Southworth DANDY LIFT User manual

Owner’s Manual
DANDY LIFT
May 2017
Southworth Products Corp
P.O. Box 1380, Portland, Maine 04104-1380
For model numbers UDL-150, UDL-250, UDA-350W, UDA-500 & UDA-800,
this manual is for Serial number L-248493 and up,
and for machines manufactured in September 2011 and newer.
For older machines, contact Southworth Parts Department.
Model # ____________________
Serial # ____________________
Placed in Service ____________
Distributed by Ergonomic Partners
Email: [email protected]
Web: www.ergonomicpartners.com
PH: 314-884-8884 | FAX: [phone]

2NEW STYLE DANDY LIFT OWNER'S MANUAL
Please note: This manual was current at the time of printing. To obtain the latest, most
updated version, please contact Southworth’s Customer Service Department or go to
our website: www.SouthworthProducts.com, under the Parts & Service tab you will
nd a complete list of current owner’s manuals to print.

NEW STYLE DANDY LIFT OWNER'S MANUAL 3
Contents
RESPONSIBILITY OF OWNERS AND USERS..........................................Page 4
SAFETY................................................................................................................ 5
INTRODUCTION ................................................................................................. 6
SPECIFICATIONS ............................................................................................. 9
OPERATING INSTRUCTIONS ......................................................................... 10
Raise/Lower........................................................................................... 10
Loading/Unloading................................................................................. 10
INSPECTION & MAINTENANCE ...................................................................... 11
ILLUSTRATED PARTS LIST ............................................................................. 15
ORDERING REPLACEMENT PARTS ............................................................... 24
WARRANTY .................................................................................. Back of manual
List of Figures
Fig. N1-1 Platform............................................................................................ 16
Fig. N1-2 Scissor Device (UDL-250, UDA-500 & UDA-800) ........................... 16
Fig. N1-2' Scissor Device (UDA-350W)............................................................ 17
Fig. N1-4 Handle Assembly ............................................................................. 17
Fig. N1-5 Jack Assembly ................................................................................. 18
Fig. N1-6 Caster .............................................................................................. 18
Fig. N1-7 Parking Lock .................................................................................... 18
Fig. N1-8 Release Lever Assembly ................................................................. 19
Fig. N1-9 Jack Pedal Assembly ....................................................................... 20
Fig. S-1 Platform............................................................................................ 21
Fig. S-2 Scissor Device (UDL-150) ............................................................... 21
Fig. S-4 Handle Assembly (UDL-150) ........................................................... 21
Fig. S-5 Jack Assembly (UDL-150) ............................................................... 22
Fig. S-6 Caster (UDL-150)............................................................................. 22
Fig. S-7 Parking Lock (UDL-150) .................................................................. 22
Fig. S-8 Release Lever Assembly (UDL-150) ............................................... 23
Fig. S-9 Jack Pedal Assembly (UDL-150) ..................................................... 23
Exclusively developed hydraulic jack has excellent reliability and durability allowing
it to last for about 400,000 strokes.
Serial numbers and manufactured date which marked on die on each brass plate
are registered in manufacture’s book. The number and date show individual identity
and please keep the record prior to use the unit.

4NEW STYLE DANDY LIFT OWNER'S MANUAL
Responsibility of Owners and Users
Inspection and Maintenance
The device shall be inspected and maintained in proper working order in accordance with
Southworth’s owner’s manual.
Removal from Service
Any device not in safe operating condition such as, but not limited to, excessive leakage,
missing rollers, pins, or fasteners, any bent or cracked structural members, cut or frayed
electric, hydraulic, or pneumatic lines, damaged or malfunctioning controls or safety devices,
etc. shall be removed from service until it is repaired to the original manufacturer’s standards.
Deection
It is the responsibility of the user/purchaser to advise the manufacturer where deection may
be critical to the application.
Repairs
All repairs shall be made by qualied personnel in conformance with Southworth’s instruc-
tions.
Operators
Only trained personnel and authorized personnel shall be permitted to operate the equip-
ment.
Before Operation
Before using the device, the operator shall have:
•Read and/or had explained, and understood, the manufacturer’s operating instructions
and safety rules.
•Inspected the device for proper operation and condition. Any suspect item shall be
carefully examined and a determination made by a qualied person as to whether it
constitutes a hazard. All items not in conformance with Southworth’s specication shall
be corrected before further use of the equipment.
During Operation
The device shall only be used in accordance with this owner’s manual.
•Do not overload.
•Ensure that all safety devices are operational and in place.
Modications or Alterations
Modications or alterations to any Southworth industrial positioning equipment shall be made
only with written permission from Southworth.

NEW STYLE DANDY LIFT OWNER'S MANUAL 5
SAFETY ALERT SYMBOLS AND SIGNAL WORDS
The safety of all persons operating, maintaining, repairing, or in the vicinity of this equipment is
of paramount concern. This is a powerful machine with moving parts, and is capable of causing
personal injury if proper precautions are not taken. Therefore, throughout this manual, certain
hazards have been identied which may occur in the use of the machine, and there are appropriate
instructions or precautions which should be taken to avoid these hazards. In some cases, there
are consequences which may occur if instructions or precautions are not followed. Below are
the symbols and signal words along with their denitions referenced from ANSI Z535.4 - Product
Safety Signs and Labels.
Safety Alert Symbols
These are the safety alert symbols. They are used to alert you to potential physical injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury or
death.
For use with DANGER signal word
(Red Background)
For use with WARNING signal word
(Orange Background)
For use with CAUTION signal word
(Yellow Background)
Signal Words
The meaning of different signal words as dened by ANSI Standard Z535.4 indicates the
relative seriousness of the hazardous situation.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a
hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE is used to address practices not related to per-
sonal injury.
(Red Background)
(Orange Background)
(Yellow Background)
(Blue Background)
SAFETY
INSTRUCTIONS
SAFETY INSTRUCTIONS (or equivalent) signs indicate
safety-related instructions or procedures.
(Green Background)

6NEW STYLE DANDY LIFT OWNER'S MANUAL
PRIOR TO OPERATING THE LIFT:
The UD Dandy Lift is designed to provide safe operation. By following these
safety rules, the operator will avoid injury to him/her self or others and also
damage to the Dandy Lift, other equipment or structures.
In order to ensure safe and efcient use, the operator should fully familiarize
himself with the contents of this manual prior to handling the unit. Also refer to
any precautionary labeling on the machine for guidance as you do the work.
WARNING
1. Keep non-authorized personnel away from the unit during operation.
2. Do not sit, stand or ride on the tabletop.
3. Do not load with more than the rated capacity.
4. Avoid any protrusion beyond the edge of the platform; load should always
be centered.
5. Keep hands or feet clear at all times.
6. Avoid rapid lowering of the platform while loaded.
7. The platform must be lowered when the unit is being transported.
8. During the loading/unloading operation, do not release parking brake.
9. Do not raise/lower the platform on a sloped or uneven surface.
For safe and efcient use of the unit, lubrication and servicing is necessary. At
initial start up, lubricate all required parts in accordance with lubrication section.
Maintenance and adjustment work must be performed while lift is not loaded,
and use an appropriate support to avoid accidental lowering. This support is
always recommended when working on a lift.
While performing maintenance do not work
on a raised lift. Lay the lift on its side when
working on the Dandy Leveler

NEW STYLE DANDY LIFT OWNER'S MANUAL 7
GENERAL INFORMATION & OPERATION
UDL-150, UDL-250, UDA-350W, UDA-500, UDA-800
A.The lift is packed in a cardboard box. Assembling of the handle with lift-lowering lever and
jack up pedal is required.
WARNING:
Assembly work must be done a on a at surface.
Wheels must be chocked to prevent accidental rolling of the unit.
To complete assembly of the lift:
1. Remove nuts and spring washers from the end of handle and insert the handle and
lowering lever rod simultaneously into hole on platform and frame. If rod end of lower-
ing lever slips out of the connecting sleeve or wedge of rod end does not hold in the
connecting sleeve, adjustment may be required. Tighten handle and lowering lever
using removed nuts and washers.
B. If air enters the hydraulic pump during transportation or in storage, lift may not raise even
when the pedal is rst pumped. In this case, place the unit in the normal position and push
the pedal all the way down (approximately ten times). This should clear the trapped air from
the self-bleeding system. Check to see that the jack is functioning properly.
C. Parking brake (oor lock) will require adjustment. Adjust the contact shoe so that you can
see it make contact with the oor with some force and then make sure it can still be released
without difculty.

8NEW STYLE DANDY LIFT OWNER'S MANUAL
General View of UDL-150, UDL-250, UDA-500, UDA-800 and UDA-350W
2. Assembly
A) Please take out, handle assembly and Jack pedal.
B) Remove hexagon bolt and nylon nut from Jack Pedal. Then put the Jack Pedal in to
Jack Pedal receiver. (Fig. 2)
C) Please remove nut and spring washer and then put in handle assembly to bottom frame.
(Fig. 3) Then the Release Lever Rod will go to right side of crank. (Fig. 4)

NEW STYLE DANDY LIFT OWNER'S MANUAL 9
MODEL UDL-150 UDL-250 UDA-500 UDA-800 UDA-350W
CAPACITY – lb. (kg.) 330 (150) 550 (250) 1100 (500) 1760 (800) 770 (350)
PLATFORM LOWERED
HEIGHT – inches (mm)
8.3 (210) 9.5 (245) 11.8 (300) 13.0 (330) 13.6 (345)
VERTICAL TRAVEL – inches
(mm)
20.7 (525) 22.2 (565) 24.8 (630) 27.2 (690) 36.2 (920)
PLATFORM RAISED HEIGHT –
inches (mm)
29.0 (735) 31.8 (810) 36.6 (930) 40.1 (1020) 49.8 (1265)
HANDLE HEIGHT – inches
(mm)
35.0 (885) 36.4 (925) 37.9 (965) 38.1 (970) 37.9 (965)
PLATFORM W x L – inches
(mm)
17.7 x 28.0
(450 x 710)
19.7 x 31.5
(500 x 800)
23.6 x 35.8
(600 x 910)
23.6 x 39.4
(600 x 1000)
23.6 x 35.8
(600 x 910)
OVERALL W x L – inches (mm) 17.7 x 32.8
(450 x 875)
19.7 x 36.6
(500 x 930)
23.6 x 42.1
(600 x 1070)
23.6 x 45.8
(600 x 1165)
23.6 x 42.5
(600 x 1080)
FOOT PEDAL STROKES TO
ELEVATE
15 20 45 55 45
FOOT PEDAL FORCE
REQUIRED – lb. (kg)
77.0 (35) 52.8 (24) 59.4 (27) 88.0 (40) 66.0 (30)
CASTERS FRONT 4” RIGID 4” RIGID - HD 5” RIGID 6” RIGID
URETHANE
5” RIGID
CASTERS REAR 4” SWIVEL 4” SWIVEL - HD 5” SWIVEL 6” SWIVEL
URETHANE
5” SWIVEL
PARKING LOCK/
FLOOR LOCK
YES YES YES YES YES
COLOR – PLATFORM/FRAME BLUE/BLUE ORANGE/BLUE YELLOW/BLUE GRAY/BLUE YELLOW/BLUE
TARE WEIGHT – lb. (kg) 85.8 (39) 118.8 (54) 193.6 (88) 250.8 (114) 231.0 (105)
SPECIFICATIONS
Note: Casters are rubber except where noted. Specications are subject to change without notice.

10 NEW STYLE DANDY LIFT OWNER'S MANUAL
Operation
Raise/Lower
CAUTION:
Lock parking brake securely. Do not raise/lower the platform on a sloped surface.
To raise: Pump jack pedal repeatedly.
NOTE: If the platform did not lift up properly, adjustment must be made in accordance with the inspec-
tion and maintenance section.
WARNING:
Keep hands or feet clear of the platform and the frame.
To lower: Turn lowering lever slowly in a clockwise direction. As soon as the platform starts down, do
not turn the lever more - maintain as is. The platform will continue lowering smoothly. The lowering
operation must be made slowly. By turning the lever, lowering speed can be adjusted.
NOTE: When load is on the platform, turn lever only the minimum amount to prevent rapid decent of
the platform. When the platform is empty, turn lever fully.
CAUTION:
Adjust stopper bolt when lift lowers too rapidly.
WARNING:
Keep hands or feet clear of the platform and the frame.
To maintain the platform at an intermediate point:
•The platform stops when pumping up pedal is stopped.
•When the lowering lever is released, the platform stops lowering and will maintain the position.
Loading/Unloading
CAUTION:
Do not allow load to overhang the edge of the platform.
Do not load more than specied capacity.
Parking Lock:
1. Parking brake (oor
lock) must be actu-
ated during parking
and lifting or lowering
of the platform.

NEW STYLE DANDY LIFT OWNER'S MANUAL 11
WARNING:
Floor lock (parking brake) is xed to prevent shoe from falling off during shipment. Do
not actuate as is. The following adjustments must be made as soon as the unit is as-
sembled.
2. Adjustment of the show on the parking brake
• Adjustment work must be done on at surface.
•Step on lock lever until it clicks actuating the brake.
• Screw shoe down by rotating it in a clockwise direction so that it touches the oor.
•Step on release lever to release the brake. Then rotate the shoe clockwise an additional
two turns to provide rm contact with the oor.
NOTE: By doing the above adjustments, shoe will compress by 1/8", assuring rm contact
with oor. If perfect braking is not achieved, repeat above adjustment.
Required pushing force for lock lever will increase, but braking effect will increase.
CAUTION:
Make sure oor lock is set during lifting or parking.
INSPECTION AND MAINTENANCE
UD Dandy Lifts do not require special maintenance, other than lubrication and periodic in-
spection. Inspection and maintenance should be made in accordance with the following
procedure for smooth and efcient operation.
CAUTION:
During lubrication, inspection and maintenance the platform must be empty.
WARNING:
If the platform needs to be raised for access to lubrication points, the unit should be
laid over on its side. Do not put your hands into a raised lift.
NOTE: The following are recommended as support and must be xed to the frame using
adhesive tape. Supports of the following size are recommended:
Width (in.) Length (in.)
UDL-150 3/4 x 3/4 11
UDL-250 3/4 x 1-1/2 12
UDA-350W 3/4 x 1-1/2 9
UDA-500 3/4 x 1-1/2 14
UDA-800 3/4 x 1-1/2 15

12 NEW STYLE DANDY LIFT OWNER'S MANUAL
A. Lubrication
Lubrication must be made in accordance with the following table:
Part Lubrication Material Fig. & Item No. To be referred
Rail (Frame) Grease N1-3*(S-3)
Roller (of Jack Lever) Grease (Grease
Nipple)
N1-9-12 (S-9-12)
Hinge on Scissor Machine Oil N1-2-1 (S-2-1-1)
Stay Machine Oil N1-2-4 (S-2-4)
Lifting-up Box (moving part) Machine Oil N1-2-1-2 (S-2-1-2) N1-2-3
Parking Lock Machine Oil N1-7* (S-7)
Lowering Lever (moving part) Machine Oil N1-8* (S-8)
Jack Pedal Grease, One (1)
(Grease Nipple)
N1-9-4 (S-9-2)
Other Contacting and Sliding
Area
Grease/Machine Oil
Jack Oil EP-32 or Equivalent
*( ) Is to be applied to UDL-150 Only
B. Inspection and Maintenance
Prior to use of the unit, check for any damage, deformation or cracks on the body.
NOTE: During inspection, the platform must be empty.
Remove foreign substance on scissors guide from the frame and rail.
• Check lifting performance of the platform in accordance with provision of operation.
• Check stopping performance at any desire height.
• Check lowering speed and smooth action of the lowering lever.
C. Adjustment
1. Malfunctioning up/down of the platform.
If the platform does not lift up or hold in any position even while jack is pumped.
• Air is in the jack unit
To bleed jack unit: Pump for three seconds and repeat a few times, then keep the unit
as is for about ten minutes. If air bubbles are not purged yet, repeat above adjustment
once more.
• Jack valve does not close perfectly
Valve on jack will not be closed perfectly. In this case, adjustment is required in accor-
dance with the procedure on the next page:

NEW STYLE DANDY LIFT OWNER'S MANUAL 13
For UDL-150, UDL-250, UDA-350W, UDA-500 and UDA-800
Loosen nut on connecting rod-1 and turn part (A), shown in right gure, in counter-
clockwise direction one turn.
Tighten the nut preventing turn of above (A).
Check for normal raising and lowering of the platform by pushing pedal.
If the above adjustment does not result in normal operation, repeat once more.
If the above adjustment does not result in normal operation, check for problem in other
parts.
2. Adjustment of lowering speed of the platform.
Incase the speed is abnormal, adjustment is required as follows:
•To take off the R-pin of center rod and washer.
•To adjustment release of release elver rod. To change the degree of release lever rod.
The right one is perpendicular with release lever.
•After adjustment, to assemble from center rod, washer to R-pin.

14 NEW STYLE DANDY LIFT OWNER'S MANUAL
D. Removing Scissor Assembly
1. Raise table up to maximum height and insert a maintenance support in scissor guide.
2. Loosen and remove screw (P/N 0218825) from lift box.
3. Remove a support from scissor guide and lower platform to lowest position using lower-
ing lever. Then raise platform again by hand as high as possible. Supporting both front
and rear edges as shown in above sketch. Them insert longer support, which are used
in above 1., to both front and rear scissor guide and x these using tape to prevent ac-
cidental lowering platform. (Refer to above sketch).
4. This connecting rod-2 and -3 by removing “R” pin (P/N 0340808) from the end of con-
necting rod-2 of lowering lever assembly.
5. Prior to removing jack, remove jack lever with following sequence:
a) Remove retaining screw(P/N 0212410), For UDL-150, remove ring “C” (P/N 0321601)
b) Draw out shaft (P/N ND140061), (P/N NA410082 for UDL-150)
c) Remove jack lever (P/N ND410011 or NB41001J, (P/N UNA401010 for UDL-150)
6. The above disconnects the jack from all connected linkages. Then the jack can be re-
moved by loosening mounting bolts of jack.
7. Reverse the above sequence for installation of jack.

NEW STYLE DANDY LIFT OWNER'S MANUAL 15
ILLUSTRATED PARTS LIST
For models UDL-250, UDA-500, UDA-800 and UDA-350W, refer to Figure 1 (item N) illustra-
tion and part number against Figure 2 (item S) for UDL-150.
To place your parts order, both model and serial number must be specied together with
name of each parts and required quantity.
For example:
Model No. Serial No. Item No. Name & (P/N) Quantity
UDA-500 N-6-1 Front caster
(P/N 38WK 125R
1

16 NEW STYLE DANDY LIFT OWNER'S MANUAL
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Platform 1
-1 Platform Plate 1 NB201010 ND201010 NE201010 NC201010
-2 Screw & Nut
Washer, Spring
4
4
0218820
0980856
0218825
0980853
0218825
0980853
0218820
0980853
-3 Plastic tting for Stay 2 ND391032 ND391032 ND391032 ND391032
Fig. N1-1 Platform
Item No Description Qty UDL-250 UDA-500 UDA-800
Scissor Device 1
-1-1 Scissor (Outer)
Scissor (Inner)
Pin, Pivot
1
1
NB310012
NB320012
NB370000
ND310011
ND320010
ND340070
NE310010
NE320010
NE340070
-1-2 Lift Box
Pin, Pivot
Ring, Retaining
1
2
2
NB340012
NB350002
0321601
ND340011
ND350001
0322001
NE340011
NE350001
0322501
-2 Roller (Upper)
(Lower)
4
4
NB351002
NB361001
ND351001
ND361001
NE351001
ND361001
-3 Washer 2 0910812 0910812 0910812
-4 Stay 2 ND391012 ND391012 ND391012
-5 Jack Plate
Screw
1
1
NB340050
0218825
ND351051
0218825
NE350050MA
0218825
Fig. N1-2 Scissor Device
for UDL-250, UDA-500 &
UDA-800

NEW STYLE DANDY LIFT OWNER'S MANUAL 17
Item No Description Qty UDA-350W
Scissor Device 1
-1-1 Scissor (Lower) 1 NC320011 (out side)
NC310010 (in side)
-1-2 Scissor (Upper)
Pin, Pivot
1
4
NC32001B (out side)
NC31001B (in side)
ND340070
-1-3 Lift Box
Ring, Retaining
1
2
NC340011
0322001
-2 Roller (upper)
(lower)
4
4
ND351001
ND361001
-3 Washer 2 0910812
-4 Stay 2 ND391012
-5 Jack Plate
Screw
1
1
ND340051
0218825
-6 Guide
Bolt
Washer, Spring
1
1
1
NC190010
0111020
0981014 Fig. N1-2'
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Frame
(not illustrated)
1 NB101002 ND101002 NE101001 NC101001
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Handle Assy 1
-1 Handle with
name plate
1 NB221012 ND220011 ND220011 ND220011
-2 Nut
Washer, Spring
2
2
0812011
0982057
0812011
0982057
0812011
0982057
0812011
0982057
Fig. N1-4

18 NEW STYLE DANDY LIFT OWNER'S MANUAL
Item
No
Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Jack Assy 1*(NA511AA1) *(ND511AA1) *(NE521AA0) *(ND511AA1)
-1 Piston 1 ND520010 ND520010 NE520010MA ND520010
-2 Spring, Compression 1 NB531001 ND531001 NE531001 ND531001
-3 Cap
Pin, Spring
1
1
ND540010
0460820
ND540010
0460820
NE540010
0460820
ND540010
0460820
-4 Nut "U"
Connecting Rod-3
1
2
0810881
ND741010
0810881
ND741010
0810881
ND741010
0810881
ND741010
*-5 Bolt
Nut
Washer, Spring
2(4)
2(4)
2(4)
0110825
0810811
0980853
0110825
0810811
0980853
0110830
0810811
0980853
0110825
0810811
0980853
-6 Jack 1 NA510000 ND510000 NE510000MA ND510000 Fig. N1-5
*Bolt, Nut & Washer Spring are not included in the jack assembly on the top line above.
*Qty of 3 pieces are to be used for UDA-800
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Caster (4 Sets)
-1 Front caster 2 38-WK-100R 38-WK-130R 38-WK-150U 38-WK-130R
-2 Rear caster 2 38-WJ-100R 38-WJ-130R 38-WJ-150U 38-WJ-130R
-3 Bolt
Washer,
Spring
Nut
16
16
16
0141020
0981064
0811011
0141020
0981064
0811011
0141020
0981064
0811011
0141020
0981064
0811011
Fig. N1-6
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Parking Lock 1
-1 Floor Lock 1 ND810000 ND810000 ND810000 ND810000
-2 Bolt 4 0110820 0110820 0110820 0110820
-3 Washer, Spring 4 0980853 0980853 0980853 0980853
-4 Nut 4 0810811 0810811 0810811 0810811
-5 Shoe 1 ND810200 ND810200 ND810200 ND810200
Fig. N1-7 5

NEW STYLE DANDY LIFT OWNER'S MANUAL 19
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Release Lever Assy 1
-1 Release Lever 1 NUD220100 NUD220100 NUD220100 NUD220100
-2 Pin, Spring 2 0460422 0460422 0460422 0460422
-3 Spring 2 NB760000 ND760000 ND760000 ND760000
-4 Fixed Support 1 UND720010 UND720010 UND720010 UND720010
-5 Screw 1 0210816 0210816 0210816 0210816
-6 Release Lever Rod 1 UNB461A1S UND461A1L UND461A1L UND461A1L
-7 Connecting Rod 1 UNB741061 UND740061 UNE740061 UNC740061
-8 Release Rod 1 UND461B04 UND461B04 UND461B04 UND461B04
-9 Crank 1 UND740031 UND740031 UND740031 UND740031
-10 Washer 1 0910813 0910813 0910813 0910813
-11 Pin, "R" 1 0340808 0340808 0340808 0340808
-12 Nut "U" 2 0810882 0810882 0810882 0810882
-13 Screw 1 0216616 0216616 0216616 0216616
-14 Washer, Spring 2 0980652 0980652 0980652 0980652
-15 Nut 2 0810611 0810611 0810611 0810611
-16 Bolt 1 0110865 0110865 0110865 0110865
-17 Washer, Spring 1 0910813 0910813 0910813 0910813
-18 Nut 1 0810812 0810812 0810812 0810812
Fig. N1-8

20 NEW STYLE DANDY LIFT OWNER'S MANUAL
Item No Description Qty UDL-250 UDA-500 UDA-800 UDA-350W
Jack Pedal Assy 1
-1 Pedal, Jack 1 UND430010 UND430010 UND430010 UND430010
-2 Pin, Split
Nut, Castle
1
1
0360630
0811652
0360630
0811652
0360630
0811652
0360630
0811652
-3 Shaft (Bolt) 1 0111675-17 0111675-17 0111675-17 0111675-17
-4 Receiver, Pedal 1 NB440012 ND440012 ND440012 ND440012
-5 Pin "R" 1 0340808 0340808 0340808 0340808
-6 Pin, Split
Washer
2
2
0362520
0910812
0362520
0910812
0362520
0910812
0362520
0910812
-7 Pin-1 2 ND420040 ND420040 ND420040 ND420040
-8 Connecting Rod
Bush
1
2
NB421012
ND410070
NC421012
ND410070
NE421012
ND410070
NC421012
ND410070
-9 Screw, Retaining 1 0212410 0212410 0212410 0212410
-10 Shaft for Lever 1 ND140061 ND140061 ND140061 ND140061
-11 Lever, Jack 1 NB410011 ND410011 ND410011 ND410011
-12 Pin-2
Ring Retaining "E"
1
1
ND410091
0320605
ND410091
0320605
ND410091
0320605
ND410091
0320605
-13 Roller 1 ND410060 ND410060 ND410060 ND410060
-14 Grease Nipple
Washer
2
2
0040600
0910612
0040600
0910612
0040600
0910612
0040600
0910612
Fig. N1-9