子
最短撮影距離*
0.30m (W) - 0.50m (T)
最大撮影倍率
0.35倍
最小絞り
f/22 - f/40
フィルター径
67mm
外形寸法（最大径×長さ）
約75.5mm×99.0mm
質量
約524ｇ
* 最短撮影距離とは、イメージセンター面から被写体
までの最短距離を表します。
本機の仕様および外観は、改良のため予告なく変
更することがありますが、ご了承ください。
• ドルビーラボラトリーズからの実施権に基づき製造
されています。
Model information table
Model FS100C FS100CK FS100E FS100EK FS100J FS100JK
Destination CH CH AEP AEP J J
Color system PAL PAL PAL PAL NTSC NTSC
Lens E 18-200 mm
F3.5-6.3 OSS
E 18-200 mm
F3.5-6.3 OSS
E 18-200 mm
F3.5-6.3 OSS
Model FS100N FS100NK FS100P FS100PK FS100U FS100UK
Destination EEEEUS, CND US, CND
Color system NTSC NTSC PAL PAL NTSC NTSC
Lens E 18-200 mm
F3.5-6.3 OSS
E 18-200 mm
F3.5-6.3 OSS
E 18-200 mm
F3.5-6.3 OSS
･Abbreviation
CH : Chinese model
CND : Canadian model
J : Japanese model
– JAPANESE –

– 4 –
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は，正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は，取扱指示に従って処分してください。
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
1. 注意事項をお守りください。
 サービスのとき特に注意を要する個所については，キャビ
ネット，シャーシ，部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2. 指定部品のご使用を
 セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は，使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図，部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3. 部品の取付けや配線の引きまわしはもとどおりに
 安全上，チューブやテープなどの絶縁材料を使用したり，
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので，これらは必
ずもとどおりにして下さい。
4. サービス後は安全点検を
 サービスのために取外したネジ，部品，配線がもとどおり
になっているか，またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し，安全性が確保さ
れていることを確認して下さい。
5. チップ部品交換時の注意
 ・取外した部品は再使用しないで下さい。
 ・タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6. フレキシブルプリント基板の取扱いについて
 ・半田こてのこて先温度は約350℃に設定してください。
 ・同一パターンに何度もコテ先を当てないで下さい。（3回
以内）
 ・パターンに力が加わらないよう注意して下さい。
サービス，点検時には次のことにご注意ください。
– ENGLISH – – JAPANESE –
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には，無鉛（LeadFree）を意味する
レッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す）
：レッドフリーマーク
無鉛半田は，下記の点に注意して使用してください。
・ 半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は，高温短時間で作業を行ってくだ
さい。
注意：半田こてを長く当てすぎると，基板のパターン（銅
箔）がはがれてしまうことがありますので，注意して
ください。また，従来の半田よりも粘性が強いため，
IC端子などが半田ブリッジしないように注意してく
ださい。
・ 半田こてのこて先は，必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from exposure to
high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small containers
to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemicals
are not in use.
• Avoid using chemicals as much as possible. When using chemicals,
divide only required amount to a small plate from the container and
use up it.
PLASTIC PARTS
Be careful to the following points for plastic parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning plastic
parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint
thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a plastic
part.
Be careful not to tighten screws too much.
各種薬品の取り扱いについて
現在使用されている薬品の中には揮発性の高い薬品もありま
す。
それらを不用意に取り扱い蒸発させてしまうと，環境や健康へ
影響を与えたり，資源の無駄使いになります。
各種薬品は，下記の点に注意して取り扱ってください。
・保管場所を定め，高温になったり直射日光の当たらない場所
に密閉して保管してください。
・小分け（ハンドラップ等）する数は必要最小限に留め，容器に
よる自然蒸発を防いでください。
・作業に使用しない時は，必ずキャップ等をして自然蒸発を防
いでください。
・薬品を使用する回数を極力少なくし，使用する場合は使用す
る量だけ容器より出して受け皿に残さないようにしてくださ
い。
樹脂系部品の取り扱いについて
本機に使用されている樹脂系の部品は，下記の点に注意して取
り扱ってください。
・清掃には薬品を使用せず，清掃紙や清掃布を使用してくださ
い。
 やむを得ず汚れがひどくて薬品を使用する場合は，シンナー，
ケトン，エーテルは使用しないでください。
・各部品の取り付けには指定されたねじを使用し，部品に対し
て垂直に取り付けてください。
 また，ねじを締め付ける時は，無理な力を加えないでくださ
い。

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
1-1
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 Vdc), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the Connecting Cord (DK-415).
1-2. PRECAUTION ON REPLACING THE VC-618 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
00
32C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32....Turnonpoweragain.
Block Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
00
32C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32....Turnonpoweragain.
Block Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
C 0 6 0 0 The battery pack temperature is high. Change the battery pack or place it in a cool place.
C1 3 0 1Memory card is unformatted.
Memory card is broken.
Format the memory card.
Insert a new memory card.
C 1 3 0 2 Access error Remove the power source. Reconnect it again and operate your cam-
corder again.
C 1 3 0 3 Access error (External media) Turn power off and turn power on again.
C 1 3 0 4 Drive fault (External media) Turn power off and turn power on again.
C
E
32
61
60
00
Difficult to adjust focus
(Cannot initialize focus) Turn power off and turn power on again.
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Turn power off and turn power on again.
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.
– ENGLISH –
Ver. 1.1 2012.05
( )
*
*

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
1-2
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
E6 1 1 0Zoom operations fault
(Cannot initialize zoom lens.) Turn power off and turn power on again.
E6 1 1 1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Turn power off and turn power on again.
E6 1 3 0Reset position detection error on the stepper
iris initializing Refer to [1-4. METHOD OF COPING WITH LENS ERROR].
E6 2 0 0
Handshake correction function does not work
well. (With PITCH angular velocity sensor
output stopped.)
Turn power off and turn power on again.
E6 2 0 1
Handshake correction function does not work
well. (With YAW angular velocity sensor
output stopped.)
Turn power off and turn power on again.
E 6 2 0 2 Abnormality of IC for steadyshot. Turn power off and turn power on again.
E6 2 0 3IC for steadyshot and micro controller com-
munication abnormality among. Turn power off and turn power on again.
E6 2 0 4Image vibration correction during
handshake function does not work. Turn power off and turn power on again.
E 6 2 1 0 Shift lens initializing failure. Turn power off and turn power on again.
E 6 2 1 1 Shift lens overheating (Pitch) Refer to [1-4. METHOD OF COPING WITH LENS ERROR].
E 6 2 1 2 Shift lens overheating (Yaw) Refer to [1-4. METHOD OF COPING WITH LENS ERROR].
E 6 2 2 0 Abnormality of thermistor. Refer to [1-4. METHOD OF COPING WITH LENS ERROR].
E 9 1 0 1 Abnormality when flash is being charged. Turn power off and turn power on again.
E 9 1 0 2 Abnormality of flash unit. Turn power off and turn power on again.
E9 1 0 3Abnormality of flash unit Temperature
detection. Turn power off and turn power on again.
E9 2 0 1Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each out-
put of DC/DC converter on IC4301 of VC-618 board with the AC
adaptor connected DC JACK (J901).
(The minimum connection to periphery)
E9 4 0 0Fault of writing or erasing or back up the
flash memory Check the OneNAND of CPU (IC1301 on the VC-618 board).
E 9 4 0 1 Internal flash memory fault Turn power off and turn power on again.
E 9 4 0 2 BGM data error Check the CPU (IC1301 on the VC-618 board).
E 9 5 0 0 GPS hardware error
Check whether the flexible flat cable of the GPS module is broken,
and check whether it is inserted imperfectly. If there is no problem the
flexible flat cable, inspect or replacement of the GPS module.
E 9 6 0 0 Map area mount error Inspect or replacement of the VC-618 board.
E 9 7 0 0 Projector hardware error Turn power off and turn power on again.
Note 3: When the lens device was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
– ENGLISH –
*
*
*
*
*
*
*
*
*
*
*
*
*
1-4. METHOD OF COPING WITH LENS ERROR
When lens error is occurred, check the following items.
Lens error codes:
・E: 61: 30 (Reset position detection error on the stepper iris initializing)
・E: 62: 11 (Shift lens overheating (Pitch))
・E: 62: 12 (Shift lens overheating (Yaw))
・E: 62: 20 (Abnormality of thermistor)
Check items:
1. Replace the lens.
2. Replace the VC-618 board or IC1301 on the VC-618 board.
3. Check that the square wave is appeared below points.
・BODY_VD_LENS (pin 7of CN6601 or pin 6of IC6601)
・BODY_DATA_LENS (pin 3of CN6601 or pin 4of IC6602)
・LENS_DATA_BODY (pin 4of CN6601 or pin 5of IC6603)
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
1-3
1-1. 修理時の電源供給について


方法：

1-2. VC-618基板交換時の注意

仕向けデータ


USBシリアルNo.



– JAPANESE –
1-3. 自己診断機能
1-3-1.自己診断機能について





1-3-2.自己診断表示





00
C23



 

 
 


  


1-3-3.自己診断コード表
自己診断コード
症状／状態 対応／方法
対
応
者
ブロック
機能
詳細
コード
      
      
   





      
      
      









  
 
      
注意1： 
注意2： 
Ver. 1.1 2012.05
()
*
*

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
1-4E
自己診断コード
症状／状態 対応／方法
対
応
者
ブロック
機能 詳細 コード
  
 
      
  
 
   
 
  
 
      
  
 
   
 
      
  
 
  
 
      
      
      
  
 
  







  
 
      
      
       

      
      
注意3： 
 
– JAPANESE –
*
*
*
*
*
*
*
*
*
*
*
*
*
1-4. レンズエラーの対処方法

レンズエラーコード：




チェック手順：
 
 
 
76
34
45
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link ACCESSORIES ASSEMBLY
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: F
• COILS
uH: H
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: , for example:
uA...: A... , uPA... , PA... ,
uPB... , PB... , PC... , PC... ,
uPD..., PD...
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は,補修用部品であるため,回路図及びセットに付いてい
る部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異なる場合があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
 金 被：金属被膜抵抗。
 サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA...,uPA...,uPB...,uPC...,uPD...等はそれぞれμA...,μPA...,μPB...,
μPC...,μPD...を示します。
The components identified by mark 0
or dotted line with mark 0are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
View Position
Right View
Left View
Front View
Bottom View
Top Vi e w
Back View
･Abbreviation
CH : Chinese model
CND : Canadian model
J : Japanese model
図面番号で部品を指定するときは基板名
又はブロックを併せて指定してください。
お願い
• 外装部品色表示
例：
 (SILVER) ：セットの色を表す。
 (Silver) ：部品の色を表す。
0印の部品，または0印付の点線で囲ま
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。
3GRIP Section
• SS-186 Board
8LCD Section
• PD-430 Board
qs Cabinet (L (Front))/
Cabinet (L (Rear) Section
• FB-225 Board
• LS-073 Board
qf Chassis (Upper) Section
• AU262 Board
• MT-072 Board
• VC-618 Board
• FP-1400 Flexible Board
• FP-1401 Flexible Board
• FP-1402 Flexible Board
• FP-1403 Flexible Board
• FP-1405 Flexible Board
• FP-1406 Flexible Board
• FP-1407 Flexible Board
• FP-1408 Flexible Board
1VF Section
2Handle Section
9Control Panel Section
• TK-072 Board
qa BT Panel Section
• HP-159 Board
• JK-399 Board
• XL-014 Board
qg Chassis (Lower) Section
• HD-043 Board
• US-018 Board
• FP-1409 Flexible Board
• FP-1410 Flexible Board
q; Cabinet (R) Section
• RK-001 Board
• TS-159 Board
4EXT Dummy
Cover (945)
7GP945 Assy
5Cabinet Bottom Assy
6Cabinet (Top (Rear)) Assy
qd MS-460 Assy

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible
that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
– JAPANESE –
– ENGLISH –
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け，折れ等
がないことを確認する。
 また，コネクタへの接続は，差し込み不足や斜め差しにならないよ
うに注意する。
• コネクタを取り外す時に，線材部（極細）を持って引っ張ると断線す
る恐れがありますので，絶対に線材部（極細）を持って引っ張らない
でください。
• 線材部（極細）を押さえながらコネクタを差し込むと，線材部（極細）
が断線する恐れがありますので，絶対に線材部（極細）には負担をか
けないでください。
• 金メッキされているフレキシブル基板には，強い負担をかけないで
ください。
వ┵ߩ೸߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰෰ߒߡߊߛߐ޿ޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡ޿ࠆ
႐ว߽޽ࠆߩߢᵈᗧߒߡߊߛߐ޿㧕
వ┵ߩ೸߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰෰ߒߡߊߛߐ޿ޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡ޿ࠆ
႐ว߽޽ࠆߩߢᵈᗧߒߡߊߛߐ޿㧕

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
ns : not supplied
1. Remove to numerical order (1to 7) in the left figure.
DISASSEMBLY
5#119 X 4
Screw
Bottom View
#119
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#119: M2.6 X 5.0
(Black)
7-627-556-58
5.0
2.6
ns
#49
#119
3Grip Section
(See page 2-17)
71
63
55
4
4
2Handle Section
(See page 2-19)
1VF Section
(See page 2-18)
Overall Section-2
(See page 2-4)
#49
42
Ref. No. Part No. Description Ref. No. Part No. Description
1 4-284-137-01 CLAMP, CABLE
*2 4-284-136-01 COVER (945), EXT DUMMY
3 X-2581-568-1 BOTTOM ASSY, CABINET
4 4-165-229-01 FOOT, RUBBER
5 3-288-392-11 WASHER (D), TRIPOD
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#119 7-627-556-58 SCREW +P 2.6X5
6#49 X 4
Bottom View
#49
7#49 X 1
Left View
#49

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-4
2-1-2. OVERALL SECTION-2 1. Remove to numerical order (1to 7) in the left figure.
DISASSEMBLY
1 Stand up LCD → #49 X 4 → Rotate LCD → Tilt LCD
Screw
Top View
#49
#49
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
5.0
2.0
Tighten these screws to the following torque.
#49
#49
#49
#191
Reinforcement side
60
#49
#53
SP901
56
58
(Claw)
5Control Panel Section
(See page 2-12)
4LCD Section
(See page 2-11)
151
(Note 1)
257
359
(Note 2)
652
753
54
55
(0.4 0.04N m (4.0 0.4kgf cm))
Overall Section-3
(See page 2-5)
Except FS100C/
FS100CK
Ref. No. Part No. Description Ref. No. Part No. Description
51 X-2581-567-1 CABINET (TOP (REAR)) ASSY
(EXCEPT FS100C/FS100CK) (Note 1)
51 X-2581-569-1 CABINET (TOP (REAR)) CN ASSY
(FS100C/FS100CK) (Note 1)
52 3-069-286-31 SHOE, ACCESSORY
53 4-269-179-01 CABINET (TOP (FRONT))
54 2-178-550-01 HOLDER, SPEAKER
55 4-269-180-01 RETAINER, SP
56 1-839-082-11 CABLE, FLEXIBLE FLAT (FFC-246)
(EXCEPT FS100C/FS100CK)
57 A-1826-322-A GP945 ASSY (EXCEPT FS100C/FS100CK)
58 4-269-034-01 FRAME, GP (EXCEPT FS100C/FS100CK)
59 4-269-048-01 COVER, AU (Note 2)
60 3-637-901-02 SCREW M2.6X5
SP901 1-825-968-11 LOUDSPEAKER (1.8CM)
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#53 3-080-206-21 SCREW, TAPPING, P2
#119 7-627-556-58 SCREW +P 2.6X5
#191 4-188-735-01 SCREW (M1.7)
2#191 X 1
Top View#191
4Ref. No. 60 X 4
Top View Ref. No. 60
Ref. No. 60
5#49 X 2
Top Vi e w
#49
6#49 X 4
Top View
#49
7#49 X 3
Top View #49
#119: M2.6 X 5.0
(Black)
7-627-556-58
5.0
2.6
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
Note
Note 1: When replacing this part,
be careful whether a LOGO
is existed or not.
X-2581-567-1
GPS logo
X-2581-569-1
឵ᤨߦࡠࠧߩ᦭ήߦᵈᗧ
ߒߡߊߛߐ޿ޕ
GPSߩࡠࠧ
Note 1:
X-2581-567-1
X-2581-569-1
Note 2: Refer to "Assembly-3: Installation Cautions of the AU
Cover.".
Note 2: “Assembly-3: Installation Cautions of the AU Cover.” を参照
してください。

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-5
2-1-3. OVERALL SECTION-3 1. Remove to numerical order (1to 5) in the left figure.
DISASSEMBLY
1#49 X 4
Screw
Right View Bottom View
#49
#49
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
#49
#49
#49
#49
#49
#49
#191
#49
#49
#49 #49
1Cabinet (R) Section
(See page 2-13)
Chassis (Lower) Section
(See page 2-6)
3BT Panel Section
(See page 2-14)
4Cabinet (L (Front))/
Cabinet (L (Rear) Section
(See page 2-15)
5Cabinet (L (Front))/
Cabinet (L (Rear) Section
(See page 2-15)
2101
102
1(Claw)
4(Claw)
5(Claw)
4(Claw)
1(Claws)
3(Claws)
5(Claw)
Reinforcement side
2#49 X 4 → #49 X 1
Top View Left View
#49
#49
3#49 X 2 → Open HDMI Lid (3-1) → Ref.No.102 X 2 → Open HDMI Lid (3-2) → #191 X 2 → #49 X 3
Top View Bottom ViewBack View
#49
#191
#49
Ref.No.102
3-2
3-1
Ref. No. Part No. Description Ref. No. Part No. Description
101 4-269-049-01 CABINET (TOP (LOWER))
102 7-621-775-80 SCREW +B 2.6X16
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#191 4-188-735-01 SCREW (M1.7)
4#49 X 6
Bottom View Left View
#49
#49
#49
5#49 X 1
Bottom View
#49

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-6
2-1-4. CHASSIS (LOWER) SECTION
ns : not supplied
#119
#119
#119
#119
#119
#49
#49
#49
#49
#50
157
#50
#49
157
157
#119
156
154
2Chassis (Upper) Section
(See page 2-7)
BT Holder Section
(See page 2-16)
1155
153
ns
BH2001
(Note)
BT2001
(Note)
151
151
151
152
151
151
: BT2001 (LITHIUM BATTERY SECONDARY)
Board on the mount position.
(See page 6-46)
1. Remove to numerical order (1to 2) in the left figure.
DISASSEMBLY
1#50 X 4
Right View
#50
Note
Note: Replace the battery holder (BH2001) together when replacing
the lithium storage battery (BT2001) on the MS-460 board. (The
battery holder removed once cannot be usedagain.)
When mounting these parts, mount new battery holder first and
attach new lithium storage battery next.
Note:
MS-460基板のリチウム蓄電池 (BT2001) を交換する場合は
バッテリホルダ (BH2001) も同時に新品に交換してください。
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は、先にバッテリホルダを取り付けてから
リチウム蓄電池を装着してください。
2Ref. No. 157 X 4 → #49 X 4
Right View Left View Bottom View
Ref. No. 157
Hole
#49
#49
Disconnect
flexible boards,
harness
Ref. No. 157
Ref. No. 157
Ref. No. Part No. Description Ref. No. Part No. Description
151 4-269-036-01 PLATE, TRIPOD
152 4-284-132-01 WASHER (D LARGE), TRIPOD
153 4-269-031-01 FRAME (LOWER), MAIN
154 4-284-134-01 GASKET (B)
155 A-1826-028-A MS-460 BOARD, COMPLETE
156 4-284-133-01 GASKET (A)
157 4-671-539-01 SCREW, M2 +P EG GRIP
BH2001 1-251-928-21 SOCKET, BATTERY (Note)
BT2001 1-756-135-31 BATTERY LITHIUM SECONDARY (Note)
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#50 2-891-494-11 SCREW (M2), NEW TRUSTER, P2
#119 7-627-556-58 SCREW +P 2.6X5
Caution :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換してく
ださい。
使用済み電池は、取扱指示に従って処分してください。
Screw
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
3.0
2.0
#119: M2.6 X 5.0
(Black)
7-627-556-58
5.0
2.6
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-7
1. Remove to numerical order (1to 6) in the left figure.
DISASSEMBLY
1#49 X 1
#49
Top View Disconnect
flexible board
202
210 211
#49
2Mount Block Section
(See page 2-8)
#49
6216
VC-618
AU-262
#119
#119
#119
#49
#50
#49
#191
205
203
213
214
204
206
(Note 3)
A
B
AB
218
219
217
220
221
220
207
208
222
5215
3209
(Note 2)
4212
1201
(Note 1)
223
2Ref. No. 223
Ref. No. 223
Top View Disconnect
flexible board
Note
Note 1: Refer to "Assembly-1: Installation Cautions of the FPC
Clamp.".
Note 1: “Assembly-1: Installation Cautions of the FPC Clamp.”を
参照してください。
Ref. No. Part No. Description Ref. No. Part No. Description
201 4-269-037-01 CLAMP, FPC (Note 1)
202 1-883-347-11 FP-1407 FLEXIBLE BOARD
203 4-284-255-01 SPACER (A)
204 1-883-342-11 FP-1402 FLEXIBLE BOARD
205 1-883-345-11 FP-1405 FLEXIBLE BOARD
206 4-284-130-01 LABEL, FUSE REPLACEMENT CAUTION (Note 3)
207 1-883-343-11 FP-1403 FLEXIBLE BOARD
208 1-883-346-11 FP-1406 FLEXIBLE BOARD
209 A-1826-363-A VC-618 BOARD, COMPLETE (SERVICE) (Note 2)
210 4-284-124-01 SHEET (A), RADIATION
211 1-839-086-11 CABLE, FLEXIBLE FLAT (FFC-256)
212 4-269-033-01 HEAT SINK, VC
213 1-883-348-11 FP-1408 FLEXIBLE BOARD
214 3-941-343-01 TAPE (A)
215 4-269-032-01 FRAME, VC
216 A-1826-041-A AU-262 BOARD, COMPLETE
(EXCEPT FS100C/FS100CK)
216 A-1826-042-A AU-262 BOARD, COMPLETE (FS100C/FS100CK)
217 1-839-084-11 CABLE, FLEXIBLE FLAT (FFC-249)
218 4-269-038-01 PLATE, HOOK (R)
219 4-269-026-01 FRAME (UPPER), MAIN
220 4-269-036-01 PLATE, TRIPOD
221 4-269-035-01 PLATE, SHOE TRIPOD
222 4-293-516-01 SPACER (D)
223 4-671-539-01 SCREEN, M2 +P EG GRIP
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#50 2-891-494-11 SCREW (M2), NEW TRUSTER, P2
#119 7-627-556-58 SCREW +P 2.6X5
#191 4-188-735-01 SCREW (M1.7)
4#49 X 3
Top Vi e w
#49
5#49 X 3
Top View
#49
6#50 X 2
Bottom View
#50
3#191 X 3
#191
Top Vi e w
Screw
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
3.0
2.0
#119: M2.6 X 5.0
(Black)
7-627-556-58
5.0
2.6
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
Note 2: Refer to "Assembly-2: Installation Cautions of the VC-
618 Board.".
Note 2: “Assembly-2: Installation Cautions of the VC-618 Board.”
を参照してください。
Note 3: Refer to "Assembly-7: Putting position of the Fuse
Replacement Caution Label.".
Note 3: “Assembly-7: Putting position of the Fuse Replacement
Caution Label.”を参照してください。
2-1-5. CHASSIS (UPPER) SECTION

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-8
2-1-6. MOUNT BLOCK SECTION
258
259
#191
#191
#191
261
260 263
262
256
#191
#191
253
Cabinet (F) Section
(See page 2-10)
Imager Unit Section
(See page 2-9)
251
(including ASM080 (CMOS imager) and
IS-089 complete board) (Note 4)
254
#191
257
(Note 3)
257
(Note 3)
257
(Note 3)
252
(Note 1, 2)
252
(Note 1, 2)
252
(Note 1, 2)
257
(Note 3)
255
251 A-1826-171-A SERVICE, MOUNT BLOCK ASSY
(including ASM080 (CMOS imager) and IS-089 complete board) (Note 4)
*252 Selection Parts IM WASHER (A), ADJUST (Note 1, 2)
253 4-269-055-01 MB SHEET, MASK (945)
254 4-269-089-01 CABINET, MASK
255 4-269-067-01 SHEET, MT RADIATION
Ref. No. Part No. DescriptionRef. No. Part No. Description
256 4-269-068-01 HEAT SINK, MT
257 4-135-726-01 SHEET (CM), RADIATION (Note 3)
258 1-883-340-11 FP-1400 FLEXIBLE BOARD
259 1-883-341-11 FP-1401 FLEXIBLE BOARD
260 4-269-069-01 FRAME, MT
261 4-269-066-01 HEAT SINK, F
262 A-1826-045-A MT-072 BOARD, COMPLETE
263 1-839-087-11 CABLE, FLEXIBLE FLAT (FFC-257)
#191 4-188-735-01 SCREW (M1.7)
Screw
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
Note
Note 1: The IM adjust washers (A) differ in thickness.
Make sure to return the removed IM adjust washers to
original places.
When replacing IM adjust washers, refer to "SELEC-
TION PARTS".
If the original state cannot be restored due to loss of
the IM adjust washer, for example, replace the Mount
Block Assy (Service).
Note 1: IM調整ワッシャ (A)は，それぞれ厚さが異なります。
取り外したIM調整ワッシャは，必ず元の位置に戻してく
ださい。
また，IM調整ワッシャを交換する際は，“SELECTION
PARTS”を参照してください。
IM adjust washerを紛失するなどして元の状態に戻せな
くなった場合は，Mount Block Assy (Service) を交換し
てください。
Note 2: Refer to "Assembly-4: Putting position of the IM Adjust
Washer (A).".
Note 2: “Assembly-4: Putting position of the IM Adjust Washer
(A).” を参照してください。
Note 3: The CM Radiation Sheet when peeling off once, so that
it cannot be reused.
Note 3: CM Radiation Sheetは一度剥がすと粘着力が弱くなるた
め、再利用はしないでください。
Note 4: Precautions for Replacement of the Mount Block Assy
Service
As Mount Block Assy Service may be damaged by static
electricity from its structure, handle it carefully like for
the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
Note 4: マウントブロックAssy サービス交換時の注意
マウントブロックAssy サービスは構造上，静電気によ
り破壊される恐れがあるため，MOS ICと同様に注意し
て取り扱ってください。
また，受光部にはゴミの付着，および強い光がはいるこ
とのないように注意してください。
SELECTION PARTS
Ref. No.252
Select the optimum thickness of washer.
4-185-995-01 IM WASHER (A), ADJUST (t = 0.05)
4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-9
2-1-7. IMAGER UNIT SECTION
ns : not supplied
Screw
Note
ns
306
#191
#191
305
303
302
301
304
(Note1, 2)
(All mounted parts and IS-089 complete board are not supplied,
but they are included in Cabinet (Front) Block Assy)
301 4-269-057-01 IM PLATE, IMAGER 945
302 4-269-058-01 IM PLATE, HEAT SINK 945
303 4-269-056-01 IM PLATE, LPF RETAINER 945
304 1-856-225-11 FILTER BLOCK, OPTICAL (Note1, 2)
305 4-277-410-01 IM TAPE, FLARE CUTTER
Ref. No. Part No. DescriptionRef. No. Part No. Description
306 4-269-083-01 IM CUTTER, FLARE
#191 4-188-735-01 SCREW (M1.7)
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
Note 1: Refer to "Replacement of Optical Filter Block".
Note 1: “Replacement of Optical Filter Block” を参照してください。
Note 2: Refer to "3-2. CLEANING PROCEDURE OF OLPF" on page
3-3 for method of cleaning the OLPF.
Note 2: OLPFの清掃方法は3-3ページの“3-2. CLEANING
PROCEDURE OF OLPF” を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-10
2-1-8. CABINET (F) SECTION
ns : not supplied
Screw
351 4-188-536-01 CAP, BODY
352 4-269-054-01 MB N PLATE (A (945))
*353 4-185-963-01 MB N PLATE SP (Note)
354 4-269-087-01 RING, MOUNT
355 4-269-085-01 BUTTON, LENS LOCK
356 4-269-064-01 PIN (945), LENS LOCK
357 4-269-084-01 SPRING, LENS LOCK
358 4-269-086-01 COVER, LENS LOCK
359 4-269-065-01 SHAFT (945), LENS LOCK GUIDE
360 4-269-088-01 RING, LENS
Ref. No. Part No. DescriptionRef. No. Part No. Description
361 4-269-071-01 CABINET, MT INNER
362 A-1773-802-A MB CONTACT UNIT, N
#191 4-188-735-01 SCREW (M1.7)
#195 3-197-324-01 M1.7X2.5X3GF (D4X0.5)
#234 4-186-545-11 SCREW, 0+Z M1.7 SG (SPIN)
#191
#191
ns
#195
#191
#234
362
361
360
354
359
358
355 356
357
353
(Note)
352
351
#191: M1.7 X 3.5 (Tapping)
(Black)
4-188-735-01
3.5
1.7
2.5
1.7
#195: M1.7 X 2.5
(Silver)
3-197-324-01
Note
Note: Refer to "Assembly-5: Apply grease on the MB N Plate
SP.".
Note: “Assembly-5: Apply grease on the MB N Plate SP.” を参照
してください。
#234: M1.7 X 5.5
(Silver)
4-186-545-11
5.5
1.7

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-11
2-1-9. LCD SECTION
Note
Screw
Note 3: Refer to "Assembly-6: Apply grease on the LCD Lock
Bolt.".
Note 3: “Assembly-6: Apply grease on the LCD Lock Bolt.”
を参照してください。
Note 4: Cut SHEET, LIGHT INTERCEPTION (3-089-986-01)
into the desired length and use it.
Note 4: SHEET, LIGHT INTERCEPTION (3-089-986-01)は
指定のサイズに切って使用すること。
Note 1:
P Cabinet (C) Assyの爪の無い側を矢印方向に
持ち上げる。
P Cabinet (C) Assyの爪を折らないために、
以下の手順でP Cabinet (C) Assyを取り外し
てください。
1
P Cabinet (C) Assyを矢印方向にスライドさせて
P Cabinet (C) Assyを取り外す。
2
Claws
401 4-269-207-01 CABINET (C), P (Note 1)
402 A-1826-052-A PD-430 BOARD, COMPLETE
403 4-269-204-01 SHEET (PD)
404 4-269-203-01 FRAME, LCD
405 4-283-280-11 CUSHION (91000), LCD
406 4-269-202-01 CABINET (M), P
407 1-471-504-11 MAGNET (ND5X3.5X2.4-B) (Note 2)
408 4-269-197-01 CAP, LCD KNOB
409 4-269-196-01 KNOB, LCD LOCK (Note 3)
410 4-269-195-01 BOLT, LCD LOCK (Note 3)
Ref. No. Part No. DescriptionRef. No. Part No. Description
411 4-269-206-01 CABINET (REAR), HINGE
412 1-967-783-11 HARNESS (COAXIAL CABLE)
413 X-2580-324-1 HINGE ASSY, PANEL
414 4-269-205-01 CABINET (FRONT), HINGE
415 3-089-986-01 SHEET (L), LIGHT INTERCEPTION (Note 4)
LCD901 1-811-403-11 LCD WITH TOUCH PANEL
LED901 1-487-270-11 BLOCK, LIGHT GUIDE PLATE (3.5)
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#50 2-891-494-11 SCREW (M2), NEW TRUSTER, P2

#50
#49
#49
#49
#50
#50
#49
LCD901
LED901
401
(Note 1)
403
404
405
406
407
(Note 2)
409
408
410
(Note 3)
414 413
411
412
402
415
(Size: 5.0mm X 5.0mm)
(Note 4)
#49: M2.0 X 4.0
(Black)
2-630-005-31
4.0
2.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
3.0
2.0
Put the marking side together
on the position of figure when
you install the magnet.
Marking
Note 2: マグネットを取付ける際は，
マ−キング面を図の位置に
あわせてください。
マーキング
Note 2:
Note 1:
1
2
Claws
Install the P cabinet (C) assembly in the
following procedure to prevent the claw of P
cabinet (C) assembly from breaking.
Lift up the opposite side of the claw of P cabinet
(C) assembly in the arrow direction.
Remove the P cabinet (C) assembly, sliding it in
the arrow direction.
1. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇: Solder
DISASSEMBLY
Ver. 1.1 2012.05

NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-12
2-1-10. CONTROL PANEL SECTION
ns : not supplied
451 X-2581-577-1 PANEL ASSY, CONTROL
452 3-288-474-01 RUBBER, PANEL RETAINER
453 4-269-120-01 BUTTON, SS
454 4-269-121-01 RUBBER, SS BUTTON
455 1-839-083-11 CABLE, FLEXIBLE FLAT (FFC-248)
Ref. No. Part No. DescriptionRef. No. Part No. Description
456 A-1826-043-A TK-072 BOARD, COMPLETE
457 4-269-181-01 RETAINER, TK
458 1-489-423-11 SWITCH BLOCK, CONTROL (AU94500)
#53 3-080-206-21 SCREW, TAPPING, P2
Screw
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
5.0
2.0
TK-072
#53
ns
#53
451
452
452
457
454
453
456
455
458