Sony VPL-DW125 User manual

4-444-750-11 (2)
© 2012 Sony Corporation
Data
Projector
Operating Instructions
Before operating the unit, please read this manual and supplied Quick Reference Manual
thoroughly and retain it for future reference.
VPL-DX145/DX125
VPL-DW125
Not all models are available in all countries and area. Please check
with your local Sony Authorized Dealer.

2Table of Contents
Table of Contents
Overview
Location and Function of Controls .... 4
Main Unit ..................................... 4
Connector Panel ........................... 5
Remote Commander and Control
Panel Keys ................................. 5
Preparation
Connecting the Projector ................... 8
Connecting a Computer ................ 8
Connecting a Video equipment .... 9
Connecting a USB memory
device ...................................... 10
Connecting a USB wireless LAN
module .................................... 10
Projecting/Adjusting an
Image
Projecting an Image ......................... 11
Adjusting the Projected image ... 12
Turning Off the Power ................ 15
Adjustments and Settings
Using a Menu
Using a MENU ................................ 16
The Picture Menu ............................. 17
The Screen Menu ............................. 18
The Function Menu .......................... 22
The Operation Menu ........................ 23
The Connection/Power Menu .......... 24
The Installation Menu ...................... 26
The Information Menu ..................... 27
Network
Using Network Features ...................28
Displaying the Control Window of
the Projector with a Web
Browser ...................................28
Confirming the Information
regarding the Projector ............29
Operating the Projector from a
Computer .................................29
Using the e-mail report
Function ...................................30
Presentation Function via
Network
Using Presentation Function via
Network .........................................32
Installing Projector Station for
Network Presentation ..............32
Starting Projector Station for
Network Presentation ..............32
Projecting an Image ....................33
Connection Settings ....................33
Using the Controller ...................34
Projecting an Image using
USB Connection
Projecting an Image using USB
Connection ....................................35
Starting USB Display .................35
Projecting an Image ....................35
Using the Controller ...................35

3
Table of Contents
USB Media Viewer
Using USB Media Viewer ................36
Thumbnail Mode ........................37
Option Menu ...............................37
Display Mode .............................38
Option Menu ...............................38
Slideshow Mode ......................... 38
Option Menu ...............................39
Others
Indicators ..........................................40
Messages List ...................................41
Troubleshooting ...............................42
Replacing the Lamp .........................44
Cleaning the Air Filter .....................46
Specifications ...................................47
Projection Distance .......................... 52
Dimensions .......................................57
Index .................................................60

4Location and Function of Controls
BOverview
Location and Function of Controls
aFocus ring (page 12)
bZoom ring (page 12)
cLens
dRemote control detector
eFoot adjust button (page 13)
fFront foot (adjustable) (page 13)
gAir filter cover/Ventilation holes
(intake) (page 46)
hLamp cover (page 44)
iRear feet (adjustable) (page 13)
jVentilation holes (exhaust)
Do not place anything near the ventilation
holes as this may cause internal heat
buildup. Do not place your hand near the
ventilation holes and the circumference as
this may cause injury.
kConnector panel (page 5)
lSecurity bar
Connects to a commercially available
security chain or wire.
mSecurity lock
Connects to an optional security cable
manufactured by Kensington.
For details, visit Kensington’s web site.
http://www.kensington.com/
nControl panel keys (page 5)
oVentilation holes (intake)
pSpeaker
qLAMP/COVER indicator
(page 40)
rON/STANDBY indicator
(page 40)
Main Unit
Caution
54
3
2
1
8
6
7
9
0
qh
qa
qs
qd
q
f
qj
qk
qg

5
Location and Function of Controls
Overview
Input (pages 8, 9)
aINPUT A
Video: RGB/YPBPRinput connector
Audio: Audio input connector
bINPUT B
Video: HDMI input connector
Audio: HDMI input connector
cVIDEO
Video: Video input connector
Audio: Audio input connector
The audio inputs of INPUT A and VIDEO are
shared.
Others
dLAN connector (page 28)
eAC IN (∼) socket
Connects the supplied AC power cord.
fUSB connector (Type A) ( )
(pages 10, 36)
gUSB connector (Type B) ( )
(page 35)
Remote Commander Control Panel Keys
aTurning on the power/Going to
standby mode
?/1(On/Standby) key
bSelecting an input signal
(page 11)
INPUT key
Connector Panel
127 4 63
53
Note
Remote Commander and Control Panel Keys
2
3
4
5
6
1
4
7
INPUT
MENU
APA ECO MODE
RETURN
ASPECT
D ZOOM
KEYSTONE
ENTER
VOLUME
PATTERN
FREEZE
BLANK
MUTING
RESET
36
12

6Location and Function of Controls
cOperating a menu (page 16)
MENU key
RESET key
ENTER /V/v/B/b(arrow) keys
RETURN key
dAdjusting the image (page 12)
ASPECT key (page 18)
KEYSTONE key (page 14)
PATTERN key
This function is not available.
APA (Auto Pixel Alignment) key*
(page 14)
*Use this key when inputting a computer
signal via the RGB input connector
(INPUT A).
eUsing various functions during
projecting
D ZOOM (Digital Zoom) +/– key*
Enlarges the image with the center of it
as a starting point while projecting.
1Press the D ZOOM + key to display
the digital zoom icon on the projected
image.
2Press the V/v/B/bkeys to move the
digital zoom icon to the point on the
image you want to enlarge.
3Press the D ZOOM + key or the D
ZOOM – key repeatedly to change the
enlargement ratio. The image can be
enlarged up to 4 times.
Press the RESET key to restore the
previous image.
BLANK key
Cuts off the projected image
temporarily. Press again to restore the
previous image. Picture muting helps
reduce power consumption.
MUTING key
Mutes the audio output temporarily.
Press again to restore the previous
volume.
VOLUME +/– key
Adjusts the volume output.
FREEZE key
This function is not available.
*: Use this key when inputting a computer
signal. But it may not be used
depending on the resolution of the input
signal.
fSetting the energy–saving mode
easily
ECO MODE key
Energy-saving mode can be set easily.
Energy-saving mode consists of “Lamp
Mode,” “With No Input,” “With Static
Signal” and “Standby Mode.”
1Press the ECO MODE key to display
the ECO Mode menu.
2Press the V/vkey or ECO MODE key
to select “ECO” or “User” mode.
ECO: Sets each mode to the optimum
energy-saving value.
Lamp Mode: Low
With No Input: Standby
With Static Signal: Lamp
Dimming
Standby Mode: Low
User: Sets each item of the ECO
mode menu as you desire (go to
step 3).
3Select “User” then press the bkey.
The setting items appear.
4Press the V/vkey to select the item
then press the ENTER key.
5Press the V/vkey to select the setting
value.
Note
Note
RETURN
ECO
User
ECO Mode
:Sel :Back
ECO Mode Menu
RETURN
Lamp Mode High
Auto Power Saving
Standby Mode
Off
With No Input
Lamp Dimming
With Static Signal
Standard
User
:Sel :Set :Back

7
Location and Function of Controls
Overview
6Press the ENTER key.
The screen returns to the previous
menu.
For details on ECO Mode settings, see
“Lamp Mode,” “With No Input,” “With
Static Signal” and “Standby Mode” on
the Connection/Power menu (page 24).
Others
gInfrared transmitter
About remote commander operation
• Direct the remote commander toward the
remote control detector.
• The shorter the distance between the
remote commander and the projector is,
the wider the angle within which the
remote commander can control the
projector becomes.
• Make sure that nothing obstructs the
infrared beam between the remote
commander and the remote control
detector on the projector.

8Connecting the Projector
BPreparation
Connecting the Projector
• Make sure all the equipment is powered off when connecting the projector.
• Use the proper cables for each connection.
• Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or
cause a malfunction. When pulling out a cable, be sure to grip it by the plug, not the cable itself.
• For more information, refer also to the instruction manuals of the equipment you are connecting.
• Use a no-resistance audio cable.
Connection with a computer is explained for each input signal.
INPUT A
It is recommended that you set the resolution of your computer to 1024 × 768 pixels (VPL-DX145/
DX125) or 1280 × 800 pixels (VPL-DW125) for the external monitor.
INPUT B
• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal
or CEC (Consumer Electronics Control) Signal.
• It is recommended that you set the resolution of your computer to 1024 × 768 pixels (VPL-DX145/
DX125) or 1280 × 800 pixels (VPL-DW125) for the external monitor.
Notes
Connecting a Computer
Note
For connecting a computer with an RGB output connector.
RGB output
connector
Audio output
connector
Mini D-sub 15-pin cable (supplied)
Computer
Audio cable (Stereo mini plug)
(not supplied)
Notes
For connecting a computer with an HDMI output connector.
HDMI output
connector
HDMI cable
(not supplied)
Computer

9
Connecting the Projector
Preparation
USB connector (Type B) ( )
For connecting to a computer with a USB connector (“Projecting an Image using USB
Connection” (page 35)).
Connections with a DVD player or BD player are explained for each input signal.
VIDEO
For connecting video equipment with a video output connector.
INPUT A
For connecting video equipment with a YPBPRoutput connector.
Connecting a Video equipment
USB A-B cable (not
supplied)
Computer
USB connector
(Type A)
Video cable (not supplied)
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)
Video output
connector
Audio output
connector
Video equipment
Component – Mini D-sub 15-pin cable (not supplied)
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)
Video equipment
YPBPRoutput
connector
Audio output
connector

10 Connecting the Projector
INPUT B
• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal
or CEC (Consumer Electronics Control) Signal.
USB connector (Type A) ( )
For connecting a USB memory device (“Using USB Media Viewer” (page 36)).
USB connector (Type A) ( )
For connecting a USB wireless LAN module IFU-WLM3 (supplied) (“Presentation Function
via Network” (page 32)).
• Undesignated USB wireless LAN modules do not work.
• When connecting/disconnecting the USB wireless LAN module, make sure that the projector is in
Standby mode (Standby Mode: “Low”), or the AC power cord is unplugged from the wall outlet.
Notes
Connecting a USB memory device
Connecting a USB wireless LAN module
Notes
Video equipment
HDMI cable
(not supplied)
HDMI output
connector
For connecting video equipment with an HDMI output connector.
USB memory device
(not supplied)
USB wireless LAN module
IFU-WLM3 (supplied)

11
Projecting an Image
Projecting/Adjusting an Image
BProjecting/Adjusting an Image
Projecting an Image
The size of a projected image depends on the distance between the projector and screen. Install
the projector so that the projected image fits the screen size. For details on projection distances
and projected image sizes, see “Projection Distance” (page 52).
1Plug the AC power cord into the wall
outlet.
2Connect all equipment to the projector
(page 8).
3Press the ?/1key to turn on the unit.
4Turn on the connected equipment.
5Select the input source.
Press the INPUT key on the projector to
display the menu for switching input
signal on the screen. Press the INPUT
key repeatedly, or press the V/vkey to
select an image to be projected.
6When projecting a computer image,
switch your computer’s output to
external display.
The method to switch the output varies
depending on the type of computer.
(Example)
To project image files stored in a USB
memory device, see “USB Media
Viewer” (page 36). To project an image
using USB Connection, see “Projecting
an Image using USB Connection”
(page 35). To use Presentation Function
via Network, see “Presentation Function
via Network” (page 32).
Computer
Video equipment
Projector
Wall outlet
1
2
5
4
3
6
+

12 Projecting an Image
7Adjust the focus, size and position of
the projected image (page 12).
Adjusting the Projected image
Focus Size (Zoom) Position
Focus ring
Zoom ring Foot adjust
button
Front foot
(adjustable)
Rear feet (adjustable)

13
Projecting an Image
Projecting/Adjusting an Image
Adjusting the tilt of the projector with the foot adjust button/rear feet
(adjustable)
By changing the tilt of the projector with the foot adjust button/rear feet (adjustable), you can
adjust the position of the projected image.
1Press and hold the foot adjust button,
then lift up the front of the projector to
adjust the angle.
2When the desired angle is achieved,
release the foot adjust button to lock the
position.
3Set the angle of the projector precisely
by turning the rear feet (adjustable).
• Be careful not to let the projector down on your fingers.
• Do not push hard on the top of the projector with the front foot (adjustable) extended.
• Do not forcedly turn the rear feet (adjustable) more than they should be adjusted. Doing so may
break them.
Changing the aspect ratio of the projected image
Press the ASPECT key on the remote commander to change the aspect ratio of the projected
image. You can also change the setting in Aspect of the Screen menu (pages 18, 20).
Notes

14 Projecting an Image
Correcting trapezoidal distortion of the projected image (Keystone feature)
Keystone feature may not work automatically when the screen is tilted. In this case, set
keystone manually.
1Press the KEYSTONE key on the remote
commander or select V Keystone in the
Installation menu.
2Use the V/v/B/bthe keys to set the value.
The higher the value, the narrower the top
of the projected image. The lower the
value, the narrower the bottom.
Since the Keystone adjustment is an electronic
correction, the image may be deteriorated.
Automatically adjusts Phase, Pitch and Shift of projected image while a
signal is input from a computer (APA (Auto Pixel Alignment))
Press the APA key on the remote commander. Press again to cancel adjusting during the setting.
You can also set APA in the Screen Menu (page 19). If Smart APA in the Function menu is set
to “On”, executes APA automatically when a signal is input (page 22).
Note
Increase the number
towards plus
Increase the number
towards minus

15
Projecting an Image
Projecting/Adjusting an Image
1Press the ?/1key on the unit or the remote commander.
The projector starts shutdown and turns off. If you press the ?/1key within 10 seconds of
the message being displayed, shutdown is canceled.
2Unplug the AC power cord from the wall outlet.
To turn off without displaying confirmation message
Press and hold the ?/1key on the unit for a few seconds (page 41).
ECO gauge
This gauge indicates the current effectiveness of the projector’s ECO function.
(For details on the ECO function, see “ECO MODE key” (page 6) and “ECO” (page 24).)
The leaf icons are displayed when the projector is shut down. The number of displayed icons
varies according to how much energy is saved as a result of using the ECO function.
Turning Off the Power
ECO gauge

16 Using a MENU
BAdjustments and Settings Using a Menu
Using a MENU
The menu displays used for the explanation below may be different depending on the model you are
using.
1Press the MENU key to display the
menu.
2Select the setting menu.
Use the V/vkey to select the setting
menu then press the b key or ENTER
key.
3Select the setting item.
Use the V/vkey to select the setting
menu then press the b key or ENTER
key.
To return to the selection screen of the
setting menu, press the Bor RETURN
key.
4Make the setting or adjustment for the
selected item.
The setting method varies, depending on
the setting item.
If the next menu window is displayed,
select the item according to the
operations in step 3and then press the
ENTER key to register the setting.
To return to the selection screen of the
setting items, press the Bor RETURN
key. As an aid to setting or adjusting
items, you can press the RESET key to
return an item to its factory setting.
Using a pop-up menu
Press the V/v/B/bkey to select an item.
A selected item takes effect
immediately, except “Language”, which
will take effect after you press the
ENTER key.
Using the setting menu
Press the V/vkey to select the item.
A selected item takes effect
immediately. The previous screen is
restored.
Using the adjustment menu
To increase the value, press the V/bkey
and to decrease the number, press the
v/Bkey. If you press the ENTER key,
the selected item takes effect
immediately. The previous screen is
restored.
5Press the MENU key to clear the
menu.
The menu disappears automatically if no
operation is performed.
Note
5
Picture Mode Standard
Reset
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
Expert Setting
:Sel :Set :Back
Picture
Low
Setting menu
80
50
50
50
Picture Mode Standard
Reset
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
Expert Setting
:Sel :Set :Back
Picture
Low
5
Setting items
RETURN
Picture Mode
Dynamic
Standard
:Back
:Sel
Cinema
Game
Blackboard
Presentation
AdjustBack
Contrast

17
The Picture Menu
Adjustments and Settings Using a Menu
The Picture Menu
The Picture is used to adjust the picture for each input signal.
*1: When a computer signal is input, this option is available.
*2: The settings in the Picture return to their factory defaults, except for Picture Mode.
*3: When a video signal is input, this option is available.
*4: When the signal without color burst signal is input, this option is unavailable.
*5: When an analog TV signal is input, this option may not available, depending on the color system.
*6: When “Picture Mode” is set to the item other than “Presentation” or “Blackboard,” this option
is available.
*7: When “Picture Mode” is set to “Blackboard,” this option is unavailable.
Items Item descriptions
Picture Mode Dynamic: Emphasizes the contrast to produce a dynamic and vivid picture.
Standard: Provides an image which is natural and well balanced.
Presentation*1:Provides a bright image, suitable for presentations.
Blackboard: Provides an image suitable for displaying on a blackboard.
Game: Provides an image suitable for viewing games.
Cinema: Provides an image suitable for viewing movies.
Reset*2 Resets to the factory setting.
Contrast The higher the value, the greater the contrast. The lower the value, the lower
the contrast.
Brightness The higher the value, the brighter the picture. The lower the value, the darker
the picture.
Color*3 *4 The higher the value, the greater the intensity. The lower the value, the lower
the intensity.
Hue*3 *4 *5 The higher the value, the more greenish the picture becomes. The lower the
value, the more reddish the picture becomes.
Color Temp.*6 High/Middle/Low: The higher the value, the more bluish the picture
becomes. The lower the value, the more reddish the picture becomes.
Sharpness The higher the value, the sharper the picture becomes. The lower the value, the
softer the picture becomes.
Expert Setting
Gamma
Mode*1 *7 Graphics 1: Gamma correction to make halftones brighter. This setting is
suitable when projecting highly colorful images, such as photos, in a bright
place.
Graphics 2: Gamma correction to improve the reproduction of halftones.
Highly colorful images, such as photos, can be reproduced in natural tones.
Text: Improves back and white contrast. Suitable for images with lots of text
content.
Notes

18 The Screen Menu
The Screen Menu
The Screen menu is used to adjust the size, position and aspect ratio of the projected image for
each input signal.
Items Item descriptions
Aspect*1 Changes the aspect ratio of the projected image (page 20).
VPL-DX145/DX125:
When the computer
signal is input
4:3: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 16:9.
Full 1: Displays the image to fit the maximum projected image
size without changing the aspect ratio of the input signal.
Normal: Displays the image on the center position of the
projected image without changing the resolution of the input
signal or enlarging the image.
VPL-DX145/DX125:
When the video signal
is input
4:3: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 16:9.
Zoom: Zooms the center area of a projected image.
VPL-DW125: When
the computer signal is
input
4:3: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 16:9.
Full 1: Displays the image to fit the maximum projected image
size without changing the aspect ratio of the input signal.
Full 2: Displays the image to fit the maximum projected image
size changing the aspect ratio of the input signal.
Full 3: Displays the image to fit the maximum width or height, up
to 1280 × 720 pixels, without changing the aspect ratio of the
input signal.
Normal: Displays the image on the center position of the
projected image without changing the resolution of the input
signal or enlarging the image.
VPL-DW125: When
the video signal is
input
4:3: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size
with an aspect ratio fixed to 16:9.
Full: Displays the image to fit the maximum projected image size
changing the aspect ratio of the input signal.
Zoom: Zooms the center area of a projected image.

19
The Screen Menu
Adjustments and Settings Using a Menu
*1: • Note that if the projector is used for profit or for public viewing, modifying the original picture
by switching to the aspect mode may constitute an infringement of the rights of authors or
producers, which are legally protected.
• Depending on the input signal, setting items for aspect ratio or some other setting items cannot
be set in some cases, or changing the aspect ratio setting may have no effect.
• A part of the image may be displayed in black, depending on the setting item.
*2: Available when a computer signal is input from the RGB input connector (INPUT A).
*3: If the projected image includes large amount of black portion around it, the APA function will
not work properly and a part of the image may not be displayed on the screen and also optimum
image cannot be obtained, depending on the type of input signal. In this case, adjust the “Phase,”
“Pitch,” and “Shift” items manually.
*4: Available when a computer or a video signal is input from the RGB/YPBPRinput connector
(INPUT A).
Adjust Signal Adjusts the image of a computer signal. Use this item if the edge
of the image is cut, or is not displayed properly.
APA*2 *3 Automatically adjusts the projected image to an optimum quality
when you press the ENTER key (page 6).
Phase*2 Adjusts the dot phase of the display pixel and the input signal. Set
to the value where looks clearest.
Pitch*2 The higher the value, the wider the horizontal image elements
(pitch). The lower the value, the narrower the horizontal image
elements (pitch).
Shift*4 H (Horizontal): The higher the value, the farther right the image
is projected on the screen. The lower the value, the image farther
left.
V (Vertical): The higher the value, the farther up the image is
projected on the screen. The lower the value, the image farther
down.
Notes
Items Item descriptions

20 The Screen Menu
Aspect
VPL-DX145/DX125 *1: If you select “Normal,” the image is
projected in the same resolution as the
input signal without changing the aspect
ratio of the original image.
*2: If you select “4:3,” the image is projected
to fit the projected image size, regardless
of the aspect ratio of the image.
*3: Depending on the input signal, the
projected image may be projected as
illustrated below. In this case, select
“16:9.”
*4: Depending on the input signal, the
projected image may be projected as
illustrated below. In this case, select
“Zoom.”
Input signal Recommended
setting value and
projected image
Computer signal
4:3 Full1*1
16:9 Full1*1 *2
16:10 Full1*1 *2
Video signal
4:3 4:3*3
16:9 16:9*4