Sound Sation 4LEDKIT-PRO User manual

4LEDKIT-PRO
Compact 4 LED panel set
Please read this manual carefully and properly take care of it
USER MANUAL
Leggete questo manuale e conservatelo per future consultazioni
MANUALE UTENTE

Dear customer,
First of all thanks far purchasing a SOUNDSATION® product. Our mission is to satisfy
all possible needs of musical instrument and professional audio users offering a wide
range of products using the latest technologies.
We hope you will be satised with this item and, if you want to collaborate, we are
looking for a feedback from you about the operation of the product and possible
improvements to introduce in the next future. Go to our website www.soundsation-
music.com and send an e-mail with your opinion, this will help us to build instruments
ever closer to customer’s real requirements.
One last thing: read this manual before using the instrument, an incorrect operation
can cause damages to you and to the unit. Take care!
The SOUNDSATION Team
Gentile Cliente,
Grazie per aver scelto un prodotto SOUNDSATION®. La nostra missione è quella di
offrire ai nostri utenti una vasta gamma di strumenti musicali ed apparecchiature audio
e lighting con tecnologie di ultima generazione.
Speriamo di aver soddisfatto le vostre aspettative e, se voleste collaborare, sarem-
mo lieti di ricevere un vostro feedback sulla qualità del prodotto al ne di migliorare
costantemente la nostra produzione. Visitate il nostro sito www.soundsationmusic.
com ed inviateci una mail con la vostra opinione, questo ci aiuterà a sviluppare nuovi
prodotti quanto più vicini alle vostre esigenze.
Un’ultima cosa, leggete il presente manuale al ne di evitare danni alla persona ed al
prodotto, derivanti da un utilizzo non corretto.
Il Team SOUNDSATION

3
ENGLISH
4LEDKIT-PRO User manual
TABLE OF CONTENTS
1. INTRODUCTION.........................................................................................................6
1.1. Unpacking.................................................................................................................................................................6
1.2. Accessories...............................................................................................................................................................7
2. OVERVIEW..................................................................................................................7
3. MAIN FEATURES........................................................................................................7
4. INSTALLATION...........................................................................................................8
5. MAINS CONNECTIONS .............................................................................................9
6. DMX CONNECTION...................................................................................................9
6.1. DMX Terminator .....................................................................................................................................................9
7. REAR PANEL.............................................................................................................10
7.1. Control Panel .........................................................................................................................................................11
7.2. Pedal Board Control Panel................................................................................................................................12
8. FUNCTIONS MAP ....................................................................................................13
8.1. FUNCTIONS DESCRIPTION ..............................................................................................................................14
9. CHANNEL CHARTS..................................................................................................15
9.1. 6Ch Mode Chart...................................................................................................................................................16
9.2. 18Ch Mode Chart ................................................................................................................................................17
10. SPECIFICATIONS ......................................................................................................19
11. WARRANTY AND SERVICE .....................................................................................20
12. WARNING.................................................................................................................20

4
ENGLISH
4LEDKIT-PRO User manual
IMPORTANT SAFETY SYMBOLS
The symbol is used to indicate that some hazardous live terminals are
involved within this apparatus, even under the normal operating con-
ditions, which may be sufcient to constitute the risk of electric shock
or death.
The symbol is used in the service documentation to indicate that spe-
cic component shall be replaced only by the component specied in
that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
Denotes the apparatus is turned on
Denotes the apparatus is turned off
WARNING: Describes precautions that should be observed to prevent the danger
of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of
the apparatus.
To protect the environment, please try to recycle the packing material
as much as possible
The projector is for indoor use only, IP20. Use only in dry locations.
Keep this device away from rain and moisture, excessive heat, humid-
ity and dust. Do not allow contact with water or any other uids, or
metallic objects.
Don’t throw this product away just as general trash, please deal with
the product follow the abandon electronic product regulation in your
country.
TAKING CARE OF YOUR PRODUCT
fRead these instructions
fKeep these instructions
fHeed all warning
fFollow all instructions

5
ENGLISH
4LEDKIT-PRO User manual
1) Water / Moisture
The apparatus should be protected from moisture and rain and can not be used near
water; for example near a bathtub, a kitchen sink, a swimming pool, etc.
2) Heat
The apparatus should be located away from heat sources such as radiators, stoves or
other appliances that produce heat. Don not use it when maximum ambient tempera-
ture is higher than 40°C.
3) Ventilation
Do not block areas of ventilation opening. Failure to do could result in re. Always
install according to the manufacturer’s instructions.
4) Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside of the apparatus for
safety.
5) Power Cord and Plug
Protect power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus. Do not defeat the safety
purpose of the polarized or grounding-type plug. A polarized plug has two poles; a
grounding-type plug has two poles and a third grounding terminal. The third prong is
provided for your safety. If the provided plug does not t into your outlet, refer to an
electrician for replacement.
6) Power Supply
The apparatus should be connected to the power supply only of the type as marked on
the apparatus or described in the manual. Failure to do could result in damage to the
product and possibly the user. Unplug this apparatus during lightning storms or when
unused for long periods of time.
7) FUSE AND Electrical Connection
Always disconnect from the power source before servicing or replacing fuse and be
sure to replace with same fuse size and type. Cut off power before moving, repairing
and cleaning the unit. Improper electrical wiring may invalidate the product warranty.
To avoid electric shock, all xtures must be connected to circuits with a suitable ground.
Do not power on and power off the xture in a short time.
8) DMX connection
When use DMX controller, please make sure that there is no interference sources (e.g.
intercom, high frequency radio waves and radiation source).
9) Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzene or alcohol.

6
ENGLISH
4LEDKIT-PRO User manual
10) Servicing
Do not implement any servicing other than those means described in the manual. Refer
all servicing to qualied service personnel only. Only use accessories/attachments or
parts recommended by the manufacturer.
1. INTRODUCTION
Thank you for purchasing our 4LEDKIT-PRO. Enjoy your new equipment and make sure
to read this manual carefully before operation.
This user manual is made to provide both an overview of controls, as well as informa-
tion on how to use them.
1.1. Unpacking
Your 4LEDKIT-PRO was carefully packed in two cartons to ensure safe transport. Despite
this, we recommend you to carefully examine the package and its contents for any
signs of physical damage, which can occur during transport. Each unit has the following
parts:
1) PAR-BAR CARTON
f1 x T-Bar with 4 lightweight LED light PARs
f1 x Pedal board with 4 footswitch
f1 x Carrying bag
f1 x Cable for pedal board connection
f1 x IEC Power cord
f2 x Brackets for xing to the ground or on trusses.
f2 x Washers
f2 x Screw knobs
f1 x User manual
2) TRIPOD STAND CARTON
f1 x Tripod Stand
f1 x carrying bag
ATTENTION: Packaging cartons are not a toys! Keep out of reach of chil-
dren!!! Keep in a safe place the original packaging material for future use.
If anything damaged during transport, notify the shipper immediately and keep the
packing material for inspection. Again, please save the carton and all packing materials.
If the xture must be returned to the manufacturer, it is important that it is returned in
the original manufacturer box and packing. Please do not take any action without rst
contacting us.

7
ENGLISH
4LEDKIT-PRO User manual
1.2. Accessories
SOUNDSATION can supply a wide range of quality accessories that you can use with
your 4LEDKIT-PRO, like Cables, Splitters, DMX controllers, and a wide range of other
xtures.
All products in our catalogue has been long tested with this device, so we recommend
you to use Genuine SOUNDSATION Accessories and Parts.
Ask your SOUNDSATION dealer or check out our website www.soundsationmusic.com
for any accessories you could need to ensure best performance of the product.
2. OVERVIEW
When giving colors to your gigs passes through simplicity of use, portability and
the benets of modern LED technology, SOUNDSATION 4LEDKIT-PRO becomes the
reference to all musicians, DJs and entertainment operators. 4LEDKIT-PRO have been
designed to be all-in-one light systems with all accessories in a single package. It
includes tripod support with bag, pedal board for quick control of main functions, “T”
bar with carrying bag, integrated DMX-512 interface to allow remote control via DMX
controllers. Light emission technologies range from RGB combination of single-color
LEDs, to RGB 3in1, RGB 3in1 COB, and RGBW 4in1. Emission angles range from 16° and
26° beam effect to 90° wash effect for COB model.
3. MAIN FEATURES
f4 lightweight LED PARs, each of them coming with 4 High-brightness 10W LED
(16pcs 10W RGBW 4in1 LED in total)
f4 Operating Modes (Auto, Sound, Fixed Colors, DMX)
f50.000 hours long-life LED
fRGBW color mixing
fColor Strobe
fMaster/Slave synchronization
fDMX-512 protocol
fElectronic Dimmer 0-100%
fFoot controller
fCarrying soft-case
fTripod stand with carrying bag (Max height 2,5m)

8
ENGLISH
4LEDKIT-PRO User manual
4. INSTALLATION
SOUNDSATION 4LEDKIT-PRO can be installed on the oor, on the wall, ceiling or on a
truss.
WARNINGS:
A. It’s required the use of a safety wire (LW3-76A or LW4-76A sold separately) in
if the product is hanging on a wall, ceiling or on a truss.
B. Never leave the product swinging freely.
C. If the product is hanging on a wall, a ceiling or a truss, make sure that the
installation gear and / or the truss can hold a minimum load of 10 times the
weight of the device.

9
ENGLISH
4LEDKIT-PRO User manual
5. MAINS CONNECTIONS
Connect the device to the mains with the supplied power cord. When connecting the
power supply, please check that the supply voltage and frequency are the same as indi-
cated for the device. The correspondence of the wires is as follows:
Cable (EU) Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
The earth must to be connected! Pay attention to the safety! Before taking
into operation for the rst time, the installation has to be approved by an
expert.
6. DMX CONNECTION
DMX xtures are designed to receive data through a serial Daisy Chain. A Daisy Chain
connection is where the DATA OUT of one xture connects to the DATA IN of the next
xture. The order in which the xtures are connected is not important and has no effect
on how a controller communicates to each xture. Use an order that provides for the
easiest and most direct cabling.
3-Pin XLR
Pin 1: GND
Pin 2: DMX -
Pin 3: DMX +
OUTPUTINPUT
DMX use of 3-Pin XLR Connectors
DMX Termonator
Unit 1 Unit 2 Last Unit
DMX 512
Connect xtures using shielded 2-conductor twisted pair cable with 3-pin XLR male to
female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and
pin 3 is Data positive (S+).
CAUTION: Wires must not come into contact with each other; otherwise the
xtures will not work at all, or will not work properly.
6.1. DMX Terminator
DMX is a resilient communication protocol, however errors still occasionally occur.
In order to prevent electrical noise from disturbing and corrupting the DMX control

10
ENGLISH
4LEDKIT-PRO User manual
signals, a good habit is to connect DMX output of last xture in the chain to a DMX
terminator, especially over long signal cable runs.
The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor
connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then
plugged into the output socket on last projector in the chain. The connections are
illustrated below.
120ohm, 1/4 W
resistor
DMX Terminator
Complimentary signal cable can transmits signals to 20 unit xtures at most.
Signal amplier is a must to connect more xtures.
7. REAR PANEL
1
2
2 3 4 5 22678
9
10
1) IEC Socket with Fuse holder
Plug the power-cord into an AC socket properly congured for your particular model.
In case of fuse burn, to prevent the risk of re and damaging the unit, please use only a
spare of the recommended fuse type as described in the “10. SPECIFICATIONS” on page
19. Before replacing the fuse, make sure the unit turned off and disconnected from
the AC outlet.
2) DIN 8 pin CONNECTORS
There are four 8-pin DIN connectors to insert the related cables from the projectors.
3) METAL Housing
4) DIN 8 pin PEDAL-BOARD CONNECTOR
Connect the supplied 8-pin DIN cable from this connector to the bundled pedal board

11
ENGLISH
4LEDKIT-PRO User manual
that will be used to control the device as described in the “7.2. Pedal Board Control
Panel” on page 12.
5) CONTROL PANEL
This panel section has a 4x7 Segments display and 4 buttons to control all the device
functions. (For further details see “7.1. Control Panel” on page 11).
6) DMX INPUT (MALE SOCKET)
7) DMX OUTPUT (FEMALE PLUG)
8) BUILT IN MICROPHONE
9) PROJECTORS
10) SUPPORT FRAME
In the case of installation on the supplied tripod stand, this support frame is provided
wit a D36mm hole adapter, with two screw knobs for xing the device.
7.1. Control Panel
MENU/ESC UP DOWN ENTER
5
14
2 3
1) Menu/ESC Button
This button allows to put in stand-by the control panel and to escape from a selected
function without any saving.
2) UP Button
Using this button, it is possible to scroll-up the device’s functions and increase the func-
tion’s value.

12
ENGLISH
4LEDKIT-PRO User manual
3) DOWN Button
Using this button, it is possible to scroll-down the device’s functions and decrease the
function’s value.
4) ENTER Button
This button allows to save a new function’s value.
5) 4 x 7 SEGMENTS display
It shows the current function’s name or function’s value.
7.2. Pedal Board Control Panel
SOUNDSATION 4LEDKIT-PRO is equipped with a pedal board with 4 foot switches to
easily control some main functions.
AUTO
FOOT CONTROLLER
COLOR BLACKOUT
4LED KIT-PRO
SOUND
12 3 4
1) AUTO FOOTSWITCH
Activate one of the 3available AUTO Modes. The display on the Control Panel will
show: . The last digit (-) will indicate the AUTO mode number.
2) SOUND FOOTSWITCH
Activate one of the 5available SOUND Modes. The display on the Control Panel will
show: . The last digit will indicate the SOUND mode number.
3) COLOR FOOTSWITCH
Activate one of the 9available Pre-Set COLORS. The display on the Control Panel will
show: . The last digit will indicate the Pre-Set COLOR number.
4) BLACKOUT FOOTSWITCH
Turn OFF all the 4LEDKIT-PRO projectors.
The display on the Control Panel will show:

13
ENGLISH
4LEDKIT-PRO User manual
8. FUNCTIONS MAP
1
2
3
4
5
6
7
8

14
ENGLISH
4LEDKIT-PRO User manual
8.1. FUNCTIONS DESCRIPTION
All the 4LEDKIT-PRO functions are selectable by using the UP BUTTON and DOWN
BUTTON on the Control Panel as described in “7.1. Control Panel” on page 11.
Below is an explanation of the device’s functions.
1) DMX CHANNEL SELECTION
After the selection of function, by pressing ENTER button, it is possible to
select the desired DMX Channel in order to manage the device using a DMX controller.
Once the channel is selected, press the ENTER button to conrm the value.
The range of this parameter is A001 -> A512
2) AUTO MODE SELECTION
function allows to select one of the 3available (AUT1 -> AUT3) AUTO
Modes . After the selection, by pressing the ENTER button, a sub-menu will be shown
where you can change the speed of the selected AUTO mode.
The range of this parameter is SP-1 -> SP-9. Press the ENTER button to conrm.
3) SOUND MODE SELECTION
function allows to select one of the 5available (SOU1 -> SOU5) SOUND
Modes. After the SOUND Mode selection, by pressing the ENTER button, a sub-menu
will be shown where it is possible to regulate the Built In Microphone sensibility.
The range of this parameter is SC-1 -> SC-9. Press the ENTER button to conrm the
value.
4) CHASE MODE SELECTION
function allows to select one of the 5available (C 1 -> C 5) CHASE Modes
. After the selection, by pressing the ENTER button, a sub-menu will be shown where
you can change the speed of the selected CHASE Mode.
The range of this parameter is SP-1 -> SP-9. Press the ENTER button to conrm the
value.
5) DMX CHANNELS NUMBER CONFIGURATION
4LEDKIT-PRO can be congured with two channel modes in order to be managed by a
DMX controller. The function that allows the selection of the mode is .
The two possible modes are 6Ch and 18Ch. Press the ENTER button to conrm the
selected mode.

15
ENGLISH
4LEDKIT-PRO User manual
6) COLOR SELECTION
function allows to activate one of the 9available Pre-Set COLORS.
On the display will be shown the current color selected (CoL1 -> CoL9).
In this function in addition, it is possible to enter the sub-menu where there
are the following parameters:
fr 000....255 - Intensity of RED on basic white color.
fG 000....255 - Intensity of GREEN on basic white color.
fb 000....255 - Intensity of BLUE on basic white color.
fc 000....255 - Global intensity for color mixing.
7) SLAVE MODE
Using the function, it is possible to connect several units together and oper-
ate them in synchronized mode:
fUse DMX cables to connect two or more units together from the DMX OUT connec-
tor to the DMX IN connector.
fThe rst unit is MASTER and all the connected units must be set as SLAVE by press-
ing the ENTER button (SLAU -> SLA)
fOperate the Master unit in Automatic mode (AUTo), Macro Color (CoLo),Musical
(SOUn) or Chase (CHAS) to operate the entire system. The entire chain of Slave units
will act as the Master unit.
8) SOFTWARE VERSION
By pressing the ENTER button after selecting the function, the display will
show the current software version.
9. CHANNEL CHARTS
As already explained, 4LEDKIT-PRO can be managed by a DMX controller using one of
the 2 possible channel modes:
f6Ch (Please refer to “9.1. 6Ch Mode Chart” on page 16)
f18Ch (Please refer to “9.2. 18Ch Mode Chart” on page 17)

16
ENGLISH
4LEDKIT-PRO User manual
9.1. 6Ch Mode Chart
CHANNEL VALUE FUNCTION
CH1 0 - 255 Red (0% - 100%)
CH2 0 - 255 Green (0% - 100%)
CH3 0 - 255 Blue (0% - 100%)
CH4 0 - 255 White (0% - 100%)
CH5 0 - 255 Strobe(0~20HZ) & Auto Speed (Slow to Fast)
CH6
0 - 10 Null
11 - 19 COLOR FADE MODE 1
20 - 30 COLOR FADE MODE 2
31 - 39 COLOR FADE MODE 3
40 - 49 COLOR FADE MODE 4
50 - 59 Color Chase1
60 - 69 Color Chase2
70 - 79 Color Chase3
80 - 89 Color Chase4
90 - 99 Color Chase5
100 - 109 Color Chase6
110 - 119 Color Chase7
120 - 129 Color Chase8
130 - 139 Color Chase9
140 - 149 Color Chase10
150 - 159 Color Chase11
160 - 169 COLOR MACRO MODE 1
170 - 179 COLOR MACRO MODE 2
180 - 189 COLOR MACRO MODE 3
190 - 199 COLOR MACRO MODE 4
200 - 209 COLOR MACRO MODE 5
210 - 219 Sound_1
220 - 229 Sound_2
230 - 239 Sound_3
240 - 249 Sound_4
250 - 255 Sound_5

17
ENGLISH
4LEDKIT-PRO User manual
9.2. 18Ch Mode Chart
CHANNEL VALUE FUNCTION
CH1 0 - 255 Red (0% - 100%) PAR1
CH2 0 - 255 Green (0% - 100%) PAR1
CH3 0 - 255 Blue (0% - 100%) PAR1
CH4 0 - 255 White (0% - 100%) PAR1
CH5 0 - 255 Red (0% - 100%) PAR2
CH6 0 - 255 Green (0% - 100%) PAR2
CH7 0 - 255 Blue (0% - 100%) PAR2
CH8 0 - 255 White (0% - 100%) PAR2
CH9 0 - 255 Red (0% - 100%) PAR3
CH10 0 - 255 Green (0% - 100%) PAR3
CH11 0 - 255 Blue (0% - 100%) PAR3
CH12 0 - 255 White (0% - 100%) PAR3
CH13 0 - 255 Red (0% - 100%) PAR4
CH14 0 - 255 Green (0% - 100%) PAR4
CH15 0 - 255 Blue (0% - 100%) PAR4
CH16 0 - 255 White (0% - 100%) PAR4
CH17 0 - 255 Strobe(0~20HZ) & Auto Speed (Slow to Fast)
CH18
0 - 10 Null
11 - 19 COLOR FADE MODE 1
20 - 30 COLOR FADE MODE 2
31 - 39 COLOR FADE MODE 3
40 - 49 COLOR FADE MODE 4
50 - 59 Color Chase1
60 - 69 Color Chase2
70 - 79 Color Chase3
80 - 89 Color Chase4
90 - 99 Color Chase5
100 - 109 Color Chase6
110 - 119 Color Chase7
120 - 129 Color Chase8
130 - 139 Color Chase9
140 - 149 Color Chase10

18
ENGLISH
4LEDKIT-PRO User manual
18CH
150 - 159 Color Chase11
160 - 169 COLOR MACRO MODE 1
170 - 179 COLOR MACRO MODE 2
180 - 189 COLOR MACRO MODE 3
190 - 199 COLOR MACRO MODE 4
200 - 209 COLOR MACRO MODE 5
210 - 219 Sound_1
220 - 229 Sound_2
230 - 239 Sound_3
240 - 249 Sound_4
250 - 255 Sound_5

19
ENGLISH
4LEDKIT-PRO User manual
10. SPECIFICATIONS
Electrical
Voltage 110V ~ 240V 50-60HZ
Power consumption 180W
Fuse 2A
Driver electric current 500mA
Light Source
LED 16 x 10W (4in1)
Illuminance 2642 Lux @ 2 mt
Colors RGBW Color Mixing
Beam Angle 15°
Led Life 50000 Hours
Control Mode
DMX512 6CH/18CH
Master/slave
Fixed Colors
Sound Active
Auto
Chase
Connectors
1 x IEC Socket
4 x DIN 8 pin ( Projectors connection)
1 x DIN 8 pin ( Pedal Board connection)
1 x DMX Input
1 x DMX Output
Bundled Accessories
1 x Tripod Stand with Carrying Bag
1 x Pedal Board
1 x Soft Carrying Bag (WxHxD - 960 x 140 x 300 mm)
1 x DIN 8 Pin Cable
1 x IEC Power Cord
2 x Brackets
2 x Washers
2 x Screw Knobs
1 x Owner’s Manual
Packaging 2 Cartons Tripod Stand Carton
PAR-BAR Carton
Dimensions
Tripod Stand (WxHxD) 1050 x 2500 x 900 mm (Open)
Tripod Stand Packing (WxHxD) 1250 x 130 x 150 mm
PAR-BAR (WxHxD) 880 x 80 x 220 mm
PAR-BAR Packing (WxHxD) 1020 x 180 x 400 mm
Weights
Tripod Stand 4,6 Kg
Tripod Stand Packing 4,8 Kg
PAR-BAR 5,6 kg
PAR-BAR Packing 10,4 Kg
Environment & safety Stock Dry Place
Working indoor temperature –20°C ~+ 40°C

20
ENGLISH
4LEDKIT-PRO User manual
11. WARRANTY AND SERVICE
All SOUNDSATION products feature a limited two-year warranty. This two-year warranty is specic
to the date of purchase as shown on your purchase receipt.
The following cases/components are not covered from the above warranty:
• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modication of the product effected by the user or a third party
SOUNDSATION shall satisfy the warranty obligations by remedying any material or manufacturing
faults free of charge at SOUNDSATION’s discretion either by repair or by exchanging individual
parts or the entire appliance. Any defective parts removed from a product during the course of a
warranty claim shall become the property of SOUNDSATION.
While under warranty period, defective products may be returned to your local SOUNDSATION
dealer together with original proof of purchase. To avoid any damages in transit, please use the
original packaging if available. Alternatively you can send the product to SOUNDSATION SERVICE
CENTER – Via Enzo Ferrari , 10 – 62017 Porto Recanati - Italy . In order to send a product to service
center you need an RMA number. Shipping charges have to be covered by the owner of the prod-
uct.
For further information please visit www.soundsationmusic.com
12. WARNING
PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only
This symbol indicates that this product is not to be disposed of with your household waste, ac-
cording to the WEEE Directive (2202/96/EC) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized one-
for-one basis when you buy a new similar product or to an authorized collection site for recycling
waste electrical and electronic equipment (WEEE).
Improper handling of this type of waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that are generally associated with EEE.
At the same time, your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please
contact your local city ofce, waste authority, approved WEEE scheme or your household waste
disposal service.