Southern Enterprises HZ349300TX User manual

1
HZ349300TX Shelf- Black
HZ349400TX Shelf- White
Assembly Instructions
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com
PO#

2
Tool List: 3/16" drill bit, drill, tape measure and pencil
Shelf
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A Quantity
Of 2
plastic anchor
Dia: 1/4” x 1-3/16”L
B Quantity
Of 10
screw
Dia: 5/32” x 1-1/2”L
C Quantity
Of 12
sticker cover
D
Quantity
of 1
leveler
E Quantity
Of 4
screw
Dia: 1/4“ x 2”L
F Quantity
Of 1
allen wrench
G Quantity
Of 1
back board
H Quantity
Of 2
shelf 1
I Quantity
Of 4
shelf 2
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096
Assembly Tool Required
No.2 Phillips Screwdriver
Not Included

3
Figure 1
Connect shelves (I) and shelves (H)
to back board (G) with screws (B).
Tighten screws with phillips
screwdriver.
Figure 2
Co
ver screw holes with sticker
covers (C) as shown in figure
2.
Shelf
Assembly Instructions

4
NOTE: NO DRILLED HOLE OR PLASTIC ANCHOR
REQUIRED WHEN MOUNTING TO WOOD WALL.USE
SCREW ONLY. WE DO NOT SUPPLY HARDWARE FOR
MOUNTING ON CONCRETE WALLS
Figure 3
Find a desired location and mark two
locations for the screws.
One screw (for each unit) must be
attached directly into a wall stud. Wall
anchor is not needed when mounting
to wall stud.
Drill one marking 3/16" hole (for each
unit).
Insert plastic anchor (A) into the hole
on wall as shown, you will need a
hammer when doing this.
Using the phillips head screwdriver,
install one screw (B) into the anchor
(A) and the other screw installed into
the stud. Turn the screws (B) until
there is a gap of approximately 13 mm
between the head of the screw and
the wall as shown.
Figure 4
Hang assembled unit onto the screws
(B) and verify the shelf is resting
securely on the mounting screws (B).
Use a leveler to insure product is level.
Now you shelf is ready to use.
"
T
he hole
measurement
s
o
n
wall must match with the
hole measurements on back
of the unit"

5
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at servi[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction. Please contact the retailer that
you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity
Needed
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Parts Replacement Form

6
CAUTIO
Max shelf load capacity is achieved by mounting screw into studs or cement
walls.
If mounting to sheet rock (cavity wall) it is advisable to mount at least one screw
(without anchor) directly to a wall stud or studs. owever do not leave either end of
mounting bracket unsupported by at least one anchor. For hollow wall mounting you
can use any of the holes in the back plate to suit where you require the mounting
screws positioned.