Spirit CE900ENT User manual

CE900 ENT Elliptical
OWNER’S MANUAL
Please carefully read this entire manual before operating your new elliptical.

1
TABLE OF CONTENTS
Important Safety Instructions………………………………………………………………… 2
Important Operation Instructions…………………………………………………………….. 3
Assembly Instructions…………………………………………………………….…………… 4
Getting On / Off Your Elliptical……………………………………………….…….............. 11
Console Operation…………………………………………………………….…….............. 13
Using heart rate transmitter………………………………………………………............... 33
System Maintenance Suite………………………………………………………………….. 34
General Maintenance………………………………………………………………………… 37
Exploded View Diagram………………………………………………………………………. 38
Parts List..………………………………………………………………………………………. 39
SE8800A-MB002_1902(SP)A

2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this exercise equipment.
WARNING - Heart rate monitoring systems may be inaccurate. Over exercising may result in
serious injury or death. If you feel faint stop exercising immediately.
◼Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet and
elliptical may result.
◼Keep children away from the elliptical. There are obvious pinch points and other caution
areas that can cause harm.
◼Keep hands away from all moving parts.
◼Never drop or insert any object into any openings.
◼Do not use outdoors.
◼Do not attempt to use your elliptical for any purpose other than for the purpose it is intended.
◼The hand pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are intended
only as exercise aids in determining heart rate trends in general.
◼Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.
◼This exercise equipment can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the exercise equipment in a
safe way and understand the hazards involved. Children shall not play with the exercise
equipment. Cleaning and user maintenance shall not be made by children without
supervision.
◼Children should be supervised to ensure that they do not play with the exercise equipment.
◼Notes on the correct posture and the fact the pedal crank training equipment of class B and C
are not suitable for therapeutic purposes
◼Be aware that the generator is producing AC power while the elliptical is being used. Do not
service the elliptical while the generator is spinning; serious electric shock could occur.
◼“WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in
serious injury or death. If you feel faint stop exercising immediately”.
◼WARNING: Injuries to health may result from incorrect or excessive training.
◼The elliptical trainer is not equipped with a free wheel and therefore the moving parts cannot
be stopped immediately.
◼WARNING: The individual human power which is required to carry out an exercise can be
different than the mechanical power displayed.
◼The exercise equipment shall be disconnected from its power source during clean, service or
maintenance.
◼This exercise equipment is not intended for use by persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge.
◼Before beginning this or any exercise program, consult a physician. This is especially
important for persons over the age of 35 or persons with pre-existing health conditions.
◼Close supervision is necessary when this exercise equipment is used by, on, or near children,
invalids, or disabled persons.
SAVE THESE INSTRUCTIONS - THINK SAFETY!

3
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING!
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use outdoors, near
a pool or spa, or in any other high humidity environment.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install the elliptical
on a flat level surface with access to a 100 to 240-volt AC, 50/60 Hz grounded outlet. Do not use an
extension cord unless it is 16awg or larger, with only one outlet on the end. The elliptical should be
the only exercise equipment in the electrical circuit. Do not attempt to disable the grounded plug by
using improper adapters, or in any way modify the cord set; a serious shock or fire hazard may result
along with computer malfunctions.
Important Operation Instructions
NEVER operate this elliptical without reading and completely understanding the results of any
operational change you request from the computer.
NEVER use your elliptical during an electrical storm. Surges may occur in your facility power
supply that could damage the elliptical’s components.
All users should have medical clearance before starting any rigorous exercise program. This is
especially important for persons with a history of heart disease or other high risk factors.
Understand that changes in resistance do not occur immediately. Set your desired resistance
level on the computer console and release the adjustment key. The computer will obey the
command gradually.

Use caution while participating in other activities while pedaling on your elliptical; such as
watching television, reading, etc. These distractions may cause you to lose balance which may
result in serious injury.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure.
Always hold on to a handle bar while making control changes.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure. If you feel the buttons are not functioning properly with normal
pressure contact your dealer.

4
ASSEMBLY INSTRUCTIONS
Max. user’s weight.: 205 kg
UNPACKING
1. Cut the straps, then lift the box over the unit and unpack.
2. Locate the hardware package. The hardware is separated into four steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing for reference.
ASSEMBLY TOOLS
#131. Phillips Head
Screw driver (1 pc)
#132. 5mm L Allen Wrench (1 pc)
#135. 17 mm
Wrench (1 pc)
#133. 6mm L Allen Wrench (1 pc)
#134. M10 L Allen Wrench (1 pc)

5
STEP 1
STEP 2
STEP 3
STEP 4
#46– 3.5 ×12mm
Sheet Metal Screw
(2pcs)
#54 – M10 × 20mm
Socket Head Cap Bolt
(12pcs)
#57 –Ø10 × 2T
Split Washer (4pcs)
#58 – Ø4 × 14 × 1.0T
Flat Washer (2pcs)
#65 – Ø3/8" × Ø19 × 1.5T
Flat Washer (4pcs)
#47 –5×16m/m
Sheet Metal Screw (2pcs)
#49 –M5×12mm
Phillips Head Screw (6pcs)
#78 –M5 ×1T Plate (2pcs)
#43 – M10 ×55mm
Socket Head Cap Bolt
(2pcs)
#44 – M10 ×60mm
Socket Head Cap Bolt
(4pcs)
#63 – Ø10 × Ø25 × 1.5T
Flat Washer (10pcs)
#68 –Ø10 × Ø23 × 1.5T
Curved Washer (2pcs)
#71 –M10 × 8T
Nyloc Nut (6pcs)
#46 –3.5 × 12m/m
Sheet Metal Screw
(2pcs)
#49 –M5×12mm
Phillips Head Screw
(6pcs)

6
STEP 1
1. Unwind wiring harness and run wires up through CONSOLE MAST (9). Bolt CONSOLE MAST (9)
to MAIN FRAME (1) using 4 BOLTS (54), 4 LOCK WASHERS (57), and 4 WASHERS (65). Do not
pinch wires.
2. Run wires from CENTER HANDLEBARS (11) through HANDLEBAR BRACKET (10), into
CONSOLE MAST (9) and out the top.
3. Install CENTER HANDLEBARS (11) to HANDLEBAR BRACKET (10) using 4 BOLTS (52).
4. Install HANDLEBAR BRACKET (10) to CONSOLE MAST (9) using 4 BOLTS (54).
5. Attach CUP HOLDER (99) to HANDLEBAR BRACKET (10) using 2 SELF-TAPPING SCREWS
(46) and 2 WASHERS (58).
6.

7
STEP 2
1. Install 2 U-NUTS (78) to LEFT CONSOLE MAST COVER (100).
2. Attach CONSOLE MAST COVERS (100 & 101) to MAIN FRAME (1) using 2 SELF-TAPPING
SCREWS (47). Use 2 SCREWS (49) to connect covers to each other.
3. Plug in all wires from wiring harness to CONSOLE (111).
4. Install CONSOLE (111) to CONSOLE MAST (9) using 4 SCREWS (49). Be careful not to pinch
any wires.

8
HDMI ETHERNET CABLE
CSAFE HAND PULSE (4PIN)
COMPUTER CABLE (8PIN)
GND HAND PULSE (3PIN)
X(NO USE) X(NO USE) X(NO USE) X(NO USE)
TV
CABLE
TFT
POWER

9
STEP 3
1. Install LEFT SIDE HANDLEBAR (2) to SWING ARM (12).
a) First install 2 longer BOLTS (44) with a WASHER (63) on both sides of SWING ARM (12)
and a NUT (71). Do not tighten yet.
b) Then install 1 SHORTER BOLT (43) with a WASHER (63) through the SWING ARM (12)
and CROSSTRAINING HANDLEBAR (2), using a CURVED WASHER (68) and a NUT (71) on
the back side.
c) Tighten after all hardware is installed.
2. Repeat process for RIGHT SIDE HANDLEBAR (3).

10
STEP 4
1.Attach CONSOLE BRACKET COVERS (91 & 92) to CONSOLE MAST (9) using 2 SCREWS
(49). Connect covers together using 2 SELF-TAPPING SCREWS (46).
2.Attach left SWING ARM HINGE COVER (93) to SWING ARM (12) using 2 SCREWS (49).
Repeat for right side.

11
GETTING ON / OFF YOUR ELLIPTICAL
IMPORTANT
The elliptical comes with two Dual Action Handles and a Stationary Handlebar.
Always hold the Stationary Handlebar when getting on and off the elliptical.
First time users should familiarize themselves with using the elliptical by using the Stationary
Handlebar first and then progressing to the Dual Action Handles.
Once you have familiarized yourself with using the elliptical, you can progress to using
the Dual Action Handles to provide a total body workout. Hands can be positioned on the
Dual Action Handles at the most appropriate position for your height and arm length.
Caution should always be taken when getting on and off any exercise machine.
Please follow the safety steps below.
Ensure the left Foot Pedal is in the lowest position and grasp the
Stationary Handlebar with both hands.
Place your left foot on the left Foot Pedal and get secure.
Lift your right foot over machine and place on right Foot Pedal. Get
balanced and begin your workout.
Important
To get off, come to a complete stop and reverse the procedure.
Always wear rubber-soled shoes, such as tennis shoes.
It is recommended that you keep at least one hand on the Stationary Handlebar at all times,
especially when getting on or off. If you are performing a walking action with your arms, or doing
upper body strength training exercises, ensure you are well balanced.
All equipment should be set-up and operated on solid, level surfaces.

12
Correct Position
Your body should be in an upright position so that your back is straight.
Keep your head up to minimize neck and upper back strain.
Always try and use the elliptical in a rhythmical and smooth motion. If
you find yourself feeling uncomfortable, or experience a surging type
feeling, there is probably too much tension.
The elliptical can be used in forward or reverse notion.
When going in reverse, bend your knees slightly more. More emphasis is on the
buttocks and hamstrings in the reverse motion.
MOVING YOUR ELLIPTICAL
The elliptical can be easily moved.
1. At the rear of the machine squat down and grasp the rear stabilizer
bar.
2. Lift the rear of the machine using your legs until the wheels in the front
engage with the ground.

13
CONSOLE OPERATION
The console

14
Starting the operation
• Plug in the power cord at the front of the elliptical.
•When the power cord is plugged in the screen will show the initial image and then enter the ready
mode which is the beginning of the elliptical operation.
Main Home page: Begin operation by touching the icons.
Quick operating buttons are convenient for basic elliptical
functions.

15
Quick Start
• PressStartbuttonandtheconsolestartsthe Quick Start program.PressLevelup/downbuttons to
change totheresistancelevelyoudesire.
• Press Home button orStop button tostop the program.
Featured functions of this elliptical
The Touch-control screen is used for operating all functions of the elliptical. You can directly touch any
key on the screen or through quick keys on the bottom to control functions. On the lower portion of the
console there is the Start key to begin the workout, Stop button to pause/stop programs, Level keys
to change workload and a Fan key to turn the fan on or off.
Pause/Stop
• Press Stop key once or Home key on the screen, the elliptical will stop and keep values of time,
distance and calorie on the screen. The screen will count down for 5 minutes then reset and return
totheinitialstatus.
• PressStartkeytocontinuetheworkoutduringpause.
• PressStopkeytwicewillterminatethesettingwithdisplayingtheworkoutsummary.IfStop
key is pressed a third time, the console will return to the initial status (the beginning).
Heart Rate Feature
The Pulse (Heart Rate) on the screen shows the current value of your heart rate in beats per
minute. You must use both left and right stainless steel sensors to pick up your pulse. Pulse values
are displayed anytime the computer is receiving a Grip Pulse signal. You may use the Grip Pulse
feature while in Heart Rate Control. The Console will also pick up wireless heart rate
transmitters that are 5 khz Polar compatible.
Wireless heartbeat device
Click on this screen to set the wireless chest strap pairing, check the paired use of the 5KHz
wireless chest strap, or the Bluetooth wireless chest strap.

16
To Turn the Elliptical Off
The screen will automatically turn off (go to sleep) after 30 minutes of inactivity. This function is
called sleep mode. In sleep mode, the elliptical will power down everything except for a minimum
of circuitry for detecting key presses, so it will start up again if this is activated. There is only a tiny
amount of current used in sleep mode (about the same as your TV when it is turned off) and it is
perfectly fine to leave the main power switch on in sleep mode.

17
Below is the instruction for touch screen operation:
• First page HOME
There are four selections. Usually the “Language” is the first selection.
•When you press “Language” button on the first page HOME, it enters the menu with all
languages selection.
There are 13 languages to choose from.
Touch the desired language button to set and the system will return to the first page for the program
operation. If you don’t want to change the language, press HOME button at the upper left corner to
return to the first page or touch the return button at right upper right corner to return to the previous
page to continue the operation.

18
• When TV button on the first page HOME is pressed, it enters TV interface.
Now you can enjoy TV programs. If you want to workout and enjoy TV program simultaneously, press
“START” button to start the elliptical.
You can change the TV channel by using up/down buttons on the TV channel or channel remote
control at bottom right to change the channel. You can use the Volume up/down keys to change the
sound levels. Press “Mute” button to switch to silence. Touch Max Screen icon to switch to full screen.
Touching anywhere on the screen will return it to the original screen size. Use level up/down buttons
to control the resistance level. When you want to pause, just press “HOME” button at left top of the
screen or press “STOP” button once and the pause window will show up. If you want to stop, you can
choose to end the program or press “STOP” button again to end the program and display the workout
summary. Pressing the “STOP” button third time and the console returns to the initial status (the
beginning).

19
• When you touch “Internet” button on HOME first page, it rapidly enters internet
interface.
There are 6 internet connections to choose from while you are exercising. (internet cable connection
or WIFI connection is required) Press “START” button of the elliptical to begin exercise.
Use “level up/down buttons to control the resistance level during the exercise. When you want to
pause, just press “HOME” button at left top or press “STOP” button once and the pause window will
show up. If you want to end, you can choose to end the program or press “STOP” button again to
show the workout summary. If “STOP” button is pressed the third time, the console will return to the
initial status. (the beginning)