Southern Enterprises KA327700TX User manual

KA327700TX
MARTINVILLE KITCHEN
CART - White
Assembly Instructions
For assistance with assembly contact：
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com

MARTINVILLE KITCHEN CART - White
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Using a screw that is too long
will cause damage. efore beginning assembly, separate each type of screw.
Carefully study the Screw diagrams below.
You may receive extra hardware with your unit.
No. Description Qty No. Description Qty
1 Table Top 1 pc 9 Front Apron 1 pc
2 Side Frame (R) 1 pc 10 Bottom Panel 1 pc
3 Side Frame (L) 1 pc 11 Door 2 pcs
4 Upper Back Panel 1 pc 12A Drawer Front 1 pc
5 Back Apron 1 pc 12B Drawer Side Apron (R) 1 pc
6 Back Panel 3 pcs 12C Drawer Side Apron (L) 1 pc
7A Shelf (R) 2 pcs 12D Drawer Back Panel 1 pc
7B Shelf (L) 1 pc 12E Drawer Bottom Panel 1 pc
8 Center Panel 1 pc 13 Towel Bar 1 set

A Quantity
of 11
Long Bolt ( M6 X 50 )
B Quantity
of 4
Barrel Nut
C Quantity
of 3
Small Bolt ( M6 X 40 )
D Quantity
of 2
Spring Washer
E Quantity
of 2
Flat Washer
F Quantity
of 4
Cam Bolt
G Quantity
of 4
Cam Lock
H Quantity
of 12
Metal Pin
I Quantity
of 3
Bar Handle
J Quantity
of 6
Handle Screw X 22mm
K Quantity
of 4
Door Spring
L Quantity
of 1
Allen Key
M Quantity
of 1
H-Profile
N Quantity
of 8
Wood Screw X 32mm

O Quantity
of 11
Wood Button
P Quantity
of 2
Castor With Lock
Q Quantity
of 2
Castor Without Lock
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096.
Assembly Tool Required
No.2 Phillips Screwdriver (Not Included)

Martinville Kitchen Cart - White
Assembly Instructions
Figure 1
Attach Cam Bolts (F) into Table
Top (1) and Bottom Panel (10)
as shown. Tighten using
Screwdriver.
Figure 2
Attach Side Frame (R) (2) to
Table Top (1) with Long Bolts
(M6x50) (A). Tighten using Allen
Wrench (L) provided.
Attach Back Apron (5) to the unit
with Long Bolts (M6x50) (A).
Tighten using Allen Wrench (L)
provided.
Slide Upper Back Panel (4) into
groove between the aprons as
shown.

Figure 3
Insert Center Panel (8) onto the
attached Cam Bolts (F) on the
unit and secure using Cam
Locks (G). Tighten Cam Locks
(G) using Screwdriver.
Attach Front Apron (9) to Center
Panel (8) as shown by using
Short Bolt (M6 X 40) (C).
Tighten using Allen Wrench (L)
provided.
Slide 1 Pc Back Panel (6)
between Side Frame (2) and
Centre Panel (8).
Connect 2pcs of Back Panels
(6) with H-Profile (M) as shown.
Then slide into the grooves of
Centre Panel (8) and Back
Apron (5) as shown.
Figure 4
Attach Side Frame (L) (3) to the
unit by inserting Long Bolts
(M6x50) (A) into Top Panel (1).
Tighten using Allen Wrench (L)
provided.
Place Bottom Panel (10) onto
the unit and align the Cam Bolt
(which assembled in Figure 1) to
the Center Panel (8). Tighten
using Cam Locks (G) using
Screwdriver.
Secure Bottom Panel (10) to
Side Frames using Long Bolts
(M6 X 5) (A) and insert Barrel
Nut (B) into Bottom Panel (10).
Note: Align the hole of the
Barrel Nuts towards bolts
direction. Tighten using Allen
Wrench (L) provided

Figure 5
Attach Towel Bar (13) onto the
unit as shown with Short
Bolts (M6 X 40) (C), Spring
Washers (D) and Flat Washers
(E). Tighten using Allen Wrench
(L) provided.
Attach Castors With Lock (P)
and Castors Without Lock (Q)
as shown.
Figure 6
Insert Metal Pins (H) into the
unit as shown.
Place Shelves (R) (7A) and
Shelf (L) (7B) as shown.

Figure 7
Attach Drawer SideApron (R)
(12B) and Drawer Side Apron
(L) (12C) to Drawer Front (12A)
as shown. Tighten using Wood
Screw (N) with Screwdriver.
Slide Drawer Bottom Panel
(12E) into assembled unit.
Place the Drawer Back Panel
(12D) onto assembled unit.
Tighten using Wood Screws (N)
with Screwdriver.
Tighten Bar Handle (I) and
Handle Screw (J) with
Screwdriver.
Figure 8
Insert Door Springs (K) into
Doors (11) as shown. Place the
doors onto the assembled unit
by insert Door Spring into
corresponding holes on Bottom
Panel (10) then slide in the top
Door Springs into the
corresponding holes on Front
Apron (9).
Attach Bar Handle (I) and
Handle Screws (J) using
Screwdriver.
Insert Wood Buttons (O) to
cover all the holes for Bolts as
shown.
Now your kitchen cart is ready
to use

Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019